lkml.org 
[lkml]   [2009]   [Oct]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: pci-express hotplug
On Tue, Oct 27 2009, Kenji Kaneshige wrote:
> Jens Axboe wrote:
>> On Tue, Oct 20 2009, Alex Chiang wrote:
>>> * Jens Axboe <jens.axboe@oracle.com>:
>>>> On Tue, Oct 13 2009, Alex Chiang wrote:
>>>>>>> Can you modprobe acpiphp with debug=1? And send the output?
>>>>>> acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
>>>>>> acpiphp_glue: found PCI-to-PCI bridge at PCI 0000:00:05.0
>>>>>> acpiphp_glue: found ACPI PCI Hotplug slot 1 at PCI 0000:08:00
>>>>>> acpiphp: Slot [1] registered
>>>>>> acpiphp_glue: found PCI-to-PCI bridge at PCI 0000:00:07.0
>>>>>> acpiphp_glue: found ACPI PCI Hotplug slot 2 at PCI 0000:0b:00
>>>>>> acpiphp: Slot [2] registered
>>>>>> acpiphp_glue: found PCI-to-PCI bridge at PCI 0000:80:07.0
>>>>>> acpiphp_glue: found ACPI PCI Hotplug slot 6 at PCI 0000:84:00
>>>>>> acpiphp: Slot [6] registered
>>>>>> acpiphp_glue: found PCI-to-PCI bridge at PCI 0000:80:09.0
>>>>>> acpiphp_glue: found ACPI PCI Hotplug slot 7 at PCI 0000:87:00
>>>>>> acpiphp: Slot [7] registered
>>>>>> acpiphp_glue: Bus 0000:87 has 1 slot
>>>>>> acpiphp_glue: Bus 0000:84 has 1 slot
>>>>>> acpiphp_glue: Bus 0000:0b has 1 slot
>>>>>> acpiphp_glue: Bus 0000:08 has 1 slot
>>>>>> acpiphp_glue: Total 4 slots
>>>>> You mentioned in another mail that you echoed 1 into the various
>>>>> slots' power files.
>>>>>
>>>>> Did you do that after modprobing acpiphp with debug=1?
>>>>>
>>>>> If so, there should be debug output when you try and turn them
>>>>> on.
>>>> It produces:
>>>>
>>>> acpiphp: enable_slot - physical_slot = 1
>>>> acpiphp_glue: acpiphp_enable_slot: Slot status is not ACPI_STA_ALL
>>>> acpiphp: enable_slot - physical_slot = 2
>>>> acpiphp_glue: acpiphp_enable_slot: Slot status is not ACPI_STA_ALL
>>>> acpiphp: enable_slot - physical_slot = 6
>>>> acpiphp_glue: acpiphp_enable_slot: Slot status is not ACPI_STA_ALL
>>>> acpiphp: enable_slot - physical_slot = 7
>>>> acpiphp_glue: acpiphp_enable_slot: Slot status is not ACPI_STA_ALL
>>> Hm, so for some reason, firmware on your machine is telling us
>>> that it doesn't think cards are present and/or enabled.
>>>
>>> Unfortunately, I don't know why your firmware would be saying
>>> that. We could add some more debug printks to see what firmware
>>> thinks about your system... Or we could just wait and see what
>>> happens after you get your hardware replaced.
>>
>> New board, the exact same thing happens.
>>
>>>> I have a card in one of the slots only this time.
>>>>
>>>>> Also, quick dummy check, you are trying to power on populated
>>>>> slots, right? :)
>>>> Yes :-)
>>>>
>>>>> Can you send the output of lspci -vv? And I like the output of
>>>>> lspci -vt as well... Both before and after loading acpiphp
>>>>> please.
>>>> Send privately.
>>> No difference in before and after. Odd.
>>>
>>> If you want to poke us again after your hardware swap, please do
>>> so. Sorry for being not so helpful. :-/
>>
>> Poke :-)
>>
>> One more thing I tried was pushing the power button on the slot
>> manually. With acpiphp, I get the same messages as above. Using pciehp,
>> I get the same power fault bit interrupt storm. So no difference from
>> using the sysfs interface or doing it on the box side, doesn't work
>> either way.
>>
>
> I'd like to confirm power fault interrupt storm, just in case.
> Could you get /proc/interrupts information after power fault
> problem happens and send it to me?

The box pretty much hangs when I try to power on a slot with pciehp, so
it's not easy to do... It doesn't hang with acpiphp, but doesn't work
either (see previous reply to Alex).

--
Jens Axboe



\
 
 \ /
  Last update: 2009-10-27 09:29    [W:0.113 / U:0.088 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site