lkml.org 
[lkml]   [2009]   [Oct]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    SubjectRe: [REGRESSION] "bind" a device to a driver doesn't not work anymore
    Op 15-10-09 20:13, Dmitry Torokhov schreef:
    > It lokks like the keyboard controller switched from translated to
    > non-translated mode: '1c' is make code and 'f0 1c' is break (aka
    > release) code.
    >
    > Could you tell me how the keyboard indentified (in dmesg) after fresh
    > boot and after you do the bind/unbind trick on the older kernel?
    >
    What do you mean by "how the keyboard indentified"? Are you asking for
    the debug trace in dmesg? I have the beginning of a boot with the debug
    trace to see after a fresh boot. I don't have dmesg history with
    i8042.debug of the bind/unbind trick, so I'll reboot in an old kernel
    and do it again (but I cannot do this before tuesday, when i have
    physical access to the machine).

    > sftp://piel@localhost:2226/home/piel/busy/i8042-begin-boot-keyboard.dmesg

    > BTW, do you have i8042.reset parameyer on your command line? What
    > happens if you remove it?
    The two logs where done with i8042.reset. However, without this
    parameter, the behaviour is identical: the keyboard needs the
    unbind/bind trick after the first resume.

    Eric
    Linux version 2.6.32-rc3-git-eric-00343-g35578ca (piel@dutifh) (gcc version 4.4.1 (GCC) ) #17 SMP PREEMPT Mon Oct 12 18:54:14 CEST 2009
    Command line: BOOT_IMAGE=2632-rc3-git-eric-00343-g35578c root=UUID=01dc5fcc-55d3-4bae-932b-1119dbe7ff0b resume=UUID=0d777318-dc2d-4ec3-aa25-fbad7e0fa039 splash=silent i8042.debug i8042.reset vga=791
    KERNEL supported cpus:
    Intel GenuineIntel
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000007f7b0000 (usable)
    BIOS-e820: 000000007f7b0000 - 000000007f7c5400 (reserved)
    BIOS-e820: 000000007f7c5400 - 000000007f7e7fb8 (ACPI NVS)
    BIOS-e820: 000000007f7e7fb8 - 0000000080000000 (reserved)
    BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
    BIOS-e820: 00000000fed20000 - 00000000fed9a000 (reserved)
    BIOS-e820: 00000000feda0000 - 00000000fedc0000 (reserved)
    BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
    BIOS-e820: 00000000ffb00000 - 00000000ffc00000 (reserved)
    BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
    DMI 2.4 present.
    last_pfn = 0x7f7b0 max_arch_pfn = 0x400000000
    MTRR default type: uncachable
    MTRR fixed ranges enabled:
    00000-9FFFF write-back
    A0000-BFFFF uncachable
    C0000-D3FFF write-protect
    D4000-EFFFF uncachable
    F0000-FFFFF write-protect
    MTRR variable ranges enabled:
    0 base 000000000 mask F80000000 write-back
    1 base 07F800000 mask FFF800000 uncachable
    2 base 0FEDA0000 mask FFFFE0000 uncachable
    3 disabled
    4 disabled
    5 disabled
    6 disabled
    7 disabled
    x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    original variable MTRRs
    reg 0, base: 0GB, range: 2GB, type WB
    reg 1, base: 2040MB, range: 8MB, type UC
    reg 2, base: 4175488KB, range: 128KB, type UC
    total RAM coverred: 2040M
    Found optimal setting for mtrr clean up
    gran_size: 64K chunk_size: 16M num_reg: 2 lose cover RAM: 0G
    New variable MTRRs
    reg 0, base: 0GB, range: 2GB, type WB
    reg 1, base: 2040MB, range: 8MB, type UC
    initial memory mapped : 0 - 20000000
    init_memory_mapping: 0000000000000000-000000007f7b0000
    0000000000 - 007f600000 page 2M
    007f600000 - 007f7b0000 page 4k
    kernel direct mapping tables up to 7f7b0000 @ 8000-c000
    RAMDISK: 37666000 - 37fefab0
    ACPI: RSDP 00000000000f7980 00024 (v02 HP )
    ACPI: XSDT 000000007f7c81c4 00074 (v01 HPQOEM SLIC-MPC 00000001 HP 00000001)
    ACPI: FACP 000000007f7c8084 000F4 (v04 HP 30C9 00000003 HP 00000001)
    ACPI: DSDT 000000007f7c84c0 13484 (v01 HP nc2500 00010000 MSFT 03000001)
    ACPI: FACS 000000007f7e7d80 00040
    ACPI: SLIC 000000007f7c8238 00176 (v01 HPQOEM SLIC-MPC 00000001 HP 00000001)
    ACPI: HPET 000000007f7c83b0 00038 (v01 HP 30C9 00000001 HP 00000001)
    ACPI: APIC 000000007f7c83e8 00068 (v01 HP 30C9 00000001 HP 00000001)
    ACPI: MCFG 000000007f7c8450 0003C (v01 HP 30C9 00000001 HP 00000001)
    ACPI: TCPA 000000007f7c848c 00032 (v02 HP 30C9 00000001 HP 00000001)
    ACPI: SSDT 000000007f7db944 002BE (v01 HP HPQPAT 00000001 MSFT 03000001)
    ACPI: SSDT 000000007f7dc586 0025F (v01 HP Cpu0Tst 00003000 INTL 20060317)
    ACPI: SSDT 000000007f7dc7e5 000A6 (v01 HP Cpu1Tst 00003000 INTL 20060317)
    ACPI: SSDT 000000007f7dc88b 004D7 (v01 HP CpuPm 00003000 INTL 20060317)
    ACPI: Local APIC address 0xfee00000
    (7 early reservations) ==> bootmem [0000000000 - 007f7b0000]
    #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
    #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
    #2 [0001000000 - 00019daa64] TEXT DATA BSS ==> [0001000000 - 00019daa64]
    #3 [0037666000 - 0037fefab0] RAMDISK ==> [0037666000 - 0037fefab0]
    #4 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
    #5 [00019db000 - 00019db18c] BRK ==> [00019db000 - 00019db18c]
    #6 [0000008000 - 000000a000] PGTABLE ==> [0000008000 - 000000a000]
    Zone PFN ranges:
    DMA 0x00000000 -> 0x00001000
    DMA32 0x00001000 -> 0x00100000
    Normal 0x00100000 -> 0x00100000
    Movable zone start PFN for each node
    early_node_map[2] active PFN ranges
    0: 0x00000000 -> 0x0000009f
    0: 0x00000100 -> 0x0007f7b0
    On node 0 totalpages: 522063
    DMA zone: 56 pages used for memmap
    DMA zone: 101 pages reserved
    DMA zone: 3842 pages, LIFO batch:0
    DMA32 zone: 7083 pages used for memmap
    DMA32 zone: 510981 pages, LIFO batch:31
    ACPI: PM-Timer IO Port: 0x1008
    ACPI: Local APIC address 0xfee00000
    ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
    ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
    ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
    ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
    ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
    IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
    ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    ACPI: IRQ0 used by override.
    ACPI: IRQ2 used by override.
    ACPI: IRQ9 used by override.
    Using ACPI (MADT) for SMP configuration information
    ACPI: HPET id: 0x8086a201 base: 0xfed00000
    SMP: Allowing 2 CPUs, 0 hotplug CPUs
    nr_irqs_gsi: 24
    PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
    PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
    PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
    Allocating PCI resources starting at 80000000 (gap: 80000000:7ec00000)
    Booting paravirtualized kernel on bare hardware
    NR_CPUS:4096 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1
    PERCPU: Embedded 28 pages/cpu @ffff880001a00000 s85400 r8192 d21096 u1048576
    pcpu-alloc: s85400 r8192 d21096 u1048576 alloc=1*2097152
    pcpu-alloc: [0] 0 1
    Built 1 zonelists in Zone order, mobility grouping on. Total pages: 514823
    Kernel command line: BOOT_IMAGE=2632-rc3-git-eric-00343-g35578c root=UUID=01dc5fcc-55d3-4bae-932b-1119dbe7ff0b resume=UUID=0d777318-dc2d-4ec3-aa25-fbad7e0fa039 splash=silent i8042.debug i8042.reset vga=791
    PID hash table entries: 4096 (order: 3, 32768 bytes)
    Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
    Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
    Initializing CPU#0
    Memory: 2035536k/2088640k available (4036k kernel code, 388k absent, 51984k reserved, 4576k data, 552k init)
    SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
    Experimental preemptable hierarchical RCU implementation.
    NR_IRQS:33024 nr_irqs:424
    Extended CMOS year: 2000
    Console: colour dummy device 80x25
    console [tty0] enabled
    hpet clockevent registered
    HPET: 3 timers in total, 0 timers will be used for per-cpu timer
    Fast TSC calibration using PIT
    Detected 1196.971 MHz processor.
    Calibrating delay loop (skipped), value calculated using timer frequency.. 2393.94 BogoMIPS (lpj=1196971)
    Mount-cache hash table entries: 256
    Initializing cgroup subsys ns
    Initializing cgroup subsys cpuacct
    Initializing cgroup subsys devices
    Initializing cgroup subsys freezer
    CPU: L1 I cache: 32K, L1 D cache: 32K
    CPU: L2 cache: 2048K
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 0
    mce: CPU supports 6 MCE banks
    CPU0: Thermal monitoring handled by SMI
    using mwait in idle threads.
    Performance Events: Core2 events, Intel PMU driver.
    ... version: 2
    ... bit width: 40
    ... generic registers: 2
    ... value mask: 000000ffffffffff
    ... max period: 000000007fffffff
    ... fixed-purpose events: 3
    ... event mask: 0000000700000003
    ACPI: Core revision 20090903
    Setting APIC routing to flat
    ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    CPU0: Intel(R) Core(TM)2 Duo CPU U7600 @ 1.20GHz stepping 0d
    Booting processor 1 APIC 0x1 ip 0x6000
    Initializing CPU#1
    Calibrating delay using timer specific routine.. 2393.89 BogoMIPS (lpj=1196949)
    CPU: L1 I cache: 32K, L1 D cache: 32K
    CPU: L2 cache: 2048K
    CPU: Physical Processor ID: 0
    CPU: Processor Core ID: 1
    mce: CPU supports 6 MCE banks
    CPU1: Thermal monitoring enabled (TM2)
    CPU1: Intel(R) Core(TM)2 Duo CPU U7600 @ 1.20GHz stepping 0d
    checking TSC synchronization [CPU#0 -> CPU#1]: passed.
    Brought up 2 CPUs
    Total of 2 processors activated (4787.84 BogoMIPS).
    CPU0 attaching sched-domain:
    domain 0: span 0-1 level MC
    groups: 0 1
    CPU1 attaching sched-domain:
    domain 0: span 0-1 level MC
    groups: 1 0
    NET: Registered protocol family 16
    ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
    ACPI: bus type pci registered
    PCI: MCFG configuration 0: base f8000000 segment 0 buses 0 - 63
    PCI: Not using MMCONFIG.
    PCI: Using configuration type 1 for base access
    bio: create slab <bio-0> at 0
    ACPI: EC: Look up EC in DSDT
    ACPI: Interpreter enabled
    ACPI: (supports S0 S3 S4 S5)
    ACPI: Using IOAPIC for interrupt routing
    PCI: MCFG configuration 0: base f8000000 segment 0 buses 0 - 63
    PCI: MCFG area at f8000000 reserved in ACPI motherboard resources
    PCI: Using MMCONFIG at f8000000 - fbffffff
    ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62
    ACPI: Power Resource [C29F] (on)
    ACPI: Power Resource [C1C7] (off)
    ACPI: Power Resource [C3AD] (off)
    ACPI: Power Resource [C3B0] (off)
    ACPI: Power Resource [C3C3] (off)
    ACPI: Power Resource [C3C4] (off)
    ACPI: Power Resource [C3C5] (off)
    ACPI: Power Resource [C3C6] (off)
    ACPI: Power Resource [C3C7] (off)
    ACPI: No dock devices found.
    ACPI: PCI Root Bridge [C003] (0000:00)
    pci 0000:00:02.0: reg 10 64bit mmio: [0xe0400000-0xe04fffff]
    pci 0000:00:02.0: reg 18 64bit mmio pref: [0xd0000000-0xdfffffff]
    pci 0000:00:02.0: reg 20 io port: [0x2000-0x2007]
    pci 0000:00:02.1: reg 10 64bit mmio: [0xe0500000-0xe05fffff]
    pci 0000:00:19.0: reg 10 32bit mmio: [0xe0600000-0xe061ffff]
    pci 0000:00:19.0: reg 14 32bit mmio: [0xe0620000-0xe0620fff]
    pci 0000:00:19.0: reg 18 io port: [0x2020-0x203f]
    pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
    pci 0000:00:19.0: PME# disabled
    pci 0000:00:1a.0: reg 20 io port: [0x2040-0x205f]
    pci 0000:00:1a.1: reg 20 io port: [0x2060-0x207f]
    pci 0000:00:1a.7: reg 10 32bit mmio: [0xe0621000-0xe06213ff]
    pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
    pci 0000:00:1a.7: PME# disabled
    pci 0000:00:1b.0: reg 10 64bit mmio: [0xe0624000-0xe0627fff]
    pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
    pci 0000:00:1b.0: PME# disabled
    pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
    pci 0000:00:1c.0: PME# disabled
    pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
    pci 0000:00:1c.1: PME# disabled
    pci 0000:00:1d.0: reg 20 io port: [0x2080-0x209f]
    pci 0000:00:1d.1: reg 20 io port: [0x20a0-0x20bf]
    pci 0000:00:1d.2: reg 20 io port: [0x20c0-0x20df]
    pci 0000:00:1d.7: reg 10 32bit mmio: [0xe0628000-0xe06283ff]
    pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
    pci 0000:00:1d.7: PME# disabled
    pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
    pci 0000:00:1f.0: quirk: region 1100-113f claimed by ICH6 GPIO
    pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0500 (mask 007f)
    pci 0000:00:1f.0: ICH7 LPC Generic IO decode 4 PIO at 02e8 (mask 0007)
    pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
    pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
    pci 0000:00:1f.1: reg 18 io port: [0x00-0x07]
    pci 0000:00:1f.1: reg 1c io port: [0x00-0x03]
    pci 0000:00:1f.1: reg 20 io port: [0x20e0-0x20ef]
    pci 0000:10:00.0: reg 10 64bit mmio: [0xe0000000-0xe0003fff]
    pci 0000:10:00.0: supports D1 D2
    pci 0000:00:1c.1: bridge 32bit mmio: [0xe0000000-0xe00fffff]
    pci 0000:02:06.0: reg 10 32bit mmio: [0xe0100000-0xe0100fff]
    pci 0000:02:06.0: supports D1 D2
    pci 0000:02:06.0: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:02:06.0: PME# disabled
    pci 0000:02:06.1: reg 10 32bit mmio: [0xe0101000-0xe01017ff]
    pci 0000:02:06.1: supports D1 D2
    pci 0000:02:06.1: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:02:06.1: PME# disabled
    pci 0000:02:06.2: reg 10 32bit mmio: [0xe0102000-0xe01020ff]
    pci 0000:02:06.2: supports D1 D2
    pci 0000:02:06.2: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:02:06.2: PME# disabled
    pci 0000:02:06.3: reg 10 32bit mmio: [0xe0103000-0xe01030ff]
    pci 0000:02:06.3: supports D1 D2
    pci 0000:02:06.3: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:02:06.3: PME# disabled
    pci 0000:00:1e.0: transparent bridge
    pci 0000:00:1e.0: bridge 32bit mmio: [0xe0100000-0xe03fffff]
    pci_bus 0000:00: on NUMA node 0
    ACPI: PCI Interrupt Routing Table [\_SB_.C003._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.C003.C0B2._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.C003.C11F._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.C003.C133._PRT]
    ACPI: PCI Interrupt Link [C12F] (IRQs *10 11)
    ACPI: PCI Interrupt Link [C130] (IRQs *10 11)
    ACPI: PCI Interrupt Link [C131] (IRQs 10 *11)
    ACPI: PCI Interrupt Link [C132] (IRQs 10 11) *5
    ACPI: PCI Interrupt Link [C142] (IRQs *10 11)
    ACPI: PCI Interrupt Link [C143] (IRQs 10 11) *0, disabled.
    ACPI: PCI Interrupt Link [C144] (IRQs 10 *11)
    ACPI Exception: AE_NOT_FOUND, Evaluating _PRS (20090903/pci_link-184)
    SCSI subsystem initialized
    libata version 3.00 loaded.
    PCI: Using ACPI for IRQ routing
    hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
    hpet0: 3 comparators, 64-bit 14.318180 MHz counter
    Switching to clocksource tsc
    pnp: PnP ACPI init
    ACPI: bus type pnp registered
    alloc irq_desc for 23 on node -1
    alloc kstat_irqs on node -1
    pnp: PnP ACPI: found 14 devices
    ACPI: ACPI bus type pnp unregistered
    system 00:00: iomem range 0x0-0x9ffff could not be reserved
    system 00:00: iomem range 0xe0000-0xfffff could not be reserved
    system 00:00: iomem range 0x100000-0x7f7fffff could not be reserved
    system 00:0a: ioport range 0x500-0x55f has been reserved
    system 00:0a: ioport range 0x800-0x80f has been reserved
    system 00:0a: iomem range 0xffb00000-0xffbfffff has been reserved
    system 00:0a: iomem range 0xfff00000-0xffffffff has been reserved
    system 00:0c: ioport range 0x4d0-0x4d1 has been reserved
    system 00:0c: ioport range 0x2f8-0x2ff has been reserved
    system 00:0c: ioport range 0x3f8-0x3ff has been reserved
    system 00:0c: ioport range 0x1000-0x107f has been reserved
    system 00:0c: ioport range 0x1100-0x113f has been reserved
    system 00:0c: ioport range 0x1200-0x121f has been reserved
    system 00:0c: iomem range 0xf8000000-0xfbffffff has been reserved
    system 00:0c: iomem range 0xfec00000-0xfec000ff could not be reserved
    system 00:0c: iomem range 0xfed20000-0xfed3ffff has been reserved
    system 00:0c: iomem range 0xfed45000-0xfed8ffff has been reserved
    system 00:0c: iomem range 0xfed90000-0xfed99fff has been reserved
    system 00:0d: iomem range 0xcee00-0xcffff has been reserved
    system 00:0d: iomem range 0xd2000-0xd3fff has been reserved
    system 00:0d: iomem range 0xfeda0000-0xfedbffff has been reserved
    system 00:0d: iomem range 0xfee00000-0xfee00fff has been reserved
    pci 0000:00:1c.0: PCI bridge, secondary bus 0000:08
    pci 0000:00:1c.0: IO window: disabled
    pci 0000:00:1c.0: MEM window: disabled
    pci 0000:00:1c.0: PREFETCH window: disabled
    pci 0000:00:1c.1: PCI bridge, secondary bus 0000:10
    pci 0000:00:1c.1: IO window: disabled
    pci 0000:00:1c.1: MEM window: 0xe0000000-0xe00fffff
    pci 0000:00:1c.1: PREFETCH window: disabled
    pci 0000:02:06.0: CardBus bridge, secondary bus 0000:03
    pci 0000:02:06.0: IO window: 0x003000-0x0030ff
    pci 0000:02:06.0: IO window: 0x003400-0x0034ff
    pci 0000:02:06.0: PREFETCH window: 0x80000000-0x83ffffff
    pci 0000:02:06.0: MEM window: 0x84000000-0x87ffffff
    pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
    pci 0000:00:1e.0: IO window: 0x3000-0x3fff
    pci 0000:00:1e.0: MEM window: 0xe0100000-0xe03fffff
    pci 0000:00:1e.0: PREFETCH window: 0x80000000-0x83ffffff
    alloc irq_desc for 16 on node -1
    alloc kstat_irqs on node -1
    pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    pci 0000:00:1c.0: setting latency timer to 64
    alloc irq_desc for 17 on node -1
    alloc kstat_irqs on node -1
    pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    pci 0000:00:1c.1: setting latency timer to 64
    pci 0000:00:1e.0: setting latency timer to 64
    alloc irq_desc for 18 on node -1
    alloc kstat_irqs on node -1
    pci 0000:02:06.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
    pci_bus 0000:00: resource 0 io: [0x00-0xffff]
    pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
    pci_bus 0000:10: resource 1 mem: [0xe0000000-0xe00fffff]
    pci_bus 0000:02: resource 0 io: [0x3000-0x3fff]
    pci_bus 0000:02: resource 1 mem: [0xe0100000-0xe03fffff]
    pci_bus 0000:02: resource 2 pref mem [0x80000000-0x83ffffff]
    pci_bus 0000:02: resource 3 io: [0x00-0xffff]
    pci_bus 0000:02: resource 4 mem: [0x000000-0xffffffffffffffff]
    pci_bus 0000:03: resource 0 io: [0x3000-0x30ff]
    pci_bus 0000:03: resource 1 io: [0x3400-0x34ff]
    pci_bus 0000:03: resource 2 pref mem [0x80000000-0x83ffffff]
    pci_bus 0000:03: resource 3 mem: [0x84000000-0x87ffffff]
    NET: Registered protocol family 2
    IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
    TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
    TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
    TCP: Hash tables configured (established 262144 bind 65536)
    TCP reno registered
    NET: Registered protocol family 1
    Trying to unpack rootfs image as initramfs...
    Freeing initrd memory: 9766k freed
    audit: initializing netlink socket (disabled)
    type=2000 audit(1255634791.705:1): initialized
    VFS: Disk quotas dquot_6.5.2
    Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    msgmni has been set to 3996
    alg: No test for stdrng (krng)
    Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
    io scheduler noop registered
    io scheduler deadline registered
    io scheduler cfq registered (default)
    pci 0000:00:02.0: Boot video device
    alloc irq_desc for 24 on node -1
    alloc kstat_irqs on node -1
    pcieport-driver 0000:00:1c.0: irq 24 for MSI/MSI-X
    pcieport-driver 0000:00:1c.0: setting latency timer to 64
    alloc irq_desc for 25 on node -1
    alloc kstat_irqs on node -1
    pcieport-driver 0000:00:1c.1: irq 25 for MSI/MSI-X
    pcieport-driver 0000:00:1c.1: setting latency timer to 64
    vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90004100000, using 3072k, total 7616k
    vesafb: mode is 1024x768x16, linelength=2048, pages=3
    vesafb: scrolling: redraw
    vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
    Console: switching to colour frame buffer device 128x48
    fb0: VESA VGA frame buffer device
    Linux agpgart interface v0.103
    agpgart-intel 0000:00:00.0: Intel 965GM Chipset
    agpgart-intel 0000:00:00.0: detected 7676K stolen memory
    agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
    Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
    brd: module loaded
    ata_piix 0000:00:1f.1: version 2.13
    ata_piix 0000:00:1f.1: quirky BIOS, skipping spindown on poweroff and hibernation
    ata_piix 0000:00:1f.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    ata_piix 0000:00:1f.1: setting latency timer to 64
    scsi0 : ata_piix
    scsi1 : ata_piix
    ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x20e0 irq 14
    ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x20e8 irq 15
    ata2: port disabled. ignoring.
    PNP: PS/2 Controller [PNP0303:C29C,PNP0f13:C29D] at 0x60,0x64 irq 1,12
    drivers/input/serio/i8042.c: aa -> i8042 (command) [1]
    drivers/input/serio/i8042.c: 55 <- i8042 (return) [1]
    drivers/input/serio/i8042.c: 20 -> i8042 (command) [1]
    drivers/input/serio/i8042.c: 30 <- i8042 (return) [1]
    drivers/input/serio/i8042.c: 60 -> i8042 (command) [1]
    drivers/input/serio/i8042.c: 30 -> i8042 (parameter) [1]
    drivers/input/serio/i8042.c: d3 -> i8042 (command) [1]
    drivers/input/serio/i8042.c: 5a -> i8042 (parameter) [1]
    drivers/input/serio/i8042.c: 5a <- i8042 (return) [1]
    drivers/input/serio/i8042.c: a7 -> i8042 (command) [1]
    drivers/input/serio/i8042.c: 20 -> i8042 (command) [2]
    drivers/input/serio/i8042.c: 30 <- i8042 (return) [2]
    drivers/input/serio/i8042.c: a8 -> i8042 (command) [2]
    drivers/input/serio/i8042.c: 20 -> i8042 (command) [2]
    drivers/input/serio/i8042.c: 10 <- i8042 (return) [2]
    drivers/input/serio/i8042.c: 60 -> i8042 (command) [2]
    drivers/input/serio/i8042.c: 30 -> i8042 (parameter) [2]
    drivers/input/serio/i8042.c: d3 -> i8042 (command) [2]
    drivers/input/serio/i8042.c: f0 -> i8042 (parameter) [2]
    drivers/input/serio/i8042.c: f0 <- i8042 (return) [2]
    drivers/input/serio/i8042.c: d3 -> i8042 (command) [2]
    drivers/input/serio/i8042.c: 56 -> i8042 (parameter) [2]
    drivers/input/serio/i8042.c: 56 <- i8042 (return) [2]
    drivers/input/serio/i8042.c: d3 -> i8042 (command) [2]
    drivers/input/serio/i8042.c: a4 -> i8042 (parameter) [2]
    drivers/input/serio/i8042.c: 11 <- i8042 (return) [3]
    i8042.c: Detected active multiplexing controller, rev 1.1.
    drivers/input/serio/i8042.c: 60 -> i8042 (command) [3]
    drivers/input/serio/i8042.c: 30 -> i8042 (parameter) [3]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [3]
    drivers/input/serio/i8042.c: a8 -> i8042 (command) [3]
    drivers/input/serio/i8042.c: 91 -> i8042 (command) [3]
    drivers/input/serio/i8042.c: a8 -> i8042 (command) [3]
    drivers/input/serio/i8042.c: 92 -> i8042 (command) [3]
    drivers/input/serio/i8042.c: a8 -> i8042 (command) [3]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [3]
    drivers/input/serio/i8042.c: a8 -> i8042 (command) [3]
    drivers/input/serio/i8042.c: 60 -> i8042 (command) [3]
    drivers/input/serio/i8042.c: 12 -> i8042 (parameter) [3]
    drivers/input/serio/i8042.c: 60 -> i8042 (command) [3]
    drivers/input/serio/i8042.c: 03 -> i8042 (parameter) [4]
    serio: i8042 KBD port at 0x60,0x64 irq 1
    serio: i8042 AUX0 port at 0x60,0x64 irq 12
    serio: i8042 AUX1 port at 0x60,0x64 irq 12
    serio: i8042 AUX2 port at 0x60,0x64 irq 12
    serio: i8042 AUX3 port at 0x60,0x64 irq 12
    mice: PS/2 mouse device common for all mice
    Driver 'rtc_cmos' needs updating - please use bus_type methods
    rtc_cmos 00:06: RTC can wake from S4
    rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
    rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
    cpuidle: using governor ladder
    cpuidle: using governor menu
    TCP cubic registered
    ata1.00: ATA-7: TOSHIBA MK8009GAH, BS021C, max UDMA/100
    ata1.00: 156301488 sectors, multi 16: LBA
    ata1.01: ATAPI: HL-DT-ST DVDRAM GSA-U10N, HP06, max MWDMA2
    ata1.00: configured for UDMA/100
    ata1.01: configured for MWDMA2
    scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK8009GA BS02 PQ: 0 ANSI: 5
    sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
    scsi 0:0:1:0: CD-ROM HL-DT-ST DVDRAM GSA-U10N HP06 PQ: 0 ANSI: 5
    sd 0:0:0:0: [sda] Write Protect is off
    sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sda: sda1 sda2 < sda5 sda6 sda7 >
    sd 0:0:0:0: [sda] Attached SCSI disk
    registered taskstats version 1
    rtc_cmos 00:06: setting system clock to 2009-10-15 19:26:32 UTC (1255634792)
    BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
    Freeing unused kernel memory: 552k freed
    Write protecting the kernel read-only data: 5604k
    input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
    ACPI: Sleep Button [C2BF]
    input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1
    ACPI: Lid Switch [C155]
    input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
    ACPI: Power Button [PWRF]
    [drm] Initialized drm 1.1.0 20060810
    i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    i915 0000:00:02.0: setting latency timer to 64
    alloc irq_desc for 26 on node -1
    alloc kstat_irqs on node -1
    i915 0000:00:02.0: irq 26 for MSI/MSI-X
    [drm] set up 7M of stolen space
    [drm] TV-14: set mode NTSC 480i 0
    fb: conflicting fb hw usage inteldrmfb vs VESA VGA - removing generic driver
    Console: switching to colour dummy device 80x25
    Console: switching to colour frame buffer device 160x50
    [drm] DAC-6: set mode 1920x1200 2a
    [drm] LVDS-8: set mode 1280x800 2b
    fb0: inteldrmfb frame buffer device
    registered panic notifier
    acpi device:00: registered as cooling_device0
    input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input3
    ACPI: Video Device [C09A] (multi-head: yes rom: no post: no)
    [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
    drivers/input/serio/i8042.c: f2 -> i8042 (kbd-data) [2206]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [2206]
    drivers/input/serio/i8042.c: ab <- i8042 (interrupt, 0, 1) [2209]
    drivers/input/serio/i8042.c: 83 <- i8042 (interrupt, 0, 1) [2212]
    drivers/input/serio/i8042.c: f4 -> i8042 (kbd-data) [2212]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [2215]
    input: AT Raw Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [2215]
    drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [2215]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [2218]
    drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 2, 12) [2219]
    drivers/input/serio/i8042.c: 91 -> i8042 (command) [2219]
    drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [2219]
    drivers/input/serio/i8042.c: MUX error, status is 75, data is fe [2219]
    drivers/input/serio/i8042.c: fe <- i8042 (interrupt, 3, 12, timeout) [2219]
    drivers/input/serio/i8042.c: 91 -> i8042 (command) [2219]
    drivers/input/serio/i8042.c: ed -> i8042 (parameter) [2219]
    drivers/input/serio/i8042.c: MUX error, status is 75, data is fe [2220]
    drivers/input/serio/i8042.c: fe <- i8042 (interrupt, 3, 12, timeout) [2220]
    drivers/input/serio/i8042.c: 92 -> i8042 (command) [2220]
    drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [2220]
    drivers/input/serio/i8042.c: MUX error, status is b5, data is fe [2221]
    drivers/input/serio/i8042.c: fe <- i8042 (interrupt, 4, 12, timeout) [2221]
    drivers/input/serio/i8042.c: 92 -> i8042 (command) [2221]
    drivers/input/serio/i8042.c: ed -> i8042 (parameter) [2221]
    drivers/input/serio/i8042.c: MUX error, status is b5, data is fe [2222]
    drivers/input/serio/i8042.c: fe <- i8042 (interrupt, 4, 12, timeout) [2222]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [2222]
    drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [2222]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [2225]
    drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 5, 12) [2226]
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    usbcore: registered new interface driver hiddev
    usbcore: registered new interface driver usbhid
    usbhid: v2.6:USB HID core driver
    ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
    ehci_hcd 0000:00:1a.7: setting latency timer to 64
    ehci_hcd 0000:00:1a.7: EHCI Host Controller
    ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
    ehci_hcd 0000:00:1a.7: debug port 1
    ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
    ehci_hcd 0000:00:1a.7: irq 18, io mem 0xe0621000
    ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 4 ports detected
    alloc irq_desc for 20 on node -1
    alloc kstat_irqs on node -1
    ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
    ehci_hcd 0000:00:1d.7: setting latency timer to 64
    ehci_hcd 0000:00:1d.7: EHCI Host Controller
    ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
    ehci_hcd 0000:00:1d.7: debug port 1
    ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
    ehci_hcd 0000:00:1d.7: irq 20, io mem 0xe0628000
    ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 6 ports detected
    b43-pci-bridge 0000:10:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
    b43-pci-bridge 0000:10:00.0: setting latency timer to 64
    ssb: Sonics Silicon Backplane found on PCI device 0000:10:00.0
    ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    uhci_hcd: USB Universal Host Controller Interface driver
    uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    uhci_hcd 0000:00:1a.0: setting latency timer to 64
    uhci_hcd 0000:00:1a.0: UHCI Host Controller
    uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
    uhci_hcd 0000:00:1a.0: irq 16, io base 0x00002040
    usb usb3: configuration #1 chosen from 1 choice
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 2 ports detected
    uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    uhci_hcd 0000:00:1a.1: setting latency timer to 64
    uhci_hcd 0000:00:1a.1: UHCI Host Controller
    uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
    uhci_hcd 0000:00:1a.1: irq 17, io base 0x00002060
    usb usb4: configuration #1 chosen from 1 choice
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 2 ports detected
    uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
    uhci_hcd 0000:00:1d.0: setting latency timer to 64
    uhci_hcd 0000:00:1d.0: UHCI Host Controller
    uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
    uhci_hcd 0000:00:1d.0: irq 20, io base 0x00002080
    usb usb5: configuration #1 chosen from 1 choice
    hub 5-0:1.0: USB hub found
    hub 5-0:1.0: 2 ports detected
    alloc irq_desc for 22 on node -1
    alloc kstat_irqs on node -1
    uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 22 (level, low) -> IRQ 22
    uhci_hcd 0000:00:1d.1: setting latency timer to 64
    uhci_hcd 0000:00:1d.1: UHCI Host Controller
    uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
    uhci_hcd 0000:00:1d.1: irq 22, io base 0x000020a0
    usb usb6: configuration #1 chosen from 1 choice
    hub 6-0:1.0: USB hub found
    hub 6-0:1.0: 2 ports detected
    uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
    uhci_hcd 0000:00:1d.2: setting latency timer to 64
    uhci_hcd 0000:00:1d.2: UHCI Host Controller
    uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
    uhci_hcd 0000:00:1d.2: irq 18, io base 0x000020c0
    usb usb7: configuration #1 chosen from 1 choice
    hub 7-0:1.0: USB hub found
    hub 7-0:1.0: 2 ports detected
    kjournald starting. Commit interval 5 seconds
    EXT3-fs: mounted filesystem with writeback data mode.
    usb 2-6: new high speed USB device using ehci_hcd and address 3
    usb 2-6: configuration #1 chosen from 1 choice
    hub 2-6:1.0: USB hub found
    hub 2-6:1.0: 2 ports detected
    usb 3-1: new full speed USB device using uhci_hcd and address 2
    usb 3-1: configuration #1 chosen from 1 choice
    usb 5-2: new full speed USB device using uhci_hcd and address 2
    usb 5-2: configuration #1 chosen from 1 choice
    usb 2-6.1: new high speed USB device using ehci_hcd and address 4
    usb 2-6.1: configuration #1 chosen from 1 choice
    hub 2-6.1:1.0: USB hub found
    hub 2-6.1:1.0: 4 ports detected
    usb 2-6.2: new low speed USB device using ehci_hcd and address 5
    usb 2-6.2: configuration #1 chosen from 1 choice
    input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1d.7/usb2/2-6/2-6.2/2-6.2:1.0/input/input5
    generic-usb 0003:413C:2003.0001: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1d.7-6.2/input0
    usb 2-6.1.1: new high speed USB device using ehci_hcd and address 6
    usb 2-6.1.1: configuration #1 chosen from 1 choice
    usb 2-6.1.2: new low speed USB device using ehci_hcd and address 7
    usb 2-6.1.2: configuration #1 chosen from 1 choice
    input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1d.7/usb2/2-6/2-6.1/2-6.1.2/2-6.1.2:1.0/input/input6
    generic-usb 0003:046D:C018.0002: input,hidraw1: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1d.7-6.1.2/input0
    usb 2-6: USB disconnect, address 3
    usb 2-6.1: USB disconnect, address 4
    usb 2-6.1.1: USB disconnect, address 6
    usb 2-6.1.2: USB disconnect, address 7
    usb 2-6.2: USB disconnect, address 5
    udev: starting version 146
    sd 0:0:0:0: Attached scsi generic sg0 type 0
    sr 0:0:1:0: Attached scsi generic sg1 type 5
    sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
    Uniform CD-ROM driver Revision: 3.20
    sr 0:0:1:0: Attached scsi CD-ROM sr0
    iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
    iTCO_wdt: Found a ICH8M-E TCO device (Version=2, TCOBASE=0x1060)
    iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    ACPI: AC Adapter [C23B] (on-line)
    ACPI: Battery Slot [C23D] (battery present)
    lis3lv02d: hardware type NC2510 found.
    lis3lv02d: 12 bits sensor found
    input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d/input/input7
    Registered led device: hp::hddprotect
    lis3lv02d driver loaded.
    cfg80211: Calling CRDA to update world regulatory domain
    input: PC Speaker as /devices/platform/pcspkr/input/input8
    ACPI: WMI: Mapper loaded
    Bluetooth: Core ver 2.15
    NET: Registered protocol family 31
    Bluetooth: HCI device and connection manager initialized
    Bluetooth: HCI socket layer initialized
    thermal LNXTHERM:01: registered as thermal_zone0
    ACPI: Thermal Zone [TZ6] (25 C)
    thermal LNXTHERM:02: registered as thermal_zone1
    ACPI: Thermal Zone [TZ0] (68 C)
    thermal LNXTHERM:03: registered as thermal_zone2
    ACPI: Thermal Zone [TZ1] (69 C)
    thermal LNXTHERM:04: registered as thermal_zone3
    ACPI: Thermal Zone [TZ3] (54 C)
    thermal LNXTHERM:05: registered as thermal_zone4
    ACPI: Thermal Zone [TZ4] (29 C)
    thermal LNXTHERM:06: registered as thermal_zone5
    ACPI: Thermal Zone [TZ5] (30 C)
    alloc irq_desc for 19 on node -1
    alloc kstat_irqs on node -1
    ohci1394 0000:02:06.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
    cfg80211: World regulatory domain updated:
    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[e0101000-e01017ff] Max Packet=[2048] IR/IT contexts=[4/4]
    ACPI: SSDT 000000007f7dbcca 0023D (v01 HP Cpu0Ist 00003000 INTL 20060317)
    ACPI: SSDT 000000007f7dbf8c 005FA (v01 HP Cpu0Cst 00003001 INTL 20060317)
    Monitor-Mwait will be used to enter C-1 state
    Monitor-Mwait will be used to enter C-2 state
    Marking TSC unstable due to TSC halts in idle
    Switching to clocksource hpet
    processor LNXCPU:00: registered as cooling_device1
    ACPI: SSDT 000000007f7dbc02 000C8 (v01 HP Cpu1Ist 00003000 INTL 20060317)
    ACPI: SSDT 000000007f7dbf07 00085 (v01 HP Cpu1Cst 00003000 INTL 20060317)
    processor LNXCPU:01: registered as cooling_device2
    Bluetooth: Generic Bluetooth USB driver ver 0.6
    usbcore: registered new interface driver btusb
    ricoh-mmc: Ricoh MMC Controller disabling driver
    ricoh-mmc: Copyright(c) Philip Langdale
    ricoh-mmc: Ricoh MMC controller found at 0000:02:06.3 [1180:0843] (rev 11)
    ricoh-mmc: Controller is now disabled.
    yenta_cardbus 0000:02:06.0: CardBus bridge found [103c:30c9]
    e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2
    e1000e: Copyright (c) 1999-2008 Intel Corporation.
    e1000e 0000:00:19.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
    e1000e 0000:00:19.0: setting latency timer to 64
    alloc irq_desc for 27 on node -1
    alloc kstat_irqs on node -1
    e1000e 0000:00:19.0: irq 27 for MSI/MSI-X
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34491]
    drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [34491]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34494]
    drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 2, 12) [34495]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34495]
    drivers/input/serio/i8042.c: f6 -> i8042 (parameter) [34495]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34498]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34498]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [34498]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34500]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34500]
    drivers/input/serio/i8042.c: 0a -> i8042 (parameter) [34500]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34503]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34503]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [34503]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34506]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34506]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [34506]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34509]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34509]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [34509]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34511]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34511]
    drivers/input/serio/i8042.c: 14 -> i8042 (parameter) [34512]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34514]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34514]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [34514]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34517]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34517]
    drivers/input/serio/i8042.c: 3c -> i8042 (parameter) [34517]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34520]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34520]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [34520]
    tpm_inf_pnp 00:02: Found C284 with ID IFX0102
    tpm_inf_pnp 00:02: TPM found: config base 0x560, data base 0x570, chip version 0x000b, vendor id 0x15d1 (Infineon), product id 0x000b (SLB 9635 TT 1.2)
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34526]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34526]
    drivers/input/serio/i8042.c: 28 -> i8042 (parameter) [34526]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34529]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34529]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [34529]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34531]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34531]
    drivers/input/serio/i8042.c: 14 -> i8042 (parameter) [34532]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34534]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34534]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [34534]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34537]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34537]
    drivers/input/serio/i8042.c: 14 -> i8042 (parameter) [34537]
    yenta_cardbus 0000:02:06.0: ISA IRQ mask 0x0cb8, PCI irq 18
    yenta_cardbus 0000:02:06.0: Socket status: 30000006
    pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #03 to #06
    yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
    yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge Memory window: 0xe0100000 - 0xe03fffff
    yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge Memory window: 0x80000000 - 0x83ffffff
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34540]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34540]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [34540]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34543]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34543]
    drivers/input/serio/i8042.c: 3c -> i8042 (parameter) [34543]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34546]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34546]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [34546]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34548]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34548]
    drivers/input/serio/i8042.c: 28 -> i8042 (parameter) [34549]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34551]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34551]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [34551]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34554]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34554]
    drivers/input/serio/i8042.c: 14 -> i8042 (parameter) [34554]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34557]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34557]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [34557]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34560]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34560]
    drivers/input/serio/i8042.c: 14 -> i8042 (parameter) [34560]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34562]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34569]
    drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [34569]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34571]
    drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 2, 12) [34572]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34572]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [34572]
    b43-phy0: Broadcom 4311 WLAN found (core revision 13)
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34575]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34575]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [34575]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34578]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34578]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [34578]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34581]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34581]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [34581]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34584]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34584]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [34584]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34587]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34587]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [34587]
    b43-phy0 debug: Found PHY: Analog 4, Type 2, Revision 9
    b43-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34590]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34590]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [34590]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34592]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34592]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [34592]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34595]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34595]
    drivers/input/serio/i8042.c: e9 -> i8042 (parameter) [34595]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34598]
    drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 2, 12) [34599]
    drivers/input/serio/i8042.c: 46 <- i8042 (interrupt, 2, 12) [34601]
    drivers/input/serio/i8042.c: 12 <- i8042 (interrupt, 2, 12) [34603]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34603]
    drivers/input/serio/i8042.c: f6 -> i8042 (parameter) [34603]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34606]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34606]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [34606]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34609]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34609]
    drivers/input/serio/i8042.c: 03 -> i8042 (parameter) [34609]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34612]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34612]
    drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [34612]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34614]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34615]
    drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [34615]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34617]
    fan PNP0C0B:00: registered as cooling_device3
    ACPI: Fan [C3B1] (off)
    fan PNP0C0B:01: registered as cooling_device4
    ACPI: Fan [C3B2] (off)
    fan PNP0C0B:02: registered as cooling_device5
    ACPI: Fan [C3C8] (off)
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34619]
    fan PNP0C0B:03: registered as cooling_device6
    ACPI: Fan [C3C9] (off)
    drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [34619]
    fan PNP0C0B:04: registered as cooling_device7
    ACPI: Fan [C3CA] (off)
    fan PNP0C0B:05: registered as cooling_device8
    ACPI: Fan [C3CB] (off)
    fan PNP0C0B:06: registered as cooling_device9
    ACPI: Fan [C3CC] (off)
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34622]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34622]
    drivers/input/serio/i8042.c: e9 -> i8042 (parameter) [34622]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34625]
    drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 2, 12) [34625]
    drivers/input/serio/i8042.c: 03 <- i8042 (interrupt, 2, 12) [34627]
    drivers/input/serio/i8042.c: 64 <- i8042 (interrupt, 2, 12) [34630]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34630]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [34630]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34633]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34633]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [34633]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34635]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34635]
    drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [34635]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34638]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34638]
    drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [34638]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34641]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34641]
    drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [34641]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34644]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34644]
    drivers/input/serio/i8042.c: e9 -> i8042 (parameter) [34644]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34647]
    drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 2, 12) [34648]
    drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 2, 12) [34649]
    drivers/input/serio/i8042.c: 64 <- i8042 (interrupt, 2, 12) [34652]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34652]
    drivers/input/serio/i8042.c: e1 -> i8042 (parameter) [34652]
    drivers/input/serio/i8042.c: fe <- i8042 (interrupt, 2, 12) [34655]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34655]
    drivers/input/serio/i8042.c: f6 -> i8042 (parameter) [34655]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34657]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34657]
    drivers/input/serio/i8042.c: ff -> i8042 (parameter) [34657]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34660]
    0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:1b:24:ae:b7:02
    0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
    0000:00:19.0: eth0: MAC: 6, PHY: 6, PBA No: ffffff-0ff
    udev: renamed network interface eth0 to eth1
    phy0: Selected rate control algorithm 'pid'
    Registered led device: b43-phy0::tx
    Registered led device: b43-phy0::rx
    Registered led device: b43-phy0::radio
    Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ]
    drivers/input/serio/i8042.c: aa <- i8042 (interrupt, 2, 12) [34991]
    drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 2, 12) [34993]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34993]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [34993]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34996]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34996]
    drivers/input/serio/i8042.c: c8 -> i8042 (parameter) [34996]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [34999]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [34999]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [34999]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35002]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [35002]
    drivers/input/serio/i8042.c: 64 -> i8042 (parameter) [35002]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35005]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [35005]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35005]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35008]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [35008]
    drivers/input/serio/i8042.c: 50 -> i8042 (parameter) [35008]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35010]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [35010]
    drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [35010]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35013]
    drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 2, 12) [35015]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [35015]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35015]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35017]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [35017]
    drivers/input/serio/i8042.c: c8 -> i8042 (parameter) [35017]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35020]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [35020]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35020]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35023]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [35023]
    drivers/input/serio/i8042.c: c8 -> i8042 (parameter) [35023]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35026]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [35026]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35026]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35029]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [35029]
    drivers/input/serio/i8042.c: 50 -> i8042 (parameter) [35029]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35031]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [35031]
    drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [35031]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35034]
    drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 2, 12) [35035]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [35035]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35035]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35038]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [35038]
    drivers/input/serio/i8042.c: c8 -> i8042 (parameter) [35038]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35041]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [35041]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35041]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35044]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [35044]
    drivers/input/serio/i8042.c: 64 -> i8042 (parameter) [35044]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35047]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [35047]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35047]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35050]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [35050]
    drivers/input/serio/i8042.c: 50 -> i8042 (parameter) [35050]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35053]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [35053]
    drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [35053]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35055]
    drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 2, 12) [35057]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [35057]
    drivers/input/serio/i8042.c: ff -> i8042 (parameter) [35057]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35060]
    sdhci: Secure Digital Host Controller Interface driver
    sdhci: Copyright(c) Pierre Ossman
    ieee1394: Host added: ID:BUS[0-00:1023] GUID[001b249929bd0f10]
    drivers/input/serio/i8042.c: aa <- i8042 (interrupt, 2, 12) [35393]
    drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 2, 12) [35395]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [35395]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35395]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35398]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [35398]
    drivers/input/serio/i8042.c: 64 -> i8042 (parameter) [35398]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35400]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [35400]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35400]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35403]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [35403]
    drivers/input/serio/i8042.c: 03 -> i8042 (parameter) [35403]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35406]
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [35406]
    drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [35406]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35409]
    input: PS/2 Generic Mouse as /devices/platform/i8042/serio1/input/input9
    drivers/input/serio/i8042.c: 90 -> i8042 (command) [35409]
    drivers/input/serio/i8042.c: f4 -> i8042 (parameter) [35409]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 2, 12) [35411]
    drivers/input/serio/i8042.c: 91 -> i8042 (command) [35412]
    drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [35412]
    drivers/input/serio/i8042.c: MUX error, status is 75, data is fe [35412]
    drivers/input/serio/i8042.c: fe <- i8042 (interrupt, 3, 12, timeout) [35412]
    drivers/input/serio/i8042.c: 92 -> i8042 (command) [35412]
    drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [35412]
    drivers/input/serio/i8042.c: MUX error, status is b5, data is fe [35413]
    drivers/input/serio/i8042.c: fe <- i8042 (interrupt, 4, 12, timeout) [35413]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35413]
    drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [35413]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35416]
    drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 5, 12) [35417]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35418]
    drivers/input/serio/i8042.c: f6 -> i8042 (parameter) [35418]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35420]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35421]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35421]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35423]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35423]
    drivers/input/serio/i8042.c: 0a -> i8042 (parameter) [35423]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35427]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35427]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35427]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35430]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35430]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35430]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35433]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35433]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35433]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35435]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35435]
    drivers/input/serio/i8042.c: 14 -> i8042 (parameter) [35435]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35439]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35439]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35439]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35442]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35442]
    drivers/input/serio/i8042.c: 3c -> i8042 (parameter) [35442]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35445]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35445]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35445]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35448]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35448]
    drivers/input/serio/i8042.c: 28 -> i8042 (parameter) [35448]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35450]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35451]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35451]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35453]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35453]
    drivers/input/serio/i8042.c: 14 -> i8042 (parameter) [35453]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35456]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35456]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35456]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35459]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35459]
    drivers/input/serio/i8042.c: 14 -> i8042 (parameter) [35459]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35462]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35462]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35462]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35465]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35465]
    drivers/input/serio/i8042.c: 3c -> i8042 (parameter) [35465]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35468]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35468]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35468]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35471]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35471]
    drivers/input/serio/i8042.c: 28 -> i8042 (parameter) [35471]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35474]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35474]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35474]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35478]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35478]
    drivers/input/serio/i8042.c: 14 -> i8042 (parameter) [35478]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35480]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35481]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [35481]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35483]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35483]
    drivers/input/serio/i8042.c: 14 -> i8042 (parameter) [35483]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35486]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35486]
    drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [35486]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35489]
    drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 5, 12) [35491]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35491]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35491]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35494]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35494]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35494]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35497]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35497]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35497]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35500]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35500]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35500]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35503]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35503]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35503]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35506]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35507]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35507]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35510]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35510]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35510]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35513]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35513]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35513]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35516]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35516]
    drivers/input/serio/i8042.c: e9 -> i8042 (parameter) [35516]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35519]
    drivers/input/serio/i8042.c: 03 <- i8042 (interrupt, 5, 12) [35520]
    drivers/input/serio/i8042.c: 47 <- i8042 (interrupt, 5, 12) [35523]
    drivers/input/serio/i8042.c: 16 <- i8042 (interrupt, 5, 12) [35526]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35526]
    drivers/input/serio/i8042.c: ff -> i8042 (parameter) [35526]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35532]
    sdhci-pci 0000:02:06.2: SDHCI controller found [1180:0822] (rev 21)
    sdhci-pci 0000:02:06.2: PCI INT C -> GSI 20 (level, low) -> IRQ 20
    Registered led device: mmc0::
    mmc0: SDHCI controller on PCI [0000:02:06.2] using PIO
    HDA Intel 0000:00:1b.0: power state changed by ACPI to D0
    HDA Intel 0000:00:1b.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
    HDA Intel 0000:00:1b.0: setting latency timer to 64
    input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input10
    drivers/input/serio/i8042.c: aa <- i8042 (interrupt, 5, 12) [35894]
    drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 5, 12) [35897]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35897]
    drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [35897]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35900]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35900]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35900]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35903]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35903]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35903]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35906]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35906]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35906]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35909]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35909]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35909]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35912]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35912]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35912]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35915]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35915]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35915]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35918]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35918]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35918]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35921]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35921]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35921]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35924]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35924]
    drivers/input/serio/i8042.c: e9 -> i8042 (parameter) [35924]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35927]
    drivers/input/serio/i8042.c: 03 <- i8042 (interrupt, 5, 12) [35928]
    drivers/input/serio/i8042.c: 47 <- i8042 (interrupt, 5, 12) [35930]
    drivers/input/serio/i8042.c: 16 <- i8042 (interrupt, 5, 12) [35933]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35933]
    drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [35933]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35936]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35936]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35936]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35939]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35939]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35939]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35942]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35942]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35942]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35945]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35945]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35945]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35948]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35948]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35948]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35951]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35951]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35951]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35954]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35954]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35954]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35957]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35957]
    drivers/input/serio/i8042.c: 03 -> i8042 (parameter) [35957]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35960]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35960]
    drivers/input/serio/i8042.c: e9 -> i8042 (parameter) [35960]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35963]
    drivers/input/serio/i8042.c: 01 <- i8042 (interrupt, 5, 12) [35964]
    drivers/input/serio/i8042.c: a0 <- i8042 (interrupt, 5, 12) [35967]
    drivers/input/serio/i8042.c: b1 <- i8042 (interrupt, 5, 12) [35970]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35970]
    drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [35970]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35973]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35973]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35973]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35976]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35976]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35976]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35979]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35979]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35979]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35982]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35982]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35982]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35985]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35985]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35985]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35988]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35988]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [35988]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35991]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35991]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [35991]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35994]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35994]
    drivers/input/serio/i8042.c: 02 -> i8042 (parameter) [35994]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [35997]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [35997]
    drivers/input/serio/i8042.c: e9 -> i8042 (parameter) [35997]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36000]
    drivers/input/serio/i8042.c: a0 <- i8042 (interrupt, 5, 12) [36001]
    drivers/input/serio/i8042.c: 47 <- i8042 (interrupt, 5, 12) [36004]
    drivers/input/serio/i8042.c: 13 <- i8042 (interrupt, 5, 12) [36007]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36007]
    drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [36007]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36010]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36010]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36010]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36013]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36013]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [36013]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36016]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36016]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36016]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36019]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36019]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [36019]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36022]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36022]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36022]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36025]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36025]
    drivers/input/serio/i8042.c: 02 -> i8042 (parameter) [36025]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36028]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36028]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36028]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36031]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36031]
    drivers/input/serio/i8042.c: 01 -> i8042 (parameter) [36031]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36034]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36034]
    drivers/input/serio/i8042.c: e9 -> i8042 (parameter) [36034]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36037]
    drivers/input/serio/i8042.c: 20 <- i8042 (interrupt, 5, 12) [36039]
    drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 5, 12) [36042]
    drivers/input/serio/i8042.c: 00 <- i8042 (interrupt, 5, 12) [36045]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36045]
    drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [36045]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36048]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36048]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36048]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36051]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36051]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [36051]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36054]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36054]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36054]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36056]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36056]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [36056]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36059]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36059]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36059]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36062]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36062]
    drivers/input/serio/i8042.c: 02 -> i8042 (parameter) [36062]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36065]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36065]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36065]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36068]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36068]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [36068]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36071]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36071]
    drivers/input/serio/i8042.c: e9 -> i8042 (parameter) [36071]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36074]
    drivers/input/serio/i8042.c: 4a <- i8042 (interrupt, 5, 12) [36076]
    drivers/input/serio/i8042.c: 80 <- i8042 (interrupt, 5, 12) [36079]
    drivers/input/serio/i8042.c: a0 <- i8042 (interrupt, 5, 12) [36082]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36082]
    drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [36082]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36085]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36085]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36085]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36088]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36088]
    drivers/input/serio/i8042.c: 02 -> i8042 (parameter) [36088]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36091]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36091]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36091]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36094]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36094]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [36094]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36096]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36096]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36097]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36099]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36099]
    drivers/input/serio/i8042.c: 01 -> i8042 (parameter) [36100]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36102]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36102]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36102]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36105]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36105]
    drivers/input/serio/i8042.c: 01 -> i8042 (parameter) [36105]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36108]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36108]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [36108]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36111]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36111]
    drivers/input/serio/i8042.c: 14 -> i8042 (parameter) [36111]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36114]
    Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1a0b1, caps: 0xa04713/0x200000
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36114]
    drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [36114]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36117]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36117]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36117]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36120]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36120]
    drivers/input/serio/i8042.c: 03 -> i8042 (parameter) [36120]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36123]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36123]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36123]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36126]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36126]
    drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [36126]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36129]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36129]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36129]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36132]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36132]
    drivers/input/serio/i8042.c: 01 -> i8042 (parameter) [36132]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36135]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36135]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36135]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36138]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36138]
    drivers/input/serio/i8042.c: 01 -> i8042 (parameter) [36138]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36141]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36141]
    drivers/input/serio/i8042.c: f3 -> i8042 (parameter) [36141]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36144]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36144]
    drivers/input/serio/i8042.c: 14 -> i8042 (parameter) [36144]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36147]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36147]
    drivers/input/serio/i8042.c: e8 -> i8042 (parameter) [36147]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36150]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36150]
    drivers/input/serio/i8042.c: 03 -> i8042 (parameter) [36150]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36153]
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36153]
    drivers/input/serio/i8042.c: e6 -> i8042 (parameter) [36153]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36156]
    input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input11
    drivers/input/serio/i8042.c: 93 -> i8042 (command) [36157]
    drivers/input/serio/i8042.c: f4 -> i8042 (parameter) [36157]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 5, 12) [36160]
    input: HP WMI hotkeys as /devices/virtual/input/input12
    Non-volatile memory driver v1.3
    EXT3 FS on sda5, internal journal
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on sda7, internal journal
    EXT3-fs: mounted filesystem with writeback data mode.
    fuse init (API version 7.13)
    loop: module loaded
    Adding 2401676k swap on /dev/sda6. Priority:-1 extents:1 across:2401676k
    microcode: CPU0 sig=0x6fd, pf=0x80, revision=0xa3
    platform microcode: firmware: requesting intel-ucode/06-0f-0d
    drivers/input/serio/i8042.c: ed -> i8042 (kbd-data) [43419]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [43420]
    drivers/input/serio/i8042.c: 02 -> i8042 (kbd-data) [43420]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [43423]
    microcode: CPU1 sig=0x6fd, pf=0x80, revision=0xa3
    platform microcode: firmware: requesting intel-ucode/06-0f-0d
    Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
    NET: Registered protocol family 10
    lo: Disabled Privacy Extensions
    cfg80211: Calling CRDA for country: NL
    cfg80211: Regulatory domain changed to country: NL
    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
    (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
    (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
    (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
    e1000e 0000:00:19.0: irq 27 for MSI/MSI-X
    e1000e 0000:00:19.0: irq 27 for MSI/MSI-X
    ADDRCONF(NETDEV_UP): eth1: link is not ready
    b43 ssb0:0: firmware: requesting b43/ucode13.fw
    b43 ssb0:0: firmware: requesting b43/b0g0initvals13.fw
    b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
    b43-phy0 debug: Chip initialized
    b43-phy0 debug: 64-bit DMA initialized
    b43-phy0 debug: QoS enabled
    b43-phy0 debug: Wireless interface started
    b43-phy0 debug: Adding Interface type 2
    ADDRCONF(NETDEV_UP): wlan0: link is not ready
    e1000e: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
    0000:00:19.0: eth1: 10/100 speed: disabling TSO
    ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
    NET: Registered protocol family 17
    wlan0: deauthenticating from 00:1b:90:76:d3:f0 by local choice (reason=3)
    wlan0: direct probe to AP 00:1b:90:76:d3:f0 (try 1)
    wlan0: direct probe responded
    wlan0: authenticate with AP 00:1b:90:76:d3:f0 (try 1)
    wlan0: authenticated
    wlan0: associate with AP 00:1b:90:76:d3:f0 (try 1)
    wlan0: RX AssocResp from 00:1b:90:76:d3:f0 (capab=0x431 status=0 aid=142)
    wlan0: associated
    ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
    cfg80211: Calling CRDA for country: NL
    wlan0: deauthenticating from 00:1b:90:76:d3:f0 by local choice (reason=3)
    wlan0: deauthenticating from 00:1b:90:76:d3:f0 by local choice (reason=3)
    cfg80211: Current regulatory domain updated by AP to: NL
    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
    PPP generic driver version 2.4.2
    NET: Registered protocol family 24
    drivers/input/serio/i8042.c: ed -> i8042 (kbd-data) [52092]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [52093]
    drivers/input/serio/i8042.c: 00 -> i8042 (kbd-data) [52093]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [52096]
    drivers/input/serio/i8042.c: ed -> i8042 (kbd-data) [52267]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [52267]
    drivers/input/serio/i8042.c: 02 -> i8042 (kbd-data) [52267]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [52270]
    eth1: no IPv6 routers present
    wlan0: no IPv6 routers present
    CPUFREQ: Per core ondemand sysfs interface is deprecated - ignore_nice_load
    drivers/input/serio/i8042.c: ed -> i8042 (kbd-data) [827841]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [827842]
    drivers/input/serio/i8042.c: 03 -> i8042 (kbd-data) [827842]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [827844]
    drivers/input/serio/i8042.c: ed -> i8042 (kbd-data) [3600107]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [3600107]
    drivers/input/serio/i8042.c: 02 -> i8042 (kbd-data) [3600107]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [3600110]
    drivers/input/serio/i8042.c: ed -> i8042 (kbd-data) [3660206]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [3660207]
    drivers/input/serio/i8042.c: 03 -> i8042 (kbd-data) [3660207]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [3660209]
    drivers/input/serio/i8042.c: ed -> i8042 (kbd-data) [3900629]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [3900630]
    drivers/input/serio/i8042.c: 02 -> i8042 (kbd-data) [3900630]
    drivers/input/serio/i8042.c: fa <- i8042 (interrupt, 0, 1) [3900633]
    \
     
     \ /
      Last update: 2009-10-15 21:37    [W:0.150 / U:89.148 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site