Messages in this thread | | | Date | Thu, 11 Sep 2008 18:06:28 -0600 | From | Robert Hancock <> | Subject | Re: Hard drive not seen by mount when booting using busybox/initrd under 2.6.27-2-generic (Ubuntu) |
| |
Miles Lane wrote: > I get the messages below during the setup of the drives on my machine. > Is the kernel failing to set up my drives correctly? One clue is > that it looks as though perhaps BOTH pata_acpi and ata_piix are trying > to handle the hard drives interface??? I am also puzzled by the line > "sda:<6>ata5.00: ATAPI: Optiarc DVD RW AD-7530A", which seems to > indicate that sda is somehow getting confused with my DVD-RW drive.
That's just two kernel messages stomping on top of each other.
> > I get a similar problem when I compile and test a 2.6.27-rc6 kernel. > The only difference is that I also see a message saying that my > modules cannot be found before the mount error occurs. > > I tried mounting partitions from my drive from the command line and > all attempts gave the same error: "device not found".
There doesn't seem like there's anything wrong here, the /dev/sda device should be available. Unless there's some kind of udev problem or something that's screwing up the device nodes..
> > [ 4.459717] ata1: SATA max UDMA/133 abar m1024@0xd8444400 port > 0xd8444500 irq 2301 > [ 4.459720] ata2: DUMMY > [ 4.459723] ata3: SATA max UDMA/133 abar m1024@0xd8444400 port > 0xd8444600 irq 2301 > [ 4.459726] ata4: DUMMY > [ 5.056152] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) > [ 5.057177] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out > [ 5.057342] ata1.00: ATA-7: Hitachi HTS541616J9SA00, SB4OC70P, max UDMA/100 > [ 5.057345] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32) > [ 5.058519] ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out > [ 5.058686] ata1.00: configured for UDMA/100 > [ 5.392129] ata3: SATA link down (SStatus 0 SControl 300) > [ 5.408396] scsi 0:0:0:0: Direct-Access ATA Hitachi > HTS54161 SB4O PQ: 0 ANSI: 5 > [ 5.464760] pata_acpi 0000:00:1f.1: PCI INT B -> GSI 19 (level, > low) -> IRQ 19 > [ 5.464798] pata_acpi 0000:00:1f.1: setting latency timer to 64 > [ 5.464821] pata_acpi 0000:00:1f.1: PCI INT B disabled > [ 5.468055] ata_piix 0000:00:1f.1: version 2.12 > [ 5.468065] ata_piix 0000:00:1f.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 > [ 5.468109] ata_piix 0000:00:1f.1: setting latency timer to 64 > [ 5.468195] scsi4 : ata_piix > [ 5.468273] scsi5 : ata_piix > [ 5.469015] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1810 irq 14 > [ 5.469019] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15 > [ 5.478018] Driver 'sd' needs updating - please use bus_type methods > [ 5.478163] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) > [ 5.478192] sd 0:0:0:0: [sda] Write Protect is off > [ 5.478195] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 > [ 5.478240] sd 0:0:0:0: [sda] Write cache: enabled, read cache: > enabled, doesn't support DPO or FUA > [ 5.478344] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) > [ 5.478369] sd 0:0:0:0: [sda] Write Protect is off > [ 5.478372] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 > [ 5.478418] sd 0:0:0:0: [sda] Write cache: enabled, read cache: > enabled, doesn't support DPO or FUA > [ 5.478423] sda:<6>ata5.00: ATAPI: Optiarc DVD RW AD-7530A, EX32, > max UDMA/33 > [ 5.648451] ata5.00: configured for UDMA/33 > [ 5.648503] ata6: port disabled. ignoring. > [ 5.648548] isa bounce pool size: 16 pages > [ 5.649976] scsi 4:0:0:0: CD-ROM Optiarc DVD RW > AD-7530A EX32 PQ: 0 ANSI: 5 > [ 5.661100] Driver 'sr' needs updating - please use bus_type methods > [ 5.879315] sda1 sda2 > [ 5.879493] sd 0:0:0:0: [sda] Attached SCSI disk > [ 5.886208] sd 0:0:0:0: Attached scsi generic sg0 type 0 > [ 5.886253] sr 4:0:0:0: Attached scsi generic sg1 type 5 > [ 5.894719] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw > xa/form2 cdda tray > [ 5.894725] Uniform CD-ROM driver Revision: 3.20 > [ 5.894830] sr 4:0:0:0: Attached scsi CD-ROM sr0
| |