lkml.org 
[lkml]   [2008]   [Aug]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [regression] usb: sometimes dead keyboard after boot
Date
On Saturday 30 August 2008, Alan Stern wrote:
> On Fri, 29 Aug 2008, Alan Stern wrote:
> > > Does this sound at all logical and feasible?
> >
> > The first proposal is feasible; I can write a patch to implement it.
> > How much it will end up helping anything isn't clear, though.
>
> Here's the promised patch. Be warned, I haven't tested it at all.

The patch seems to do exactly what I was looking for! Details further
down, but first some other comments.


My first boot with your patch was with brltty still enabled. The log
showed the right result, but I wanted to get a cleaner log without all
the USB suspend/resume noise caused by brltty. So I disabled brltty's
init script and rebooted.

This gave a totally unexpected result: ehci now got loaded and initialized
_before_ uhci which of course avoids the problem altogether (see attached
log: dmesg_ehci-first). So apparently brltty's init script was
responsible not only for the suspend/resume noise, but also influenced
the load order of the two USB drivers.
And apparently when things are left alone ehci _will_ be loaded before
uhci, but that does not match what you described in earlier mails as it
means the PCI bus order isn't followed. Confusing...


Anyway, this meant that to test your patch I had to try to get uhci to
load first again. This turned out to be simple: just adding uhci_hcd
in /etc/modules did the trick. The result is in dmesg_uhci-first.

That log shows what was desired, at least 3-1 and 4-1 get disconnected
cleanly and I get no error messages to the console. Yay!

I added two extra printk's around the usb_wait_for_khubd_idle call to show
the exact effect of the wait (look for "khubd_idle" in two messages).
These seem to show what was wanted: both keyboard and mouse are detected
during the wait.

But it also shows a few events on bus 3 and 4 that happen after I get
khubd_idle that seem to indicate the probe on that bus is not completely
finished and that could maybe still cause "problems". But maybe I'm just
reading it wrong and those events are part of the lead up to the
disconnects for the hand-off.

Anyway, I'm quite happy with the result, so:
Tested-by: Frans Pop <elendil@planet.nl>


Last note FYI. I had another case of "dead keyboard" this morning, again
with the "reset low speed USB device" message in the log. Unfortunately
this was before I enabled USB debugging (and obviously before I had
applied the patch).
I will now revert the patch and keep USB debugging enabled to see if I can
catch this bug properly. I'll send the debug log when I do.

Cheers,
FJP

Linux version 2.6.27-rc5-usb (root@faramir) (gcc version 4.3.1 (Debian 4.3.1-9) ) #67 SMP Sat Aug 30 12:25:07 CEST 2008
Command line: root=/dev/mapper/main-root ro vga=791 quiet
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007f674000 (usable)
BIOS-e820: 000000007f674000 - 000000007f6e9000 (ACPI NVS)
BIOS-e820: 000000007f6e9000 - 000000007f6ec000 (usable)
BIOS-e820: 000000007f6ec000 - 000000007f6ff000 (ACPI data)
BIOS-e820: 000000007f6ff000 - 000000007f700000 (usable)
last_pfn = 0x7f700 max_arch_pfn = 0x3ffffffff
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
init_memory_mapping
0000000000 - 007f600000 page 2M
007f600000 - 007f700000 page 4k
kernel direct mapping tables up to 7f700000 @ 8000-c000
last_map_addr: 7f700000 end: 7f700000
RAMDISK: 37d18000 - 37fefa45
DMI 2.3 present.
ACPI: RSDP 000FE020, 0014 (r0 INTEL )
ACPI: RSDT 7F6FDE48, 0058 (r1 INTEL D945GCZ FF9 MSFT 1000013)
ACPI: FACP 7F6FCF10, 0074 (r1 INTEL D945GCZ FF9 MSFT 1000013)
ACPI: DSDT 7F6F7010, 4348 (r1 INTEL D945GCZ FF9 MSFT 1000013)
ACPI: FACS 7F6E2C40, 0040
ACPI: APIC 7F6FCE10, 0078 (r1 INTEL D945GCZ FF9 MSFT 1000013)
ACPI: WDDT 7F6F6F90, 0040 (r1 INTEL D945GCZ FF9 MSFT 1000013)
ACPI: MCFG 7F6F6F10, 003C (r1 INTEL D945GCZ FF9 MSFT 1000013)
ACPI: ASF! 7F6FCD10, 00A6 (r32 INTEL D945GCZ FF9 MSFT 1000013)
ACPI: HPET 7F6F6E90, 0038 (r1 INTEL D945GCZ FF9 MSFT 1000013)
ACPI: SSDT 7F6FDC10, 01BC (r1 INTEL CpuPm FF9 MSFT 1000013)
ACPI: SSDT 7F6FDA10, 0175 (r1 INTEL Cpu0Ist FF9 MSFT 1000013)
ACPI: SSDT 7F6FD810, 0175 (r1 INTEL Cpu1Ist FF9 MSFT 1000013)
ACPI: SSDT 7F6FD610, 0175 (r1 INTEL Cpu2Ist FF9 MSFT 1000013)
ACPI: SSDT 7F6FD410, 0175 (r1 INTEL Cpu3Ist FF9 MSFT 1000013)
ACPI: SSDT 7F6F6E10, 002F (r1 INTEL SetupVar FF9 MSFT 1000013)
ACPI: TCPA 7F6E4D90, 0032 (r1 INTEL TIANO 2 MSFT 1000013)
No NUMA configuration found
Faking a node at 0000000000000000-000000007f700000
Bootmem setup node 0 0000000000000000-000000007f700000
NODE_DATA [0000000000001000 - 0000000000004fff]
bootmap [000000000000a000 - 0000000000019edf] pages 10
(6 early reservations) ==> bootmem [0000000000 - 007f700000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
#2 [0000200000 - 000074e4e0] TEXT DATA BSS ==> [0000200000 - 000074e4e0]
#3 [0037d18000 - 0037fefa45] RAMDISK ==> [0037d18000 - 0037fefa45]
#4 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
#5 [0000008000 - 000000a000] PGTABLE ==> [0000008000 - 000000a000]
found SMP MP-table at [ffff8800000fe680] 000fe680
[ffffe20000000000-ffffe20001ffffff] PMD -> [ffff880001200000-ffff8800031fffff] on node 0
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x00100000
Movable zone start PFN for each node
early_node_map[4] active PFN ranges
0: 0x00000000 -> 0x0000009f
0: 0x00000100 -> 0x0007f674
0: 0x0007f6e9 -> 0x0007f6ec
0: 0x0007f6ff -> 0x0007f700
On node 0 totalpages: 521751
DMA zone: 2474 pages, LIFO batch:0
DMA32 zone: 509660 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 0, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 4 CPUs, 2 hotplug CPUs
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
PM: Registered nosave memory: 000000007f674000 - 000000007f6e9000
PM: Registered nosave memory: 000000007f6ec000 - 000000007f6ff000
Allocating PCI resources starting at 80000000 (gap: 7f700000:80900000)
PERCPU: Allocating 47648 bytes of per cpu data
NR_CPUS: 8, nr_cpu_ids: 4, nr_node_ids 1
Built 1 zonelists in Node order, mobility grouping on. Total pages: 512134
Policy zone: DMA32
Kernel command line: root=/dev/mapper/main-root ro vga=791 quiet
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
TSC calibrated against PM_TIMER
Detected 3199.880 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Checking aperture...
No AGP bridge found
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
Memory: 2045500k/2087936k available (2287k kernel code, 41504k reserved, 1438k data, 368k init)
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
hpet clockevent registered
Calibrating delay loop (skipped), value calculated using timer frequency.. 6399.76 BogoMIPS (lpj=12799520)
Security Framework initialized
SELinux: Disabled at boot.
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Mount-cache hash table entries: 256
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU 0/0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM1)
using mwait in idle threads.
ACPI: Core revision 20080609
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Pentium(R) D CPU 3.20GHz stepping 07
Using local APIC timer interrupts.
APIC timer calibration result 12499526
Detected 12.499 MHz APIC timer.
Booting processor 1/1 ip 6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 6399.92 BogoMIPS (lpj=12799859)
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM1)
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: Intel(R) Pentium(R) D CPU 3.20GHz stepping 07
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (12799.68 BogoMIPS).
CPU0 attaching sched-domain:
domain 0: span 0-1 level CPU
groups: 0 1
domain 1: span 0-1 level NODE
groups: 0-1
CPU1 attaching sched-domain:
domain 0: span 0-1 level CPU
groups: 1 0
domain 1: span 0-1 level NODE
groups: 0-1
net_namespace: 1552 bytes
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Found Intel Corporation 945G/GZ/P/PL Express Memory Controller Hub without MMCONFIG support.
PCI: Using configuration type 1 for base access
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.2: PME# disabled
pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.3: PME# disabled
pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.4: PME# disabled
pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.5: PME# disabled
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
pci 0000:01:00.0: PME# disabled
pci 0000:01:00.3: PME# supported from D0 D3hot D3cold
pci 0000:01:00.3: PME# disabled
pci 0000:01:00.4: PME# supported from D0 D3hot D3cold
pci 0000:01:00.4: PME# disabled
PCI: bridge 0000:00:1c.0 io port: [1000, 1fff]
PCI: bridge 0000:00:1c.0 32bit mmio: [90000000, 901fffff]
PCI: bridge 0000:00:1c.2 32bit mmio: [90300000, 903fffff]
PCI: bridge 0000:00:1c.3 32bit mmio: [90400000, 904fffff]
PCI: bridge 0000:00:1c.4 32bit mmio: [90500000, 905fffff]
PCI: bridge 0000:00:1c.5 32bit mmio: [90600000, 906fffff]
pci 0000:00:1e.0: transparent bridge
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX5._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 *10 11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 *9 10 11 12)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 *9 10 11 12)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:00: parse allocated resources
pnp 00:00: add io 0xcf8-0xcff flags 0x1
pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
pnp 00:01: parse allocated resources
pnp 00:01: add mem 0xf0000000-0xf3ffffff flags 0x0
pnp 00:01: add mem 0xfed13000-0xfed13fff flags 0x0
pnp 00:01: add mem 0xfed14000-0xfed17fff flags 0x0
pnp 00:01: add mem 0xfed18000-0xfed18fff flags 0x0
pnp 00:01: add mem 0xfed19000-0xfed19fff flags 0x0
pnp 00:01: add mem 0xfed1c000-0xfed1ffff flags 0x0
pnp 00:01: add mem 0xfed20000-0xfed3ffff flags 0x0
pnp 00:01: add mem 0xfed45000-0xfed99fff flags 0x0
pnp 00:01: add mem 0xc0000-0xdffff flags 0x0
pnp 00:01: add mem 0xe0000-0xfffff flags 0x0
pnp 00:01: PNP0c02: calling quirk_system_pci_resources+0x0/0x179
pnp 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:02: parse allocated resources
pnp 00:02: add io 0x0-0xf flags 0x1
pnp 00:02: add io 0x81-0x83 flags 0x1
pnp 00:02: add io 0x87-0x87 flags 0x1
pnp 00:02: add io 0x89-0x8b flags 0x1
pnp 00:02: add io 0x8f-0x8f flags 0x1
pnp 00:02: add io 0xc0-0xdf flags 0x1
pnp 00:02: add dma 4 flags 0x0
pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
pnp 00:03: parse allocated resources
pnp 00:03: add io 0x70-0x71 flags 0x1
pnp 00:03: add io 0x74-0x77 flags 0x1
pnp 00:03: add irq 8 flags 0x1
pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
pnp 00:04: parse allocated resources
pnp 00:04: add io 0xf0-0xf0 flags 0x1
pnp 00:04: add irq 13 flags 0x1
pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
pnp 00:05: parse allocated resources
pnp 00:05: add io 0x61-0x61 flags 0x1
pnp 00:05: Plug and Play ACPI device, IDs PNP0800 (active)
pnp 00:06: parse allocated resources
pnp 00:06: add io 0x500-0x53f flags 0x1
pnp 00:06: add io 0x400-0x47f flags 0x1
pnp 00:06: add io 0x92-0x92 flags 0x1
pnp 00:06: add io 0x680-0x6ff flags 0x1
pnp 00:06: add io 0x10-0x1f flags 0x1
pnp 00:06: add io 0x72-0x73 flags 0x1
pnp 00:06: add io 0x80-0x80 flags 0x1
pnp 00:06: add io 0x84-0x86 flags 0x1
pnp 00:06: add io 0x88-0x88 flags 0x1
pnp 00:06: add io 0x8c-0x8e flags 0x1
pnp 00:06: add io 0x90-0x9f flags 0x1
pnp 00:06: PNP0c02: calling quirk_system_pci_resources+0x0/0x179
pnp 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:07: parse allocated resources
pnp 00:07: add mem 0xfed40000-0xfed44fff flags 0x0
pnp 00:07: PNP0c02: calling quirk_system_pci_resources+0x0/0x179
pnp 00:07: Plug and Play ACPI device, IDs PNP0c31 PNP0c02 (active)
pnp 00:08: parse allocated resources
pnp 00:08: add io 0x60-0x60 flags 0x1
pnp 00:08: add io 0x64-0x64 flags 0x1
pnp 00:08: PNP0c02: calling quirk_system_pci_resources+0x0/0x179
pnp 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:09: parse allocated resources
pnp 00:09: add io 0x3f0-0x3f5 flags 0x1
pnp 00:09: add io 0x3f0-0x3f0 flags 0x1
pnp 00:09: add irq 6 flags 0x1
pnp 00:09: add dma 2 flags 0x0
pnp 00:09: parse resource options
pnp 00:09: dependent set 0 (preferred) io min 0x3f0 max 0x3f0 align 1 size 6 flags 0x1
pnp 00:09: dependent set 0 (preferred) io min 0x3f7 max 0x3f7 align 1 size 1 flags 0x1
pnp 00:09: dependent set 0 (preferred) irq 6 flags 0x1
pnp 00:09: dependent set 0 (preferred) dma 2 (bitmask 0x4) flags 0x0
pnp 00:09: Plug and Play ACPI device, IDs PNP0700 (active)
pnp 00:0a: parse allocated resources
pnp 00:0a: add io 0x378-0x37f flags 0x1
pnp 00:0a: add io 0x778-0x77f flags 0x1
pnp 00:0a: add irq 7 flags 0x1
pnp 00:0a: add dma 0 flags 0x10000000
pnp 00:0a: parse resource options
pnp 00:0a: dependent set 0 (preferred) io min 0x378 max 0x378 align 1 size 8 flags 0x1
pnp 00:0a: dependent set 0 (preferred) io min 0x778 max 0x778 align 1 size 8 flags 0x1
pnp 00:0a: dependent set 0 (preferred) irq 5 7 flags 0x1
pnp 00:0a: dependent set 0 (preferred) dma 1 3 (bitmask 0xa) flags 0x0
pnp 00:0a: dependent set 1 (preferred) io min 0x278 max 0x278 align 1 size 8 flags 0x1
pnp 00:0a: dependent set 1 (preferred) io min 0x678 max 0x678 align 1 size 8 flags 0x1
pnp 00:0a: dependent set 1 (preferred) irq 5 7 flags 0x1
pnp 00:0a: dependent set 1 (preferred) dma 1 3 (bitmask 0xa) flags 0x0
pnp 00:0a: dependent set 2 (preferred) io min 0x3bc max 0x3bc align 1 size 4 flags 0x1
pnp 00:0a: dependent set 2 (preferred) io min 0x7bc max 0x7bc align 1 size 4 flags 0x1
pnp 00:0a: dependent set 2 (preferred) irq 5 7 flags 0x1
pnp 00:0a: dependent set 2 (preferred) dma 1 3 (bitmask 0xa) flags 0x0
pnp 00:0a: Plug and Play ACPI device, IDs PNP0401 (active)
pnp 00:0b: parse allocated resources
pnp 00:0b: add io 0x3f8-0x3ff flags 0x1
pnp 00:0b: add irq 4 flags 0x1
pnp 00:0b: parse resource options
pnp 00:0b: dependent set 0 (preferred) io min 0x3f8 max 0x3f8 align 1 size 8 flags 0x1
pnp 00:0b: dependent set 0 (preferred) irq 4 flags 0x1
pnp 00:0b: dependent set 1 (preferred) io min 0x3e8 max 0x3e8 align 1 size 8 flags 0x1
pnp 00:0b: dependent set 1 (preferred) irq 4 flags 0x1
pnp 00:0b: dependent set 2 (preferred) io min 0x2f8 max 0x2f8 align 1 size 8 flags 0x1
pnp 00:0b: dependent set 2 (preferred) irq 3 flags 0x1
pnp 00:0b: dependent set 3 (preferred) io min 0x2e8 max 0x2e8 align 1 size 8 flags 0x1
pnp 00:0b: dependent set 3 (preferred) irq 3 flags 0x1
pnp 00:0b: dependent set 4 (functional) io min 0x100 max 0x3f8 align 8 size 8 flags 0x1
pnp 00:0b: dependent set 4 (functional) irq 1 3 4 5 6 7 8 10 11 12 13 14 15 flags 0x1
pnp 00:0b: Plug and Play ACPI device, IDs PNP0501 (active)
pnp 00:0c: parse allocated resources
pnp 00:0c: add mem 0xfec00000-0xfec000ff flags 0x0
pnp 00:0c: Plug and Play ACPI device, IDs PNP0003 (active)
pnp 00:0d: parse allocated resources
pnp 00:0d: add mem 0xfed00000-0xfed003ff flags 0x0
pnp 00:0d: Plug and Play ACPI device, IDs PNP0103 (active)
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI-GART: No AMD northbridge found.
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
ACPI: RTC can wake from S4
pnp: the driver 'system' has been registered
system 00:01: iomem range 0xf0000000-0xf3ffffff has been reserved
system 00:01: iomem range 0xfed13000-0xfed13fff has been reserved
system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved
system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved
system 00:01: iomem range 0xfed20000-0xfed3ffff has been reserved
system 00:01: iomem range 0xfed45000-0xfed99fff has been reserved
system 00:01: iomem range 0xc0000-0xdffff has been reserved
system 00:01: iomem range 0xe0000-0xfffff could not be reserved
system 00:01: driver attached
system 00:06: ioport range 0x500-0x53f has been reserved
system 00:06: ioport range 0x400-0x47f has been reserved
system 00:06: ioport range 0x680-0x6ff has been reserved
system 00:06: driver attached
system 00:07: iomem range 0xfed40000-0xfed44fff has been reserved
system 00:07: driver attached
system 00:08: driver attached
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:01
pci 0000:00:1c.0: IO window: 0x1000-0x1fff
pci 0000:00:1c.0: MEM window: 0x90000000-0x901fffff
pci 0000:00:1c.0: PREFETCH window: disabled
pci 0000:00:1c.2: PCI bridge, secondary bus 0000:02
pci 0000:00:1c.2: IO window: disabled
pci 0000:00:1c.2: MEM window: 0x90300000-0x903fffff
pci 0000:00:1c.2: PREFETCH window: disabled
pci 0000:00:1c.3: PCI bridge, secondary bus 0000:03
pci 0000:00:1c.3: IO window: disabled
pci 0000:00:1c.3: MEM window: 0x90400000-0x904fffff
pci 0000:00:1c.3: PREFETCH window: disabled
pci 0000:00:1c.4: PCI bridge, secondary bus 0000:04
pci 0000:00:1c.4: IO window: disabled
pci 0000:00:1c.4: MEM window: 0x90500000-0x905fffff
pci 0000:00:1c.4: PREFETCH window: disabled
pci 0000:00:1c.5: PCI bridge, secondary bus 0000:05
pci 0000:00:1c.5: IO window: disabled
pci 0000:00:1c.5: MEM window: 0x90600000-0x906fffff
pci 0000:00:1c.5: PREFETCH window: disabled
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:06
pci 0000:00:1e.0: IO window: disabled
pci 0000:00:1e.0: MEM window: disabled
pci 0000:00:1e.0: PREFETCH window: disabled
pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
pci 0000:00:1c.2: setting latency timer to 64
pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
pci 0000:00:1c.3: setting latency timer to 64
pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.4: setting latency timer to 64
pci 0000:00:1c.5: PCI INT B -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.5: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [0, ffffffffffffffff]
bus: 01 index 0 io port: [1000, 1fff]
bus: 01 index 1 mmio: [90000000, 901fffff]
bus: 01 index 2 mmio: [0, 0]
bus: 01 index 3 mmio: [0, 0]
bus: 02 index 0 mmio: [0, 0]
bus: 02 index 1 mmio: [90300000, 903fffff]
bus: 02 index 2 mmio: [0, 0]
bus: 02 index 3 mmio: [0, 0]
bus: 03 index 0 mmio: [0, 0]
bus: 03 index 1 mmio: [90400000, 904fffff]
bus: 03 index 2 mmio: [0, 0]
bus: 03 index 3 mmio: [0, 0]
bus: 04 index 0 mmio: [0, 0]
bus: 04 index 1 mmio: [90500000, 905fffff]
bus: 04 index 2 mmio: [0, 0]
bus: 04 index 3 mmio: [0, 0]
bus: 05 index 0 mmio: [0, 0]
bus: 05 index 1 mmio: [90600000, 906fffff]
bus: 05 index 2 mmio: [0, 0]
bus: 05 index 3 mmio: [0, 0]
bus: 06 index 0 mmio: [0, 0]
bus: 06 index 1 mmio: [0, 0]
bus: 06 index 2 mmio: [0, 0]
bus: 06 index 3 io port: [0, ffff]
bus: 06 index 4 mmio: [0, ffffffffffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 9, 2097152 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
NET: Registered protocol family 1
checking if image is initramfs... it is
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
Freeing initrd memory: 2910k freed
audit: initializing netlink socket (disabled)
type=2000 audit(1220094455.516:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
msgmni has been set to 4000
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:02.0: Boot video device
pci 0000:00:1d.0: uhci_check_and_reset_hc: legsup = 0x0f10
pci 0000:00:1d.0: Performing full reset
pci 0000:00:1d.1: uhci_check_and_reset_hc: legsup = 0x0010
pci 0000:00:1d.1: Performing full reset
pci 0000:00:1d.2: uhci_check_and_reset_hc: legsup = 0x0010
pci 0000:00:1d.2: Performing full reset
pci 0000:00:1d.3: uhci_check_and_reset_hc: legsup = 0x0010
pci 0000:00:1d.3: Performing full reset
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.0: found MSI capability
pci_express 0000:00:1c.0:pcie00: allocate port service
pci_express 0000:00:1c.0:pcie02: allocate port service
pcieport-driver 0000:00:1c.2: setting latency timer to 64
pcieport-driver 0000:00:1c.2: found MSI capability
pci_express 0000:00:1c.2:pcie00: allocate port service
pci_express 0000:00:1c.2:pcie02: allocate port service
pcieport-driver 0000:00:1c.3: setting latency timer to 64
pcieport-driver 0000:00:1c.3: found MSI capability
pci_express 0000:00:1c.3:pcie00: allocate port service
pci_express 0000:00:1c.3:pcie02: allocate port service
pcieport-driver 0000:00:1c.4: setting latency timer to 64
pcieport-driver 0000:00:1c.4: found MSI capability
pci_express 0000:00:1c.4:pcie00: allocate port service
pci_express 0000:00:1c.4:pcie02: allocate port service
pcieport-driver 0000:00:1c.5: setting latency timer to 64
pcieport-driver 0000:00:1c.5: found MSI capability
pci_express 0000:00:1c.5:pcie00: allocate port service
pci_express 0000:00:1c.5:pcie02: allocate port service
vesafb: framebuffer at 0x80000000, mapped to 0xffffc20000a00000, using 3072k, total 7872k
vesafb: mode is 1024x768x16, linelength=2048, pages=4
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
hpet_resources: 0xfed00000 is busy
Linux agpgart interface v0.103
Serial: 8250/16550 driver4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
pnp: the driver 'serial' has been registered
00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial 00:0b: driver attached
serial 0000:01:00.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18
0000:01:00.3: ttyS1 at I/O 0x1020 (irq = 18) is a 16550A
brd: module loaded
pnp: the driver 'i8042 kbd' has been registered
pnp: the driver 'i8042 aux' has been registered
pnp: the driver 'i8042 kbd' has been unregistered
pnp: the driver 'i8042 aux' has been unregistered
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
pnp: the driver 'rtc_cmos' has been registered
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, hpet irqs
rtc_cmos 00:03: driver attached
cpuidle: using governor ladder
cpuidle: using governor menu
TCP bic registered
NET: Registered protocol family 17
rtc_cmos 00:03: setting system clock to 2008-08-30 11:07:36 UTC (1220094456)
Freeing unused kernel memory: 368k freed
No dock devices found.
SCSI subsystem initialized
libata version 3.00 loaded.
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m1024@0x902c4000 port 0x902c4100 irq 506
ata2: SATA max UDMA/133 abar m1024@0x902c4000 port 0x902c4180 irq 506
ata3: SATA max UDMA/133 abar m1024@0x902c4000 port 0x902c4200 irq 506
ata4: SATA max UDMA/133 abar m1024@0x902c4000 port 0x902c4280 irq 506
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: HDT722516DLA380, V43OA96A, max UDMA/133
ata1.00: 321672960 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATAPI: Optiarc DVD RW AD-7170S, 1.00, max UDMA/66
ata3.00: configured for UDMA/66
ata4: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access ATA HDT722516DLA380 V43O PQ: 0 ANSI: 5
scsi 2:0:0:0: CD-ROM Optiarc DVD RW AD-7170S 1.00 PQ: 0 ANSI: 5
processor ACPI0007:00: registered as cooling_device0
processor ACPI0007:01: registered as cooling_device1
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:0:0: [sda] 321672960 512-byte hardware sectors (164697 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 321672960 512-byte hardware sectors (164697 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 < sda5 sda6 > sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
udevd version 125 started
Floppy drive(s): fd0 is 1.44M
input: PC Speaker as /class/input/input0
FDC 0 is a post-1991 82077
ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: reset hcs_params 0x104208 dbg=1 cc=4 pcc=2 ordered !ppc ports=8
ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7 uframes 1024 64 bit addr
ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 128 is not supported
ehci_hcd 0000:00:1d.7: supports USB remote wakeup
ehci_hcd 0000:00:1d.7: irq 23, io mem 0x902c4400
ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:1d.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: default language 0x0409
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: trying to enable port power on non-switchable hub
USB Universal Host Controller Interface driver v3.0
e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k2
e1000e: Copyright (c) 1999-2008 Intel Corporation.
input: Power Button (FF) as /class/input/input1
ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 5: status 0501 change 0001
ehci_hcd 0000:00:1d.7: GetStatus port 7 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 7: status 0501 change 0001
ACPI: Power Button (FF) [PWRF]
input: Sleep Button (CM) as /class/input/input2
pnp: the driver 'parport_pc' has been registered
parport_pc 00:0a: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
ACPI: Sleep Button (CM) [SLPB]
Uniform Multi-Platform E-IDE driver
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0460)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
hub 1-0:1.0: state 7 ports 8 chg 00a0 evt 0000
drivers/usb/core/inode.c: creating file '001'
hub 1-0:1.0: port 5, status 0501, change 0000, 480 Mb/s
ehci_hcd 0000:00:1d.7: port 5 low speed --> companion
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.27-rc5-usb ehci_hcd
usb usb1: SerialNumber: 0000:00:1d.7
agpgart-intel 0000:00:00.0: Intel 945G Chipset
agpgart-intel 0000:00:00.0: detected 7932K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0x80000000
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
drivers/usb/core/inode.c: creating file '002'
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: detected 2 ports
uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:1d.0: Performing full reset
uhci_hcd 0000:00:1d.0: supports USB remote wakeup
uhci_hcd 0000:00:1d.0: irq 23, io base 0x00002080
usb usb2: default language 0x0409
usb usb2: uevent
usb usb2: usb_probe_device
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: trying to enable port power on non-switchable hub
parport0: Printer, HEWLETT-PACKARD PHOTOSMART P1100
parport_pc 00:0a: driver attached
Driver 'sr' needs updating - please use bus_type methods
ehci_hcd 0000:00:1d.7: GetStatus port 5 status 003002 POWER OWNER sig=se0 CSC
hub 1-0:1.0: port 7, status 0501, change 0000, 480 Mb/s
ehci_hcd 0000:00:1d.7: port 7 low speed --> companion
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 2:0:0:0: Attached scsi CD-ROM sr0
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 2:0:0:0: Attached scsi generic sg1 type 5
intel_rng: Firmware space is locked read-only. If you can't or
intel_rng: don't want to disable this in firmware setup, and if
intel_rng: you are certain that your system has a functional
intel_rng: RNG, try using the 'no_fwh_detect' option.
ehci_hcd 0000:00:1d.7: GetStatus port 7 status 003002 POWER OWNER sig=se0 CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt fe80
hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000
drivers/usb/core/inode.c: creating file '001'
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.27-rc5-usb uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.0
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
drivers/usb/core/inode.c: creating file '003'
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: detected 2 ports
uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:1d.1: Performing full reset
uhci_hcd 0000:00:1d.1: supports USB remote wakeup
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002060
usb usb3: default language 0x0409
usb usb3: uevent
usb usb3: usb_probe_device
usb usb3: configuration #1 chosen from 1 choice
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: uevent
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is good
hub 3-0:1.0: trying to enable port power on non-switchable hub
drivers/usb/core/inode.c: creating file '001'
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.27-rc5-usb uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.1
hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
drivers/usb/core/inode.c: creating file '004'
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: detected 2 ports
uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:1d.2: Performing full reset
uhci_hcd 0000:00:1d.2: supports USB remote wakeup
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002040
usb usb4: default language 0x0409
usb usb4: uevent
usb usb4: usb_probe_device
usb usb4: configuration #1 chosen from 1 choice
usb usb4: adding 4-0:1.0 (config #1, interface 0)
usb 4-0:1.0: uevent
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: no power switching (usb 1.0)
hub 4-0:1.0: individual port over-current protection
hub 4-0:1.0: power on to power good time: 2ms
hub 4-0:1.0: local power source is good
hub 4-0:1.0: trying to enable port power on non-switchable hub
uhci_hcd 0000:00:1d.2: port 1 portsc 01ab,00
hub 4-0:1.0: port 1: status 0301 change 0003
drivers/usb/core/inode.c: creating file '001'
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.27-rc5-usb uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.2
hub 4-0:1.0: state 7 ports 2 chg 0002 evt 0000
hub 4-0:1.0: port 1, status 0301, change 0000, 1.5 Mb/s
uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.3: setting latency timer to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
drivers/usb/core/inode.c: creating file '005'
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: detected 2 ports
uhci_hcd 0000:00:1d.3: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:1d.3: Performing full reset
uhci_hcd 0000:00:1d.3: supports USB remote wakeup
uhci_hcd 0000:00:1d.3: irq 16, io base 0x00002020
usb usb5: default language 0x0409
usb usb5: uevent
usb usb5: usb_probe_device
usb usb5: configuration #1 chosen from 1 choice
usb usb5: adding 5-0:1.0 (config #1, interface 0)
usb 5-0:1.0: uevent
hub 5-0:1.0: usb_probe_interface
hub 5-0:1.0: usb_probe_interface - got id
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
hub 5-0:1.0: standalone hub
hub 5-0:1.0: no power switching (usb 1.0)
hub 5-0:1.0: individual port over-current protection
hub 5-0:1.0: power on to power good time: 2ms
hub 5-0:1.0: local power source is good
hub 5-0:1.0: trying to enable port power on non-switchable hub
uhci_hcd 0000:00:1d.3: port 1 portsc 01ab,00
hub 5-0:1.0: port 1: status 0301 change 0003
usb 4-1: new low speed USB device using uhci_hcd and address 2
drivers/usb/core/inode.c: creating file '001'
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.27-rc5-usb uhci_hcd
usb usb5: SerialNumber: 0000:00:1d.3
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
HDA Intel 0000:00:1b.0: setting latency timer to 64
usb 4-1: skipped 1 descriptor after interface
usb 4-1: skipped 1 descriptor after interface
usb 4-1: default language 0x0409
usb 4-1: uevent
usb 4-1: usb_probe_device
usb 4-1: configuration #1 chosen from 1 choice
i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) -> IRQ 19
e1000e 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
e1000e 0000:01:00.0: setting latency timer to 64
piix 0000:00:1f.1: IDE controller (0x8086:0x27df rev 0x01)
PIIX_IDE 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
piix 0000:00:1f.1: IDE port disabled
piix 0000:00:1f.1: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x20b0-0x20b7
Probing IDE interface ide0...
usb 4-1: adding 4-1:1.0 (config #1, interface 0)
usb 4-1:1.0: uevent
usb 4-1: adding 4-1:1.1 (config #1, interface 1)
usb 4-1:1.1: uevent
drivers/usb/core/inode.c: creating file '002'
usb 4-1: New USB device found, idVendor=05a4, idProduct=9841
usb 4-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 4-1: Product: USB Compliant Keyboard
hub 5-0:1.0: state 7 ports 2 chg 0002 evt 0000
hub 5-0:1.0: port 1, status 0301, change 0000, 1.5 Mb/s
e1000e 0000:01:00.0: Warning: detected DSPD enabled in EEPROM
usb 5-1: new low speed USB device using uhci_hcd and address 2
0000:01:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:16:76:04:ff:09
0000:01:00.0: eth0: Intel(R) PRO/1000 Network Connection
0000:01:00.0: eth0: MAC: 2, PHY: 2, PBA No: ffffff-0ff
usb 5-1: skipped 1 descriptor after interface
usb 5-1: default language 0x0409
usb 5-1: uevent
usb 5-1: usb_probe_device
usb 5-1: configuration #1 chosen from 1 choice
usb 5-1: adding 5-1:1.0 (config #1, interface 0)
usb 5-1:1.0: uevent
drivers/usb/core/inode.c: creating file '002'
usb 5-1: New USB device found, idVendor=046d, idProduct=c50d
usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 5-1: Product: USB Receiver
usb 5-1: Manufacturer: Logitech
usbcore: registered new interface driver hiddev
usbhid 4-1:1.0: usb_probe_interface
usbhid 4-1:1.0: usb_probe_interface - got id
input: USB Compliant Keyboard as /class/input/input3
uhci_hcd 0000:00:1d.2: reserve dev 2 ep81-INT, period 8, phase 4, 118 us
input: USB HID v1.10 Keyboard [USB Compliant Keyboard] on usb-0000:00:1d.2-1
usbhid 4-1:1.1: usb_probe_interface
usbhid 4-1:1.1: usb_probe_interface - got id
input: USB Compliant Keyboard as /class/input/input4
uhci_hcd 0000:00:1d.2: reserve dev 2 ep82-INT, period 8, phase 4, 99 us
input: USB HID v1.10 Device [USB Compliant Keyboard] on usb-0000:00:1d.2-1
usbhid 5-1:1.0: usb_probe_interface
usbhid 5-1:1.0: usb_probe_interface - got id
input: Logitech USB Receiver as /class/input/input5
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1d.3-1
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
usb usb2: suspend_rh (auto-stop)
usb usb3: suspend_rh (auto-stop)
hda: LITE-ON DVD SOHD-16P9SV, ATAPI CD/DVD-ROM drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/33 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hub 1-0:1.0: hub_suspend
usb usb1: bus auto-suspend
ehci_hcd 0000:00:1d.7: suspend root hub
hub 2-0:1.0: hub_suspend
usb usb2: bus auto-suspend
usb usb2: suspend_rh
hub 3-0:1.0: hub_suspend
usb usb3: bus auto-suspend
usb usb3: suspend_rh
hda: ATAPI 63X DVD-ROM drive, 254kB Cache
Adding 979924k swap on /dev/sda6. Priority:-1 extents:1 across:979924k
EXT3 FS on dm-0, internal journal
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
i2c-adapter i2c-0: lm85: Detected SMSC chip
i2c-adapter i2c-0: lm85: Unrecognized version/stepping 0x68 Defaulting to Generic LM85.
fuse init (API version 7.9)
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Bridge firewalling registered
br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
device eth0 entered promiscuous mode
ADDRCONF(NETDEV_UP): eth0: link is not ready
0000:01:00.0: eth0: Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
0000:01:00.0: eth0: 10/100 speed: disabling TSO
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
br0: no IPv6 routers present
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
eth0: no IPv6 routers present
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
device vbox0 entered promiscuous mode
br0: port 2(vbox0) entering learning state
br0: topology change detected, propagating
br0: port 2(vbox0) entering forwarding state
[drm] Initialized drm 1.1.0 20060810
pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:02.0: setting latency timer to 64
[drm] Initialized i915 1.6.0 20060119 on minor 0
uhci_hcd 0000:00:1d.3: reserve dev 2 ep81-INT, period 8, phase 4, 118 us
uhci_hcd 0000:00:1d.3: release dev 2 ep81-INT, period 8, phase 4, 118 us
uhci_hcd 0000:00:1d.3: reserve dev 2 ep81-INT, period 8, phase 4, 118 us
vbox0: no IPv6 routers present
Linux version 2.6.27-rc5-usb (root@faramir) (gcc version 4.3.1 (Debian 4.3.1-9) ) #68 SMP Sat Aug 30 15:57:37 CEST 2008
Command line: root=/dev/mapper/main-root ro vga=791 quiet
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007f674000 (usable)
BIOS-e820: 000000007f674000 - 000000007f6e9000 (ACPI NVS)
BIOS-e820: 000000007f6e9000 - 000000007f6ec000 (usable)
BIOS-e820: 000000007f6ec000 - 000000007f6ff000 (ACPI data)
BIOS-e820: 000000007f6ff000 - 000000007f700000 (usable)
last_pfn = 0x7f700 max_arch_pfn = 0x3ffffffff
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
init_memory_mapping
0000000000 - 007f600000 page 2M
007f600000 - 007f700000 page 4k
kernel direct mapping tables up to 7f700000 @ 8000-c000
last_map_addr: 7f700000 end: 7f700000
RAMDISK: 37d18000 - 37fefb8e
DMI 2.3 present.
ACPI: RSDP 000FE020, 0014 (r0 INTEL )
ACPI: RSDT 7F6FDE48, 0058 (r1 INTEL D945GCZ FF9 MSFT 1000013)
ACPI: FACP 7F6FCF10, 0074 (r1 INTEL D945GCZ FF9 MSFT 1000013)
ACPI: DSDT 7F6F7010, 4348 (r1 INTEL D945GCZ FF9 MSFT 1000013)
ACPI: FACS 7F6E2C40, 0040
ACPI: APIC 7F6FCE10, 0078 (r1 INTEL D945GCZ FF9 MSFT 1000013)
ACPI: WDDT 7F6F6F90, 0040 (r1 INTEL D945GCZ FF9 MSFT 1000013)
ACPI: MCFG 7F6F6F10, 003C (r1 INTEL D945GCZ FF9 MSFT 1000013)
ACPI: ASF! 7F6FCD10, 00A6 (r32 INTEL D945GCZ FF9 MSFT 1000013)
ACPI: HPET 7F6F6E90, 0038 (r1 INTEL D945GCZ FF9 MSFT 1000013)
ACPI: SSDT 7F6FDC10, 01BC (r1 INTEL CpuPm FF9 MSFT 1000013)
ACPI: SSDT 7F6FDA10, 0175 (r1 INTEL Cpu0Ist FF9 MSFT 1000013)
ACPI: SSDT 7F6FD810, 0175 (r1 INTEL Cpu1Ist FF9 MSFT 1000013)
ACPI: SSDT 7F6FD610, 0175 (r1 INTEL Cpu2Ist FF9 MSFT 1000013)
ACPI: SSDT 7F6FD410, 0175 (r1 INTEL Cpu3Ist FF9 MSFT 1000013)
ACPI: SSDT 7F6F6E10, 002F (r1 INTEL SetupVar FF9 MSFT 1000013)
ACPI: TCPA 7F6E4D90, 0032 (r1 INTEL TIANO 2 MSFT 1000013)
No NUMA configuration found
Faking a node at 0000000000000000-000000007f700000
Bootmem setup node 0 0000000000000000-000000007f700000
NODE_DATA [0000000000001000 - 0000000000004fff]
bootmap [000000000000a000 - 0000000000019edf] pages 10
(6 early reservations) ==> bootmem [0000000000 - 007f700000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
#2 [0000200000 - 000074e4e0] TEXT DATA BSS ==> [0000200000 - 000074e4e0]
#3 [0037d18000 - 0037fefb8e] RAMDISK ==> [0037d18000 - 0037fefb8e]
#4 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
#5 [0000008000 - 000000a000] PGTABLE ==> [0000008000 - 000000a000]
found SMP MP-table at [ffff8800000fe680] 000fe680
[ffffe20000000000-ffffe20001ffffff] PMD -> [ffff880001200000-ffff8800031fffff] on node 0
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x00100000
Movable zone start PFN for each node
early_node_map[4] active PFN ranges
0: 0x00000000 -> 0x0000009f
0: 0x00000100 -> 0x0007f674
0: 0x0007f6e9 -> 0x0007f6ec
0: 0x0007f6ff -> 0x0007f700
On node 0 totalpages: 521751
DMA zone: 2474 pages, LIFO batch:0
DMA32 zone: 509660 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 0, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 4 CPUs, 2 hotplug CPUs
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
PM: Registered nosave memory: 000000007f674000 - 000000007f6e9000
PM: Registered nosave memory: 000000007f6ec000 - 000000007f6ff000
Allocating PCI resources starting at 80000000 (gap: 7f700000:80900000)
PERCPU: Allocating 47648 bytes of per cpu data
NR_CPUS: 8, nr_cpu_ids: 4, nr_node_ids 1
Built 1 zonelists in Node order, mobility grouping on. Total pages: 512134
Policy zone: DMA32
Kernel command line: root=/dev/mapper/main-root ro vga=791 quiet
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
TSC calibrated against PM_TIMER
Detected 3199.879 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Checking aperture...
No AGP bridge found
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
Memory: 2045500k/2087936k available (2287k kernel code, 41504k reserved, 1438k data, 368k init)
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
hpet clockevent registered
Calibrating delay loop (skipped), value calculated using timer frequency.. 6399.75 BogoMIPS (lpj=12799516)
Security Framework initialized
SELinux: Disabled at boot.
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Mount-cache hash table entries: 256
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU 0/0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM1)
using mwait in idle threads.
ACPI: Core revision 20080609
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Pentium(R) D CPU 3.20GHz stepping 07
Using local APIC timer interrupts.
APIC timer calibration result 12499522
Detected 12.499 MHz APIC timer.
Booting processor 1/1 ip 6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 6399.95 BogoMIPS (lpj=12799904)
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM1)
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: Intel(R) Pentium(R) D CPU 3.20GHz stepping 07
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (12799.71 BogoMIPS).
CPU0 attaching sched-domain:
domain 0: span 0-1 level CPU
groups: 0 1
domain 1: span 0-1 level NODE
groups: 0-1
CPU1 attaching sched-domain:
domain 0: span 0-1 level CPU
groups: 1 0
domain 1: span 0-1 level NODE
groups: 0-1
net_namespace: 1552 bytes
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Found Intel Corporation 945G/GZ/P/PL Express Memory Controller Hub without MMCONFIG support.
PCI: Using configuration type 1 for base access
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.2: PME# disabled
pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.3: PME# disabled
pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.4: PME# disabled
pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.5: PME# disabled
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
pci 0000:01:00.0: PME# disabled
pci 0000:01:00.3: PME# supported from D0 D3hot D3cold
pci 0000:01:00.3: PME# disabled
pci 0000:01:00.4: PME# supported from D0 D3hot D3cold
pci 0000:01:00.4: PME# disabled
PCI: bridge 0000:00:1c.0 io port: [1000, 1fff]
PCI: bridge 0000:00:1c.0 32bit mmio: [90000000, 901fffff]
PCI: bridge 0000:00:1c.2 32bit mmio: [90300000, 903fffff]
PCI: bridge 0000:00:1c.3 32bit mmio: [90400000, 904fffff]
PCI: bridge 0000:00:1c.4 32bit mmio: [90500000, 905fffff]
PCI: bridge 0000:00:1c.5 32bit mmio: [90600000, 906fffff]
pci 0000:00:1e.0: transparent bridge
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX5._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 *10 11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 *9 10 11 12)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 *9 10 11 12)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:00: parse allocated resources
pnp 00:00: add io 0xcf8-0xcff flags 0x1
pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
pnp 00:01: parse allocated resources
pnp 00:01: add mem 0xf0000000-0xf3ffffff flags 0x0
pnp 00:01: add mem 0xfed13000-0xfed13fff flags 0x0
pnp 00:01: add mem 0xfed14000-0xfed17fff flags 0x0
pnp 00:01: add mem 0xfed18000-0xfed18fff flags 0x0
pnp 00:01: add mem 0xfed19000-0xfed19fff flags 0x0
pnp 00:01: add mem 0xfed1c000-0xfed1ffff flags 0x0
pnp 00:01: add mem 0xfed20000-0xfed3ffff flags 0x0
pnp 00:01: add mem 0xfed45000-0xfed99fff flags 0x0
pnp 00:01: add mem 0xc0000-0xdffff flags 0x0
pnp 00:01: add mem 0xe0000-0xfffff flags 0x0
pnp 00:01: PNP0c02: calling quirk_system_pci_resources+0x0/0x179
pnp 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:02: parse allocated resources
pnp 00:02: add io 0x0-0xf flags 0x1
pnp 00:02: add io 0x81-0x83 flags 0x1
pnp 00:02: add io 0x87-0x87 flags 0x1
pnp 00:02: add io 0x89-0x8b flags 0x1
pnp 00:02: add io 0x8f-0x8f flags 0x1
pnp 00:02: add io 0xc0-0xdf flags 0x1
pnp 00:02: add dma 4 flags 0x0
pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
pnp 00:03: parse allocated resources
pnp 00:03: add io 0x70-0x71 flags 0x1
pnp 00:03: add io 0x74-0x77 flags 0x1
pnp 00:03: add irq 8 flags 0x1
pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
pnp 00:04: parse allocated resources
pnp 00:04: add io 0xf0-0xf0 flags 0x1
pnp 00:04: add irq 13 flags 0x1
pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
pnp 00:05: parse allocated resources
pnp 00:05: add io 0x61-0x61 flags 0x1
pnp 00:05: Plug and Play ACPI device, IDs PNP0800 (active)
pnp 00:06: parse allocated resources
pnp 00:06: add io 0x500-0x53f flags 0x1
pnp 00:06: add io 0x400-0x47f flags 0x1
pnp 00:06: add io 0x92-0x92 flags 0x1
pnp 00:06: add io 0x680-0x6ff flags 0x1
pnp 00:06: add io 0x10-0x1f flags 0x1
pnp 00:06: add io 0x72-0x73 flags 0x1
pnp 00:06: add io 0x80-0x80 flags 0x1
pnp 00:06: add io 0x84-0x86 flags 0x1
pnp 00:06: add io 0x88-0x88 flags 0x1
pnp 00:06: add io 0x8c-0x8e flags 0x1
pnp 00:06: add io 0x90-0x9f flags 0x1
pnp 00:06: PNP0c02: calling quirk_system_pci_resources+0x0/0x179
pnp 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:07: parse allocated resources
pnp 00:07: add mem 0xfed40000-0xfed44fff flags 0x0
pnp 00:07: PNP0c02: calling quirk_system_pci_resources+0x0/0x179
pnp 00:07: Plug and Play ACPI device, IDs PNP0c31 PNP0c02 (active)
pnp 00:08: parse allocated resources
pnp 00:08: add io 0x60-0x60 flags 0x1
pnp 00:08: add io 0x64-0x64 flags 0x1
pnp 00:08: PNP0c02: calling quirk_system_pci_resources+0x0/0x179
pnp 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:09: parse allocated resources
pnp 00:09: add io 0x3f0-0x3f5 flags 0x1
pnp 00:09: add io 0x3f0-0x3f0 flags 0x1
pnp 00:09: add irq 6 flags 0x1
pnp 00:09: add dma 2 flags 0x0
pnp 00:09: parse resource options
pnp 00:09: dependent set 0 (preferred) io min 0x3f0 max 0x3f0 align 1 size 6 flags 0x1
pnp 00:09: dependent set 0 (preferred) io min 0x3f7 max 0x3f7 align 1 size 1 flags 0x1
pnp 00:09: dependent set 0 (preferred) irq 6 flags 0x1
pnp 00:09: dependent set 0 (preferred) dma 2 (bitmask 0x4) flags 0x0
pnp 00:09: Plug and Play ACPI device, IDs PNP0700 (active)
pnp 00:0a: parse allocated resources
pnp 00:0a: add io 0x378-0x37f flags 0x1
pnp 00:0a: add io 0x778-0x77f flags 0x1
pnp 00:0a: add irq 7 flags 0x1
pnp 00:0a: add dma 0 flags 0x10000000
pnp 00:0a: parse resource options
pnp 00:0a: dependent set 0 (preferred) io min 0x378 max 0x378 align 1 size 8 flags 0x1
pnp 00:0a: dependent set 0 (preferred) io min 0x778 max 0x778 align 1 size 8 flags 0x1
pnp 00:0a: dependent set 0 (preferred) irq 5 7 flags 0x1
pnp 00:0a: dependent set 0 (preferred) dma 1 3 (bitmask 0xa) flags 0x0
pnp 00:0a: dependent set 1 (preferred) io min 0x278 max 0x278 align 1 size 8 flags 0x1
pnp 00:0a: dependent set 1 (preferred) io min 0x678 max 0x678 align 1 size 8 flags 0x1
pnp 00:0a: dependent set 1 (preferred) irq 5 7 flags 0x1
pnp 00:0a: dependent set 1 (preferred) dma 1 3 (bitmask 0xa) flags 0x0
pnp 00:0a: dependent set 2 (preferred) io min 0x3bc max 0x3bc align 1 size 4 flags 0x1
pnp 00:0a: dependent set 2 (preferred) io min 0x7bc max 0x7bc align 1 size 4 flags 0x1
pnp 00:0a: dependent set 2 (preferred) irq 5 7 flags 0x1
pnp 00:0a: dependent set 2 (preferred) dma 1 3 (bitmask 0xa) flags 0x0
pnp 00:0a: Plug and Play ACPI device, IDs PNP0401 (active)
pnp 00:0b: parse allocated resources
pnp 00:0b: add io 0x3f8-0x3ff flags 0x1
pnp 00:0b: add irq 4 flags 0x1
pnp 00:0b: parse resource options
pnp 00:0b: dependent set 0 (preferred) io min 0x3f8 max 0x3f8 align 1 size 8 flags 0x1
pnp 00:0b: dependent set 0 (preferred) irq 4 flags 0x1
pnp 00:0b: dependent set 1 (preferred) io min 0x3e8 max 0x3e8 align 1 size 8 flags 0x1
pnp 00:0b: dependent set 1 (preferred) irq 4 flags 0x1
pnp 00:0b: dependent set 2 (preferred) io min 0x2f8 max 0x2f8 align 1 size 8 flags 0x1
pnp 00:0b: dependent set 2 (preferred) irq 3 flags 0x1
pnp 00:0b: dependent set 3 (preferred) io min 0x2e8 max 0x2e8 align 1 size 8 flags 0x1
pnp 00:0b: dependent set 3 (preferred) irq 3 flags 0x1
pnp 00:0b: dependent set 4 (functional) io min 0x100 max 0x3f8 align 8 size 8 flags 0x1
pnp 00:0b: dependent set 4 (functional) irq 1 3 4 5 6 7 8 10 11 12 13 14 15 flags 0x1
pnp 00:0b: Plug and Play ACPI device, IDs PNP0501 (active)
pnp 00:0c: parse allocated resources
pnp 00:0c: add mem 0xfec00000-0xfec000ff flags 0x0
pnp 00:0c: Plug and Play ACPI device, IDs PNP0003 (active)
pnp 00:0d: parse allocated resources
pnp 00:0d: add mem 0xfed00000-0xfed003ff flags 0x0
pnp 00:0d: Plug and Play ACPI device, IDs PNP0103 (active)
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI-GART: No AMD northbridge found.
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
ACPI: RTC can wake from S4
pnp: the driver 'system' has been registered
system 00:01: iomem range 0xf0000000-0xf3ffffff has been reserved
system 00:01: iomem range 0xfed13000-0xfed13fff has been reserved
system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved
system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved
system 00:01: iomem range 0xfed20000-0xfed3ffff has been reserved
system 00:01: iomem range 0xfed45000-0xfed99fff has been reserved
system 00:01: iomem range 0xc0000-0xdffff has been reserved
system 00:01: iomem range 0xe0000-0xfffff could not be reserved
system 00:01: driver attached
system 00:06: ioport range 0x500-0x53f has been reserved
system 00:06: ioport range 0x400-0x47f has been reserved
system 00:06: ioport range 0x680-0x6ff has been reserved
system 00:06: driver attached
system 00:07: iomem range 0xfed40000-0xfed44fff has been reserved
system 00:07: driver attached
system 00:08: driver attached
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:01
pci 0000:00:1c.0: IO window: 0x1000-0x1fff
pci 0000:00:1c.0: MEM window: 0x90000000-0x901fffff
pci 0000:00:1c.0: PREFETCH window: disabled
pci 0000:00:1c.2: PCI bridge, secondary bus 0000:02
pci 0000:00:1c.2: IO window: disabled
pci 0000:00:1c.2: MEM window: 0x90300000-0x903fffff
pci 0000:00:1c.2: PREFETCH window: disabled
pci 0000:00:1c.3: PCI bridge, secondary bus 0000:03
pci 0000:00:1c.3: IO window: disabled
pci 0000:00:1c.3: MEM window: 0x90400000-0x904fffff
pci 0000:00:1c.3: PREFETCH window: disabled
pci 0000:00:1c.4: PCI bridge, secondary bus 0000:04
pci 0000:00:1c.4: IO window: disabled
pci 0000:00:1c.4: MEM window: 0x90500000-0x905fffff
pci 0000:00:1c.4: PREFETCH window: disabled
pci 0000:00:1c.5: PCI bridge, secondary bus 0000:05
pci 0000:00:1c.5: IO window: disabled
pci 0000:00:1c.5: MEM window: 0x90600000-0x906fffff
pci 0000:00:1c.5: PREFETCH window: disabled
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:06
pci 0000:00:1e.0: IO window: disabled
pci 0000:00:1e.0: MEM window: disabled
pci 0000:00:1e.0: PREFETCH window: disabled
pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
pci 0000:00:1c.2: setting latency timer to 64
pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
pci 0000:00:1c.3: setting latency timer to 64
pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.4: setting latency timer to 64
pci 0000:00:1c.5: PCI INT B -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.5: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [0, ffffffffffffffff]
bus: 01 index 0 io port: [1000, 1fff]
bus: 01 index 1 mmio: [90000000, 901fffff]
bus: 01 index 2 mmio: [0, 0]
bus: 01 index 3 mmio: [0, 0]
bus: 02 index 0 mmio: [0, 0]
bus: 02 index 1 mmio: [90300000, 903fffff]
bus: 02 index 2 mmio: [0, 0]
bus: 02 index 3 mmio: [0, 0]
bus: 03 index 0 mmio: [0, 0]
bus: 03 index 1 mmio: [90400000, 904fffff]
bus: 03 index 2 mmio: [0, 0]
bus: 03 index 3 mmio: [0, 0]
bus: 04 index 0 mmio: [0, 0]
bus: 04 index 1 mmio: [90500000, 905fffff]
bus: 04 index 2 mmio: [0, 0]
bus: 04 index 3 mmio: [0, 0]
bus: 05 index 0 mmio: [0, 0]
bus: 05 index 1 mmio: [90600000, 906fffff]
bus: 05 index 2 mmio: [0, 0]
bus: 05 index 3 mmio: [0, 0]
bus: 06 index 0 mmio: [0, 0]
bus: 06 index 1 mmio: [0, 0]
bus: 06 index 2 mmio: [0, 0]
bus: 06 index 3 io port: [0, ffff]
bus: 06 index 4 mmio: [0, ffffffffffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 9, 2097152 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
NET: Registered protocol family 1
checking if image is initramfs... it is
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
Freeing initrd memory: 2910k freed
audit: initializing netlink socket (disabled)
type=2000 audit(1220104992.524:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
msgmni has been set to 4000
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:02.0: Boot video device
pci 0000:00:1d.0: uhci_check_and_reset_hc: legsup = 0x0f10
pci 0000:00:1d.0: Performing full reset
pci 0000:00:1d.1: uhci_check_and_reset_hc: legsup = 0x0010
pci 0000:00:1d.1: Performing full reset
pci 0000:00:1d.2: uhci_check_and_reset_hc: legsup = 0x0010
pci 0000:00:1d.2: Performing full reset
pci 0000:00:1d.3: uhci_check_and_reset_hc: legsup = 0x0010
pci 0000:00:1d.3: Performing full reset
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.0: found MSI capability
pci_express 0000:00:1c.0:pcie00: allocate port service
pci_express 0000:00:1c.0:pcie02: allocate port service
pcieport-driver 0000:00:1c.2: setting latency timer to 64
pcieport-driver 0000:00:1c.2: found MSI capability
pci_express 0000:00:1c.2:pcie00: allocate port service
pci_express 0000:00:1c.2:pcie02: allocate port service
pcieport-driver 0000:00:1c.3: setting latency timer to 64
pcieport-driver 0000:00:1c.3: found MSI capability
pci_express 0000:00:1c.3:pcie00: allocate port service
pci_express 0000:00:1c.3:pcie02: allocate port service
pcieport-driver 0000:00:1c.4: setting latency timer to 64
pcieport-driver 0000:00:1c.4: found MSI capability
pci_express 0000:00:1c.4:pcie00: allocate port service
pci_express 0000:00:1c.4:pcie02: allocate port service
pcieport-driver 0000:00:1c.5: setting latency timer to 64
pcieport-driver 0000:00:1c.5: found MSI capability
pci_express 0000:00:1c.5:pcie00: allocate port service
pci_express 0000:00:1c.5:pcie02: allocate port service
vesafb: framebuffer at 0x80000000, mapped to 0xffffc20000a00000, using 3072k, total 7872k
vesafb: mode is 1024x768x16, linelength=2048, pages=4
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
hpet_resources: 0xfed00000 is busy
Linux agpgart interface v0.103
Serial: 8250/16550 driver4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
pnp: the driver 'serial' has been registered
00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial 00:0b: driver attached
serial 0000:01:00.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18
0000:01:00.3: ttyS1 at I/O 0x1020 (irq = 18) is a 16550A
brd: module loaded
pnp: the driver 'i8042 kbd' has been registered
pnp: the driver 'i8042 aux' has been registered
pnp: the driver 'i8042 kbd' has been unregistered
pnp: the driver 'i8042 aux' has been unregistered
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
pnp: the driver 'rtc_cmos' has been registered
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, hpet irqs
rtc_cmos 00:03: driver attached
cpuidle: using governor ladder
cpuidle: using governor menu
TCP bic registered
NET: Registered protocol family 17
rtc_cmos 00:03: setting system clock to 2008-08-30 14:03:13 UTC (1220104993)
Freeing unused kernel memory: 368k freed
No dock devices found.
SCSI subsystem initialized
libata version 3.00 loaded.
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m1024@0x902c4000 port 0x902c4100 irq 506
ata2: SATA max UDMA/133 abar m1024@0x902c4000 port 0x902c4180 irq 506
ata3: SATA max UDMA/133 abar m1024@0x902c4000 port 0x902c4200 irq 506
ata4: SATA max UDMA/133 abar m1024@0x902c4000 port 0x902c4280 irq 506
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: HDT722516DLA380, V43OA96A, max UDMA/133
ata1.00: 321672960 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATAPI: Optiarc DVD RW AD-7170S, 1.00, max UDMA/66
ata3.00: configured for UDMA/66
ata4: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access ATA HDT722516DLA380 V43O PQ: 0 ANSI: 5
scsi 2:0:0:0: CD-ROM Optiarc DVD RW AD-7170S 1.00 PQ: 0 ANSI: 5
processor ACPI0007:00: registered as cooling_device0
processor ACPI0007:01: registered as cooling_device1
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:0:0: [sda] 321672960 512-byte hardware sectors (164697 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 321672960 512-byte hardware sectors (164697 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 < sda5 sda6 > sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
udevd version 125 started
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
USB Universal Host Controller Interface driver v3.0
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: detected 2 ports
uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:1d.0: Performing full reset
uhci_hcd 0000:00:1d.0: supports USB remote wakeup
uhci_hcd 0000:00:1d.0: irq 23, io base 0x00002080
usb usb1: default language 0x0409
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: trying to enable port power on non-switchable hub
ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Sleep Button (CM) as /class/input/input1
Uniform Multi-Platform E-IDE driver
pnp: the driver 'parport_pc' has been registered
parport_pc 00:0a: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
ACPI: Sleep Button (CM) [SLPB]
hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
drivers/usb/core/inode.c: creating file '001'
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.27-rc5-usb uhci_hcd
usb usb1: SerialNumber: 0000:00:1d.0
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
drivers/usb/core/inode.c: creating file '002'
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: detected 2 ports
uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:1d.1: Performing full reset
uhci_hcd 0000:00:1d.1: supports USB remote wakeup
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002060
usb usb2: default language 0x0409
usb usb2: uevent
usb usb2: usb_probe_device
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: trying to enable port power on non-switchable hub
Driver 'sr' needs updating - please use bus_type methods
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 2:0:0:0: Attached scsi CD-ROM sr0
parport0: Printer, HEWLETT-PACKARD PHOTOSMART P1100
parport_pc 00:0a: driver attached
input: PC Speaker as /class/input/input2
hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000
drivers/usb/core/inode.c: creating file '001'
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.27-rc5-usb uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.1
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
drivers/usb/core/inode.c: creating file '003'
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: detected 2 ports
uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:1d.2: Performing full reset
uhci_hcd 0000:00:1d.2: supports USB remote wakeup
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002040
usb usb3: default language 0x0409
usb usb3: uevent
usb usb3: usb_probe_device
usb usb3: configuration #1 chosen from 1 choice
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: uevent
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is good
hub 3-0:1.0: trying to enable port power on non-switchable hub
e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k2
e1000e: Copyright (c) 1999-2008 Intel Corporation.
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0460)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
uhci_hcd 0000:00:1d.2: port 1 portsc 01ab,00
hub 3-0:1.0: port 1: status 0301 change 0003
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 2:0:0:0: Attached scsi generic sg1 type 5
intel_rng: Firmware space is locked read-only. If you can't or
intel_rng: don't want to disable this in firmware setup, and if
intel_rng: you are certain that your system has a functional
intel_rng: RNG, try using the 'no_fwh_detect' option.
hub 3-0:1.0: state 7 ports 2 chg 0002 evt 0000
drivers/usb/core/inode.c: creating file '001'
hub 3-0:1.0: port 1, status 0301, change 0000, 1.5 Mb/s
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.27-rc5-usb uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.2
agpgart-intel 0000:00:00.0: Intel 945G Chipset
agpgart-intel 0000:00:00.0: detected 7932K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0x80000000
uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.3: setting latency timer to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
drivers/usb/core/inode.c: creating file '004'
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: detected 2 ports
uhci_hcd 0000:00:1d.3: uhci_check_and_reset_hc: cmd = 0x0000
uhci_hcd 0000:00:1d.3: Performing full reset
uhci_hcd 0000:00:1d.3: supports USB remote wakeup
uhci_hcd 0000:00:1d.3: irq 16, io base 0x00002020
usb usb4: default language 0x0409
usb usb4: uevent
usb usb4: usb_probe_device
usb usb4: configuration #1 chosen from 1 choice
usb usb4: adding 4-0:1.0 (config #1, interface 0)
usb 4-0:1.0: uevent
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: no power switching (usb 1.0)
hub 4-0:1.0: individual port over-current protection
hub 4-0:1.0: power on to power good time: 2ms
hub 4-0:1.0: local power source is good
hub 4-0:1.0: trying to enable port power on non-switchable hub
usb 3-1: new low speed USB device using uhci_hcd and address 2
uhci_hcd 0000:00:1d.3: port 1 portsc 01ab,00
hub 4-0:1.0: port 1: status 0301 change 0003
drivers/usb/core/inode.c: creating file '001'
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.27-rc5-usb uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.3
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
drivers/usb/core/inode.c: creating file '005'
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: reset hcs_params 0x104208 dbg=1 cc=4 pcc=2 ordered !ppc ports=8
ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7 uframes 1024 64 bit addr
ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 128 is not supported
ehci_hcd 0000:00:1d.7: supports USB remote wakeup
ehci_hcd 0000:00:1d.7: irq 23, io mem 0x902c4400
ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:1d.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN
ehci: waiting for khubd_idle
usb 3-1: skipped 1 descriptor after interface
usb 3-1: skipped 1 descriptor after interface
usb 3-1: default language 0x0409
usb 3-1: uevent
usb 3-1: usb_probe_device
usb 3-1: configuration #1 chosen from 1 choice
usb 3-1: adding 3-1:1.0 (config #1, interface 0)
usb 3-1:1.0: uevent
usb 3-1: adding 3-1:1.1 (config #1, interface 1)
usb 3-1:1.1: uevent
drivers/usb/core/inode.c: creating file '002'
usb 3-1: New USB device found, idVendor=05a4, idProduct=9841
usb 3-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 3-1: Product: USB Compliant Keyboard
hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0002
hub 4-0:1.0: state 7 ports 2 chg 0002 evt 0000
hub 4-0:1.0: port 1, status 0301, change 0000, 1.5 Mb/s
usb 4-1: new low speed USB device using uhci_hcd and address 2
usb 4-1: skipped 1 descriptor after interface
usb 4-1: default language 0x0409
usb 4-1: uevent
usb 4-1: usb_probe_device
usb 4-1: configuration #1 chosen from 1 choice
usb 4-1: adding 4-1:1.0 (config #1, interface 0)
usb 4-1:1.0: uevent
drivers/usb/core/inode.c: creating file '002'
usb 4-1: New USB device found, idVendor=046d, idProduct=c50d
usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 4-1: Product: USB Receiver
usb 4-1: Manufacturer: Logitech
ehci: got khubd_idle, resume ehci_run
usbcore: registered new interface driver hiddev
usbhid 3-1:1.0: usb_probe_interface
usbhid 3-1:1.0: usb_probe_interface - got id
usb 3-1: uhci_result_common: failed with status 440000
usb 3-1: uhci_result_common: failed with status 440000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: default language 0x0409
usb usb5: uevent
usb usb5: usb_probe_device
usb usb5: configuration #1 chosen from 1 choice
usb usb5: adding 5-0:1.0 (config #1, interface 0)
usb 5-0:1.0: uevent
hub 5-0:1.0: usb_probe_interface
hub 5-0:1.0: usb_probe_interface - got id
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
hub 5-0:1.0: standalone hub
hub 5-0:1.0: no power switching (usb 1.0)
hub 5-0:1.0: individual port over-current protection
hub 5-0:1.0: power on to power good time: 20ms
hub 5-0:1.0: local power source is good
hub 5-0:1.0: trying to enable port power on non-switchable hub
usb 3-1: uhci_result_common: failed with status 440000
usb 3-1: uhci_result_common: failed with status 440000
usb 3-1: uhci_result_common: failed with status 440000
usbhid 3-1:1.1: usb_probe_interface
usbhid 3-1:1.1: usb_probe_interface - got id
usb 3-1: uhci_result_common: failed with status 440000
usb 3-1: uhci_result_common: failed with status 440000
usb 3-1: uhci_result_common: failed with status 440000
hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0002
uhci_hcd 0000:00:1d.2: port 1 portsc 008a,00
hub 3-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
usb 3-1: uhci_result_common: failed with status 440000
usb 3-1: uhci_result_common: failed with status 440000
ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001403 POWER sig=k CSC CONNECT
hub 5-0:1.0: port 5: status 0501 change 0001
ehci_hcd 0000:00:1d.7: GetStatus port 7 status 001403 POWER sig=k CSC CONNECT
hub 5-0:1.0: port 7: status 0501 change 0001
hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
usb 3-1: USB disconnect, address 2
usb 3-1: unregistering device
usb 3-1: usb_disable_device nuking all URBs
usb 3-1: unregistering interface 3-1:1.0
usb 3-1:1.0: uevent
usb 3-1: unregistering interface 3-1:1.1
usb 3-1:1.1: uevent
usb 3-1: uevent
hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002
uhci_hcd 0000:00:1d.3: port 1 portsc 008a,00
hub 4-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
usbhid 4-1:1.0: usb_probe_interface
usbhid 4-1:1.0: usb_probe_interface - got id
usb 4-1: uhci_result_common: failed with status 440000
usb 4-1: uhci_result_common: failed with status 440000
usb 4-1: uhci_result_common: failed with status 440000
usb 4-1: uhci_result_common: failed with status 440000
usb 4-1: uhci_result_common: failed with status 440000
drivers/usb/core/inode.c: creating file '001'
usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: EHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.27-rc5-usb ehci_hcd
usb usb5: SerialNumber: 0000:00:1d.7
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
HDA Intel 0000:00:1b.0: setting latency timer to 64
usb usb1: suspend_rh (auto-stop)
usb usb2: suspend_rh (auto-stop)
hub 4-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
usb 4-1: USB disconnect, address 2
usb 4-1: unregistering device
usb 4-1: usb_disable_device nuking all URBs
usb 4-1: unregistering interface 4-1:1.0
usb 4-1:1.0: uevent
usb 4-1: uevent
hub 5-0:1.0: state 7 ports 8 chg 00a0 evt 0000
hub 5-0:1.0: port 5, status 0501, change 0000, 480 Mb/s
ehci_hcd 0000:00:1d.7: port 5 low speed --> companion
piix 0000:00:1f.1: IDE controller (0x8086:0x27df rev 0x01)
PIIX_IDE 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
piix 0000:00:1f.1: IDE port disabled
piix 0000:00:1f.1: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x20b0-0x20b7
Probing IDE interface ide0...
ehci_hcd 0000:00:1d.7: GetStatus port 5 status 003002 POWER OWNER sig=se0 CSC
hub 5-0:1.0: port 7, status 0501, change 0000, 480 Mb/s
ehci_hcd 0000:00:1d.7: port 7 low speed --> companion
ehci_hcd 0000:00:1d.7: GetStatus port 7 status 003002 POWER OWNER sig=se0 CSC
hub 5-0:1.0: state 7 ports 8 chg 0000 evt fe80
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0002
uhci_hcd 0000:00:1d.2: port 1 portsc 01a3,00
hub 3-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
usb 3-1: new low speed USB device using uhci_hcd and address 3
usb 3-1: skipped 1 descriptor after interface
usb 3-1: skipped 1 descriptor after interface
usb 3-1: default language 0x0409
usb 3-1: uevent
usb 3-1: usb_probe_device
usb 3-1: configuration #1 chosen from 1 choice
usb 3-1: adding 3-1:1.0 (config #1, interface 0)
usb 3-1:1.0: uevent
usbhid 3-1:1.0: usb_probe_interface
usbhid 3-1:1.0: usb_probe_interface - got id
input: USB Compliant Keyboard as /class/input/input3
uhci_hcd 0000:00:1d.2: reserve dev 3 ep81-INT, period 8, phase 4, 118 us
input: USB HID v1.10 Keyboard [USB Compliant Keyboard] on usb-0000:00:1d.2-1
usb 3-1: adding 3-1:1.1 (config #1, interface 1)
usb 3-1:1.1: uevent
usbhid 3-1:1.1: usb_probe_interface
usbhid 3-1:1.1: usb_probe_interface - got id
input: USB Compliant Keyboard as /class/input/input4
hda: LITE-ON DVD SOHD-16P9SV, ATAPI CD/DVD-ROM drive
uhci_hcd 0000:00:1d.2: reserve dev 3 ep82-INT, period 8, phase 4, 99 us
input: USB HID v1.10 Device [USB Compliant Keyboard] on usb-0000:00:1d.2-1
drivers/usb/core/inode.c: creating file '003'
usb 3-1: New USB device found, idVendor=05a4, idProduct=9841
usb 3-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 3-1: Product: USB Compliant Keyboard
hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0002
uhci_hcd 0000:00:1d.3: port 1 portsc 01a3,00
hub 4-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
hub 4-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
usb 4-1: new low speed USB device using uhci_hcd and address 3
usb 4-1: skipped 1 descriptor after interface
usb 4-1: default language 0x0409
usb 4-1: uevent
usb 4-1: usb_probe_device
usb 4-1: configuration #1 chosen from 1 choice
usb 4-1: adding 4-1:1.0 (config #1, interface 0)
usb 4-1:1.0: uevent
usbhid 4-1:1.0: usb_probe_interface
usbhid 4-1:1.0: usb_probe_interface - got id
hub 1-0:1.0: hub_suspend
usb usb1: bus auto-suspend
usb usb1: suspend_rh
hub 2-0:1.0: hub_suspend
usb usb2: bus auto-suspend
usb usb2: suspend_rh
input: Logitech USB Receiver as /class/input/input5
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1d.3-1
drivers/usb/core/inode.c: creating file '003'
usb 4-1: New USB device found, idVendor=046d, idProduct=c50d
usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 4-1: Product: USB Receiver
usb 4-1: Manufacturer: Logitech
hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0002
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/33 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
e1000e 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
e1000e 0000:01:00.0: setting latency timer to 64
i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) -> IRQ 19
e1000e 0000:01:00.0: Warning: detected DSPD enabled in EEPROM
0000:01:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:16:76:04:ff:09
0000:01:00.0: eth0: Intel(R) PRO/1000 Network Connection
0000:01:00.0: eth0: MAC: 2, PHY: 2, PBA No: ffffff-0ff
hda: ATAPI 63X DVD-ROM drive, 254kB Cache
hub 5-0:1.0: hub_suspend
usb usb5: bus auto-suspend
ehci_hcd 0000:00:1d.7: suspend root hub
Adding 979924k swap on /dev/sda6. Priority:-1 extents:1 across:979924k
EXT3 FS on dm-0, internal journal
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
i2c-adapter i2c-0: lm85: Detected SMSC chip
i2c-adapter i2c-0: lm85: Unrecognized version/stepping 0x68 Defaulting to Generic LM85.
fuse init (API version 7.9)
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Bridge firewalling registered
br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
device eth0 entered promiscuous mode
ADDRCONF(NETDEV_UP): eth0: link is not ready
0000:01:00.0: eth0: Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
0000:01:00.0: eth0: 10/100 speed: disabling TSO
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
br0: no IPv6 routers present
eth0: no IPv6 routers present
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
device vbox0 entered promiscuous mode
br0: port 2(vbox0) entering learning state
br0: topology change detected, propagating
br0: port 2(vbox0) entering forwarding state
[drm] Initialized drm 1.1.0 20060810
pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:02.0: setting latency timer to 64
[drm] Initialized i915 1.6.0 20060119 on minor 0
uhci_hcd 0000:00:1d.3: reserve dev 3 ep81-INT, period 8, phase 4, 118 us
uhci_hcd 0000:00:1d.3: release dev 3 ep81-INT, period 8, phase 4, 118 us
uhci_hcd 0000:00:1d.3: reserve dev 3 ep81-INT, period 8, phase 4, 118 us
vbox0: no IPv6 routers present
\
 
 \ /
  Last update: 2008-08-30 16:43    [W:0.834 / U:0.016 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site