Messages in this thread | | | From | Jan Schneider <> | Subject | nvidia MCP78B ahci failed to IDENTIFY error on 2.6.26 | Date | Mon, 28 Jul 2008 12:03:38 +0200 |
| |
Hi,
I get the follwing errors when booting 2.6.26 on a FSC Esprimo P5625 (nvidia MCP78B).
------------[ cut here ]------------ WARNING: at drivers/ata/libata-core.c:5697 ata_host_activate+0xf6/0x100 [libata]() Modules linked in: 8250_pnp 8250 serial_core tg3(+) serio_raw ahci(+) ata_generic tpm_infineon tpm tpm_bios pata_acpi libata shpchp dock pci_hotplug ehci_hcd ohci_hcd usbcore container thermal button processor evdev Pid: 1937, comm: modprobe Not tainted 2.6.26 #1 [<c012706f>] warn_on_slowpath+0x5f/0x90 [<c01213d5>] finish_task_switch+0x95/0xa0 [<c0108c22>] dma_alloc_coherent+0x122/0x2b0 [<c025e2c1>] devres_add+0x31/0x50 [<c025f94c>] dmam_alloc_coherent+0x6c/0x90 [<f8bd529f>] ahci_port_resume+0x5f/0x70 [ahci] [<c025e2c1>] devres_add+0x31/0x50 [<f8bf893d>] ata_host_start+0xed/0x170 [libata] [<c02055ca>] pci_bus_write_config_byte+0x5a/0x70 [<f8bfcda6>] ata_host_activate+0xf6/0x100 [libata] [<f8bd6899>] ahci_init_one+0x899/0xac0 [ahci] [<c0209a96>] pci_device_probe+0x56/0x80 [<c025c682>] driver_probe_device+0x82/0x180 [<c025c7ec>] __driver_attach+0x6c/0x70 [<c025bdbb>] bus_for_each_dev+0x3b/0x60 [<c025c506>] driver_attach+0x16/0x20 [<c025c780>] __driver_attach+0x0/0x70 [<c025c1e9>] bus_add_driver+0xa9/0x210 [<c02099e0>] pci_device_remove+0x0/0x40 [<c025c95d>] driver_register+0x4d/0x120 [<c0209cbd>] __pci_register_driver+0x3d/0x80 [<c0149194>] sys_init_module+0x84/0x1b0 [<c0103da1>] sysenter_past_esp+0x6a/0x99 ======================= ---[ end trace 21da9b6136ad63e5 ]---
The serial ata harddisk does not appear.
---------[ lspci -n ]--------- 00:00.0 0500: 10de:0754 (rev a2) 00:01.0 0601: 10de:075c (rev a2) 00:01.1 0c05: 10de:0752 (rev a1) 00:01.2 0500: 10de:0751 (rev a1) 00:01.4 0500: 10de:0568 (rev a1) 00:02.0 0c03: 10de:077b (rev a1) 00:02.1 0c03: 10de:077c (rev a1) 00:04.0 0c03: 10de:077d (rev a1) 00:04.1 0c03: 10de:077e (rev a1) 00:07.0 0403: 10de:0774 (rev a1) 00:08.0 0604: 10de:075a (rev a1) 00:09.0 0101: 10de:0ad0 (rev a2) 00:0b.0 0604: 10de:0569 (rev a1) 00:10.0 0604: 10de:0778 (rev a1) 00:12.0 0604: 10de:075b (rev a1) 00:13.0 0604: 10de:077a (rev a1) 00:18.0 0600: 1022:1100 00:18.1 0600: 1022:1101 00:18.2 0600: 1022:1102 00:18.3 0600: 1022:1103 02:00.0 0300: 10de:084b (rev a2) 05:00.0 0200: 14e4:169b (rev 02) ----------------------------------
Full dmesg output:
Linux version 2.6.26 (root@pcbon14) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP PREEMPT Mon Jul 21 16:44:03 UTC 2008 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009dc00 (usable) BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 0000000037f40000 (usable) BIOS-e820: 0000000037f40000 - 0000000037f4d000 (ACPI data) BIOS-e820: 0000000037f4d000 - 0000000037f4e000 (ACPI NVS) BIOS-e820: 0000000037f4e000 - 0000000040000000 (reserved) BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 895MB LOWMEM available. found SMP MP-table at [c00f75e0] 000f75e0 Entering add_active_range(0, 0, 229184) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 229184 HighMem 229184 -> 229184 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 229184 On node 0 totalpages: 229184 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 1759 pages used for memmap Normal zone: 223329 pages, LIFO batch:31 HighMem zone: 0 pages used for memmap Movable zone: 0 pages used for memmap DMI present. ACPI: RSDP 000F75B0, 0024 (r2 PTLTD ) ACPI: XSDT 37F45097, 007C (r1 FSC PC 60000 LTP 0) ACPI: FACP 37F4C7FA, 00F4 (r3 FSC 60000 PTL_ F4240) ACPI: DSDT 37F45113, 7673 (r1 FSC D2721/A1 60000 MSFT 3000001) ACPI: FACS 37F4DFC0, 0040 ACPI: TCPA 37F4C8EE, 0032 (r1 Phoeni x 60000 TL 0) ACPI: WDAT 37F4C920, 0104 (r1 PTLTD WDATTBL 60000 LTP 1) ACPI: SSDT 37F4CA24, 0248 (r1 AMD POWERNOW 60000 AMD 1) ACPI: SRAT 37F4CC6C, 00A0 (r1 AMD HAMMER 60000 AMD 1) ACPI: ASF! 37F4CD0C, 0070 (r32 OEMID OEMTBL 60000 PTL 1) ACPI: SLIC 37F4CD7C, 0176 (r1 FSC PC 60000 LTP 0) ACPI: MCFG 37F4CEF2, 003C (r1 PTLTD MCFG 60000 LTP 0) ACPI: HPET 37F4CF2E, 0038 (r1 PTLTD HPETTBL 60000 LTP 1) ACPI: APIC 37F4CF66, 0072 (r1 PTLTD APIC 60000 LTP 0) ACPI: BOOT 37F4CFD8, 0028 (r1 PTLTD $SBFTBL$ 60000 LTP 1) ACPI: DMI detected: Fujitsu Siemens Detected use of extended apic ids on hypertransport bus ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs ACPI: HPET id: 0x10de8201 base: 0xfed00000 Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 50000000 (gap: 40000000:b8000000) SMP: Allowing 2 CPUs, 0 hotplug CPUs PERCPU: Allocating 36392 bytes of per cpu data NR_CPUS: 32, nr_cpu_ids: 2 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 227393 Kernel command line: lang=de video=vesa:ywrap,mtrr pckey=4e6842c5129e7882c318378dde52fe2e service=192.168.1.14 vga=791 initrd=miniroot.gz reboot=b product=winxppro init=/etc/init quiet hn=evb ramdisk_size=185320 splash BOOT_IMAGE=install mapped APIC to ffffb000 (fee00000) mapped IOAPIC to ffffa000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Extended CMOS year: 2000 Detected 2300.065 MHz processor. spurious 8259A interrupt: IRQ7. Console: colour dummy device 80x25 console [tty0] enabled Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 841640k/916736k available (2127k kernel code, 74572k reserved, 758k data, 340k init, 0k highmem) virtual kernel memory layout: fixmap : 0xffe14000 - 0xfffff000 (1964 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) lowmem : 0xc0000000 - 0xf7f40000 ( 895 MB) .init : 0xc03d7000 - 0xc042c000 ( 340 kB) .data : 0xc0313e37 - 0xc03d1a20 ( 758 kB) .text : 0xc0100000 - 0xc0313e37 (2127 kB) Checking if this processor honours the WP bit even in supervisor mode...Ok. CPA: page pool initialized 1 of 1 pages preallocated hpet clockevent registered Calibrating delay using timer specific routine.. 4605.32 BogoMIPS (lpj=9210650) Mount-cache hash table entries: 512 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU 0(2) -> Core 0 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Checking 'hlt' instruction... OK. ACPI: Core revision 20080321 ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0 CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 4400+ stepping 02 APIC calibration not consistent with PM Timer: 349ms instead of 100ms APIC delta adjusted to PM-Timer: 357954 (1249981) Booting processor 1/1 ip 6000 Initializing CPU#1 Calibrating delay using timer specific routine.. 1317.37 BogoMIPS (lpj=2634740) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU 1(2) -> Core 1 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: AMD Athlon(tm) 64 X2 Dual Core Processor 4400+ stepping 02 Brought up 2 CPUs Total of 2 processors activated (5922.69 BogoMIPS). CPU0 attaching sched-domain: domain 0: span 0-1 groups: 0 1 CPU1 attaching sched-domain: domain 0: span 0-1 groups: 1 0 net_namespace: 200 bytes NET: Registered protocol family 16 EISA bus registered ACPI: bus type pci registered PCI: MCFG configuration 0: base f8000000 segment 0 buses 0 - 5 PCI: MCFG area at f8000000 reserved in E820 PCI: Using MMCONFIG for extended config space PCI: Using configuration type 1 for base access Setting up standard PCI resources ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled ACPI: (supports S0 S1 S3 S5) ACPI: Using IOAPIC for interrupt routing ACPI: Device [ECP] status [00000008]: functional but not present; setting present ACPI: Device [COM2] status [00000008]: functional but not present; setting present ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Transparent bridge - 0000:00:08.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEXA._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEXB._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEXL._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.IXVE._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 11 12 13 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 12 13 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 11 12 13 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 11 12 13 14 15) *0, disabled. ACPI: PCI Interrupt Link [LK0A] (IRQs 16 17 18 19 20 21 22 23) *11 ACPI: PCI Interrupt Link [LK0B] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK0C] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK0D] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK1A] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK1B] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK1C] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK1D] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK2A] (IRQs 16 17 18 19 20 21 22 23) *11 ACPI: PCI Interrupt Link [LK2B] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK2C] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK2D] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK3A] (IRQs 16 17 18 19 20 21 22 23) *11 ACPI: PCI Interrupt Link [LK3B] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK3C] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK3D] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK4A] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK4B] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK4C] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK4D] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK5A] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK5B] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK5C] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK5D] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK6A] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK6B] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK6C] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK6D] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK7A] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK7B] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK7C] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LK7D] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LKR0] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LKR1] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LKR2] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LKR3] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LKR4] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LKR5] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LKR6] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LKR7] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LNKI] (IRQs 16 17 18 19 20 21 22 23) *5 ACPI: PCI Interrupt Link [LNKJ] (IRQs 16 17 18 19 20 21 22 23) *10 ACPI: PCI Interrupt Link [LNKK] (IRQs 16 17 18 19 20 21 22 23) *11 ACPI: PCI Interrupt Link [LNKL] (IRQs 16 17 18 19 20 21 22 23) *11 ACPI: PCI Interrupt Link [LNKM] (IRQs 16 17 18 19 20 21 22 23) *11 ACPI: PCI Interrupt Link [LNKN] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LNKO] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LNKP] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LNKQ] (IRQs 16 17 18 19 20 21 22 23) *11 ACPI: PCI Interrupt Link [LNKR] (IRQs 16 17 18 19 20 21 22 23) *11 ACPI: PCI Interrupt Link [LNKS] (IRQs 16 17 18 19 20 21 22 23) *11 ACPI: PCI Interrupt Link [LNKT] (IRQs 16 17 18 19 20 21 22 23) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 15 devices ACPI: ACPI bus type pnp unregistered PnPBIOS: Disabled by ACPI PNP SCSI subsystem initialized PCI: Using ACPI for IRQ routing ACPI: RTC can wake from S4 system 00:01: ioport range 0x4d0-0x4d1 has been reserved system 00:01: ioport range 0x500-0x57f has been reserved system 00:01: ioport range 0x1000-0x10e7 has been reserved system 00:01: ioport range 0x1200-0x12fe has been reserved system 00:01: ioport range 0x1400-0x14fe has been reserved system 00:01: ioport range 0x1500-0x15fe has been reserved system 00:01: ioport range 0x1600-0x16fe has been reserved system 00:01: ioport range 0x1700-0x17fe has been reserved system 00:01: ioport range 0x1800-0x18fe has been reserved system 00:01: ioport range 0x1900-0x19fe has been reserved system 00:01: ioport range 0x1a00-0x1afe has been reserved system 00:01: ioport range 0x1c00-0x1cfe has been reserved system 00:01: ioport range 0xfe00-0xfe00 has been reserved system 00:01: ioport range 0xff00-0xff00 has been reserved system 00:01: iomem range 0xf8000000-0xfbffffff could not be reserved system 00:01: iomem range 0xfc000000-0xfebfffff has been reserved system 00:01: iomem range 0xfec00000-0xfec7ffff could not be reserved system 00:01: iomem range 0xfec80000-0xfecfffff has been reserved system 00:01: iomem range 0xfee00000-0xfeefffff could not be reserved system 00:01: iomem range 0xfef00000-0xfef7ffff has been reserved system 00:01: iomem range 0xfef80000-0xfeffffff has been reserved system 00:01: iomem range 0xfff00000-0xffffffff could not be reserved PM-Timer running at invalid rate: 349% of normal - aborting. PCI: Bridge: 0000:00:08.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Failed to allocate mem resource #6:20000@f0000000 for 0000:02:00.0 PCI: Bridge: 0000:00:0b.0 IO window: 4000-4fff MEM window: 0xdc000000-0xdcffffff PREFETCH window: 0x00000000de000000-0x00000000efffffff PCI: Bridge: 0000:00:10.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:12.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:13.0 IO window: disabled. MEM window: 0xdde00000-0xddefffff PREFETCH window: disabled. PCI: Setting latency timer of device 0000:00:08.0 to 64 PCI: Setting latency timer of device 0000:00:0b.0 to 64 ACPI: PCI Interrupt Link [LKR0] enabled at IRQ 23 ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LKR0] -> GSI 23 (level, high) -> IRQ 23 PCI: Setting latency timer of device 0000:00:10.0 to 64 ACPI: PCI Interrupt Link [LKR2] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LKR2] -> GSI 22 (level, high) -> IRQ 22 PCI: Setting latency timer of device 0000:00:12.0 to 64 ACPI: PCI Interrupt Link [LKR3] enabled at IRQ 21 ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [LKR3] -> GSI 21 (level, high) -> IRQ 21 PCI: Setting latency timer of device 0000:00:13.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered NET: Registered protocol family 1 checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 62994k freed Simple Boot Flag at 0x38 set to 0x1 audit: initializing netlink socket (disabled) type=2000 audit(1217245531.579:1): initialized Total HugeTLB memory allocated, 0 msgmni has been set to 1767 io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered (default) io scheduler cfq registered pci 0000:02:00.0: Boot video device PCI: Setting latency timer of device 0000:00:10.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:10.0:pcie00] PCI: Setting latency timer of device 0000:00:12.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:12.0:pcie00] PCI: Setting latency timer of device 0000:00:13.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:13.0:pcie00] vesafb: framebuffer at 0xdf000000, mapped to 0xf8880000, using 3072k, total 14336k vesafb: mode is 1024x768x16, linelength=2048, pages=1 vesafb: protected mode interface info at c000:b640 vesafb: pmi: set display start = c00cb6a3, set palette = c00cb6fe vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found FDC 0 is a post-1991 82077 brd: module loaded Loading iSCSI transport class v2.0-869. PNP: PS/2 Controller [PNP0303:KEYB,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice EISA: Probing bus 0 at eisa.0 Cannot allocate resource for EISA slot 1 Cannot allocate resource for EISA slot 3 Cannot allocate resource for EISA slot 4 EISA: Detected 0 cards. TCP cubic registered NET: Registered protocol family 15 Starting balanced_irq Using IPI No-Shortcut mode input: AT Translated Set 2 keyboard as /class/input/input0 RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem). Freeing unused kernel memory: 340k freed Failed to execute /etc/init. Attempting defaults... ACPI: ACPI0007:00 is registered as cooling_device0 ACPI: ACPI0007:01 is registered as cooling_device1 input: Power Button (FF) as /class/input/input1 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input2 ACPI: Power Button (CM) [PWRB] usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver ACPI: PCI Interrupt Link [LNKJ] enabled at IRQ 20 ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKJ] -> GSI 20 (level, high) -> IRQ 20 PCI: Setting latency timer of device 0000:00:02.0 to 64 ohci_hcd 0000:00:02.0: OHCI Host Controller ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:02.0: irq 20, io mem 0xddbf9000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected pci_hotplug: PCI Hot Plug PCI Core version: 0.5 No dock devices found. ACPI: PCI Interrupt Link [LNKR] enabled at IRQ 19 ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [LNKR] -> GSI 19 (level, high) -> IRQ 19 PCI: Setting latency timer of device 0000:00:04.0 to 64 ohci_hcd 0000:00:04.0: OHCI Host Controller ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:04.0: irq 19, io mem 0xddbf8000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 6 ports detected libata version 3.00 loaded. ACPI: PCI Interrupt Link [LNKI] enabled at IRQ 18 ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LNKI] -> GSI 18 (level, high) -> IRQ 18 PCI: Setting latency timer of device 0000:00:02.1 to 64 ehci_hcd 0000:00:02.1: EHCI Host Controller ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3 ehci_hcd 0000:00:02.1: debug port 1 PCI: cache line size of 64 is not supported by device 0000:00:02.1 ehci_hcd 0000:00:02.1: irq 18, io mem 0xddbf6c00 ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 6 ports detected ACPI: PCI Interrupt Link [LNKS] enabled at IRQ 17 ACPI: PCI Interrupt 0000:00:04.1[B] -> Link [LNKS] -> GSI 17 (level, high) -> IRQ 17 PCI: Setting latency timer of device 0000:00:04.1 to 64 ehci_hcd 0000:00:04.1: EHCI Host Controller ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 4 ehci_hcd 0000:00:04.1: debug port 1 PCI: cache line size of 64 is not supported by device 0000:00:04.1 ehci_hcd 0000:00:04.1: irq 17, io mem 0xddbf6800 ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 6 ports detected tpm_inf_pnp 00:02: Found TPM with ID IFX0102 PCI: Setting latency timer of device 0000:00:09.0 to 64 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 ahci 0000:00:09.0: version 3.0 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:0d: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial 00:0e: activated 00:0e: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A ahci 0000:00:09.0: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl IDE mode ahci 0000:00:09.0: flags: 64bit ncq sntf led clo pmp pio PCI: Setting latency timer of device 0000:00:09.0 to 64 ------------[ cut here ]------------ WARNING: at drivers/ata/libata-core.c:5697 ata_host_activate+0xf6/0x100 [libata]() Modules linked in: 8250_pnp 8250 serial_core tg3(+) serio_raw ahci(+) ata_generic tpm_infineon tpm tpm_bios pata_acpi libata shpchp dock pci_hotplug ehci_hcd ohci_hcd usbcore container thermal button processor evdev Pid: 1937, comm: modprobe Not tainted 2.6.26 #1 [<c012706f>] warn_on_slowpath+0x5f/0x90 [<c01213d5>] finish_task_switch+0x95/0xa0 [<c0108c22>] dma_alloc_coherent+0x122/0x2b0 [<c025e2c1>] devres_add+0x31/0x50 [<c025f94c>] dmam_alloc_coherent+0x6c/0x90 [<f8bd529f>] ahci_port_resume+0x5f/0x70 [ahci] [<c025e2c1>] devres_add+0x31/0x50 [<f8bf893d>] ata_host_start+0xed/0x170 [libata] [<c02055ca>] pci_bus_write_config_byte+0x5a/0x70 [<f8bfcda6>] ata_host_activate+0xf6/0x100 [libata] [<f8bd6899>] ahci_init_one+0x899/0xac0 [ahci] [<c0209a96>] pci_device_probe+0x56/0x80 [<c025c682>] driver_probe_device+0x82/0x180 [<c025c7ec>] __driver_attach+0x6c/0x70 [<c025bdbb>] bus_for_each_dev+0x3b/0x60 [<c025c506>] driver_attach+0x16/0x20 [<c025c780>] __driver_attach+0x0/0x70 [<c025c1e9>] bus_add_driver+0xa9/0x210 [<c02099e0>] pci_device_remove+0x0/0x40 [<c025c95d>] driver_register+0x4d/0x120 [<c0209cbd>] __pci_register_driver+0x3d/0x80 [<c0149194>] sys_init_module+0x84/0x1b0 [<c0103da1>] sysenter_past_esp+0x6a/0x99 ======================= ---[ end trace 21da9b6136ad63e5 ]--- scsi0 : ahci scsi1 : ahci scsi2 : ahci scsi3 : ahci scsi4 : ahci scsi5 : ahci ata1: SATA max UDMA/133 abar m8192@0xddbfa000 port 0xddbfa100 ata2: SATA max UDMA/133 abar m8192@0xddbfa000 port 0xddbfa180 ata3: SATA max UDMA/133 abar m8192@0xddbfa000 port 0xddbfa200 ata4: SATA max UDMA/133 abar m8192@0xddbfa000 port 0xddbfa280 ata5: SATA max UDMA/133 abar m8192@0xddbfa000 port 0xddbfa300 ata6: SATA max UDMA/133 abar m8192@0xddbfa000 port 0xddbfa380 ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: qc timeout (cmd 0xec) ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4) ata1: failed to recover some devices, retrying in 5 secs ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: qc timeout (cmd 0xec) ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4) ata1: failed to recover some devices, retrying in 5 secs ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: qc timeout (cmd 0xec) ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4) ata1: failed to recover some devices, retrying in 5 secs ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata2.00: qc timeout (cmd 0xec) ata2.00: failed to IDENTIFY (I/O error, err_mask=0x5) ata2: failed to recover some devices, retrying in 5 secs ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata2.00: qc timeout (cmd 0xec) ata2.00: failed to IDENTIFY (I/O error, err_mask=0x5) ata2: failed to recover some devices, retrying in 5 secs ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata2.00: qc timeout (cmd 0xec) ata2.00: failed to IDENTIFY (I/O error, err_mask=0x5) ata2: failed to recover some devices, retrying in 5 secs ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata3: SATA link down (SStatus 0 SControl 300) ata4: SATA link down (SStatus 0 SControl 300) ata5: SATA link down (SStatus 0 SControl 300) ata6: SATA link down (SStatus 0 SControl 300) tg3.c:v3.92.1 (June 9, 2008) ACPI: PCI Interrupt Link [LK3A] enabled at IRQ 16 ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [LK3A] -> GSI 16 (level, high) -> IRQ 16 PCI: Setting latency timer of device 0000:05:00.0 to 64 eth0: Tigon3 [partno(BCM95787) rev b002 PHY(5787)] (PCI Express) 10/100/1000Base-T Ethernet 00:19:99:23:e4:7d eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1] eth0: dma_rwctrl[76180000] dma_mask[64-bit] fuse init (API version 7.9) device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com NET: Registered protocol family 17 tg3: eth0: Link is up at 100 Mbps, full duplex. tg3: eth0: Flow control is on for TX and on for RX. tg3: eth0: Link is up at 100 Mbps, full duplex. tg3: eth0: Flow control is on for TX and on for RX.
Any help?
-- Jan Schneider
uib gmbh Bonifaziusplatz 1B 55118 Mainz
Tel. 06131 / 27561-20 Fax 06131 / 27561-22
E-Mail: j.schneider@uib.de
Internet: www.uib.de
Geschäftsführer: dr. detlef oertel Handelsregister: Amtsgericht Mainz HRB 6942 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |