lkml.org 
[lkml]   [2008]   [May]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] md: fix raid5 'repair' operations
Date
commit bd2ab67030e9116f1e4aae1289220255412b37fd "md: close a livelock
window in handle_parity_checks5" introduced a bug in handling 'repair'
operations. After a repair operation completes we clear the state bits
tracking this operation. However, they are cleared too early and this
results in the code deciding to re-run the parity check operation. Since
we have done the repair in memory the second check does not find a mismatch
and thus does not do a writeback.

Test results:
$ echo repair > /sys/block/md0/md/sync_action
$ cat /sys/block/md0/md/mismatch_cnt
51072
$ echo repair > /sys/block/md0/md/sync_action
$ cat /sys/block/md0/md/mismatch_cnt
0

(also fix incorrect indentation)

Cc: <stable@kernel.org>
Tested-by: George Spelvin <linux@horizon.com>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
---

drivers/md/raid5.c | 25 +++++++++++++------------
1 files changed, 13 insertions(+), 12 deletions(-)


diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c
index 087eee0..ee0ea91 100644
--- a/drivers/md/raid5.c
+++ b/drivers/md/raid5.c
@@ -2369,8 +2369,8 @@ static void handle_parity_checks5(raid5_conf_t *conf, struct stripe_head *sh,

/* complete a check operation */
if (test_and_clear_bit(STRIPE_OP_CHECK, &sh->ops.complete)) {
- clear_bit(STRIPE_OP_CHECK, &sh->ops.ack);
- clear_bit(STRIPE_OP_CHECK, &sh->ops.pending);
+ clear_bit(STRIPE_OP_CHECK, &sh->ops.ack);
+ clear_bit(STRIPE_OP_CHECK, &sh->ops.pending);
if (s->failed == 0) {
if (sh->ops.zero_sum_result == 0)
/* parity is correct (on disc,
@@ -2400,16 +2400,6 @@ static void handle_parity_checks5(raid5_conf_t *conf, struct stripe_head *sh,
canceled_check = 1; /* STRIPE_INSYNC is not set */
}

- /* check if we can clear a parity disk reconstruct */
- if (test_bit(STRIPE_OP_COMPUTE_BLK, &sh->ops.complete) &&
- test_bit(STRIPE_OP_MOD_REPAIR_PD, &sh->ops.pending)) {
-
- clear_bit(STRIPE_OP_MOD_REPAIR_PD, &sh->ops.pending);
- clear_bit(STRIPE_OP_COMPUTE_BLK, &sh->ops.complete);
- clear_bit(STRIPE_OP_COMPUTE_BLK, &sh->ops.ack);
- clear_bit(STRIPE_OP_COMPUTE_BLK, &sh->ops.pending);
- }
-
/* start a new check operation if there are no failures, the stripe is
* not insync, and a repair is not in flight
*/
@@ -2424,6 +2414,17 @@ static void handle_parity_checks5(raid5_conf_t *conf, struct stripe_head *sh,
}
}

+ /* check if we can clear a parity disk reconstruct */
+ if (test_bit(STRIPE_OP_COMPUTE_BLK, &sh->ops.complete) &&
+ test_bit(STRIPE_OP_MOD_REPAIR_PD, &sh->ops.pending)) {
+
+ clear_bit(STRIPE_OP_MOD_REPAIR_PD, &sh->ops.pending);
+ clear_bit(STRIPE_OP_COMPUTE_BLK, &sh->ops.complete);
+ clear_bit(STRIPE_OP_COMPUTE_BLK, &sh->ops.ack);
+ clear_bit(STRIPE_OP_COMPUTE_BLK, &sh->ops.pending);
+ }
+
+
/* Wait for check parity and compute block operations to complete
* before write-back. If a failure occurred while the check operation
* was in flight we need to cycle this stripe through handle_stripe


\
 
 \ /
  Last update: 2008-05-02 23:29    [W:0.027 / U:0.816 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site