lkml.org 
[lkml]   [2008]   [May]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: Bad value with w83627thf
Hi Jean!

sorry for the bad ML.

the battery is CR2032, and it is 3V, im older kernel alway reported
bad value 0,02V or 2,4V (i think it is a possible value), after i
inserted new battery, show 2,4V.
from the 2.6.26-rcX kernel showed the 3+ V. when i reboot to older
kernel, the this state remained, but when turned off the pc, then not.


On 5/16/08, Jean Delvare <khali@linux-fr.org> wrote:
> Hi Oliver,
>
> You are writing to the wrong mailing list (i2c instead of lm-sensors)
> so I am redirecting.
>
> On Fri, 16 May 2008 14:59:21 +0200, Oliver Pinter wrote:
>> linux-2.6 - git HEAD on: 9662369
>> lm-sensors: 1:3.0.1-5
>> libsensors4: 1:3.0.1-5
>> os: debian lenny
>> sernsor: w83627thf on asus p4c800 MB
>>
>> with 2.6.26-rcX kernel, reported false Battery values,
>> -------------------------------------->
>> VBat: +3.26 V (min = +0.02 V, max = +3.01 V) ALARM
>> <-------------------------------------
>
> There is nothing wrong here. +3.26V sounds possible and correct for the
> battery voltage. If you are worried about the min and max values: it is
> up to you to edit your sensors3.conf file to set them properly if the
> BIOS of your motherboard did not (apply the changes with "sensors -s").
> The alarm will go away when you do.
>
>> lspci -xxx
>> 00:1f.3 SMBus: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus
>> Controller (rev 02)
>> 00: 86 80 d3 24 01 00 80 02 02 00 05 0c 00 00 00 00
>> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>> 20: 01 04 00 00 00 00 00 00 00 00 00 00 43 10 a6 80
>> 30: 00 00 00 00 00 00 00 00 00 00 00 00 03 02 00 00
>> 40: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>> f0: 00 00 00 00 00 00 00 00 66 0f 04 00 00 00 00 00
>
> Completely irrelevant here, the Winbond W83627THF is an LPC chip, it
> doesn't have an I2C/SMBus interface, so the SMBus controller doesn't
> matter at all.
>
> --
> Jean Delvare
>


--
Thanks,
Oliver


\
 
 \ /
  Last update: 2008-05-16 15:47    [W:0.048 / U:0.736 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site