lkml.org 
[lkml]   [2008]   [Mar]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    SubjectRe: BUG: High resolution timer/dynticks bug
    On Sun, Mar 09, 2008 at 08:42:21PM +0100, Thomas Gleixner wrote:
    > On Sun, 9 Mar 2008, Diego Woitasen wrote:
    > > On Sun, Mar 09, 2008 at 04:42:05PM +0100, Thomas Gleixner wrote:
    > > > On Sat, 8 Mar 2008, Diego Woitasen wrote:
    > > > > >
    > > > > > Is the problem reproducible when you add "hpet=disable" to the kernel
    > > > > > command line ?
    > > > >
    > > > > No, with hpet=disable works fine.
    > > >
    > > > Can you please try "processor.max_cstate=2" on the kernel command line ?
    > > >
    > > > Also please provide a full boot log and the output of lspci -vvv
    > > >
    > > > Thanks,
    > > >
    > > > tglx
    > >
    > > I tried. Same results, freezes after few minutes.
    > >
    > > ----------------dmesg:
    >
    > > Unknown boot option `processor.max_cstate=2': ignoring
    >
    > Hmm. That probably does not work when the ACPI processor stuff is
    > compiled as module. Can you please compile that in via
    > CONFIG_ACPI_PROCESSOR=y ?
    >
    > Thanks,
    > tglx

    I change the configuration and then boot with "processor.max_cstate=2",
    but the system freezes again.

    dmesg updated:

    Linux version 2.6.25-rc4-porti-funca-00134-g84c6f60 (diegows@porti) (gcc version 4.2.3 (Debian 4.2.3-1)) #42 PREEMPT Sun Mar 9 18:45:00 ARST 2008
    Command line: root=/dev/sda2 ro nmi_watchdog=2 netconsole=4444@192.168.1.101/eth0,5555@192.168.1.10/00:0e:a6:b1:7e:92 processor.max_cstate=2
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
    BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000d2000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000001df10000 (usable)
    BIOS-e820: 000000001df10000 - 000000001df18000 (ACPI data)
    BIOS-e820: 000000001df18000 - 000000001df80000 (ACPI NVS)
    BIOS-e820: 000000001df80000 - 0000000020000000 (reserved)
    BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
    BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
    BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
    BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
    BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
    Entering add_active_range(0, 0, 157) 0 entries of 256 used
    Entering add_active_range(0, 256, 122640) 1 entries of 256 used
    end_pfn_map = 1048576
    DMI present.
    ACPI: RSDP 000F87B0, 0024 (r3 HPQOEM)
    ACPI: XSDT 1DF11044, 005C (r1 HPQOEM SLIC-MPC 6040000 LTP 0)
    ACPI: FACP 1DF17B21, 00F4 (r3 HPQOEM SLIC-MPC 6040000 PTL F4240)
    ACPI: DSDT 1DF110A0, 6A81 (r1 HPQOEM SLIC-MPC 6040000 MSFT 100000E)
    ACPI: FACS 1DF18FC0, 0040
    ACPI: SLIC 1DF17C89, 0176 (r1 HPQOEM SLIC-MPC 6040000 HPQ 1)
    ACPI: MCFG 1DF17DFF, 003C (r1 HPQOEM SLIC-MPC 6040000 LTP 0)
    ACPI: HPET 1DF17E3B, 0038 (r1 HPQOEM SLIC-MPC 6040000 LTP 1)
    ACPI: APIC 1DF17E73, 0050 (r1 HPQOEM SLIC-MPC 6040000 LTP 0)
    ACPI: BOOT 1DF17EC3, 0028 (r1 HPQOEM SLIC-MPC 6040000 LTP 1)
    ACPI: SSDT 1DF17EEB, 0115 (r1 HPQOEM SLIC-MPC 6040000 LTP 1)
    ACPI: DMI detected: Hewlett-Packard
    Entering add_active_range(0, 0, 157) 0 entries of 256 used
    Entering add_active_range(0, 256, 122640) 1 entries of 256 used
    early res: 0 [0-fff] BIOS data page
    early res: 1 [200000-688a07] TEXT DATA BSS
    early res: 2 [9dc00-9fbff] EBDA
    early res: 3 [8000-afff] PGTABLE
    [ffffe20000000000-ffffe200001fffff] PMD ->ffff810001200000 on node 0
    [ffffe20000200000-ffffe200003fffff] PMD ->ffff810001600000 on node 0
    [ffffe20000400000-ffffe200005fffff] PMD ->ffff810001a00000 on node 0
    [ffffe20000600000-ffffe200007fffff] PMD ->ffff810001e00000 on node 0
    Zone PFN ranges:
    DMA 0 -> 4096
    DMA32 4096 -> 1048576
    Normal 1048576 -> 1048576
    Movable zone start PFN for each node
    early_node_map[2] active PFN ranges
    0: 0 -> 157
    0: 256 -> 122640
    On node 0 totalpages: 122541
    DMA zone: 56 pages used for memmap
    DMA zone: 1168 pages reserved
    DMA zone: 2773 pages, LIFO batch:0
    DMA32 zone: 1620 pages used for memmap
    DMA32 zone: 116924 pages, LIFO batch:31
    Normal zone: 0 pages used for memmap
    Movable zone: 0 pages used for memmap
    Detected use of extended apic ids on hypertransport bus
    ACPI: PM-Timer IO Port: 0x1008
    ACPI: Local APIC address 0xfee00000
    ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    Processor #0 (Bootup-CPU)
    ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
    ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
    IOAPIC[0]: apic_id 1, address 0xfec00000, GSI 0-23
    ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    ACPI: IRQ0 used by override.
    ACPI: IRQ2 used by override.
    ACPI: IRQ9 used by override.
    Setting APIC routing to flat
    ACPI: HPET id: 0x10de8201 base: 0xfed00000
    Using ACPI (MADT) for SMP configuration information
    PM: Registered nosave memory: 000000000009d000 - 000000000009e000
    PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
    PM: Registered nosave memory: 00000000000a0000 - 00000000000d2000
    PM: Registered nosave memory: 00000000000d2000 - 0000000000100000
    Allocating PCI resources starting at 30000000 (gap: 20000000:c0000000)
    Built 1 zonelists in Zone order, mobility grouping on. Total pages: 119697
    Kernel command line: root=/dev/sda2 ro nmi_watchdog=2 netconsole=4444@192.168.1.101/eth0,5555@192.168.1.10/00:0e:a6:b1:7e:92 processor.max_cstate=2
    Initializing CPU#0
    PID hash table entries: 2048 (order: 11, 16384 bytes)
    Extended CMOS year: 2000
    TSC calibrated against PM_TIMER
    time.c: Detected 2009.145 MHz processor.
    spurious 8259A interrupt: IRQ7.
    Console: colour VGA+ 80x25
    console [tty0] enabled
    Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
    Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
    Checking aperture...
    Node 0: aperture @ b1f8000000 size 32 MB
    Aperture beyond 4GB. Ignoring.
    No AGP bridge found
    Memory: 475804k/490560k available (3008k kernel code, 13704k reserved, 1073k data, 204k init)
    CPA: page pool initialized 1 of 1 pages preallocated
    SLUB: Genslabs=12, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
    hpet clockevent registered
    Calibrating delay using timer specific routine.. 4020.77 BogoMIPS (lpj=2010389)
    Mount-cache hash table entries: 256
    CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
    CPU: L2 Cache: 512K (64 bytes/line)
    CPU: AMD Turion(tm) 64 stepping 02
    ACPI: Core revision 20070126
    Using local APIC timer interrupts.
    APIC timer calibration result 12557155
    Detected 12.557 MHz APIC timer.
    Testing NMI watchdog ... OK.
    net_namespace: 872 bytes
    NET: Registered protocol family 16
    ACPI: bus type pci registered
    PCI: Using MMCONFIG at e0000000 - e02fffff
    PCI: Using configuration type 1
    ACPI: EC: Look up EC in DSDT
    ACPI: BIOS _OSI(Linux) query ignored via DMI
    ACPI: Interpreter enabled
    ACPI: (supports S0 S3 S4 S5)
    ACPI: Using IOAPIC for interrupt routing
    ACPI: EC: non-query interrupt received, switching to interrupt mode
    ACPI: EC: GPE = 0x1, I/O: command/status = 0x66, data = 0x62
    ACPI: EC: driver started in interrupt mode
    ACPI: PCI Root Bridge [PCI0] (0000:00)
    PCI: Transparent bridge - 0000:00:10.0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR1._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR2._PRT]
    ACPI: PCI Interrupt Link [LNK1] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LNK2] (IRQs 16 17 18 19 20 21 22 23) *10
    ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 *10 11 14 15)
    ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 10 11 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LK1E] (IRQs 20) *0, disabled.
    ACPI: PCI Interrupt Link [LK2E] (IRQs 19) *11
    ACPI: PCI Interrupt Link [LK3E] (IRQs 21) *10
    ACPI: PCI Interrupt Link [LK4E] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LSMB] (IRQs 16 17 18 19 20 21 22 23) *10
    ACPI: PCI Interrupt Link [LSMU] (IRQs 16 17 18 19 20 21 22 23) *11
    ACPI: PCI Interrupt Link [LUS0] (IRQs 16 17 18 19 20 21 22 23) *11
    ACPI: PCI Interrupt Link [LUS2] (IRQs 16 17 18 19 20 21 22 23) *7
    ACPI: PCI Interrupt Link [LMAC] (IRQs 16 17 18 19 20 21 22 23) *11
    ACPI: PCI Interrupt Link [LAZA] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LACI] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LMCI] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LPID] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
    ACPI: PCI Interrupt Link [LTID] (IRQs 16 17 18 19 20 21 22 23) *5
    ACPI: PCI Interrupt Link [LSI1] (IRQs 16 17 18 19 20 21 22 23) *0
    Linux Plug and Play Support v0.97 (c) Adam Belay
    pnp: PnP ACPI init
    ACPI: bus type pnp registered
    pnp: PnP ACPI: found 11 devices
    ACPI: ACPI bus type pnp unregistered
    SCSI subsystem initialized
    libata version 3.00 loaded.
    PCI: Using ACPI for IRQ routing
    PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
    hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
    hpet0: 3 32-bit timers, 25000000 Hz
    Time: tsc clocksource has been installed.
    system 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
    system 00:02: ioport range 0x1000-0x107f has been reserved
    system 00:02: ioport range 0x1080-0x10ff has been reserved
    system 00:02: ioport range 0x1400-0x147f has been reserved
    system 00:02: ioport range 0x1480-0x14ff has been reserved
    system 00:02: ioport range 0x1800-0x187f has been reserved
    system 00:02: ioport range 0x1880-0x18ff has been reserved
    system 00:02: ioport range 0x2000-0x203f has been reserved
    system 00:03: ioport range 0x360-0x361 has been reserved
    system 00:03: ioport range 0x4d0-0x4d1 has been reserved
    PCI: Bridge: 0000:00:02.0
    IO window: disabled.
    MEM window: 0xc3000000-0xc30fffff
    PREFETCH window: disabled.
    PCI: Bridge: 0000:00:03.0
    IO window: 4000-4fff
    MEM window: 0xc8000000-0xc87fffff
    PREFETCH window: disabled.
    PCI: Bridge: 0000:00:10.0
    IO window: disabled.
    MEM window: 0xc3100000-0xc31fffff
    PREFETCH window: disabled.
    PCI: Setting latency timer of device 0000:00:02.0 to 64
    PCI: Setting latency timer of device 0000:00:03.0 to 64
    PCI: Setting latency timer of device 0000:00:10.0 to 64
    NET: Registered protocol family 2
    IP route cache hash table entries: 4096 (order: 3, 32768 bytes)
    TCP established hash table entries: 16384 (order: 6, 262144 bytes)
    TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
    TCP: Hash tables configured (established 16384 bind 16384)
    TCP reno registered
    Simple Boot Flag at 0x36 set to 0x1
    Total HugeTLB memory allocated, 0
    SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
    SGI XFS Quota Management subsystem
    io scheduler noop registered
    io scheduler cfq registered (default)
    pci 0000:00:00.0: Enabling HT MSI Mapping
    pci 0000:00:02.0: Enabling HT MSI Mapping
    pci 0000:00:03.0: Enabling HT MSI Mapping
    pci 0000:00:05.0: Boot video device
    pci 0000:00:09.0: Enabling HT MSI Mapping
    pci 0000:00:0e.0: Enabling HT MSI Mapping
    pci 0000:00:10.0: Enabling HT MSI Mapping
    pci 0000:00:10.1: Enabling HT MSI Mapping
    PCI: Setting latency timer of device 0000:00:02.0 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[0000:00:02.0:pcie00]
    Allocate Port Service[0000:00:02.0:pcie03]
    PCI: Setting latency timer of device 0000:00:03.0 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[0000:00:03.0:pcie00]
    Allocate Port Service[0000:00:03.0:pcie03]
    ACPI: AC Adapter [ADP1] (on-line)
    ACPI: Battery Slot [BAT0] (battery present)
    input: Power Button (FF) as /class/input/input0
    ACPI: Power Button (FF) [PWRF]
    input: Lid Switch as /class/input/input1
    ACPI: Lid Switch [LID0]
    input: Sleep Button (CM) as /class/input/input2
    ACPI: Sleep Button (CM) [SLPB]
    input: Power Button (CM) as /class/input/input3
    ACPI: Power Button (CM) [PWRB]
    ACPI: processor limited to max C-state 2
    ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
    ACPI: ACPI0007:00 is registered as cooling_device0
    ACPI: Processor [CPU0] (supports 8 throttling states)
    ACPI: LNXTHERM:01 is registered as thermal_zone0
    ACPI: Thermal Zone [TZS0] (58 C)
    ACPI: LNXTHERM:02 is registered as thermal_zone1
    ACPI: Thermal Zone [TZS1] (61 C)
    Real Time Clock Driver v1.12ac
    hpet_resources: 0xfed00000 is busy
    Non-volatile memory driver v1.2
    Linux agpgart interface v0.103
    forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
    ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 23
    ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LMAC] -> GSI 23 (level, high) -> IRQ 23
    PCI: Setting latency timer of device 0000:00:14.0 to 64
    Switched to high resolution mode on CPU 0
    forcedeth 0000:00:14.0: ifname eth0, PHY OUI 0x5043 @ 1, addr 00:16:d3:91:30:79
    forcedeth 0000:00:14.0: highdma pwrctl timirq lnktim desc-v3
    netconsole: local port 4444
    netconsole: local IP 192.168.1.101
    netconsole: interface eth0
    netconsole: remote port 5555
    netconsole: remote IP 192.168.1.10
    netconsole: remote ethernet address 00:0e:a6:b1:7e:92
    netconsole: device eth0 not up yet, forcing it
    eth0: no link during initialization.
    netconsole: timeout waiting for carrier
    console [netcon0] enabled
    netconsole: network logging started
    Uniform Multi-Platform E-IDE driver
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    NFORCE-MCP51: 0000:00:0d.0 (rev f1) UDMA133 controller
    NFORCE-MCP51: IDE controller (0x10de:0x0265 rev 0xf1) at PCI slot 0000:00:0d.0
    NFORCE-MCP51: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x3080-0x3087, BIOS settings: hda:PIO, hdb:PIO
    ide1: BM-DMA at 0x3088-0x308f, BIOS settings: hdc:PIO, hdd:PIO
    Probing IDE interface ide0...
    Probing IDE interface ide1...
    hdc: Slimtype DVD A DS8AZH, ATAPI CD/DVD-ROM drive
    hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
    hdc: MWDMA2 mode selected
    ide1 at 0x170-0x177,0x376 on irq 15
    isa bounce pool size: 16 pages
    Probing IDE interface ide0...
    hdc: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
    Uniform CD-ROM driver Revision: 3.20
    Driver 'sd' needs updating - please use bus_type methods
    sata_nv 0000:00:0e.0: version 3.5
    PCI: Enabling device 0000:00:0e.0 (0005 -> 0007)
    ACPI: PCI Interrupt Link [LTID] enabled at IRQ 22
    ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [LTID] -> GSI 22 (level, high) -> IRQ 22
    PCI: Setting latency timer of device 0000:00:0e.0 to 64
    scsi0 : sata_nv
    scsi1 : sata_nv
    ata1: SATA max UDMA/133 cmd 0x30b0 ctl 0x30a4 bmdma 0x3090 irq 22
    ata2: SATA max UDMA/133 cmd 0x30a8 ctl 0x30a0 bmdma 0x3098 irq 22
    ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    ata1.00: ATA-7: WDC WD1200BEVS-60LAT0, 01.06M01, max UDMA/100
    ata1.00: 234441648 sectors, multi 16: LBA48
    ata1.00: configured for UDMA/100
    ata2: SATA link down (SStatus 0 SControl 300)
    scsi 0:0:0:0: Direct-Access ATA WDC WD1200BEVS-6 01.0 PQ: 0 ANSI: 5
    sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
    sd 0:0:0:0: [sda] Write Protect is off
    sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
    sd 0:0:0:0: [sda] Write Protect is off
    sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sda: sda1 sda2 sda3 < sda5 sda6 sda7 sda8 >
    sd 0:0:0:0: [sda] Attached SCSI disk
    sd 0:0:0:0: Attached scsi generic sg0 type 0
    PNP: PS/2 Controller [PNP0303:KBD0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
    i8042.c: Detected active multiplexing controller, rev 1.1.
    serio: i8042 KBD port at 0x60,0x64 irq 1
    serio: i8042 AUX0 port at 0x60,0x64 irq 12
    serio: i8042 AUX1 port at 0x60,0x64 irq 12
    serio: i8042 AUX2 port at 0x60,0x64 irq 12
    serio: i8042 AUX3 port at 0x60,0x64 irq 12
    mice: PS/2 mouse device common for all mice
    cpuidle: using governor ladder
    input: AT Translated Set 2 keyboard as /class/input/input4
    cpuidle: using governor menu
    IPVS: Registered protocols ()
    IPVS: Connection hash table configured (size=4096, memory=64Kbytes)
    IPVS: ipvs loaded.
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    can: controller area network core (rev 20071116 abi 8)
    NET: Registered protocol family 29
    powernow-k8: Found 1 AMD Turion(tm) 64 processors (1 cpu cores) (version 2.20.00)
    powernow-k8: 0 : fid 0xc (2000 MHz), vid 0xe
    powernow-k8: 1 : fid 0xa (1800 MHz), vid 0x10
    powernow-k8: 2 : fid 0x8 (1600 MHz), vid 0x12
    powernow-k8: 3 : fid 0x0 (800 MHz), vid 0x18
    XFS mounting filesystem sda2
    Starting XFS recovery on filesystem: sda2 (logdev: internal)
    Ending XFS recovery on filesystem: sda2 (logdev: internal)
    VFS: Mounted root (xfs filesystem) readonly.
    Freeing unused kernel memory: 204k freed
    ACPI: PCI Interrupt Link [LK2E] enabled at IRQ 19
    ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LK2E] -> GSI 19 (level, high) -> IRQ 19
    PCI: Setting latency timer of device 0000:01:00.0 to 64
    ssb: Sonics Silicon Backplane found on PCI device 0000:01:00.0
    i2c-adapter i2c-0: nForce2 SMBus adapter at 0x3040
    i2c-adapter i2c-1: nForce2 SMBus adapter at 0x3000
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
    ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 21
    ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LUS0] -> GSI 21 (level, high) -> IRQ 21
    PCI: Setting latency timer of device 0000:00:0b.0 to 64
    ohci_hcd 0000:00:0b.0: OHCI Host Controller
    ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1
    ohci_hcd 0000:00:0b.0: irq 21, io mem 0xc0004000
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 8 ports detected
    ieee80211_crypt: registered algorithm 'NULL'
    ieee80211: 802.11 data/management/control stack, git-1.1.13
    ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
    usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
    usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    usb usb1: Product: OHCI Host Controller
    usb usb1: Manufacturer: Linux 2.6.25-rc4-porti-funca-00134-g84c6f60 ohci_hcd
    usb usb1: SerialNumber: 0000:00:0b.0
    ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 20
    ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [LUS2] -> GSI 20 (level, high) -> IRQ 20
    PCI: Setting latency timer of device 0000:00:0b.1 to 64
    ehci_hcd 0000:00:0b.1: EHCI Host Controller
    ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
    ehci_hcd 0000:00:0b.1: debug port 1
    PCI: cache line size of 64 is not supported by device 0000:00:0b.1
    ehci_hcd 0000:00:0b.1: irq 20, io mem 0xc0005000
    ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 8 ports detected
    bcm43xx driver
    usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
    usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    usb usb2: Product: EHCI Host Controller
    usb usb2: Manufacturer: Linux 2.6.25-rc4-porti-funca-00134-g84c6f60 ehci_hcd
    usb usb2: SerialNumber: 0000:00:0b.1
    ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 18
    ACPI: PCI Interrupt 0000:03:09.0[A] -> Link [LNK1] -> GSI 18 (level, high) -> IRQ 18
    sdhci: Secure Digital Host Controller Interface driver
    sdhci: Copyright(c) Pierre Ossman
    ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[c3100000-c31007ff] Max Packet=[2048] IR/IT contexts=[4/4]
    sdhci: SDHCI controller found at 0000:03:09.1 [1180:0822] (rev 19)
    ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 17
    ACPI: PCI Interrupt 0000:03:09.1[B] -> Link [LNK2] -> GSI 17 (level, high) -> IRQ 17
    sdhc0:slot0: Will use DMA mode even though HW doesn't fully claim to support it.
    mmc0: SDHCI at 0xc3100800 irq 17 DMA
    ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 16
    ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LAZA] -> GSI 16 (level, high) -> IRQ 16
    PCI: Setting latency timer of device 0000:00:10.1 to 64
    b43-phy0: Broadcom 4311 WLAN found
    phy0: Selected rate control algorithm 'pid'
    input: ImPS/2 Synaptics TouchPad as /class/input/input5
    Broadcom 43xx driver loaded [ Features: P, Firmware-ID: FW13 ]
    ieee1394: Host added: ID:BUS[0-00:1023] GUID[07e40a00f6cb5006]
    Adding 987956k swap on /dev/sda5. Priority:-1 extents:1 across:987956k
    loop: module loaded
    device-mapper: uevent: version 1.0.3
    device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
    Ebtables v2.0 registered
    Bridge firewalling registered
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on sda1, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    Filesystem "dm-0": Disabling barriers, not supported by the underlying device
    XFS mounting filesystem dm-0
    Starting XFS recovery on filesystem: dm-0 (logdev: internal)
    Ending XFS recovery on filesystem: dm-0 (logdev: internal)
    Filesystem "dm-1": Disabling barriers, not supported by the underlying device
    XFS mounting filesystem dm-1
    Ending clean XFS mount for filesystem: dm-1
    EXT3-fs: mounted filesystem with ordered data mode.
    kjournald starting. Commit interval 5 seconds
    Marking TSC unstable due to TSC halts in idle
    Time: hpet clocksource has been installed.
    atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    atkbd.c: Unknown key released (translated set 2, code 0xd9 on isa0060/serio0).
    atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
    b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
    wlan0: Initial auth_alg=0
    wlan0: authenticate with AP 00:e0:4c:fe:41:e1
    wlan0: RX authentication from 00:e0:4c:fe:41:e1 (alg=0 transaction=2 status=0)
    wlan0: authenticated
    wlan0: associate with AP 00:e0:4c:fe:41:e1
    wlan0: RX AssocResp from 00:e0:4c:fe:41:e1 (capab=0x411 status=0 aid=193)
    wlan0: invalid aid value 193; bits 15:14 not set
    wlan0: associated
    wlan0: switched to long barker preamble (BSSID=00:e0:4c:fe:41:e1)
    TCP veno registered
    --

    --------------
    Diego Woitasen


    \
     
     \ /
      Last update: 2008-03-09 23:01    [W:0.051 / U:125.240 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site