lkml.org 
[lkml]   [2008]   [Mar]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 1/2 v4] Driver for Freescale 8610 and 5121 DIU
Date
The following features are supported:
plane 0 works as a regular frame buffer, can be accessed by /dev/fb0
plane 1 has two AOIs (area of interest), can be accessed by /dev/fb1 and /dev/fb2
plane 2 has two AOIs, can be accessed by /dev/fb3 and /dev/fb4
Special ioctls support AOIs

All /dev/fb* can be used as regular frame buffer devices, except hardware change can
only be made through /dev/fb0. Changing pixel clock has no effect on other fbs.

Limitation of usage of AOIs:
AOIs on the same plane can not be horizonally overlapped
AOIs have horizonal order, i.e. AOI0 should be always on top of AOI1
AOIs can not beyond phisical display area. Application should check AOI geometry
before changing physical resolution on /dev/fb0

required command line parameters to preallocate memory for frame buffer
diufb=15M

optional command line parameters to set modes and monitor
video=fslfb:[resolution][,bpp][,monitor]
Syntax:

Resolution
xres x yres-bpp@refresh_rate, the -bpp and @refresh_rate are optional
eg, 1024x768, 1280x1024, 1280x1024-32, 1280x1024@60, 1280x1024-32@60, 1280x480-32@60

Bpp
bpp=32, bpp=24, or bpp=16

Monitor
monitor=0, monitor=1, monitor=2
0 is DVI
1 is Single link LVDS
2 is Double link LVDS

Note: switching monitor is a board feather, not DIU feather. MPC8610HPCD has three
monitor ports to swtich to. MPC5121ADS doesn't have additional monitor port. So switching
monirot port for MPC5121ADS has no effect.

If compiled as a module, it takes pamameters mode, bpp, monitor with the same syntax above.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
---
This patch addes new feature of Freescale Display Unit framebuffer driver, targeting 2.6.26 kernel.
Documentation/powerpc/booting-without-of.txt | 33 +
arch/powerpc/boot/dts/mpc8610_hpcd.dts | 12 +
drivers/video/Kconfig | 10 +
drivers/video/Makefile | 1 +
drivers/video/fsl-diu-fb.c | 1741 ++++++++++++++++++++++++++
drivers/video/fsl-diu-fb.h | 223 ++++
6 files changed, 2020 insertions(+), 0 deletions(-)
create mode 100644 drivers/video/fsl-diu-fb.c
create mode 100644 drivers/video/fsl-diu-fb.h
diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt
index 7b4e8a7..8ed644f 100644
--- a/Documentation/powerpc/booting-without-of.txt
+++ b/Documentation/powerpc/booting-without-of.txt
@@ -2816,6 +2816,39 @@ platforms are moved over to use the flattened-device-tree model.
big-endian;
};

+ r) Freescale Display Interface Unit
+
+ The Freescale DIU is a LCD controller, with proper hardware, it can also
+ drive DVI monitors.
+
+ Required properties:
+ - compatible : should be "fsl-diu".
+ - reg : should contain at least address and length of the DIU register
+ set.
+ - Interrupts : one DIU interrupt should be describe here.
+
+ Example (MPC8610HPCD)
+ display@2c000 {
+ compatible = "fsl,diu";
+ reg = <0x2c000 100>;
+ interrupts = <72 2>;
+ interrupt-parent = <&mpic>;
+ };
+
+ s) Freescale on board FPGA
+
+ This is the memory-mapped registers for on board FPGA.
+
+ Required properities:
+ - compatible : should be "fsl,fpga-pixis".
+ - reg : should contain the address and the lenght of the FPPGA register
+ set.
+
+ Example (MPC8610HPCD)
+ board-control@e8000000 {
+ compatible = "fsl,fpga-pixis";
+ reg = <0xe8000000 20>;
+ };

More devices will be defined as this spec matures.

diff --git a/arch/powerpc/boot/dts/mpc8610_hpcd.dts b/arch/powerpc/boot/dts/mpc8610_hpcd.dts
index 16c947b..7f3d64f 100644
--- a/arch/powerpc/boot/dts/mpc8610_hpcd.dts
+++ b/arch/powerpc/boot/dts/mpc8610_hpcd.dts
@@ -45,6 +45,11 @@
reg = <0x00000000 0x20000000>; // 512M at 0x0
};

+ board-control@e8000000 {
+ compatible = "fsl,fpga-pixis";
+ reg = <0xe8000000 20>; // pixis at 0xe8000000
+ };
+
soc@e0000000 {
#address-cells = <1>;
#size-cells = <1>;
@@ -104,6 +109,13 @@
interrupt-parent = <&mpic>;
};

+ display@2c000 {
+ compatible = "fsl,diu";
+ reg = <0x2c000 100>;
+ interrupts = <72 2>;
+ interrupt-parent = <&mpic>;
+ };
+
mpic: interrupt-controller@40000 {
clock-frequency = <0>;
interrupt-controller;
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index e0b0580..d9c6be4 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -1779,6 +1779,16 @@ config FB_MBX_DEBUG

If unsure, say N.

+config FB_FSL_DIU
+ tristate "Freescale DIU framebuffer support"
+ depends on FB && FSL_SOC
+ select FB_CFB_FILLRECT
+ select FB_CFB_COPYAREA
+ select FB_CFB_IMAGEBLIT
+ select PPC_LIB_RHEAP
+ ---help---
+ Framebuffer driver for the Freescale SoC DIU
+
config FB_W100
tristate "W100 frame buffer support"
depends on FB && PXA_SHARPSL
diff --git a/drivers/video/Makefile b/drivers/video/Makefile
index 03371c7..3b9a3ce 100644
--- a/drivers/video/Makefile
+++ b/drivers/video/Makefile
@@ -113,6 +113,7 @@ obj-$(CONFIG_FB_PS3) += ps3fb.o
obj-$(CONFIG_FB_SM501) += sm501fb.o
obj-$(CONFIG_FB_XILINX) += xilinxfb.o
obj-$(CONFIG_FB_OMAP) += omap/
+obj-$(CONFIG_FB_FSL_DIU) += fsl-diu-fb.o

# Platform or fallback drivers go here
obj-$(CONFIG_FB_UVESA) += uvesafb.o
diff --git a/drivers/video/fsl-diu-fb.c b/drivers/video/fsl-diu-fb.c
new file mode 100644
index 0000000..a84129c
--- /dev/null
+++ b/drivers/video/fsl-diu-fb.c
@@ -0,0 +1,1741 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * Freescale DIU Frame Buffer device driver
+ *
+ * Authors: Hongjun Chen <hong-jun.chen@freescale.com>
+ * Paul Widmer <paul.widmer@freescale.com>
+ * Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
+ * York Sun <yorksun@freescale.com>
+ *
+ * Based on imxfb.c Copyright (C) 2004 S.Hauer, Pengutronix
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/string.h>
+#include <linux/slab.h>
+#include <linux/fb.h>
+#include <linux/init.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/clk.h>
+#include <linux/uaccess.h>
+#include <linux/vmalloc.h>
+
+#include <linux/of_platform.h>
+
+#include <sysdev/fsl_soc.h>
+#include "fsl-diu-fb.h"
+
+/*
+ * These parameters give default parameters
+ * for video output 1024x768,
+ * FIXME - change timing to proper amounts
+ * hsync 31.5kHz, vsync 60Hz
+ */
+static struct fb_videomode __devinitdata fsl_diu_default_mode = {
+ .refresh = 60,
+ .xres = 1024,
+ .yres = 768,
+ .pixclock = 15385,
+ .left_margin = 160,
+ .right_margin = 24,
+ .upper_margin = 29,
+ .lower_margin = 3,
+ .hsync_len = 136,
+ .vsync_len = 6,
+ .sync = FB_SYNC_COMP_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+ .vmode = FB_VMODE_NONINTERLACED
+};
+
+static struct fb_videomode __devinitdata fsl_diu_mode_db[] = {
+ {
+ .name = "1024x768-60",
+ .refresh = 60,
+ .xres = 1024,
+ .yres = 768,
+ .pixclock = 15385,
+ .left_margin = 160,
+ .right_margin = 24,
+ .upper_margin = 29,
+ .lower_margin = 3,
+ .hsync_len = 136,
+ .vsync_len = 6,
+ .sync = FB_SYNC_COMP_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+ .vmode = FB_VMODE_NONINTERLACED
+ },
+ {
+ .name = "1024x768-70",
+ .refresh = 70,
+ .xres = 1024,
+ .yres = 768,
+ .pixclock = 16886,
+ .left_margin = 3,
+ .right_margin = 3,
+ .upper_margin = 2,
+ .lower_margin = 2,
+ .hsync_len = 40,
+ .vsync_len = 18,
+ .sync = FB_SYNC_COMP_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+ .vmode = FB_VMODE_NONINTERLACED
+ },
+ {
+ .name = "1024x768-75",
+ .refresh = 75,
+ .xres = 1024,
+ .yres = 768,
+ .pixclock = 15009,
+ .left_margin = 3,
+ .right_margin = 3,
+ .upper_margin = 2,
+ .lower_margin = 2,
+ .hsync_len = 80,
+ .vsync_len = 32,
+ .sync = FB_SYNC_COMP_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+ .vmode = FB_VMODE_NONINTERLACED
+ },
+ {
+ .name = "1280x1024-60",
+ .refresh = 60,
+ .xres = 1280,
+ .yres = 1024,
+ .pixclock = 9375,
+ .left_margin = 38,
+ .right_margin = 128,
+ .upper_margin = 2,
+ .lower_margin = 7,
+ .hsync_len = 216,
+ .vsync_len = 37,
+ .sync = FB_SYNC_COMP_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+ .vmode = FB_VMODE_NONINTERLACED
+ },
+ {
+ .name = "1280x1024-70",
+ .refresh = 70,
+ .xres = 1280,
+ .yres = 1024,
+ .pixclock = 9380,
+ .left_margin = 6,
+ .right_margin = 6,
+ .upper_margin = 4,
+ .lower_margin = 4,
+ .hsync_len = 60,
+ .vsync_len = 94,
+ .sync = FB_SYNC_COMP_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+ .vmode = FB_VMODE_NONINTERLACED
+ },
+ {
+ .name = "1280x1024-75",
+ .refresh = 75,
+ .xres = 1280,
+ .yres = 1024,
+ .pixclock = 9380,
+ .left_margin = 6,
+ .right_margin = 6,
+ .upper_margin = 4,
+ .lower_margin = 4,
+ .hsync_len = 60,
+ .vsync_len = 15,
+ .sync = FB_SYNC_COMP_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+ .vmode = FB_VMODE_NONINTERLACED
+ },
+ {
+ .name = "320x240", /* for AOI only */
+ .refresh = 60,
+ .xres = 320,
+ .yres = 240,
+ .pixclock = 15385,
+ .left_margin = 0,
+ .right_margin = 0,
+ .upper_margin = 0,
+ .lower_margin = 0,
+ .hsync_len = 0,
+ .vsync_len = 0,
+ .sync = FB_SYNC_COMP_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+ .vmode = FB_VMODE_NONINTERLACED
+ },
+ {
+ .name = "1280x480-60",
+ .refresh = 60,
+ .xres = 1280,
+ .yres = 480,
+ .pixclock = 18939,
+ .left_margin = 353,
+ .right_margin = 47,
+ .upper_margin = 39,
+ .lower_margin = 4,
+ .hsync_len = 8,
+ .vsync_len = 2,
+ .sync = FB_SYNC_COMP_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+ .vmode = FB_VMODE_NONINTERLACED
+ },
+};
+
+static char *fb_mode = "1024x768-32@60";
+static unsigned long default_bpp = 32;
+static int monitor_port;
+
+#if defined(CONFIG_NOT_COHERENT_CACHE)
+static u8 *coherence_data;
+static size_t coherence_data_size;
+static unsigned int d_cache_line_size;
+#endif
+
+static DEFINE_SPINLOCK(diu_lock);
+
+struct fsl_diu_data {
+ struct fb_info *fsl_diu_info[FSL_AOI_NUM - 1];
+ /*FSL_AOI_NUM has one dummy AOI */
+ struct device_attribute dev_attr;
+ struct diu_ad *dummy_ad;
+ void *dummy_aoi_virt;
+ unsigned int irq;
+ int fb_enabled;
+ int monitor_port;
+};
+
+struct mfb_info {
+ int index;
+ int type;
+ char *id;
+ int registered;
+ int blank;
+ unsigned long pseudo_palette[16];
+ struct diu_ad *ad;
+ int cursor_reset;
+ unsigned char g_alpha;
+ unsigned int count;
+ int x_aoi_d; /* aoi display x offset to physical screen */
+ int y_aoi_d; /* aoi display y offset to physical screen */
+ struct fsl_diu_data *parent;
+};
+
+
+static struct mfb_info mfb_template[] = {
+ { /* AOI 0 for plane 0 */
+ .index = 0,
+ .type = MFB_TYPE_OUTPUT,
+ .id = "Panel0",
+ .registered = 0,
+ .count = 0,
+ .x_aoi_d = 0,
+ .y_aoi_d = 0,
+ },
+ { /* AOI 0 for plane 1 */
+ .index = 1,
+ .type = MFB_TYPE_OUTPUT,
+ .id = "Panel1 AOI0",
+ .registered = 0,
+ .g_alpha = 0xff,
+ .count = 0,
+ .x_aoi_d = 0,
+ .y_aoi_d = 0,
+ },
+ { /* AOI 1 for plane 1 */
+ .index = 2,
+ .type = MFB_TYPE_OUTPUT,
+ .id = "Panel1 AOI1",
+ .registered = 0,
+ .g_alpha = 0xff,
+ .count = 0,
+ .x_aoi_d = 0,
+ .y_aoi_d = 480,
+ },
+ { /* AOI 0 for plane 2 */
+ .index = 3,
+ .type = MFB_TYPE_OUTPUT,
+ .id = "Panel2 AOI0",
+ .registered = 0,
+ .g_alpha = 0xff,
+ .count = 0,
+ .x_aoi_d = 640,
+ .y_aoi_d = 0,
+ },
+ { /* AOI 1 for plane 2 */
+ .index = 4,
+ .type = MFB_TYPE_OUTPUT,
+ .id = "Panel2 AOI1",
+ .registered = 0,
+ .g_alpha = 0xff,
+ .count = 0,
+ .x_aoi_d = 640,
+ .y_aoi_d = 480,
+ },
+};
+
+static struct diu_hw dr = {
+ .mode = MFB_MODE1,
+ .reg_lock = __SPIN_LOCK_UNLOCKED(diu_hw.reg_lock),
+};
+
+static struct diu_pool pool;
+
+/* To allocate memory for framebuffer. First try __get_free_pages(). If it
+ * fails, try rh_alloc. The reason is __get_free_pages() cannot allocate
+ * very large memory (more than 4MB). We don't want to allocate all memory
+ * in rheap since small memory allocation/deallocation will fragment the
+ * rheap and make the furture large allocation fail.
+ */
+
+void *fsl_diu_alloc(unsigned long size, phys_addr_t *phys)
+{
+ void *virt;
+
+ pr_debug("size=%lu\n", size);
+
+ virt = (void *)__get_free_pages(GFP_DMA | __GFP_ZERO, get_order(size));
+ if (virt) {
+ *phys = virt_to_phys(virt);
+ pr_debug("virt %p, phys=%llx\n", virt, (uint64_t) *phys);
+ return virt;
+ }
+ if (!diu_ops.diu_mem) {
+ printk(KERN_INFO "%s: no diu_mem."
+ " To reserve more memory, put 'diufb=15M' "
+ "in the command line\n", __func__);
+ return NULL;
+ }
+
+ virt = (void *)rh_alloc(&diu_ops.diu_rh_info, size, "DIU");
+ if (virt) {
+ *phys = virt_to_bus(virt);
+ memset(virt, 0, size);
+ }
+
+ pr_debug("rh virt=%p phys=%lx\n", virt, *phys);
+
+ return virt;
+}
+
+void fsl_diu_free(void *p, unsigned long size)
+{
+ pr_debug("p=%p size=%lu\n", p, size);
+
+ if (!p)
+ return;
+
+ if ((p >= diu_ops.diu_mem) &&
+ (p < (diu_ops.diu_mem + diu_ops.diu_size))) {
+ pr_debug("rh\n");
+ rh_free(&diu_ops.diu_rh_info, (unsigned long) p);
+ } else {
+ pr_debug("dma\n");
+ free_pages((unsigned long)p, get_order(size));
+ }
+}
+
+static int fsl_diu_enable_panel(struct fb_info *info)
+{
+ struct mfb_info *pmfbi, *cmfbi, *mfbi = info->par;
+ struct diu *hw = dr.diu_reg;
+ struct diu_ad *ad = mfbi->ad;
+ struct fsl_diu_data *machine_data = mfbi->parent;
+ int res = 0;
+
+ pr_debug("enable_panel index %d\n", mfbi->index);
+ if (mfbi->type != MFB_TYPE_OFF) {
+ switch (mfbi->index) {
+ case 0: /* plane 0 */
+ if (hw->desc[0] != ad->paddr)
+ out_be32(&(hw->desc[0]), ad->paddr);
+ break;
+ case 1: /* plane 1 AOI 0 */
+ cmfbi = machine_data->fsl_diu_info[2]->par;
+ if (hw->desc[1] != ad->paddr) { /* AOI0 closed */
+ if (cmfbi->count > 0) /* AOI1 open */
+ ad->next_ad =
+ cpu_to_le32(cmfbi->ad->paddr);
+ else
+ ad->next_ad = 0;
+ out_be32(&(hw->desc[1]), ad->paddr);
+ }
+ break;
+ case 3: /* plane 2 AOI 0 */
+ cmfbi = machine_data->fsl_diu_info[4]->par;
+ if (hw->desc[2] != ad->paddr) { /* AOI0 closed */
+ if (cmfbi->count > 0) /* AOI1 open */
+ ad->next_ad =
+ cpu_to_le32(cmfbi->ad->paddr);
+ else
+ ad->next_ad = 0;
+ out_be32(&(hw->desc[2]), ad->paddr);
+ }
+ break;
+ case 2: /* plane 1 AOI 1 */
+ pmfbi = machine_data->fsl_diu_info[1]->par;
+ ad->next_ad = 0;
+ if (hw->desc[1] == machine_data->dummy_ad->paddr)
+ out_be32(&(hw->desc[1]), ad->paddr);
+ else /* AOI0 open */
+ pmfbi->ad->next_ad = cpu_to_le32(ad->paddr);
+ break;
+ case 4: /* plane 2 AOI 1 */
+ pmfbi = machine_data->fsl_diu_info[3]->par;
+ ad->next_ad = 0;
+ if (hw->desc[2] == machine_data->dummy_ad->paddr)
+ out_be32(&(hw->desc[2]), ad->paddr);
+ else /* AOI0 was open */
+ pmfbi->ad->next_ad = cpu_to_le32(ad->paddr);
+ break;
+ default:
+ res = -EINVAL;
+ break;
+ }
+ } else
+ res = -EINVAL;
+ return res;
+}
+
+static int fsl_diu_disable_panel(struct fb_info *info)
+{
+ struct mfb_info *pmfbi, *cmfbi, *mfbi = info->par;
+ struct diu *hw = dr.diu_reg;
+ struct diu_ad *ad = mfbi->ad;
+ struct fsl_diu_data *machine_data = mfbi->parent;
+ int res = 0;
+
+ switch (mfbi->index) {
+ case 0: /* plane 0 */
+ if (hw->desc[0] != machine_data->dummy_ad->paddr)
+ out_be32(&(hw->desc[0]),
+ machine_data->dummy_ad->paddr);
+ break;
+ case 1: /* plane 1 AOI 0 */
+ cmfbi = machine_data->fsl_diu_info[2]->par;
+ if (cmfbi->count > 0) /* AOI1 is open */
+ out_be32(&(hw->desc[1]), cmfbi->ad->paddr);
+ /* move AOI1 to the first */
+ else /* AOI1 was closed */
+ out_be32(&(hw->desc[1]),
+ machine_data->dummy_ad->paddr);
+ /* close AOI 0 */
+ break;
+ case 3: /* plane 2 AOI 0 */
+ cmfbi = machine_data->fsl_diu_info[4]->par;
+ if (cmfbi->count > 0) /* AOI1 is open */
+ out_be32(&(hw->desc[2]), cmfbi->ad->paddr);
+ /* move AOI1 to the first */
+ else /* AOI1 was closed */
+ out_be32(&(hw->desc[2]),
+ machine_data->dummy_ad->paddr);
+ /* close AOI 0 */
+ break;
+ case 2: /* plane 1 AOI 1 */
+ pmfbi = machine_data->fsl_diu_info[1]->par;
+ if (hw->desc[1] != ad->paddr) {
+ /* AOI1 is not the first in the chain */
+ if (pmfbi->count > 0)
+ /* AOI0 is open, must be the first */
+ pmfbi->ad->next_ad = 0;
+ } else /* AOI1 is the first in the chain */
+ out_be32(&(hw->desc[1]), machine_data->dummy_ad->paddr);
+ /* close AOI 1 */
+ break;
+ case 4: /* plane 2 AOI 1 */
+ pmfbi = machine_data->fsl_diu_info[3]->par;
+ if (hw->desc[2] != ad->paddr) {
+ /* AOI1 is not the first in the chain */
+ if (pmfbi->count > 0)
+ /* AOI0 is open, must be the first */
+ pmfbi->ad->next_ad = 0;
+ } else /* AOI1 is the first in the chain */
+ out_be32(&(hw->desc[2]), machine_data->dummy_ad->paddr);
+ /* close AOI 1 */
+ break;
+ default:
+ res = -EINVAL;
+ break;
+ }
+
+ return res;
+}
+
+static void enable_lcdc(struct fb_info *info)
+{
+ struct diu *hw = dr.diu_reg;
+ struct mfb_info *mfbi = info->par;
+ struct fsl_diu_data *machine_data = mfbi->parent;
+
+ if (!machine_data->fb_enabled) {
+ out_be32(&(hw->diu_mode), dr.mode);
+ machine_data->fb_enabled++;
+ }
+}
+
+static void disable_lcdc(struct fb_info *info)
+{
+ struct diu *hw = dr.diu_reg;
+ struct mfb_info *mfbi = info->par;
+ struct fsl_diu_data *machine_data = mfbi->parent;
+
+ if (machine_data->fb_enabled) {
+ out_be32(&(hw->diu_mode), 0);
+ machine_data->fb_enabled = 0;
+ }
+}
+
+static void adjust_aoi_size_position(struct fb_var_screeninfo *var,
+ struct fb_info *info)
+{
+ struct mfb_info *lower_aoi_mfbi, *upper_aoi_mfbi, *mfbi = info->par;
+ struct fsl_diu_data *machine_data = mfbi->parent;
+ int available_height, upper_aoi_bottom, index = mfbi->index;
+ int lower_aoi_is_open, upper_aoi_is_open;
+ __u32 base_plane_width, base_plane_height, upper_aoi_height;
+
+ base_plane_width = machine_data->fsl_diu_info[0]->var.xres;
+ base_plane_height = machine_data->fsl_diu_info[0]->var.yres;
+
+ switch (index) {
+ case 0:
+ if (mfbi->x_aoi_d != 0)
+ mfbi->x_aoi_d = 0;
+ if (mfbi->y_aoi_d != 0)
+ mfbi->y_aoi_d = 0;
+ break;
+ case 1: /* AOI 0 */
+ case 3:
+ lower_aoi_mfbi = machine_data->fsl_diu_info[index+1]->par;
+ lower_aoi_is_open = lower_aoi_mfbi->count > 0 ? 1 : 0;
+ if (var->xres > base_plane_width)
+ var->xres = base_plane_width;
+ if ((mfbi->x_aoi_d + var->xres) > base_plane_width)
+ mfbi->x_aoi_d = base_plane_width - var->xres;
+
+ if (lower_aoi_is_open)
+ available_height = lower_aoi_mfbi->y_aoi_d;
+ else
+ available_height = base_plane_height;
+ if (var->yres > available_height)
+ var->yres = available_height;
+ if ((mfbi->y_aoi_d + var->yres) > available_height)
+ mfbi->y_aoi_d = available_height - var->yres;
+ break;
+ case 2: /* AOI 1 */
+ case 4:
+ upper_aoi_mfbi = machine_data->fsl_diu_info[index-1]->par;
+ upper_aoi_height =
+ machine_data->fsl_diu_info[index-1]->var.yres;
+ upper_aoi_bottom = upper_aoi_mfbi->y_aoi_d + upper_aoi_height;
+ upper_aoi_is_open = upper_aoi_mfbi->count > 0 ? 1 : 0;
+ if (var->xres > base_plane_width)
+ var->xres = base_plane_width;
+ if ((mfbi->x_aoi_d + var->xres) > base_plane_width)
+ mfbi->x_aoi_d = base_plane_width - var->xres;
+ if (mfbi->y_aoi_d < 0)
+ mfbi->y_aoi_d = 0;
+ if (upper_aoi_is_open) {
+ if (mfbi->y_aoi_d < upper_aoi_bottom)
+ mfbi->y_aoi_d = upper_aoi_bottom;
+ available_height = base_plane_height
+ - upper_aoi_bottom;
+ } else
+ available_height = base_plane_height;
+ if (var->yres > available_height)
+ var->yres = available_height;
+ if ((mfbi->y_aoi_d + var->yres) > base_plane_height)
+ mfbi->y_aoi_d = base_plane_height - var->yres;
+ break;
+ }
+}
+/*
+ * Checks to see if the hardware supports the state requested by var passed
+ * in. This function does not alter the hardware state! If the var passed in
+ * is slightly off by what the hardware can support then we alter the var
+ * PASSED in to what we can do. If the hardware doesn't support mode change
+ * a -EINVAL will be returned by the upper layers.
+ */
+static int fsl_diu_check_var(struct fb_var_screeninfo *var,
+ struct fb_info *info)
+{
+ unsigned long htotal, vtotal;
+
+ pr_debug("check_var xres: %d\n", var->xres);
+ pr_debug("check_var yres: %d\n", var->yres);
+
+ if (var->xres_virtual < var->xres)
+ var->xres_virtual = var->xres;
+ if (var->yres_virtual < var->yres)
+ var->yres_virtual = var->yres;
+
+ if (var->xoffset < 0)
+ var->xoffset = 0;
+
+ if (var->yoffset < 0)
+ var->yoffset = 0;
+
+ if (var->xoffset + info->var.xres > info->var.xres_virtual)
+ var->xoffset = info->var.xres_virtual - info->var.xres;
+
+ if (var->yoffset + info->var.yres > info->var.yres_virtual)
+ var->yoffset = info->var.yres_virtual - info->var.yres;
+
+ if ((var->bits_per_pixel != 32) && (var->bits_per_pixel != 24) &&
+ (var->bits_per_pixel != 16))
+ var->bits_per_pixel = default_bpp;
+
+ switch (var->bits_per_pixel) {
+ case 16:
+ var->red.length = 5;
+ var->red.offset = 11;
+ var->red.msb_right = 0;
+
+ var->green.length = 6;
+ var->green.offset = 5;
+ var->green.msb_right = 0;
+
+ var->blue.length = 5;
+ var->blue.offset = 0;
+ var->blue.msb_right = 0;
+
+ var->transp.length = 0;
+ var->transp.offset = 0;
+ var->transp.msb_right = 0;
+ break;
+ case 24:
+ var->red.length = 8;
+ var->red.offset = 0;
+ var->red.msb_right = 0;
+
+ var->green.length = 8;
+ var->green.offset = 8;
+ var->green.msb_right = 0;
+
+ var->blue.length = 8;
+ var->blue.offset = 16;
+ var->blue.msb_right = 0;
+
+ var->transp.length = 0;
+ var->transp.offset = 0;
+ var->transp.msb_right = 0;
+ break;
+ case 32:
+ var->red.length = 8;
+ var->red.offset = 16;
+ var->red.msb_right = 0;
+
+ var->green.length = 8;
+ var->green.offset = 8;
+ var->green.msb_right = 0;
+
+ var->blue.length = 8;
+ var->blue.offset = 0;
+ var->blue.msb_right = 0;
+
+ var->transp.length = 8;
+ var->transp.offset = 24;
+ var->transp.msb_right = 0;
+
+ break;
+ }
+ /* If the pixclock is below the minimum spec'd value then set to
+ * refresh rate for 60Hz since this is supported by most monitors.
+ * Refer to Documentation/fb/ for calculations.
+ */
+ if ((var->pixclock < MIN_PIX_CLK) || (var->pixclock > MAX_PIX_CLK)) {
+ htotal = var->xres + var->right_margin + var->hsync_len +
+ var->left_margin;
+ vtotal = var->yres + var->lower_margin + var->vsync_len +
+ var->upper_margin;
+ var->pixclock = (vtotal * htotal * 6UL) / 100UL;
+ var->pixclock = KHZ2PICOS(var->pixclock);
+ pr_debug("pixclock set for 60Hz refresh = %u ps\n",
+ var->pixclock);
+ }
+
+ var->height = -1;
+ var->width = -1;
+ var->grayscale = 0;
+
+ /* Copy nonstd field to/from sync for fbset usage */
+ var->sync |= var->nonstd;
+ var->nonstd |= var->sync;
+
+ adjust_aoi_size_position(var, info);
+ return 0;
+}
+
+static void set_fix(struct fb_info *info)
+{
+ struct fb_fix_screeninfo *fix = &info->fix;
+ struct fb_var_screeninfo *var = &info->var;
+ struct mfb_info *mfbi = info->par;
+
+ strncpy(fix->id, mfbi->id, strlen(mfbi->id));
+ fix->line_length = var->xres_virtual * var->bits_per_pixel / 8;
+ fix->type = FB_TYPE_PACKED_PIXELS;
+ fix->accel = FB_ACCEL_NONE;
+ fix->visual = FB_VISUAL_TRUECOLOR;
+ fix->xpanstep = 1;
+ fix->ypanstep = 1;
+}
+
+static void update_lcdc(struct fb_info *info)
+{
+ struct fb_var_screeninfo *var = &info->var;
+ struct mfb_info *mfbi = info->par;
+ struct fsl_diu_data *machine_data = mfbi->parent;
+ struct diu *hw;
+ int i, j;
+ char __iomem *cursor_base, *gamma_table_base;
+
+ u32 temp;
+
+ hw = dr.diu_reg;
+
+ if (mfbi->type == MFB_TYPE_OFF) {
+ fsl_diu_disable_panel(info);
+ return;
+ }
+
+ diu_ops.set_monitor_port(machine_data->monitor_port);
+ gamma_table_base = pool.gamma.vaddr;
+ cursor_base = pool.cursor.vaddr;
+ /* Prep for DIU init - gamma table, cursor table */
+
+ for (i = 0; i <= 2; i++)
+ for (j = 0; j <= 255; j++)
+ *gamma_table_base++ = j;
+
+ diu_ops.set_gamma_table(machine_data->monitor_port, pool.gamma.vaddr);
+
+ pr_debug("update-lcdc: HW - %p\n Disabling DIU\n", hw);
+ disable_lcdc(info);
+
+ /* Program DIU registers */
+
+ out_be32(&(hw->gamma), pool.gamma.paddr);
+ out_be32(&(hw->cursor), pool.cursor.paddr);
+
+ out_be32(&(hw->bgnd), 0x007F7F7F); /* BGND */
+ out_be32(&(hw->bgnd_wb), 0); /* BGND_WB */
+ out_be32(&(hw->disp_size), (var->yres << 16 | var->xres));
+ /* DISP SIZE */
+ pr_debug("DIU xres: %d\n", var->xres);
+ pr_debug("DIU yres: %d\n", var->yres);
+
+ out_be32(&(hw->wb_size), 0); /* WB SIZE */
+ out_be32(&(hw->wb_mem_addr), 0); /* WB MEM ADDR */
+
+ /* Horizontal and vertical configuration register */
+ temp = var->left_margin << 22 | /* BP_H */
+ var->hsync_len << 11 | /* PW_H */
+ var->right_margin; /* FP_H */
+
+ out_be32(&(hw->hsyn_para), temp);
+
+ temp = var->upper_margin << 22 | /* BP_V */
+ var->vsync_len << 11 | /* PW_V */
+ var->lower_margin; /* FP_V */
+
+ out_be32(&(hw->vsyn_para), temp);
+
+ pr_debug("DIU right_margin - %d\n", var->right_margin);
+ pr_debug("DIU left_margin - %d\n", var->left_margin);
+ pr_debug("DIU hsync_len - %d\n", var->hsync_len);
+ pr_debug("DIU upper_margin - %d\n", var->upper_margin);
+ pr_debug("DIU lower_margin - %d\n", var->lower_margin);
+ pr_debug("DIU vsync_len - %d\n", var->vsync_len);
+ pr_debug("DIU HSYNC - 0x%08x\n", hw->hsyn_para);
+ pr_debug("DIU VSYNC - 0x%08x\n", hw->vsyn_para);
+
+ diu_ops.set_pixel_clock(var->pixclock);
+
+ out_be32(&(hw->syn_pol), 0); /* SYNC SIGNALS POLARITY */
+ out_be32(&(hw->thresholds), 0x00037800); /* The Thresholds */
+ out_be32(&(hw->int_status), 0); /* INTERRUPT STATUS */
+ out_be32(&(hw->plut), 0x01F5F666);
+
+ /* Enable the DIU */
+ enable_lcdc(info);
+}
+
+static int map_video_memory(struct fb_info *info)
+{
+ phys_addr_t phys;
+
+ pr_debug("info->var.xres_virtual = %d\n", info->var.xres_virtual);
+ pr_debug("info->var.yres_virtual = %d\n", info->var.yres_virtual);
+ pr_debug("info->fix.line_length = %d\n", info->fix.line_length);
+
+ info->fix.smem_len = info->fix.line_length * info->var.yres_virtual;
+ pr_debug("MAP_VIDEO_MEMORY: smem_len = %d\n", info->fix.smem_len);
+ info->screen_base = fsl_diu_alloc(info->fix.smem_len, &phys);
+ if (info->screen_base == 0) {
+ printk(KERN_ERR "Unable to allocate fb memory\n");
+ return -ENOMEM;
+ }
+ info->fix.smem_start = (unsigned long) phys;
+ info->screen_size = info->fix.smem_len;
+
+ pr_debug("Allocated fb @ paddr=0x%08lx, size=%d.\n",
+ info->fix.smem_start,
+ info->fix.smem_len);
+ pr_debug("screen base %p\n", info->screen_base);
+
+ return 0;
+}
+
+static void unmap_video_memory(struct fb_info *info)
+{
+ fsl_diu_free(info->screen_base, info->fix.smem_len);
+ info->screen_base = 0;
+ info->fix.smem_start = 0;
+ info->fix.smem_len = 0;
+}
+
+/*
+ * Using the fb_var_screeninfo in fb_info we set the resolution of this
+ * particular framebuffer. This function alters the fb_fix_screeninfo stored
+ * in fb_info. It does not alter var in fb_info since we are using that
+ * data. This means we depend on the data in var inside fb_info to be
+ * supported by the hardware. fsl_diu_check_var is always called before
+ * fsl_diu_set_par to ensure this.
+ */
+static int fsl_diu_set_par(struct fb_info *info)
+{
+ unsigned long len;
+ struct fb_var_screeninfo *var = &info->var;
+ struct mfb_info *mfbi = info->par;
+ struct fsl_diu_data *machine_data = mfbi->parent;
+ struct diu_ad *ad = mfbi->ad;
+ struct diu *hw;
+
+ hw = dr.diu_reg;
+
+ set_fix(info);
+ mfbi->cursor_reset = 1;
+
+ len = info->var.yres_virtual * info->fix.line_length;
+ /* Alloc & dealloc each time resolution/bpp change */
+ if (len != info->fix.smem_len) {
+ if (info->fix.smem_start)
+ unmap_video_memory(info);
+ pr_debug("SET PAR: smem_len = %d\n", info->fix.smem_len);
+
+ /* Memory allocation for framebuffer */
+ if (map_video_memory(info)) {
+ printk(KERN_ERR "Unable to allocate fb memory 1\n");
+ return -ENOMEM;
+ }
+ }
+
+ ad->pix_fmt =
+ diu_ops.get_pixel_format(var->bits_per_pixel,
+ machine_data->monitor_port);
+ ad->addr = cpu_to_le32(info->fix.smem_start);
+ ad->src_size_g_alpha = cpu_to_le32((var->yres << 12) |
+ var->xres) | mfbi->g_alpha;
+ /* fix me. AOI should not be greater than display size */
+ ad->aoi_size = cpu_to_le32((var->yres << 16) | var->xres);
+ ad->offset_xyi = 0;
+ ad->offset_xyd = cpu_to_le32((mfbi->y_aoi_d << 16) | mfbi->x_aoi_d);
+
+ /* Disable chroma keying function */
+ ad->ckmax_r = 0;
+ ad->ckmax_g = 0;
+ ad->ckmax_b = 0;
+
+ ad->ckmin_r = 255;
+ ad->ckmin_g = 255;
+ ad->ckmin_b = 255;
+
+ if (mfbi->index == 0)
+ update_lcdc(info);
+ return 0;
+}
+
+static inline __u32 CNVT_TOHW(__u32 val, __u32 width)
+{
+ return ((val<<width) + 0x7FFF - val)>>16;
+}
+
+/*
+ * Set a single color register. The values supplied have a 16 bit magnitude
+ * which needs to be scaled in this function for the hardware. Things to take
+ * into consideration are how many color registers, if any, are supported with
+ * the current color visual. With truecolor mode no color palettes are
+ * supported. Here a psuedo palette is created which we store the value in
+ * pseudo_palette in struct fb_info. For pseudocolor mode we have a limited
+ * color palette.
+ */
+static int fsl_diu_setcolreg(unsigned regno, unsigned red, unsigned green,
+ unsigned blue, unsigned transp, struct fb_info *info)
+{
+ int ret = 1;
+
+ /*
+ * If greyscale is true, then we convert the RGB value
+ * to greyscale no matter what visual we are using.
+ */
+ if (info->var.grayscale)
+ red = green = blue = (19595 * red + 38470 * green +
+ 7471 * blue) >> 16;
+ switch (info->fix.visual) {
+ case FB_VISUAL_TRUECOLOR:
+ /*
+ * 16-bit True Colour. We encode the RGB value
+ * according to the RGB bitfield information.
+ */
+ if (regno < 16) {
+ u32 *pal = info->pseudo_palette;
+ u32 v;
+
+ red = CNVT_TOHW(red, info->var.red.length);
+ green = CNVT_TOHW(green, info->var.green.length);
+ blue = CNVT_TOHW(blue, info->var.blue.length);
+ transp = CNVT_TOHW(transp, info->var.transp.length);
+
+ v = (red << info->var.red.offset) |
+ (green << info->var.green.offset) |
+ (blue << info->var.blue.offset) |
+ (transp << info->var.transp.offset);
+
+ pal[regno] = v;
+ ret = 0;
+ }
+ break;
+ case FB_VISUAL_STATIC_PSEUDOCOLOR:
+ case FB_VISUAL_PSEUDOCOLOR:
+ break;
+ }
+
+ return ret;
+}
+
+/*
+ * Pan (or wrap, depending on the `vmode' field) the display using the
+ * 'xoffset' and 'yoffset' fields of the 'var' structure. If the values
+ * don't fit, return -EINVAL.
+ */
+static int fsl_diu_pan_display(struct fb_var_screeninfo *var,
+ struct fb_info *info)
+{
+ if ((info->var.xoffset == var->xoffset) &&
+ (info->var.yoffset == var->yoffset))
+ return 0; /* No change, do nothing */
+
+ if (var->xoffset < 0 || var->yoffset < 0
+ || var->xoffset + info->var.xres > info->var.xres_virtual
+ || var->yoffset + info->var.yres > info->var.yres_virtual)
+ return -EINVAL;
+
+ info->var.xoffset = var->xoffset;
+ info->var.yoffset = var->yoffset;
+
+ if (var->vmode & FB_VMODE_YWRAP)
+ info->var.vmode |= FB_VMODE_YWRAP;
+ else
+ info->var.vmode &= ~FB_VMODE_YWRAP;
+
+ return 0;
+}
+
+/*
+ * Blank the screen if blank_mode != 0, else unblank. Return 0 if blanking
+ * succeeded, != 0 if un-/blanking failed.
+ * blank_mode == 2: suspend vsync
+ * blank_mode == 3: suspend hsync
+ * blank_mode == 4: powerdown
+ */
+static int fsl_diu_blank(int blank_mode, struct fb_info *info)
+{
+ struct mfb_info *mfbi = info->par;
+
+ mfbi->blank = blank_mode;
+
+ switch (blank_mode) {
+ case FB_BLANK_VSYNC_SUSPEND:
+ case FB_BLANK_HSYNC_SUSPEND:
+ /* FIXME: fixes to enable_panel and enable lcdc needed */
+ case FB_BLANK_NORMAL:
+ /* fsl_diu_disable_panel(info);*/
+ break;
+ case FB_BLANK_POWERDOWN:
+ /* disable_lcdc(info); */
+ break;
+ case FB_BLANK_UNBLANK:
+ /* fsl_diu_enable_panel(info);*/
+ break;
+ }
+
+ return 0;
+}
+
+static int fsl_diu_ioctl(struct fb_info *info, unsigned int cmd,
+ unsigned long arg)
+{
+ struct mfb_info *mfbi = info->par;
+ struct diu_ad *ad = mfbi->ad;
+ struct mfb_chroma_key ck;
+ unsigned char global_alpha;
+ struct aoi_display_offset aoi_d;
+ __u32 pix_fmt;
+
+ switch (cmd) {
+ case MFB_SET_PIXFMT:
+ if (!arg)
+ return -EINVAL;
+ if (copy_from_user(&pix_fmt, (void __user *)arg,
+ sizeof(pix_fmt)))
+ return -EFAULT;
+ ad->pix_fmt = pix_fmt;
+ pr_debug("Set pixel format to 0x%08x\n", ad->pix_fmt);
+ break;
+ case MFB_GET_PIXFMT:
+ if (!arg)
+ return -EINVAL;
+ pix_fmt = ad->pix_fmt;
+ if (copy_to_user((void *)arg, &pix_fmt, sizeof(pix_fmt)))
+ return -EFAULT;
+ pr_debug("get pixel format 0x%08x\n", ad->pix_fmt);
+ break;
+ case MFB_SET_AOID:
+ if (!arg)
+ return -EINVAL;
+ if (copy_from_user(&aoi_d, (void *)arg, sizeof(aoi_d)))
+ return -EFAULT;
+ mfbi->x_aoi_d = aoi_d.x_aoi_d;
+ mfbi->y_aoi_d = aoi_d.y_aoi_d;
+ pr_debug("set AOI display offset of index %d to (%d,%d)\n",
+ mfbi->index, aoi_d.x_aoi_d, aoi_d.y_aoi_d);
+ fsl_diu_check_var(&info->var, info);
+ fsl_diu_set_par(info);
+ break;
+ case MFB_GET_AOID:
+ if (!arg)
+ return -EINVAL;
+ aoi_d.x_aoi_d = mfbi->x_aoi_d;
+ aoi_d.y_aoi_d = mfbi->y_aoi_d;
+ if (copy_to_user((void *)arg, &aoi_d, sizeof(aoi_d)))
+ return -EFAULT;
+ pr_debug("get AOI display offset of index %d (%d,%d)\n",
+ mfbi->index, aoi_d.x_aoi_d, aoi_d.y_aoi_d);
+ break;
+ case MFB_GET_ALPHA:
+ if (!arg)
+ return -EINVAL;
+ global_alpha = mfbi->g_alpha;
+ if (copy_to_user((void *)arg, &global_alpha,
+ sizeof(global_alpha)))
+ return -EFAULT;
+ pr_debug("get global alpha of index %d\n", mfbi->index);
+ break;
+ case MFB_SET_ALPHA:
+ if (!arg)
+ return -EINVAL;
+
+ /* set panel information */
+ if (copy_from_user(&global_alpha, (void *)arg,
+ sizeof(global_alpha)))
+ return -EFAULT;
+ ad->src_size_g_alpha = (ad->src_size_g_alpha & (~0xff)) |
+ (global_alpha & 0xff);
+ mfbi->g_alpha = global_alpha;
+ pr_debug("set global alpha for index %d\n", mfbi->index);
+ break;
+ case MFB_SET_CHROMA_KEY:
+ if (!arg)
+ return -EINVAL;
+
+ /* set panel winformation */
+ if (copy_from_user(&ck, (void *)arg, sizeof(ck)))
+ return -EFAULT;
+
+ if (ck.enable &&
+ (ck.red_max < ck.red_min ||
+ ck.green_max < ck.green_min ||
+ ck.blue_max < ck.blue_min))
+ return -EINVAL;
+
+ if (!ck.enable) {
+ ad->ckmax_r = 0;
+ ad->ckmax_g = 0;
+ ad->ckmax_b = 0;
+ ad->ckmin_r = 255;
+ ad->ckmin_g = 255;
+ ad->ckmin_b = 255;
+ } else {
+ ad->ckmax_r = ck.red_max;
+ ad->ckmax_g = ck.green_max;
+ ad->ckmax_b = ck.blue_max;
+ ad->ckmin_r = ck.red_min;
+ ad->ckmin_g = ck.green_min;
+ ad->ckmin_b = ck.blue_min;
+ }
+ pr_debug("set chroma key\n");
+ break;
+ case FBIOGET_GWINFO:
+ if (mfbi->type == MFB_TYPE_OFF)
+ return -ENODEV;
+
+ if (!arg)
+ return -EINVAL;
+
+ /* get graphic window information */
+ if (copy_to_user((void *)arg, ad, sizeof(*ad)))
+ return -EFAULT;
+ break;
+ case FBIOGET_HWCINFO:
+ pr_debug("FBIOGET_HWCINFO:0x%08x\n", FBIOGET_HWCINFO);
+ break;
+ case FBIOPUT_MODEINFO:
+ pr_debug("FBIOPUT_MODEINFO:0x%08x\n", FBIOPUT_MODEINFO);
+ break;
+ case FBIOGET_DISPINFO:
+ pr_debug("FBIOGET_DISPINFO:0x%08x\n", FBIOGET_DISPINFO);
+ break;
+
+ default:
+ printk(KERN_ERR "Unknown ioctl command (0x%08X)\n", cmd);
+ return 0;
+ }
+
+ return 0;
+}
+
+/* turn on fb if count == 1
+ */
+static int fsl_diu_open(struct fb_info *info, int user)
+{
+ struct mfb_info *mfbi = info->par;
+ int res = 0;
+
+ spin_lock(&diu_lock);
+ mfbi->count++;
+ if (mfbi->count == 1) {
+ pr_debug("open plane index %d\n", mfbi->index);
+ fsl_diu_check_var(&info->var, info);
+ res = fsl_diu_set_par(info);
+ if (res < 0)
+ mfbi->count--;
+ else {
+ res = fsl_diu_enable_panel(info);
+ if (res < 0)
+ mfbi->count--;
+ }
+ }
+
+ spin_unlock(&diu_lock);
+ return res;
+}
+
+/* turn off fb if count == 0
+ */
+static int fsl_diu_release(struct fb_info *info, int user)
+{
+ struct mfb_info *mfbi = info->par;
+ int res = 0;
+
+ spin_lock(&diu_lock);
+ mfbi->count--;
+ if (mfbi->count == 0) {
+ pr_debug("release plane index %d\n", mfbi->index);
+ res = fsl_diu_disable_panel(info);
+ if (res < 0)
+ mfbi->count++;
+ }
+ spin_unlock(&diu_lock);
+ return res;
+}
+
+static struct fb_ops fsl_diu_ops = {
+ .owner = THIS_MODULE,
+ .fb_check_var = fsl_diu_check_var,
+ .fb_set_par = fsl_diu_set_par,
+ .fb_setcolreg = fsl_diu_setcolreg,
+ .fb_blank = fsl_diu_blank,
+ .fb_pan_display = fsl_diu_pan_display,
+ .fb_fillrect = cfb_fillrect,
+ .fb_copyarea = cfb_copyarea,
+ .fb_imageblit = cfb_imageblit,
+ .fb_ioctl = fsl_diu_ioctl,
+ .fb_open = fsl_diu_open,
+ .fb_release = fsl_diu_release,
+};
+
+static int init_fbinfo(struct fb_info *info)
+{
+ struct mfb_info *mfbi = info->par;
+
+ info->device = NULL;
+ info->var.activate = FB_ACTIVATE_NOW;
+ info->fbops = &fsl_diu_ops;
+ info->flags = FBINFO_FLAG_DEFAULT;
+ info->pseudo_palette = &mfbi->pseudo_palette;
+
+ /* Allocate colormap */
+ fb_alloc_cmap(&info->cmap, 16, 0);
+ return 0;
+}
+
+static int install_fb(struct fb_info *info)
+{
+ int rc;
+ struct mfb_info *mfbi = info->par;
+ const char *aoi_mode, *init_aoi_mode = "320x240";
+
+ if (init_fbinfo(info))
+ return -EINVAL;
+
+ if (mfbi->index == 0) /* plane 0 */
+ aoi_mode = fb_mode;
+ else
+ aoi_mode = init_aoi_mode;
+ pr_debug("mode used = %s\n", aoi_mode);
+ rc = fb_find_mode(&info->var, info, aoi_mode, fsl_diu_mode_db,
+ ARRAY_SIZE(fsl_diu_mode_db), &fsl_diu_default_mode, default_bpp);
+
+ switch (rc) {
+ case 1:
+ pr_debug("using mode specified in @mode\n");
+ break;
+ case 2:
+ pr_debug("using mode specified in @mode "
+ "with ignored refresh rate\n");
+ break;
+ case 3:
+ pr_debug("using mode default mode\n");
+ break;
+ case 4:
+ pr_debug("using mode from list\n");
+ break;
+ default:
+ pr_debug("rc = %d\n", rc);
+ pr_debug("failed to find mode\n");
+ return -EINVAL;
+ break;
+ }
+
+ pr_debug("xres_virtual %d\n", info->var.xres_virtual);
+ pr_debug("bits_per_pixel %d\n", info->var.bits_per_pixel);
+
+ pr_debug("info->var.yres_virtual = %d\n", info->var.yres_virtual);
+ pr_debug("info->fix.line_length = %d\n", info->fix.line_length);
+
+ if (mfbi->type == MFB_TYPE_OFF)
+ mfbi->blank = FB_BLANK_NORMAL;
+ else
+ mfbi->blank = FB_BLANK_UNBLANK;
+
+ if (fsl_diu_check_var(&info->var, info)) {
+ printk(KERN_ERR "fb_check_var failed");
+ fb_dealloc_cmap(&info->cmap);
+ return -EINVAL;
+ }
+
+ if (fsl_diu_set_par(info)) {
+ printk(KERN_ERR "fb_set_par failed");
+ fb_dealloc_cmap(&info->cmap);
+ return -EINVAL;
+ }
+
+ if (register_framebuffer(info) < 0) {
+ printk(KERN_ERR "register_framebuffer failed");
+ unmap_video_memory(info);
+ fb_dealloc_cmap(&info->cmap);
+ return -EINVAL;
+ }
+
+ mfbi->registered = 1;
+ printk(KERN_INFO "fb%d: %s fb device registered successfully.\n",
+ info->node, info->fix.id);
+
+ return 0;
+}
+
+static void __exit uninstall_fb(struct fb_info *info)
+{
+ struct mfb_info *mfbi = info->par;
+
+ if (!mfbi->registered)
+ return;
+
+ unregister_framebuffer(info);
+ unmap_video_memory(info);
+ if (&info->cmap)
+ fb_dealloc_cmap(&info->cmap);
+
+ mfbi->registered = 0;
+}
+
+static irqreturn_t fsl_diu_isr(int irq, void *dev_id)
+{
+ struct diu *hw = dr.diu_reg;
+ unsigned int status = in_be32(&(hw->int_status));
+
+ if (status) {
+ /* This is the workaround for underrun */
+ if (status & INT_UNDRUN) {
+ out_be32(&(hw->diu_mode), 0);
+ pr_debug("Err: DIU occurs underrun!\n");
+ udelay(1);
+ out_be32(&(hw->diu_mode), 1);
+ }
+#if defined(CONFIG_NOT_COHERENT_CACHE)
+ else if (status & INT_VSYNC) {
+ unsigned int i;
+ for (i = 0; i < coherence_data_size;
+ i += d_cache_line_size)
+ __asm__ __volatile__ (
+ "dcbz 0, %[input]"
+ ::[input]"r"(&coherence_data[i]));
+ }
+#endif
+ return IRQ_HANDLED;
+ }
+ return IRQ_NONE;
+}
+
+static int request_irq_local(int irq)
+{
+ unsigned long status, ints;
+ struct diu *hw;
+ int ret;
+
+ hw = dr.diu_reg;
+
+ /* Read to clear the status */
+ status = in_be32(&(hw->int_status));
+
+ ret = request_irq(irq, fsl_diu_isr, 0, "diu", 0);
+ if (ret)
+ pr_info("Request diu IRQ failed.\n");
+ else {
+ ints = INT_PARERR | INT_LS_BF_VS;
+#if !defined(CONFIG_NOT_COHERENT_CACHE)
+ ints |= INT_VSYNC;
+#endif
+ if (dr.mode == MFB_MODE2 || dr.mode == MFB_MODE3)
+ ints |= INT_VSYNC_WB;
+
+ /* Read to clear the status */
+ status = in_be32(&(hw->int_status));
+ out_be32(&(hw->int_mask), ints);
+ }
+ return ret;
+}
+
+static void free_irq_local(int irq)
+{
+ struct diu *hw = dr.diu_reg;
+
+ /* Disable all LCDC interrupt */
+ out_be32(&(hw->int_mask), 0x1f);
+
+ free_irq(irq, 0);
+}
+
+#ifdef CONFIG_PM
+/*
+ * Power management hooks. Note that we won't be called from IRQ context,
+ * unlike the blank functions above, so we may sleep.
+ */
+static int fsl_diu_suspend(struct of_device *dev, pm_message_t state)
+{
+ struct fsl_diu_data *machine_data;
+
+ machine_data = dev_get_drvdata(&ofdev->dev);
+ disable_lcdc(machine_data->fsl_diu_info[0]);
+
+ return 0;
+}
+
+static int fsl_diu_resume(struct of_device *dev)
+{
+ struct fsl_diu_data *machine_data;
+
+ machine_data = dev_get_drvdata(&ofdev->dev);
+ enable_lcdc(machine_data->fsl_diu_info[0]);
+
+ return 0;
+}
+
+#else
+#define fsl_diu_suspend NULL
+#define fsl_diu_resume NULL
+#endif /* CONFIG_PM */
+
+/* Align to 64-bit(8-byte), 32-byte, etc. */
+static int allocate_buf(struct diu_addr *buf, u32 size, u32 bytes_align)
+{
+ u32 offset, ssize;
+ u32 mask;
+ dma_addr_t paddr = 0;
+
+ ssize = size + bytes_align;
+ buf->vaddr = dma_alloc_coherent(0, ssize, &paddr, GFP_DMA | __GFP_ZERO);
+ if (!buf->vaddr)
+ return -ENOMEM;
+
+ buf->paddr = (__u32) paddr;
+
+ mask = bytes_align - 1;
+ offset = (u32)buf->paddr & mask;
+ if (offset) {
+ buf->offset = bytes_align - offset;
+ buf->paddr = (u32)buf->paddr + offset;
+ } else
+ buf->offset = 0;
+ return 0;
+}
+
+static void free_buf(struct diu_addr *buf, u32 size, u32 bytes_align)
+{
+ dma_free_coherent(0, size + bytes_align,
+ buf->vaddr, (buf->paddr - buf->offset));
+ return;
+}
+
+static ssize_t store_monitor(struct device *device,
+ struct device_attribute *attr, const char *buf, size_t count)
+{
+ int old_monitor_port;
+ unsigned long val;
+ struct fsl_diu_data *machine_data =
+ container_of(attr, struct fsl_diu_data, dev_attr);
+
+ if (strict_strtoul(buf, 10, &val))
+ return 0;
+
+ old_monitor_port = machine_data->monitor_port;
+ machine_data->monitor_port = diu_ops.set_sysfs_monitor_port(val);
+
+ if (old_monitor_port != machine_data->monitor_port) {
+ /* All AOIs need adjust pixel format
+ * fsl_diu_set_par only change the pixsel format here
+ * unlikely to fail. */
+ fsl_diu_set_par(machine_data->fsl_diu_info[0]);
+ fsl_diu_set_par(machine_data->fsl_diu_info[1]);
+ fsl_diu_set_par(machine_data->fsl_diu_info[2]);
+ fsl_diu_set_par(machine_data->fsl_diu_info[3]);
+ fsl_diu_set_par(machine_data->fsl_diu_info[4]);
+ }
+ return count;
+}
+
+static ssize_t show_monitor(struct device *device,
+ struct device_attribute *attr, char *buf)
+{
+ struct fsl_diu_data *machine_data =
+ container_of(attr, struct fsl_diu_data, dev_attr);
+ return diu_ops.show_monitor_port(machine_data->monitor_port, buf);
+}
+
+static int fsl_diu_probe(struct of_device *ofdev,
+ const struct of_device_id *match)
+{
+ struct device_node *np = ofdev->node;
+ struct mfb_info *mfbi;
+ phys_addr_t dummy_ad_addr;
+ int ret, i, error = 0;
+ struct resource res;
+ struct fsl_diu_data *machine_data;
+
+ machine_data = kzalloc(sizeof(struct fsl_diu_data), GFP_KERNEL);
+ if (!machine_data)
+ return -ENOMEM;
+
+ for (i = 0; i < ARRAY_SIZE(machine_data->fsl_diu_info); i++) {
+ machine_data->fsl_diu_info[i] =
+ framebuffer_alloc(sizeof(struct mfb_info), &ofdev->dev);
+ if (!machine_data->fsl_diu_info[i]) {
+ dev_err(&ofdev->dev, "cannot allocate memory\n");
+ ret = -ENOMEM;
+ goto error2;
+ }
+ mfbi = machine_data->fsl_diu_info[i]->par;
+ memcpy(mfbi, &mfb_template[i], sizeof(struct mfb_info));
+ mfbi->parent = machine_data;
+ }
+
+ ret = of_address_to_resource(np, 0, &res);
+ if (ret) {
+ dev_err(&ofdev->dev, "could not obtain DIU address\n");
+ goto error;
+ }
+ if (!res.start) {
+ dev_err(&ofdev->dev, "invalid DIU address\n");
+ goto error;
+ }
+ dev_dbg(&ofdev->dev, "%s, res.start: 0x%08x\n", __func__, res.start);
+
+ dr.diu_reg = ioremap(res.start, sizeof(struct diu));
+ if (!dr.diu_reg) {
+ dev_err(&ofdev->dev, "Err: can't map DIU registers!\n");
+ ret = -EFAULT;
+ goto error2;
+ }
+
+ out_be32(&(dr.diu_reg->diu_mode), 0); /* disable DIU anyway*/
+
+ /* Get the IRQ of the DIU */
+ machine_data->irq = irq_of_parse_and_map(np, 0);
+
+ if (!machine_data->irq) {
+ dev_err(&ofdev->dev, "could not get DIU IRQ\n");
+ ret = -EINVAL;
+ goto error;
+ }
+ machine_data->monitor_port = monitor_port;
+
+ /* Area descriptor memory pool aligns to 64-bit boundary */
+ if (allocate_buf(&pool.ad, sizeof(struct diu_ad) * FSL_AOI_NUM, 8))
+ return -ENOMEM;
+
+ /* Get memory for Gamma Table - 32-byte aligned memory */
+ if (allocate_buf(&pool.gamma, 768, 32)) {
+ ret = -ENOMEM;
+ goto error;
+ }
+
+ /* For performance, cursor bitmap buffer aligns to 32-byte boundary */
+ if (allocate_buf(&pool.cursor, MAX_CURS * MAX_CURS * 2, 32)) {
+ ret = -ENOMEM;
+ goto error;
+ }
+
+ i = ARRAY_SIZE(machine_data->fsl_diu_info);
+ machine_data->dummy_ad = (struct diu_ad *)
+ ((u32)pool.ad.vaddr + pool.ad.offset) + i;
+ machine_data->dummy_ad->paddr = pool.ad.paddr +
+ i * sizeof(struct diu_ad);
+ machine_data->dummy_aoi_virt = fsl_diu_alloc(64, &dummy_ad_addr);
+ if (!machine_data->dummy_aoi_virt) {
+ ret = -ENOMEM;
+ goto error;
+ }
+ machine_data->dummy_ad->addr = cpu_to_le32(dummy_ad_addr);
+ machine_data->dummy_ad->pix_fmt = 0x88882317;
+ machine_data->dummy_ad->src_size_g_alpha = cpu_to_le32((4 << 12) | 4);
+ machine_data->dummy_ad->aoi_size = cpu_to_le32((4 << 16) | 2);
+ machine_data->dummy_ad->offset_xyi = 0;
+ machine_data->dummy_ad->offset_xyd = 0;
+ machine_data->dummy_ad->next_ad = 0;
+
+ out_be32(&(dr.diu_reg->desc[0]), machine_data->dummy_ad->paddr);
+ out_be32(&(dr.diu_reg->desc[1]), machine_data->dummy_ad->paddr);
+ out_be32(&(dr.diu_reg->desc[2]), machine_data->dummy_ad->paddr);
+
+ for (i = 0; i < ARRAY_SIZE(machine_data->fsl_diu_info); i++) {
+ machine_data->fsl_diu_info[i]->fix.smem_start = 0;
+ mfbi = machine_data->fsl_diu_info[i]->par;
+ mfbi->ad = (struct diu_ad *)((u32)pool.ad.vaddr
+ + pool.ad.offset) + i;
+ mfbi->ad->paddr = pool.ad.paddr + i * sizeof(struct diu_ad);
+ ret = install_fb(machine_data->fsl_diu_info[i]);
+ if (ret) {
+ dev_err(&ofdev->dev,
+ "Failed to register framebuffer %d\n",
+ i);
+ goto error;
+ }
+ }
+
+ if (request_irq_local(machine_data->irq)) {
+ dev_err(machine_data->fsl_diu_info[0]->dev,
+ "could not request irq for diu.");
+ goto error;
+ }
+
+ machine_data->dev_attr.attr.name = "monitor";
+ machine_data->dev_attr.attr.mode = S_IRUGO|S_IWUSR;
+ machine_data->dev_attr.show = show_monitor;
+ machine_data->dev_attr.store = store_monitor;
+ error = device_create_file(machine_data->fsl_diu_info[0]->dev,
+ &machine_data->dev_attr);
+ if (error) {
+ dev_err(machine_data->fsl_diu_info[0]->dev,
+ "could not create sysfs %s file\n",
+ machine_data->dev_attr.attr.name);
+ }
+
+ dev_set_drvdata(&ofdev->dev, machine_data);
+ return 0;
+
+error:
+ for (i = ARRAY_SIZE(machine_data->fsl_diu_info);
+ i > 0; i--)
+ uninstall_fb(machine_data->fsl_diu_info[i - 1]);
+ if (pool.ad.vaddr)
+ free_buf(&pool.ad, sizeof(struct diu_ad) * FSL_AOI_NUM, 8);
+ if (pool.gamma.vaddr)
+ free_buf(&pool.gamma, 768, 32);
+ if (pool.cursor.vaddr)
+ free_buf(&pool.cursor, MAX_CURS * MAX_CURS * 2, 32);
+ if (machine_data->dummy_aoi_virt)
+ fsl_diu_free(machine_data->dummy_aoi_virt, 64);
+ iounmap(dr.diu_reg);
+
+error2:
+ for (i = 0; i < ARRAY_SIZE(machine_data->fsl_diu_info); i++)
+ if (machine_data->fsl_diu_info[i])
+ framebuffer_release(machine_data->fsl_diu_info[i]);
+ kfree(machine_data);
+
+ return ret;
+}
+
+
+static int fsl_diu_remove(struct of_device *ofdev)
+{
+ struct fsl_diu_data *machine_data;
+ int i;
+
+ machine_data = dev_get_drvdata(&ofdev->dev);
+ disable_lcdc(machine_data->fsl_diu_info[0]);
+ free_irq_local(machine_data->irq);
+ for (i = ARRAY_SIZE(machine_data->fsl_diu_info); i > 0; i--)
+ uninstall_fb(machine_data->fsl_diu_info[i - 1]);
+ if (pool.ad.vaddr)
+ free_buf(&pool.ad, sizeof(struct diu_ad) * FSL_AOI_NUM, 8);
+ if (pool.gamma.vaddr)
+ free_buf(&pool.gamma, 768, 32);
+ if (pool.cursor.vaddr)
+ free_buf(&pool.cursor, MAX_CURS * MAX_CURS * 2, 32);
+ if (machine_data->dummy_aoi_virt)
+ fsl_diu_free(machine_data->dummy_aoi_virt, 64);
+ iounmap(dr.diu_reg);
+ for (i = 0; i < ARRAY_SIZE(machine_data->fsl_diu_info); i++)
+ if (machine_data->fsl_diu_info[i])
+ framebuffer_release(machine_data->fsl_diu_info[i]);
+ kfree(machine_data);
+
+ return 0;
+}
+
+#ifndef MODULE
+static int __init fsl_diu_setup(char *options)
+{
+ char *opt;
+ unsigned long val;
+
+ if (!options || !*options)
+ return 0;
+
+ while ((opt = strsep(&options, ",")) != NULL) {
+ if (!*opt)
+ continue;
+ if (!strncmp(opt, "monitor=", 8)) {
+ if (!strict_strtoul(opt + 8, 10, &val) && (val <= 2))
+ monitor_port = val;
+ } else if (!strncmp(opt, "bpp=", 4)) {
+ if (!strict_strtoul(opt + 4, 10, &val))
+ default_bpp = val;
+ } else
+ fb_mode = opt;
+ }
+
+ return 0;
+}
+#endif
+
+static struct of_device_id fsl_diu_match[] = {
+ {
+ .compatible = "fsl,diu",
+ },
+ {}
+};
+MODULE_DEVICE_TABLE(of, fsl_diu_match);
+
+static struct of_platform_driver fsl_diu_driver = {
+ .owner = THIS_MODULE,
+ .name = "fsl_diu",
+ .match_table = fsl_diu_match,
+ .probe = fsl_diu_probe,
+ .remove = fsl_diu_remove,
+ .suspend = fsl_diu_suspend,
+ .resume = fsl_diu_resume,
+};
+
+static int __init fsl_diu_init(void)
+{
+#ifdef CONFIG_NOT_COHERENT_CACHE
+ struct device_node *np;
+ const u32 *prop;
+#endif
+ int ret;
+#ifndef MODULE
+ char *option;
+
+ /*
+ * For kernel boot options (in 'video=xxxfb:<options>' format)
+ */
+ if (fb_get_options("fslfb", &option))
+ return -ENODEV;
+ fsl_diu_setup(option);
+#endif
+ printk(KERN_INFO "Freescale DIU driver\n");
+
+#ifdef CONFIG_NOT_COHERENT_CACHE
+ np = of_find_node_by_type(NULL, "cpu");
+ if (!np) {
+ printk(KERN_ERR "Err: can't find device node 'cpu'\n");
+ return -ENODEV;
+ }
+
+ prop = of_get_property(np, "d-cache-size", NULL);
+ if (prop == NULL)
+ return -ENODEV;
+
+ /* Freescale PLRU requires 13/8 times the cache size to do a proper
+ displacement flush
+ */
+ coherence_data_size = *prop * 13;
+ coherence_data_size /= 8;
+
+ prop = of_get_property(np, "d-cache-line-size", NULL);
+ if (prop == NULL)
+ return -ENODEV;
+ d_cache_line_size = *prop;
+
+ of_node_put(np);
+ coherence_data = vmalloc(coherence_data_size);
+ if (!coherence_data)
+ return -ENOMEM;
+#endif
+ ret = of_register_platform_driver(&fsl_diu_driver);
+ if (ret) {
+ printk(KERN_ERR
+ "fsl-diu: failed to register platform driver\n");
+#if defined(CONFIG_NOT_COHERENT_CACHE)
+ vfree(coherence_data);
+#endif
+ iounmap(dr.diu_reg);
+ }
+ return ret;
+}
+
+static void __exit fsl_diu_exit(void)
+{
+ of_unregister_platform_driver(&fsl_diu_driver);
+#if defined(CONFIG_NOT_COHERENT_CACHE)
+ vfree(coherence_data);
+#endif
+}
+
+module_init(fsl_diu_init);
+module_exit(fsl_diu_exit);
+
+MODULE_AUTHOR("York Sun <yorksun@freescale.com>");
+MODULE_DESCRIPTION("Freescale DIU framebuffer driver");
+MODULE_LICENSE("GPL");
+
+module_param_named(mode, fb_mode, charp, 0);
+MODULE_PARM_DESC(mode,
+ "Specify resolution as \"<xres>x<yres>[-<bpp>][@<refresh>]\" ");
+module_param_named(bpp, default_bpp, ulong, 0);
+MODULE_PARM_DESC(bpp, "Specify bit-per-pixel if not specified mode");
+module_param_named(monitor, monitor_port, int, 0);
+MODULE_PARM_DESC(monitor,
+ "Specify the monitor port (0, 1 or 2) if supported by the platform");
+
diff --git a/drivers/video/fsl-diu-fb.h b/drivers/video/fsl-diu-fb.h
new file mode 100644
index 0000000..fc295d7
--- /dev/null
+++ b/drivers/video/fsl-diu-fb.h
@@ -0,0 +1,223 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * Freescale DIU Frame Buffer device driver
+ *
+ * Authors: Hongjun Chen <hong-jun.chen@freescale.com>
+ * Paul Widmer <paul.widmer@freescale.com>
+ * Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
+ * York Sun <yorksun@freescale.com>
+ *
+ * Based on imxfb.c Copyright (C) 2004 S.Hauer, Pengutronix
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+
+#ifndef __FSL_DIU_FB_H__
+#define __FSL_DIU_FB_H__
+
+/* Arbitrary threshold to determine the allocation method
+ * See mpc8610fb_set_par(), map_video_memory(), and unmap_video_memory()
+ */
+#define MEM_ALLOC_THRESHOLD (1024*768*4+32)
+/* Minimum value that the pixel clock can be set to in pico seconds
+ * This is determined by platform clock/3 where the minimum platform
+ * clock is 533MHz. This gives 5629 pico seconds.
+ */
+#define MIN_PIX_CLK 5629
+#define MAX_PIX_CLK 96096
+
+#include <linux/types.h>
+
+struct mfb_alpha {
+ int enable;
+ int alpha;
+};
+
+struct mfb_chroma_key {
+ int enable;
+ __u8 red_max;
+ __u8 green_max;
+ __u8 blue_max;
+ __u8 red_min;
+ __u8 green_min;
+ __u8 blue_min;
+};
+
+struct aoi_display_offset {
+ int x_aoi_d;
+ int y_aoi_d;
+};
+
+#define MFB_SET_CHROMA_KEY _IOW('M', 1, struct mfb_chroma_key)
+#define MFB_WAIT_FOR_VSYNC _IOW('F', 0x20, u_int32_t)
+#define MFB_SET_BRIGHTNESS _IOW('M', 3, __u8)
+
+#define MFB_SET_ALPHA 0x80014d00
+#define MFB_GET_ALPHA 0x40014d00
+#define MFB_SET_AOID 0x80084d04
+#define MFB_GET_AOID 0x40084d04
+#define MFB_SET_PIXFMT 0x80014d08
+#define MFB_GET_PIXFMT 0x40014d08
+
+#define FBIOGET_GWINFO 0x46E0
+#define FBIOPUT_GWINFO 0x46E1
+
+#ifdef __KERNEL__
+#include <linux/spinlock.h>
+
+/*
+ * These are the fields of area descriptor(in DDR memory) for every plane
+ */
+struct diu_ad {
+ /* Word 0(32-bit) in DDR memory */
+/* __u16 comp; */
+/* __u16 pixel_s:2; */
+/* __u16 pallete:1; */
+/* __u16 red_c:2; */
+/* __u16 green_c:2; */
+/* __u16 blue_c:2; */
+/* __u16 alpha_c:3; */
+/* __u16 byte_f:1; */
+/* __u16 res0:3; */
+
+ __be32 pix_fmt; /* hard coding pixel format */
+
+ /* Word 1(32-bit) in DDR memory */
+ __le32 addr;
+
+ /* Word 2(32-bit) in DDR memory */
+/* __u32 delta_xs:11; */
+/* __u32 res1:1; */
+/* __u32 delta_ys:11; */
+/* __u32 res2:1; */
+/* __u32 g_alpha:8; */
+ __le32 src_size_g_alpha;
+
+ /* Word 3(32-bit) in DDR memory */
+/* __u32 delta_xi:11; */
+/* __u32 res3:5; */
+/* __u32 delta_yi:11; */
+/* __u32 res4:3; */
+/* __u32 flip:2; */
+ __le32 aoi_size;
+
+ /* Word 4(32-bit) in DDR memory */
+ /*__u32 offset_xi:11;
+ __u32 res5:5;
+ __u32 offset_yi:11;
+ __u32 res6:5;
+ */
+ __le32 offset_xyi;
+
+ /* Word 5(32-bit) in DDR memory */
+ /*__u32 offset_xd:11;
+ __u32 res7:5;
+ __u32 offset_yd:11;
+ __u32 res8:5; */
+ __le32 offset_xyd;
+
+
+ /* Word 6(32-bit) in DDR memory */
+ __u8 ckmax_r;
+ __u8 ckmax_g;
+ __u8 ckmax_b;
+ __u8 res9;
+
+ /* Word 7(32-bit) in DDR memory */
+ __u8 ckmin_r;
+ __u8 ckmin_g;
+ __u8 ckmin_b;
+ __u8 res10;
+/* __u32 res10:8; */
+
+ /* Word 8(32-bit) in DDR memory */
+ __le32 next_ad;
+
+ /* Word 9(32-bit) in DDR memory, just for 64-bit aligned */
+ __u32 paddr;
+} __attribute__ ((packed));
+
+/* DIU register map */
+struct diu {
+ __be32 desc[3];
+ __be32 gamma;
+ __be32 pallete;
+ __be32 cursor;
+ __be32 curs_pos;
+ __be32 diu_mode;
+ __be32 bgnd;
+ __be32 bgnd_wb;
+ __be32 disp_size;
+ __be32 wb_size;
+ __be32 wb_mem_addr;
+ __be32 hsyn_para;
+ __be32 vsyn_para;
+ __be32 syn_pol;
+ __be32 thresholds;
+ __be32 int_status;
+ __be32 int_mask;
+ __be32 colorbar[8];
+ __be32 filling;
+ __be32 plut;
+} __attribute__ ((packed));
+
+struct diu_hw {
+ struct diu *diu_reg;
+ spinlock_t reg_lock;
+
+ __u32 mode; /* DIU operation mode */
+};
+
+struct diu_addr {
+ __u8 __iomem *vaddr; /* Virtual address */
+ dma_addr_t paddr; /* Physical address */
+ __u32 offset;
+};
+
+struct diu_pool {
+ struct diu_addr ad;
+ struct diu_addr gamma;
+ struct diu_addr pallete;
+ struct diu_addr cursor;
+};
+
+#define FSL_DIU_BASE_OFFSET 0x2C000 /* Offset of DIU */
+#define INT_LCDC 64 /* DIU interrupt number */
+
+#define FSL_AOI_NUM 6 /* 5 AOIs and one dummy AOI */
+ /* 1 for plane 0, 2 for plane 1&2 each */
+
+/* Minimum X and Y resolutions */
+#define MIN_XRES 64
+#define MIN_YRES 64
+
+/* HW cursor parameters */
+#define MAX_CURS 32
+
+/* Modes of operation of DIU */
+#define MFB_MODE0 0 /* DIU off */
+#define MFB_MODE1 1 /* All three planes output to display */
+#define MFB_MODE2 2 /* Plane 1 to display, planes 2+3 written back*/
+#define MFB_MODE3 3 /* All three planes written back to memory */
+#define MFB_MODE4 4 /* Color bar generation */
+
+/* INT_STATUS/INT_MASK field descriptions */
+#define INT_VSYNC 0x01 /* Vsync interrupt */
+#define INT_VSYNC_WB 0x02 /* Vsync interrupt for write back operation */
+#define INT_UNDRUN 0x04 /* Under run exception interrupt */
+#define INT_PARERR 0x08 /* Display parameters error interrupt */
+#define INT_LS_BF_VS 0x10 /* Lines before vsync. interrupt */
+
+/* Panels'operation modes */
+#define MFB_TYPE_OUTPUT 0 /* Panel output to display */
+#define MFB_TYPE_OFF 1 /* Panel off */
+#define MFB_TYPE_WB 2 /* Panel written back to memory */
+#define MFB_TYPE_TEST 3 /* Panel generate color bar */
+
+#endif /* __KERNEL__ */
+#endif /* __FSL_DIU_FB_H__ */
--
1.5.2.2


\
 
 \ /
  Last update: 2008-03-28 03:51    [from the cache]
©2003-2014 Jasper Spaans. Advertise on this site