lkml.org 
[lkml]   [2008]   [Feb]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Date
Subject[PATCH 05/12] cmd640: init hwif->{io_ports,irq} explicitly
Do explicit port setup instead of depending on init_ide_data().

This way hwif->io_ports[] and hwif->irq are always correctly set
regardless of CONFIG_PCI / CONFIG_BLK_DEV_IDEPCI.

[ Remember to not break "idex=noprobe" parameter. ]

While at it fix printk().

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
---
drivers/ide/pci/cmd640.c | 23 ++++++++++++++++++++---
1 file changed, 20 insertions(+), 3 deletions(-)

Index: b/drivers/ide/pci/cmd640.c
===================================================================
--- a/drivers/ide/pci/cmd640.c
+++ b/drivers/ide/pci/cmd640.c
@@ -712,8 +712,9 @@ static int __init cmd640x_init(void)
int second_port_cmd640 = 0;
const char *bus_type, *port2;
unsigned int index;
- u8 b, cfr;
+ u8 b, cfr, oldnoprobe;
u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
+ hw_regs_t hw[2];

if (cmd640_vlb && probe_for_cmd640_vlb()) {
bus_type = "VLB";
@@ -752,12 +753,25 @@ static int __init cmd640x_init(void)
return 0;
}

+ memset(&hw, 0, sizeof(hw));
+
+ ide_std_init_ports(&hw[0], 0x1f0, 0x3f6);
+ hw[0].irq = 14;
+
+ ide_std_init_ports(&hw[1], 0x170, 0x376);
+ hw[1].irq = 15;
+
+ printk(KERN_INFO "cmd640: buggy cmd640%c interface on %s, config=0x%02x"
+ "\n", 'a' + cmd640_chip_version - 1, bus_type, cfr);
+
/*
* Initialize data for primary port
*/
setup_device_ptrs ();
- printk("%s: buggy cmd640%c interface on %s, config=0x%02x\n",
- cmd_hwif0->name, 'a' + cmd640_chip_version - 1, bus_type, cfr);
+
+ oldnoprobe = cmd_hwif0->noprobe;
+ ide_init_port_hw(cmd_hwif0, &hw[0]);
+ cmd_hwif0->noprobe = oldnoprobe;
#ifdef CONFIG_BLK_DEV_CMD640_ENHANCED
cmd_hwif0->set_pio_mode = &cmd640_set_pio_mode;
#endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */
@@ -809,6 +823,9 @@ static int __init cmd640x_init(void)
* Initialize data for secondary cmd640 port, if enabled
*/
if (second_port_cmd640) {
+ oldnoprobe = cmd_hwif1->noprobe;
+ ide_init_port_hw(cmd_hwif1, &hw[1]);
+ cmd_hwif1->noprobe = oldnoprobe;
#ifdef CONFIG_BLK_DEV_CMD640_ENHANCED
cmd_hwif1->set_pio_mode = &cmd640_set_pio_mode;
#endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */

\
 
 \ /
  Last update: 2008-02-16 17:29    [W:0.107 / U:1.524 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site