lkml.org 
[lkml]   [2008]   [Dec]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[PATCH 5/13] drivers/mtd/nand: use USB API functions rather than constants
From: Julia Lawall <julia@diku.dk>

This set of patches introduces calls to the following set of functions:

usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)

In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:

USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC

An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@

- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)

@r5@ struct usb_endpoint_descriptor *epd; @@

- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
- \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)

@inc@
@@

#include <linux/usb.h>

@depends on !inc && (r1||r5)@
@@

+ #include <linux/usb.h>
#include <linux/usb/...>
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>

---
drivers/mtd/nand/alauda.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/mtd/nand/alauda.c b/drivers/mtd/nand/alauda.c
index 9623803..6d96491 100644
--- a/drivers/mtd/nand/alauda.c
+++ b/drivers/mtd/nand/alauda.c
@@ -676,11 +676,11 @@ static int alauda_probe(struct usb_interface *interface,
goto error;

al->write_out = usb_sndbulkpipe(al->dev,
- ep_wr->bEndpointAddress & USB_ENDPOINT_NUMBER_MASK);
+ usb_endpoint_num(ep_wr));
al->bulk_in = usb_rcvbulkpipe(al->dev,
- ep_in->bEndpointAddress & USB_ENDPOINT_NUMBER_MASK);
+ usb_endpoint_num(ep_in));
al->bulk_out = usb_sndbulkpipe(al->dev,
- ep_out->bEndpointAddress & USB_ENDPOINT_NUMBER_MASK);
+ usb_endpoint_num(ep_out));

/* second device is identical up to now */
memcpy(al+1, al, sizeof(*al));

\
 
 \ /
  Last update: 2008-12-29 11:25    [W:0.025 / U:0.164 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site