lkml.org 
[lkml]   [2008]   [Dec]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: FPGA programming driver architecture
On Sat, 13 Dec 2008 13:58:01 +0100
Florian Fainelli <florian@openwrt.org> wrote:

> (CC'ing linux-embedded)
>
> Salut Hugo,
>
> Le Friday 12 December 2008 21:03:14 Hugo Villeneuve, vous avez écrit :
> > Hi,
> > I have written some code to program a FPGA in Linux, for two
> > different types of boards: one uses a serial interface (SPI) and
> > the second a parallel interface. I have been able to sucessfully
> > program both boards. I'm now trying to clean my code and make it
> > more generic, as well as better in line with the Linux driver
> > model. I would also like to include it in the mainline kernel if
> > there is interest.
>
> Is it a platform-driver ? What do you provide in platform_data ?

Hi Florian,
Yes, currently it is a platform driver. Here is my platform data:

static struct fpgaload_pdata_t fpgaload_pdata = {
.fpga_family = FPGA_FAMILY_XILINX_XC3S,
.payload_full_size = XC3S1400A_PAYLOAD_SIZE,
.program_b = GPIO(21),
.done = GPIO(19),
.init_b = GPIO(20),
.swapbits = 0,
.interface = FPGALOAD_INTERFACE_SERIAL,
.bitstream_name = "fpga.bit",
};

> > Here is a description of the current architecture (refer to diagrams
> > below): The fpgaload module controls one output GPIOs (PROG), and
> > two input GPIOs (INIT and DONE). These GPIOs are specified in board
> > setup code. Both fpgaload_ser and fpgaload_par modules export a
> > single function to write a byte. The fpgaload driver is a char
> > device to which we can write (/dev/fpgaload) to program a bitstream
> > (FPGA firmware) inside the FPGA.
>
> You should probably consider using request_firmware to load the
> bitstream from the userspace and possibly add a /sys interface to
> export some attributes like :

This is already the case with request_firmware :) The bitstream_name field in platform data is used to specify the name of the file.

> - GPIOs being used between the host and the FPGA
> - status (i.e : programmed, not programmed ...)
> - FPGA vendor, type ...
>
> > The
> > fpgaload driver will toggle the GPIOs to initiate programming and
> > the then call the corresponding write_byte function based on the
> > interface type specified in board setup code (serial or parallel,
> > or any future interface desired).
>
> > The problem with that approach is that when loading the fpgaload
> > module with modprobe, it will automatically try to load the
> > fpgaload_ser and fpgaload_par modules, even if only serial
> > interface was specified in board setup code for example. This is
> > not good when building a kernel for similar but different boards.
>
> What about something like that :
>
> - fpgaload-core which contains all the code that can be shared
> between the drivers like requesting firmware, providing sysfs
> attributes,
> - fpgaload-spi would handle the low-level SPI connection
> - fpgaload-par would handle the low-level parallel connection

This is pretty much like that right now, exceptfor sysfs attributes.

> fpgaload-ser and par would register with fpgaload-core and they could
> register a fpga loading callback which is low-level specific for
> instance. Platform code would instantiate the core driver. That way,
> adding support for other loading protocols like slave serial or
> master serial can be done easily.

Yes, I think this could work, but I would like to know what kind of driver fpgaload-core would be. Currently it is a platform driver and a chardev (to support open and write methods for programming). How shall I implement it? Bus driver, platform driver?

Ciao, Hugo V.
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2008-12-15 19:19    [W:0.058 / U:0.480 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site