lkml.org 
[lkml]   [2008]   [Oct]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: e1000e: sporadic "hardware error"s with Intel 82563EB on Supermicro X7DB3
Hello!

Krzysztof Halasa wrote:
> Hi,
>
> "Hillier, Gernot" <gernot.hillier@siemens.com> writes:
>
>> On at least two machines using the Supermicro X7DB3 board with Intel
>> 82563EB (a.k.a. PCI device 8086:1096), we see sporadic problems on modprobe
>> (about 1 time in some hundred tries):
>>
>> e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k2
>> e1000e: Copyright (c) 1999-2008 Intel Corporation.
>> e1000e 0000:06:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
>> e1000e 0000:06:00.0: setting latency timer to 64
>> 0000:06:00.0: 0000:06:00.0: Hardware Error
>
> What does "lspci -vv" say about it when the above happens?
>
> I spurious chip reset (hardware) could probably cause that.

Here's the output of "lspci -vv" in the error case (for the eth devices):

------- SNIP -----------
06:00.0 Class 0200: Device 8086:1096 (rev 01)
Subsystem: Device 15d9:1096
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at d0020000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at d0000000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 4000 [size=32]
[virtual] Expansion ROM at d0080000 [disabled] [size=64K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 00000000feeff00c Data: 4158
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM unknown, Latency L0 <128ns, L1 <64us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [140] Device Serial Number 06-c7-66-ff-ff-48-30-00
Kernel driver in use: e1000e
Kernel modules: e1000e

06:00.1 Class 0200: Device 8086:1096 (rev 01)
Subsystem: Device 15d9:1096
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at d0060000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at d0040000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 4020 [size=32]
[virtual] Expansion ROM at d0090000 [disabled] [size=64K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM unknown, Latency L0 <128ns, L1 <64us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [140] Device Serial Number 06-c7-66-ff-ff-48-30-00
Kernel driver in use: e1000e
Kernel modules: e1000e
------- SNIP -----------

Retried this several times in the error and normal case. The only things
which change are three values for device 06:00.0:

- Control "DisINTx-" changes to "DisINTx+" if the card is correctly
initialized
- Interrupt changes from IRQ 18 to IRQ 4345 if card is correctly initialized
- Message Signalled Interrupts change from "Enable-" to "Enable+"

In addition, the "Data" field from "Message Signalled Interrupts" seems to
change w/o any clear pattern.

For 06:00.1, everything seems to be the same in the error as well as in the
normal case.

Does this tell you anything valuable?

--
Gernot Hillier, Siemens AG, CT SE 2


\
 
 \ /
  Last update: 2008-10-08 15:33    [W:0.059 / U:0.052 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site