lkml.org 
[lkml]   [2008]   [Oct]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[patch 09/17] OHCI: Allow broken controllers to auto-stop
2.6.27-stable review patch.  If anyone has any objections, please let us
know.

------------------
From: Alan Stern <stern@rowland.harvard.edu>

commit 4a511bc3f5829bc18428bcf11c25417a79d09396 upstream

This patch (as1134) attempts to improve the way we handle OHCI
controllers with broken Root Hub Status Change interrupt support. In
these controllers the RHSC interrupt bit essentially never turns off,
making RHSC interrupts useless -- they have to remain permanently
disabled.

Such controllers should still be allowed to turn off their root hubs
when no devices are attached. Polling for new connections can
continue while the root hub is suspended. The patch implements this
feature. (It won't have much effect unless CONFIG_PM is enabled and
CONFIG_USB_SUSPEND is disabled, but since the overhead is very small
we may as well do it.)

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

---
drivers/usb/host/ohci-hub.c | 60 +++++++++++++++++++++++---------------------
1 file changed, 32 insertions(+), 28 deletions(-)

--- a/drivers/usb/host/ohci-hub.c
+++ b/drivers/usb/host/ohci-hub.c
@@ -362,18 +362,23 @@ static int ohci_root_hub_state_changes(s
int any_connected)
{
int poll_rh = 1;
- int rhsc;
+ int rhsc_status, rhsc_enable;

- rhsc = ohci_readl(ohci, &ohci->regs->intrenable) & OHCI_INTR_RHSC;
- switch (ohci->hc_control & OHCI_CTRL_HCFS) {
+ /* Some broken controllers never turn off RHCS in the interrupt
+ * status register. For their sake we won't re-enable RHSC
+ * interrupts if the interrupt bit is already active.
+ */
+ rhsc_status = ohci_readl(ohci, &ohci->regs->intrstatus) &
+ OHCI_INTR_RHSC;
+ rhsc_enable = ohci_readl(ohci, &ohci->regs->intrenable) &
+ OHCI_INTR_RHSC;

+ switch (ohci->hc_control & OHCI_CTRL_HCFS) {
case OHCI_USB_OPER:
- /* If no status changes are pending, enable status-change
- * interrupts.
- */
- if (!rhsc && !changed) {
- rhsc = OHCI_INTR_RHSC;
- ohci_writel(ohci, rhsc, &ohci->regs->intrenable);
+ /* If no status changes are pending, enable RHSC interrupts. */
+ if (!rhsc_enable && !rhsc_status && !changed) {
+ rhsc_enable = OHCI_INTR_RHSC;
+ ohci_writel(ohci, rhsc_enable, &ohci->regs->intrenable);
}

/* Keep on polling until we know a device is connected
@@ -383,7 +388,7 @@ static int ohci_root_hub_state_changes(s
if (any_connected ||
!device_may_wakeup(&ohci_to_hcd(ohci)
->self.root_hub->dev)) {
- if (rhsc)
+ if (rhsc_enable)
poll_rh = 0;
} else {
ohci->autostop = 1;
@@ -396,34 +401,36 @@ static int ohci_root_hub_state_changes(s
ohci->autostop = 0;
ohci->next_statechange = jiffies +
STATECHANGE_DELAY;
- } else if (rhsc && time_after_eq(jiffies,
+ } else if (time_after_eq(jiffies,
ohci->next_statechange)
&& !ohci->ed_rm_list
&& !(ohci->hc_control &
OHCI_SCHED_ENABLES)) {
ohci_rh_suspend(ohci, 1);
- poll_rh = 0;
+ if (rhsc_enable)
+ poll_rh = 0;
}
}
break;

- /* if there is a port change, autostart or ask to be resumed */
case OHCI_USB_SUSPEND:
case OHCI_USB_RESUME:
+ /* if there is a port change, autostart or ask to be resumed */
if (changed) {
if (ohci->autostop)
ohci_rh_resume(ohci);
else
usb_hcd_resume_root_hub(ohci_to_hcd(ohci));
} else {
- if (!rhsc && (ohci->autostop ||
+ if (!rhsc_enable && !rhsc_status && (ohci->autostop ||
ohci_to_hcd(ohci)->self.root_hub->
- do_remote_wakeup))
- ohci_writel(ohci, OHCI_INTR_RHSC,
+ do_remote_wakeup)) {
+ rhsc_enable = OHCI_INTR_RHSC;
+ ohci_writel(ohci, rhsc_enable,
&ohci->regs->intrenable);
-
- /* everything is idle, no need for polling */
- poll_rh = 0;
+ }
+ if (rhsc_enable)
+ poll_rh = 0;
}
break;
}
@@ -443,12 +450,16 @@ static inline int ohci_rh_resume(struct
static int ohci_root_hub_state_changes(struct ohci_hcd *ohci, int changed,
int any_connected)
{
+ int rhsc_status;
+
/* If RHSC is enabled, don't poll */
if (ohci_readl(ohci, &ohci->regs->intrenable) & OHCI_INTR_RHSC)
return 0;

- /* If no status changes are pending, enable status-change interrupts */
- if (!changed) {
+ /* If no status changes are pending, enable RHSC interrupts */
+ rhsc_status = ohci_readl(ohci, &ohci->regs->intrstatus) &
+ OHCI_INTR_RHSC;
+ if (!changed && !rhsc_status) {
ohci_writel(ohci, OHCI_INTR_RHSC, &ohci->regs->intrenable);
return 0;
}
@@ -492,13 +503,6 @@ ohci_hub_status_data (struct usb_hcd *hc
length++;
}

- /* Some broken controllers never turn off RHCS in the interrupt
- * status register. For their sake we won't re-enable RHSC
- * interrupts if the flag is already set.
- */
- if (ohci_readl(ohci, &ohci->regs->intrstatus) & OHCI_INTR_RHSC)
- changed = 1;
-
/* look at each port */
for (i = 0; i < ohci->num_ports; i++) {
u32 status = roothub_portstatus (ohci, i);
--


\
 
 \ /
  Last update: 2008-10-18 21:09    [W:0.113 / U:0.644 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site