lkml.org 
[lkml]   [2007]   [Jul]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    SubjectMarvell 7042 (sata_mv) fails to initialize drive
    I just tried hooking up a Hitachi 1TB SATA-II drive to a Marvell 7042 
    based controller, and the most recent Linux kernel (2.6.23-rc1) fails to
    properly initialize the interface. Here are the relevant kernel messages:

    > kernel: [43.312417] sata_mv 0000:06:00.0: version 0.81
    > kernel: [43.312752] ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16
    > kernel: [43.312757] ACPI: PCI Interrupt 0000:06:00.0[A] -> Link [APC5] -> GSI 16 (level, low) -> IRQ 16
    > kernel: [43.312788] sata_mv 0000:06:00.0: Applying 60X1C0 workarounds to unknown rev
    > kernel: [43.314443] sata_mv 0000:06:00.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx
    > kernel: [43.314535] scsi0 : sata_mv
    > kernel: [43.314581] scsi1 : sata_mv
    > kernel: [43.314614] scsi2 : sata_mv
    > kernel: [43.314640] scsi3 : sata_mv
    > kernel: [43.314660] ata1: SATA max UDMA/133 cmd 0x0000000000000000 ctl 0xffffc20003522120 bmdma 0x0000000000000000 irq 16
    > kernel: [43.314663] ata2: SATA max UDMA/133 cmd 0x0000000000000000 ctl 0xffffc20003524120 bmdma 0x0000000000000000 irq 16
    > kernel: [43.314666] ata3: SATA max UDMA/133 cmd 0x0000000000000000 ctl 0xffffc20003526120 bmdma 0x0000000000000000 irq 16
    > kernel: [43.314669] ata4: SATA max UDMA/133 cmd 0x0000000000000000 ctl 0xffffc20003528120 bmdma 0x0000000000000000 irq 16
    > kernel: [53.409086] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    > kernel: [59.741602] ata1: EH pending after completion, repeating EH (cnt=4)
    > kernel: [59.777642] ata2: SATA link down (SStatus 0 SControl 300)
    > kernel: [59.809752] ata3: SATA link down (SStatus 0 SControl 300)
    > kernel: [59.841740] ata4: SATA link down (SStatus 0 SControl 300)

    The kernel never even registers the drive as an available disk device,
    whereas everything appears to work fine, if I connect the disk to one of
    the other controllers (JMicron AHCI, or NVidia sata_nv) on this motherboard.

    As I have two of those disks (in a RAID-1 array) and multiple
    independent controllers, it is relatively easy for me to do some testing
    here. The worst case scenario is that I need to wait a couple of hours
    for the array to rebuild itself after I am done experimenting.

    Let me know, if there is anything I can do to help you diagnose the root
    cause, or whether this is a known bug and you don't need any help
    testing at this point.


    Markus
    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

    \
     
     \ /
      Last update: 2007-07-31 05:55    [W:0.023 / U:122.856 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site