lkml.org 
[lkml]   [2007]   [Jul]   [29]   [last100]   RSS Feed
Views: [more markup]  [less markup]  [headers]  [forward] 
 
Messages in this thread
/
DateSun, 29 Jul 2007 07:36:02 -0700
FromNick Pasich <>
SubjectRe: [linux-usb-devel] Edgeport UPS Monitoring Problems
Adam,

Yep..... That did it....
Thank You Very Much for your Super Quick Fix......
         ---( Nick )---

On Sun, Jul 29, 2007 at 10:04:44AM -0400, Adam Kropelin wrote:
> From: "Nick Pasich" <NewsLetters@NickAndBarb.net>
> >Here's the dmesg output ......
> >
> >[...]
> >Jul 29 05:20:07 NICK2 kernel: drivers/usb/serial/io_edgeport.c: LCR - 
> >write to send_cmd_write_uart_register register 0x03
> >Jul 29 05:20:07 NICK2 kernel: drivers/usb/serial/io_edgeport.c: 
> >SendCmdWriteUartReg - Not writing to MCR Register
> >Jul 29 05:20:07 NICK2 kernel: drivers/usb/serial/io_edgeport.c: MCR - 
> >write to send_cmd_write_uart_register register 0x0b
> >Jul 29 05:20:07 NICK2 kernel: drivers/usb/serial/io_edgeport.c: 
> >SendCmdWriteUartReg - Not writing to MCR Register
> >Jul 29 05:20:07 NICK2 kernel: drivers/usb/serial/io_edgeport.c: 
> >change_port_settings - baud rate = 9600
> >Jul 29 05:20:07 NICK2 kernel: drivers/usb/serial/io_edgeport.c: 
> >SendCmdWriteBaudRate - NOT Setting baud rate for port = 0, baud = 9600
> 
> Yup, there's what I expected. Not setting the baud rate and not writing 
> status registers is unlikely to produce working results. This 9600 must 
> be the default setting being applied.
> 
> >Jul 29 05:20:07 NICK2 kernel: drivers/usb/serial/io_edgeport.c: 
> >SendCmdWriteUartReg - Not writing to MCR Register
> >Jul 29 05:20:07 NICK2 kernel: drivers/usb/serial/io_edgeport.c: MCR - 
> >write to send_cmd_write_uart_register register 0x0b
> >Jul 29 05:20:07 NICK2 kernel: drivers/usb/serial/io_edgeport.c: 
> >SendCmdWriteUartReg - Not writing to MCR Register
> >Jul 29 05:20:07 NICK2 kernel: drivers/usb/serial/io_edgeport.c: 
> >change_port_settings - baud rate = 2400
> >Jul 29 05:20:07 NICK2 kernel: drivers/usb/serial/io_edgeport.c: 
> >SendCmdWriteBaudRate - NOT Setting baud rate for port = 0, baud = 2400
> 
> Here's apcupsd trying to set 2400 baud.
> 
> Please try the attached patch (against 2.6.22.1). This will allow 
> writing to the baud rate and MCR/LCR registers on non-EPIC adapters. I 
> suspect the previous code was a copy-paste error.
> 
> --Adam



-- 
--------
WebSite: http://NickAndBarb.net
--------
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2007-07-29 16:39    [from the cache]
©2003-2008