Messages in this thread | | | Date | Tue, 17 Jul 2007 14:29:21 -0400 | From | William Montgomery <> | Subject | Re: e100 PCI bridge problem |
| |
Krzysztof Halasa wrote:
>William Montgomery <william@opinicus.com> writes: > > > >>I am using a PCI analyzer and it shows the bus in an idle state after >>the lockup. The PCI transactions just prior to the lockup show a >>couple of interrupts from the card which appear to be handled >>correctly. Anything I should be looking for in particular? >> >> > >I'd try to check with other machine using "secondary" bus slot. >BTW: Are you able to analyze the "primary" bus transactions while >using the card in "secondary" bus? Perhaps there is something >wrong in front of the motherboard bridge? > > > I am able to analyze the primary bus while the using the card in the secondary and I see a very interesting thing on lockup - the primary side appears to be stuck on a read access to the memory mapped control regs of the LAN chip (82559) in what appears to be infinite target retries to the same address. Unfortunately I havent been able to capture what occurs just prior to this happening. This is quite different from what I capture on the secondary side; which is an idle bus
I have posted the lspci -vv listing below...
>A broken motherboard may be hard to diagnose, unfortunately. > >Can you post something like "lspci -vv" taken on both machines? > > Here is the lspci -vv on the machine with lockups (edited for brevity):
00:00.0 Host bridge: Intel Corp. 82845G/GL[Brookdale-G]/GE/PE DRAM Controller/Ho Subsystem: Intel Corp. 82845G/GL[Brookdale-G]/GE/PE DRAM Controller/Host Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Step Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- Latency: 0 Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M] Capabilities: [e4] #09 [1105] 00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB/EB/ER Hub interface to PCI Bridge (rev 82) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+ Latency: 0 Bus: primary=00, secondary=01, subordinate=03, sec-latency=32 I/O behind bridge: 00009000-0000afff Memory behind bridge: f4000000-f6ffffff Prefetchable memory behind bridge: 10000000-103fffff BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
01:0c.0 PCI bridge: Pericom Semiconductor: Unknown device 8150 (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Bus: primary=01, secondary=02, subordinate=03, sec-latency=32 I/O behind bridge: 00009000-00009fff Memory behind bridge: f4000000-f5ffffff Prefetchable memory behind bridge: 0000000010000000-0000000010300000 BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [b0] Slot ID: 0 slots, First-, chassis 00
02:06.0 PCI bridge: Hint Corp HB6 Universal PCI-PCI bridge (non-transparent mode) (rev 15) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Bus: primary=02, secondary=03, subordinate=03, sec-latency=32 I/O behind bridge: 00009000-00009fff Memory behind bridge: f4000000-f5ffffff Prefetchable memory behind bridge: 0000000010000000-0000000010300000 BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [90] #06 [0080] Capabilities: [a0] Vital Product Data03:04.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 08) Subsystem: Intel Corp. EtherExpress PRO/100+ Management Adapter with Alert On LAN* Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (2000ns min, 14000ns max), cache line size 08 Interrupt: pin A routed to IRQ 18 Region 0: Memory at f5403000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at 9000 [size=64] Region 2: Memory at f5000000 (32-bit, non-prefetchable) [size=1M] Expansion ROM at 10000000 [disabled] [size=1M] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=2 PME-
03:05.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 08) Subsystem: Intel Corp. EtherExpress PRO/100+ Management Adapter with Alert On LAN* Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (2000ns min, 14000ns max), cache line size 08 Interrupt: pin A routed to IRQ 19 Region 0: Memory at f5401000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at 9400 [size=64] Region 2: Memory at f5100000 (32-bit, non-prefetchable) [size=1M] Expansion ROM at 10100000 [disabled] [size=1M] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=2 PME-
03:06.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 08) Subsystem: Intel Corp. EtherExpress PRO/100+ Management Adapter with Alert On LAN* Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (2000ns min, 14000ns max), cache line size 08 Interrupt: pin A routed to IRQ 16 Region 0: Memory at f5400000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at 9800 [size=64] Region 2: Memory at f5200000 (32-bit, non-prefetchable) [size=1M] Expansion ROM at 10200000 [disabled] [size=1M] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=2 PME-
03:07.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 08) Subsystem: Intel Corp. EtherExpress PRO/100+ Management Adapter with Alert On LAN* Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (2000ns min, 14000ns max), cache line size 08 Interrupt: pin A routed to IRQ 17 Region 0: Memory at f5402000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at 9c00 [size=64] Region 2: Memory at f5300000 (32-bit, non-prefetchable) [size=1M] Expansion ROM at 10300000 [disabled] [size=1M] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=2 PME-
======================
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |