lkml.org 
[lkml]   [2007]   [Jun]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Subject[BUG] via c3/2.6.20 -- ps/2 keyboard doesn't work with console
    From
    Date
    Hi,

    I'm trying use the 2.6.20 kernel and have run into a problem using the
    ps/2 keyboard with console. When I type input in response to console
    output the characters aren't echo'ed and the console program doesn't
    receive the character input. It seems like the problem is specific to
    the ps/2 interface because a usb keyboard works fine.

    Here's dmesg output:



    Linux version 2.6.20 (root@albrecht.rdi1.com) (gcc version 3.3.3) #3 Wed
    Jun 6 09:58:30 EDT 2007
    BIOS-provided physical RAM map:
    sanitize start
    sanitize end
    copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end:
    000000000009fc00 type: 1
    copy_e820_map() type is E820_RAM
    copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end:
    00000000000a0000 type: 2
    copy_e820_map() start: 00000000000f0000 size: 0000000000010000 end:
    0000000000100000 type: 2
    copy_e820_map() start: 0000000000100000 size: 000000001f6f0000 end:
    000000001f7f0000 type: 1
    copy_e820_map() type is E820_RAM
    copy_e820_map() start: 000000001f7f0000 size: 0000000000003000 end:
    000000001f7f3000 type: 4
    copy_e820_map() start: 000000001f7f3000 size: 000000000000d000 end:
    000000001f800000 type: 3
    copy_e820_map() start: 00000000ffff0000 size: 0000000000010000 end:
    0000000100000000 type: 2
    BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000001f7f0000 (usable)
    BIOS-e820: 000000001f7f0000 - 000000001f7f3000 (ACPI NVS)
    BIOS-e820: 000000001f7f3000 - 000000001f800000 (ACPI data)
    BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
    503MB LOWMEM available.
    Entering add_active_range(0, 0, 129008) 0 entries of 256 used
    Zone PFN ranges:
    DMA 0 -> 4096
    Normal 4096 -> 129008
    early_node_map[1] active PFN ranges
    0: 0 -> 129008
    On node 0 totalpages: 129008
    DMA zone: 32 pages used for memmap
    DMA zone: 0 pages reserved
    DMA zone: 4064 pages, LIFO batch:0
    Normal zone: 975 pages used for memmap
    Normal zone: 123937 pages, LIFO batch:31
    DMI 2.3 present.
    ACPI: RSDP (v000 VIA605 ) @ 0x000f7510
    ACPI: RSDT (v001 VIA605 AWRDACPI 0x42302e31 AWRD 0x00000000) @
    0x1f7f3040
    ACPI: FADT (v001 VIA605 AWRDACPI 0x42302e31 AWRD 0x00000000) @
    0x1f7f30c0
    ACPI: DSDT (v001 VIA605 AWRDACPI 0x00001000 MSFT 0x0100000e) @
    0x00000000
    Allocating PCI resources starting at 20000000 (gap: 1f800000:e07f0000)
    Detected 800.024 MHz processor.
    Built 1 zonelists. Total pages: 128001
    Kernel command line: root=/dev/hda1 vga=791 splash=noconsole ide=nodma
    quiet noinitrd
    bootsplash: no console.
    ide_setup: ide=nodma : Prevented DMA
    No local APIC present or hardware disabled
    mapped APIC to ffffd000 (013f2000)
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Initializing CPU#0
    PID hash table entries: 2048 (order: 11, 8192 bytes)
    Console: colour dummy device 80x25
    Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
    Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
    Memory: 503740k/516032k available (4429k kernel code, 11704k reserved,
    1931k data, 224k init, 0k highmem)
    virtual kernel memory layout:
    fixmap : 0xfffb6000 - 0xfffff000 ( 292 kB)
    vmalloc : 0xe0000000 - 0xfffb4000 ( 511 MB)
    lowmem : 0xc0000000 - 0xdf7f0000 ( 503 MB)
    .init : 0xc073a000 - 0xc0772000 ( 224 kB)
    .data : 0xc0553428 - 0xc073638c (1931 kB)
    .text : 0xc0100000 - 0xc0553428 (4429 kB)
    Checking if this processor honours the WP bit even in supervisor mode...
    Ok.
    Calibrating delay using timer specific routine.. 1601.79 BogoMIPS
    (lpj=3203585)
    Mount-cache hash table entries: 512
    CPU: After generic identify, caps: 0381b03f 00000000 00000000 00000000
    00000000 00000000 00000000
    CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
    CPU: L2 Cache: 64K (32 bytes/line)
    CPU: After all inits, caps: 0381b13f 00000000 00000000 00000000 00000000
    000000dd 00000000
    Compat vDSO mapped to ffffe000.
    CPU: Centaur VIA Nehemiah stepping 08
    Checking 'hlt' instruction... OK.
    ACPI: Core revision 20060707
    ACPI: setting ELCR to 0080 (from 1c80)
    NET: Registered protocol family 16
    ACPI: bus type pci registered
    PCI: PCI BIOS revision 2.10 entry at 0xfb4d0, last bus=2
    PCI: Using configuration type 1
    Setting up standard PCI resources
    ACPI: Interpreter enabled
    ACPI: Using PIC for interrupt routing
    ACPI: PCI Root Bridge [PCI0] (0000:00)
    PCI: Probing PCI hardware (bus 00)
    ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
    PCI quirk: region 6000-607f claimed by vt82c686 HW-mon
    PCI quirk: region 5000-500f claimed by vt82c686 SMB
    Boot video device is 0000:01:00.0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *0,
    disabled.
    ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
    ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 11 *12 14 15)
    Linux Plug and Play Support v0.97 (c) Adam Belay
    pnp: PnP ACPI init
    pnp: PnP ACPI: found 11 devices
    SCSI subsystem initialized
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    PCI: Using ACPI for IRQ routing
    PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
    report
    PCI: Bridge: 0000:00:01.0
    IO window: disabled.
    MEM window: ec000000-ec0fffff
    PREFETCH window: e0000000-e7ffffff
    PCI: Bus 2, cardbus bridge: 0000:00:0d.0
    IO window: 00001000-000010ff
    IO window: 00001400-000014ff
    PREFETCH window: 20000000-23ffffff
    MEM window: 24000000-27ffffff
    PCI: Setting latency timer of device 0000:00:01.0 to 64
    ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
    PCI: setting IRQ 10 as level-triggered
    ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKA] -> GSI 10 (level,
    low) -> IRQ 10
    NET: Registered protocol family 2
    IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
    TCP established hash table entries: 16384 (order: 4, 65536 bytes)
    TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
    TCP: Hash tables configured (established 16384 bind 8192)
    TCP reno registered
    checking if image is initramfs...it isn't (bad gzip magic numbers);
    looks like an initrd
    Freeing initrd memory: 22k freed
    audit: initializing netlink socket (disabled)
    audit(1181215562.596:1): initialized
    squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
    Coda Kernel/Venus communications, v6.0.0, coda@cs.cmu.edu
    NTFS driver 2.1.28 [Flags: R/W].
    Supermount version 2.0.4 for kernel 2.6
    io scheduler noop registered
    io scheduler anticipatory registered
    io scheduler deadline registered
    io scheduler cfq registered (default)
    PCI: Disabling Via external APIC routing
    vesafb: framebuffer at 0xe0000000, mapped to 0xe0080000, using 6144k,
    total 7104k
    vesafb: mode is 1024x768x16, linelength=2048, pages=3
    vesafb: protected mode interface info at c000:79d0
    vesafb: pmi: set display start = c00c7a5a, set palette = c00c7aa3
    vesafb: scrolling: redraw
    vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
    bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size
    8984 bytes,<6>...found (1024x768, 14465 bytes, v3).
    Console: switching to colour frame buffer device 128x48
    fb0: VESA VGA frame buffer device
    input: Power Button (FF) as /class/input/input0
    ACPI: Power Button (FF) [PWRF]
    input: Power Button (CM) as /class/input/input1
    ACPI: Power Button (CM) [PWRB]
    ACPI: CPU0 (power states: C1[C1] C2[C2])
    ACPI: Processor [CPU0] (supports 2 throttling states)
    lp: driver loaded but no devices found
    Generic RTC Driver v1.07
    Non-volatile memory driver v1.2
    VIA RNG detected
    Linux agpgart interface v0.101 (c) Dave Jones
    agpgart: Detected VIA ProSavage PM133/PL133/PN133 chipset
    agpgart: AGP aperture is 64M @ 0xe8000000
    [drm] Initialized drm 1.1.0 20060810
    Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
    serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
    00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
    parport_pc: VIA 686A/8231 detected
    parport_pc: probing current configuration
    parport_pc: Current parallel port base: 0x0
    parport_pc: VIA parallel port disabled in BIOS
    FDC 0 is a post-1991 82077
    RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
    loop: loaded (max 8 devices)
    PPP generic driver version 2.4.2
    PPP Deflate Compression module registered
    PPP BSD Compression module registered
    NET: Registered protocol family 24
    8139too Fast Ethernet driver 0.9.28
    ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
    PCI: setting IRQ 11 as level-triggered
    ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKC] -> GSI 11 (level,
    low) -> IRQ 11
    eth0: RealTek RTL8139 at 0xc800, 00:e0:4c:69:2b:a5, IRQ 11
    eth0: Identified 8139 chip type 'RTL-8100B/8139D'
    tun: Universal TUN/TAP device driver, 1.6
    tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
    orinoco 0.15 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin
    <proski@gnu.org>, et al)
    orinoco_cs 0.15 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel
    Roskin <proski@gnu.org>, et al)
    Linux video capture interface: v2.00
    Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    ide: Assuming 33MHz system bus speed for PIO modes; override with
    idebus=xx
    VP_IDE: IDE controller at PCI slot 0000:00:07.1
    VP_IDE: chipset revision 6
    VP_IDE: not 100% native mode: will probe irqs later
    VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:07.1
    ide0: BM-DMA at 0xdd00-0xdd07, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xdd08-0xdd0f, BIOS settings: hdc:pio, hdd:pio
    Probing IDE interface ide0...
    hda: SanDisk SDCFB-1024, CFA DISK drive
    ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    Probing IDE interface ide1...
    Probing IDE interface ide1...
    Probing IDE interface ide2...
    Probing IDE interface ide3...
    hda: max request size: 128KiB
    hda: 2001888 sectors (1024 MB) w/1KiB Cache, CHS=1986/16/63
    hda: hda1 hda2
    Yenta: CardBus bridge found at 0000:00:0d.0 [3412:7856]
    Yenta: ISA IRQ mask 0x0000, PCI irq 10
    Socket status: 30000006
    usbmon: debugfs is not available
    ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
    (PCI)
    USB Universal Host Controller Interface driver v3.0
    ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 12
    PCI: setting IRQ 12 as level-triggered
    ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 12 (level,
    low) -> IRQ 12
    uhci_hcd 0000:00:07.2: UHCI Host Controller
    uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
    uhci_hcd 0000:00:07.2: irq 12, io base 0x0000e000
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:07.3[D] -> Link [LNKD] -> GSI 12 (level,
    low) -> IRQ 12
    uhci_hcd 0000:00:07.3: UHCI Host Controller
    uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
    uhci_hcd 0000:00:07.3: irq 12, io base 0x0000dc00
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    usb 2-1: new low speed USB device using uhci_hcd and address 2
    usb 2-1: configuration #1 chosen from 1 choice
    usbcore: registered new interface driver usblp
    drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
    Initializing USB Mass Storage driver...
    usbcore: registered new interface driver usb-storage
    USB Mass Storage support registered.
    usbcore: registered new interface driver hiddev
    input: Microsoft Basic Optical Mouse as /class/input/input2
    input: USB HID v1.10 Mouse [Microsoft Basic Optical Mouse] on
    usb-0000:00:07.3-1
    usbcore: registered new interface driver usbhid
    drivers/usb/input/hid-core.c: v2.6:USB HID core driver
    usbcore: registered new interface driver usblcd
    usbcore: registered new interface driver usbled
    usbcore: registered new interface driver uss720
    drivers/usb/misc/uss720.c: v0.6:USB Parport Cable driver for Cables
    using the Lucent Technologies USS720 Chip
    drivers/usb/misc/uss720.c: NOTE: this is a special purpose driver to
    allow nonstandard
    drivers/usb/misc/uss720.c: protocols (eg. bitbang) over USS720 usb to
    parallel cables
    drivers/usb/misc/uss720.c: If you just want to connect to a printer, use
    usblp instead
    PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
    PNP: PS/2 controller doesn't have AUX irq; using default 12
    serio: i8042 KBD port at 0x60,0x64 irq 1
    serio: i8042 AUX port at 0x60,0x64 irq 12
    mice: PS/2 mouse device common for all mice
    input: AT Translated Set 2 keyboard as /class/input/input3
    input: PC Speaker as /class/input/input4
    Linux telephony interface: v1.00
    ixj driver initialized.
    device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised:
    dm-devel@redhat.com
    Advanced Linux Sound Architecture Driver Version 1.0.14rc1 (Tue Jan 09
    09:56:17 2007 UTC).
    ACPI: PCI Interrupt 0000:00:07.5[C] -> Link [LNKC] -> GSI 11 (level,
    low) -> IRQ 11
    PCI: Setting latency timer of device 0000:00:07.5 to 64
    usbcore: registered new interface driver snd-usb-audio
    usbcore: registered new interface driver snd-usb-usx2y
    ALSA device list:
    #0: VIA 82C686A/B rev50 with VIA1612A at 0xc000, irq 11
    TCP cubic registered
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
    All bugs added by David S. Miller <davem@redhat.com>
    Using IPI Shortcut mode
    ACPI: (supports S0 S3 S4<6>Time: tsc clocksource has been installed.
    S5)
    ReiserFS: hda1: warning: read_super_block: found reiserfs format "3.6"
    with non-standard journal
    ReiserFS: hda1: using ordered data mode
    ReiserFS: hda1: journal params: device hda1, size 512, journal first
    block 18, max trans len 256, max batch 225, max commit age 30, max trans
    age 30
    ReiserFS: hda1: checking transaction log (hda1)
    Time: pit clocksource has been installed.
    ReiserFS: hda1: replayed 10 transactions in 1 seconds
    ReiserFS: hda1: Using r5 hash to sort names
    VFS: Mounted root (reiserfs filesystem) readonly.
    Freeing unused kernel memory: 224k freed
    ReiserFS: dm-0: warning: read_super_block: found reiserfs format "3.6"
    with non-standard journal
    ReiserFS: dm-0: using ordered data mode
    ReiserFS: dm-0: journal params: device dm-0, size 2048, journal first
    block 18, max trans len 1024, max batch 900, max commit age 30, max
    trans age 30
    ReiserFS: dm-0: checking transaction log (dm-0)
    ReiserFS: dm-0: replayed 20 transactions in 4 seconds
    ReiserFS: dm-0: Using r5 hash to sort names
    pcmcia: Detected deprecated PCMCIA ioctl usage from process: cardmgr.
    pcmcia: This interface will soon be removed from the kernel; please
    expect breakage unless you upgrade to new tools.
    pcmcia: see
    http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for
    details.
    eth0: link up, 10Mbps, half-duplex, lpa 0x0000



    Any idea what the problem is or how to debug?

    Paul Albrecht
    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

    \
     
     \ /
      Last update: 2007-06-07 21:15    [W:0.057 / U:0.884 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site