lkml.org 
[lkml]   [2007]   [May]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Subject[PATCH] Blackfin ethernet driver: on chip ethernet MAC controller driver
From
Date
From: "Wu, Bryan" <bryan.wu@analog.com>

This patch implements the driver necessary use the Analog Devices
Blackfin processor's on-chip ethernet MAC controller.

Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
---

drivers/net/Kconfig | 44 +
drivers/net/Makefile | 1
drivers/net/bfin_mac.c | 981 +++++++++++++++++++++++++++++++++++++++
drivers/net/bfin_mac.h | 147 +++++
4 files changed, 1173 insertions(+)

diff -puN drivers/net/Kconfig~blackfin-on-chip-ethernet-mac-controller-driver drivers/net/Kconfig
--- a/drivers/net/Kconfig~blackfin-on-chip-ethernet-mac-controller-driver
+++ a/drivers/net/Kconfig
@@ -836,6 +836,50 @@ config SMC91X
module, say M here and read <file:Documentation/kbuild/modules.txt>
as well as <file:Documentation/networking/net-modules.txt>.

+config BFIN_MAC
+ tristate "Blackfin 536/537 on-chip mac support"
+ depends on NET_ETHERNET && (BF537 || BF536) && (!BF537_PORT_H)
+ select CRC32
+ select BFIN_MAC_USE_L1 if DMA_UNCACHED_NONE
+ help
+ This is the driver for blackfin on-chip mac device. Say Y if you want it
+ compiled into the kernel. This driver is also available as a module
+ ( = code which can be inserted in and removed from the running kernel
+ whenever you want). The module will be called bfin_mac.
+
+config BFIN_MAC_USE_L1
+ bool "Use L1 memory for rx/tx packets"
+ depends on BFIN_MAC && BF537
+ default y
+ help
+ To get maximum network performace, you should use L1 memory as rx/tx buffers.
+ Say N here if you want to reserve L1 memory for other uses.
+
+config BFIN_TX_DESC_NUM
+ int "Number of transmit buffer packets"
+ depends on BFIN_MAC
+ range 6 10 if BFIN_MAC_USE_L1
+ range 10 100
+ default "10"
+ help
+ Set the number of buffer packets used in driver.
+
+config BFIN_RX_DESC_NUM
+ int "Number of receive buffer packets"
+ depends on BFIN_MAC
+ range 20 100 if BFIN_MAC_USE_L1
+ range 20 800
+ default "20"
+ help
+ Set the number of buffer packets used in driver.
+
+config BFIN_MAC_RMII
+ bool "RMII PHY Interface (EXPERIMENTAL)"
+ depends on BFIN_MAC && EXPERIMENTAL
+ default n
+ help
+ Use Reduced PHY MII Interface
+
config SMC9194
tristate "SMC 9194 support"
depends on NET_VENDOR_SMC && (ISA || MAC && BROKEN)
diff -puN drivers/net/Makefile~blackfin-on-chip-ethernet-mac-controller-driver drivers/net/Makefile
--- a/drivers/net/Makefile~blackfin-on-chip-ethernet-mac-controller-driver
+++ a/drivers/net/Makefile
@@ -194,6 +194,7 @@ obj-$(CONFIG_S2IO) += s2io.o
obj-$(CONFIG_MYRI10GE) += myri10ge/
obj-$(CONFIG_SMC91X) += smc91x.o
obj-$(CONFIG_SMC911X) += smc911x.o
+obj-$(CONFIG_BFIN_MAC) += bfin_mac.o
obj-$(CONFIG_DM9000) += dm9000.o
obj-$(CONFIG_FEC_8XX) += fec_8xx/
obj-$(CONFIG_PASEMI_MAC) += pasemi_mac.o
diff -puN /dev/null drivers/net/bfin_mac.c
--- /dev/null
+++ a/drivers/net/bfin_mac.c
@@ -0,0 +1,981 @@
+/*
+ * File: drivers/net/bfin_mac.c
+ * Based on:
+ * Author: Luke Yang <luke.yang@analog.com>
+ *
+ * Created:
+ * Description:
+ *
+ * Modified:
+ * Copyright 2004-2006 Analog Devices Inc.
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software ; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation ; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY ; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program ; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/timer.h>
+#include <linux/errno.h>
+#include <linux/ioport.h>
+#include <linux/crc32.h>
+#include <linux/device.h>
+#include <linux/spinlock.h>
+#include <linux/ethtool.h>
+#include <linux/mii.h>
+
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+
+#include <linux/platform_device.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/dma.h>
+#include <linux/dma-mapping.h>
+
+#include <asm/irq.h>
+#include <asm/blackfin.h>
+#include <asm/delay.h>
+
+#include "bfin_mac.h"
+
+#define CARDNAME "bfin_mac"
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Luke Yang");
+MODULE_DESCRIPTION("Blackfin MAC Driver");
+
+#if defined(CONFIG_BFIN_MAC_USE_L1)
+# define bfin_mac_alloc(dma_handle, size) l1_data_sram_zalloc(size)
+# define bfin_mac_free(dma_handle, ptr) l1_data_sram_free(ptr)
+#else
+# define bfin_mac_alloc(dma_handle, size) dma_alloc_coherent(NULL, size, dma_handle, GFP_DMA)
+# define bfin_mac_free(dma_handle, ptr) dma_free_coherent(NULL, sizeof(*ptr), ptr, dma_handle)
+#endif
+
+#define PKT_BUF_SZ 1580
+
+static void desc_list_free(void);
+
+/* pointers to maintain transmit list */
+static struct net_dma_desc_tx *tx_list_head;
+static struct net_dma_desc_tx *tx_list_tail;
+static struct net_dma_desc_rx *rx_list_head;
+static struct net_dma_desc_rx *rx_list_tail;
+static struct net_dma_desc_rx *current_rx_ptr;
+static struct net_dma_desc_tx *current_tx_ptr;
+static struct net_dma_desc_tx *tx_desc;
+static struct net_dma_desc_rx *rx_desc;
+
+static int desc_list_init(void)
+{
+ struct net_dma_desc_tx *tmp_desc_tx;
+ struct net_dma_desc_rx *tmp_desc_rx;
+ int i;
+ struct sk_buff *new_skb;
+#if !defined(CONFIG_BFIN_MAC_USE_L1)
+ dma_addr_t dma_handle;
+#endif
+
+ tx_desc =
+ bfin_mac_alloc(&dma_handle,
+ sizeof(struct net_dma_desc_tx) *
+ CONFIG_BFIN_TX_DESC_NUM);
+ if (tx_desc == NULL)
+ goto init_error;
+
+ rx_desc =
+ bfin_mac_alloc(&dma_handle,
+ sizeof(struct net_dma_desc_rx) *
+ CONFIG_BFIN_RX_DESC_NUM);
+ if (rx_desc == NULL)
+ goto init_error;
+
+ /* init tx_list */
+ for (i = 0; i < CONFIG_BFIN_TX_DESC_NUM; i++) {
+
+ tmp_desc_tx = tx_desc + i;
+
+ if (i == 0) {
+ tx_list_head = tmp_desc_tx;
+ tx_list_tail = tmp_desc_tx;
+ }
+
+ tmp_desc_tx->desc_a.start_addr =
+ (unsigned long)tmp_desc_tx->packet;
+ tmp_desc_tx->desc_a.x_count = 0;
+ tmp_desc_tx->desc_a.config.b_DMA_EN = 0; /* disabled */
+ tmp_desc_tx->desc_a.config.b_WNR = 0; /* read from memory */
+ tmp_desc_tx->desc_a.config.b_WDSIZE = 2; /* wordsize is 32 bits */
+ tmp_desc_tx->desc_a.config.b_NDSIZE = 6; /* 6 half words is desc size. */
+ tmp_desc_tx->desc_a.config.b_FLOW = 7; /* large desc flow */
+ tmp_desc_tx->desc_a.next_dma_desc = &(tmp_desc_tx->desc_b);
+
+ tmp_desc_tx->desc_b.start_addr =
+ (unsigned long)(&(tmp_desc_tx->status));
+ tmp_desc_tx->desc_b.x_count = 0;
+ tmp_desc_tx->desc_b.config.b_DMA_EN = 1; /* enabled */
+ tmp_desc_tx->desc_b.config.b_WNR = 1; /* write to memory */
+ tmp_desc_tx->desc_b.config.b_WDSIZE = 2; /* wordsize is 32 bits */
+ tmp_desc_tx->desc_b.config.b_DI_EN = 0; /* disable interrupt */
+ tmp_desc_tx->desc_b.config.b_NDSIZE = 6;
+ tmp_desc_tx->desc_b.config.b_FLOW = 7; /* stop mode */
+ tmp_desc_tx->skb = NULL;
+ tx_list_tail->desc_b.next_dma_desc = &(tmp_desc_tx->desc_a);
+ tx_list_tail->next = tmp_desc_tx;
+
+ tx_list_tail = tmp_desc_tx;
+ }
+ tx_list_tail->next = tx_list_head; /* tx_list is a circle */
+ tx_list_tail->desc_b.next_dma_desc = &(tx_list_head->desc_a);
+ current_tx_ptr = tx_list_head;
+
+ /* init rx_list */
+ for (i = 0; i < CONFIG_BFIN_RX_DESC_NUM; i++) {
+
+ tmp_desc_rx = rx_desc + i;
+
+ if (i == 0) {
+ rx_list_head = tmp_desc_rx;
+ rx_list_tail = tmp_desc_rx;
+ }
+
+ /* allocat a new skb for next time receive */
+ new_skb = dev_alloc_skb(PKT_BUF_SZ + 2);
+ if (!new_skb) {
+ printk(KERN_NOTICE CARDNAME
+ ": init: low on mem - packet dropped\n");
+ goto init_error;
+ }
+ skb_reserve(new_skb, 2);
+ tmp_desc_rx->skb = new_skb;
+ /* since RXDWA is enabled */
+ tmp_desc_rx->desc_a.start_addr =
+ (unsigned long)new_skb->data - 2;
+ tmp_desc_rx->desc_a.x_count = 0;
+ tmp_desc_rx->desc_a.config.b_DMA_EN = 1; /* enabled */
+ tmp_desc_rx->desc_a.config.b_WNR = 1; /* Write to memory */
+ tmp_desc_rx->desc_a.config.b_WDSIZE = 2; /* wordsize is 32 bits */
+ tmp_desc_rx->desc_a.config.b_NDSIZE = 6; /* 6 half words is desc size. */
+ tmp_desc_rx->desc_a.config.b_FLOW = 7; /* large desc flow */
+ tmp_desc_rx->desc_a.next_dma_desc = &(tmp_desc_rx->desc_b);
+
+ tmp_desc_rx->desc_b.start_addr =
+ (unsigned long)(&(tmp_desc_rx->status));
+ tmp_desc_rx->desc_b.x_count = 0;
+ tmp_desc_rx->desc_b.config.b_DMA_EN = 1; /* enabled */
+ tmp_desc_rx->desc_b.config.b_WNR = 1; /* Write to memory */
+ tmp_desc_rx->desc_b.config.b_WDSIZE = 2; /* wordsize is 32 bits */
+ tmp_desc_rx->desc_b.config.b_NDSIZE = 6;
+ tmp_desc_rx->desc_b.config.b_DI_EN = 1; /* enable interrupt */
+ tmp_desc_rx->desc_b.config.b_FLOW = 7; /* large mode */
+ rx_list_tail->desc_b.next_dma_desc = &(tmp_desc_rx->desc_a);
+
+ rx_list_tail->next = tmp_desc_rx;
+ rx_list_tail = tmp_desc_rx;
+ }
+ rx_list_tail->next = rx_list_head; /* rx_list is a circle */
+ rx_list_tail->desc_b.next_dma_desc = &(rx_list_head->desc_a);
+ current_rx_ptr = rx_list_head;
+
+ return 0;
+
+ init_error:
+ desc_list_free();
+ printk(KERN_ERR CARDNAME ": kmalloc failed\n");
+ return -ENOMEM;
+}
+
+static void desc_list_free(void)
+{
+ struct net_dma_desc_rx *tmp_desc_rx;
+ struct net_dma_desc_tx *tmp_desc_tx;
+ int i;
+#if !defined(CONFIG_BFIN_MAC_USE_L1)
+ dma_addr_t dma_handle = 0;
+#endif
+
+ if (tx_desc != NULL) {
+ tmp_desc_tx = tx_list_head;
+ for (i = 0; i < CONFIG_BFIN_TX_DESC_NUM; i++) {
+ if (tmp_desc_tx != NULL) {
+ if (tmp_desc_tx->skb) {
+ dev_kfree_skb(tmp_desc_tx->skb);
+ tmp_desc_tx->skb = NULL;
+ }
+
+ }
+ tmp_desc_tx = tmp_desc_tx->next;
+ }
+ bfin_mac_free(dma_handle, tx_desc);
+ }
+
+ if (rx_desc != NULL) {
+ tmp_desc_rx = rx_list_head;
+ for (i = 0; i < CONFIG_BFIN_RX_DESC_NUM; i++) {
+ if (tmp_desc_rx != NULL) {
+ if (tmp_desc_rx->skb) {
+ dev_kfree_skb(tmp_desc_rx->skb);
+ tmp_desc_rx->skb = NULL;
+ }
+ }
+ tmp_desc_rx = tmp_desc_rx->next;
+ }
+ bfin_mac_free(dma_handle, rx_desc);
+ }
+}
+
+/*---PHY CONTROL AND CONFIGURATION-----------------------------------------*/
+
+/* Set FER regs to MUX in Ethernet pins */
+static void setup_pin_mux(void)
+{
+ unsigned int fer_val;
+
+ /*
+ * FER reg bug work-around
+ * read it once
+ */
+ fer_val = bfin_read_PORTH_FER();
+
+#if defined(CONFIG_BFIN_MAC_RMII)
+ fer_val = 0xC373;
+#else
+ fer_val = 0xffff;
+#endif
+ /* write it twice to the same value */
+
+ bfin_write_PORTH_FER(fer_val);
+ bfin_write_PORTH_FER(fer_val);
+}
+
+/* Wait until the previous MDC/MDIO transaction has completed */
+static void poll_mdc_done(void)
+{
+ /* poll the STABUSY bit */
+ while ((bfin_read_EMAC_STAADD()) & STABUSY) {
+ };
+}
+
+/* Read an off-chip register in a PHY through the MDC/MDIO port */
+static u16 read_phy_reg(u16 PHYAddr, u16 RegAddr)
+{
+ poll_mdc_done();
+ bfin_write_EMAC_STAADD(SET_PHYAD(PHYAddr) | SET_REGAD(RegAddr) | STABUSY); /* read mode */
+ poll_mdc_done();
+
+ return (u16) bfin_read_EMAC_STADAT();
+}
+
+/* Write an off-chip register in a PHY through the MDC/MDIO port */
+static void raw_write_phy_reg(u16 PHYAddr, u16 RegAddr, u32 Data)
+{
+ bfin_write_EMAC_STADAT(Data);
+
+ bfin_write_EMAC_STAADD(SET_PHYAD(PHYAddr) | SET_REGAD(RegAddr) | STAOP | STABUSY); /* write mode */
+
+ poll_mdc_done();
+}
+
+static void write_phy_reg(u16 PHYAddr, u16 RegAddr, u32 Data)
+{
+ poll_mdc_done();
+ raw_write_phy_reg(PHYAddr, RegAddr, Data);
+}
+
+/* set up the phy */
+static void bf537mac_setphy(struct net_device *dev)
+{
+ u16 phydat;
+ u32 sysctl;
+ struct bf537mac_local *lp = netdev_priv(dev);
+
+ pr_debug("start settting up phy\n");
+
+ /* Program PHY registers */
+ phydat = 0;
+
+ /* issue a reset */
+ raw_write_phy_reg(lp->PhyAddr, PHYREG_MODECTL, 0x8000);
+
+ /* wait half a second */
+ udelay(500);
+
+ phydat = read_phy_reg(lp->PhyAddr, PHYREG_MODECTL);
+
+ /* advertise flow control supported */
+ phydat = read_phy_reg(lp->PhyAddr, PHYREG_ANAR);
+ phydat |= (1 << 10);
+ write_phy_reg(lp->PhyAddr, PHYREG_ANAR, phydat);
+
+ phydat = 0;
+ if (lp->Negotiate) {
+ phydat |= 0x1000; /* enable auto negotiation */
+ } else {
+ if (lp->FullDuplex) {
+ phydat |= (1 << 8); /* full duplex */
+ } else {
+ phydat &= (~(1 << 8)); /* half duplex */
+ }
+ if (!lp->Port10) {
+ phydat |= (1 << 13); /* 100 Mbps */
+ } else {
+ phydat &= (~(1 << 13)); /* 10 Mbps */
+ }
+ }
+
+ if (lp->Loopback) {
+ phydat |= (1 << 14); /* enable TX->RX loopback */
+#if 0
+ write_phy_reg(lp->PhyAddr, PHYREG_MODECTL, phydat);
+#endif
+ }
+
+ write_phy_reg(lp->PhyAddr, PHYREG_MODECTL, phydat);
+ udelay(500);
+
+ phydat = read_phy_reg(lp->PhyAddr, PHYREG_MODECTL);
+ /* check for SMSC PHY */
+ if ((read_phy_reg(lp->PhyAddr, PHYREG_PHYID1) == 0x7)
+ && ((read_phy_reg(lp->PhyAddr, PHYREG_PHYID2) & 0xfff0) == 0xC0A0)) {
+ /* we have SMSC PHY so reqest interrupt on link down condition */
+ write_phy_reg(lp->PhyAddr, 30, 0x0ff); /* enable interrupts */
+ /* enable PHY_INT */
+ sysctl = bfin_read_EMAC_SYSCTL();
+ sysctl |= 0x1;
+#if 0
+ bfin_write_EMAC_SYSCTL(sysctl);
+#endif
+ }
+}
+
+/**************************************************************************/
+void setup_system_regs(struct net_device *dev)
+{
+ int PHYADDR;
+ unsigned short sysctl, phydat;
+ u32 opmode;
+ struct bf537mac_local *lp = netdev_priv(dev);
+ int count = 0;
+
+ PHYADDR = lp->PhyAddr;
+
+ /* Enable PHY output */
+ if (!(bfin_read_VR_CTL() & PHYCLKOE))
+ bfin_write_VR_CTL(bfin_read_VR_CTL() | PHYCLKOE);
+
+ /* MDC = 2.5 MHz */
+ sysctl = SET_MDCDIV(24);
+ /* Odd word alignment for Receive Frame DMA word */
+ /* Configure checksum support and rcve frame word alignment */
+#if defined(BFIN_MAC_CSUM_OFFLOAD)
+ sysctl |= RXDWA | RXCKS;
+#else
+ sysctl |= RXDWA;
+#endif
+ bfin_write_EMAC_SYSCTL(sysctl);
+ /* auto negotiation on */
+ /* full duplex */
+ /* 100 Mbps */
+ phydat = PHY_ANEG_EN | PHY_DUPLEX | PHY_SPD_SET;
+ write_phy_reg(PHYADDR, PHYREG_MODECTL, phydat);
+
+ /* test if full duplex supported */
+ do {
+ msleep(100);
+ phydat = read_phy_reg(PHYADDR, PHYREG_MODESTAT);
+ if (count > 30) {
+ printk(KERN_NOTICE CARDNAME
+ ": Link is down, please check your network connection\n");
+ break;
+ }
+ count++;
+ } while (!(phydat & 0x0004));
+
+ phydat = read_phy_reg(PHYADDR, PHYREG_ANLPAR);
+
+ if ((phydat & 0x0100) || (phydat & 0x0040)) {
+ opmode = FDMODE;
+ } else {
+ opmode = 0;
+ printk(KERN_INFO CARDNAME ": Network is set to half duplex\n");
+ }
+
+#if defined(CONFIG_BFIN_MAC_RMII)
+ opmode |= RMII; /* For Now only 100MBit are supported */
+#endif
+
+ bfin_write_EMAC_OPMODE(opmode);
+
+#if 0
+ bfin_write_EMAC_MMC_CTL(RSTC | CROLL | MMCE);
+#endif
+ bfin_write_EMAC_MMC_CTL(RSTC | CROLL);
+
+ /* Initialize the TX DMA channel registers */
+ bfin_write_DMA2_X_COUNT(0);
+ bfin_write_DMA2_X_MODIFY(4);
+ bfin_write_DMA2_Y_COUNT(0);
+ bfin_write_DMA2_Y_MODIFY(0);
+
+ /* Initialize the RX DMA channel registers */
+ bfin_write_DMA1_X_COUNT(0);
+ bfin_write_DMA1_X_MODIFY(4);
+ bfin_write_DMA1_Y_COUNT(0);
+ bfin_write_DMA1_Y_MODIFY(0);
+}
+
+void setup_mac_addr(u8 * mac_addr)
+{
+ /* this depends on a little-endian machine */
+ bfin_write_EMAC_ADDRLO(*(u32 *) & mac_addr[0]);
+ bfin_write_EMAC_ADDRHI(*(u16 *) & mac_addr[4]);
+}
+
+static void adjust_tx_list(void)
+{
+ if (tx_list_head->status.status_word != 0
+ && current_tx_ptr != tx_list_head) {
+ goto adjust_head; /* released something, just return; */
+ }
+
+ /* if nothing released, check wait condition */
+ /* current's next can not be the head, otherwise the dma will not stop as we want */
+ if (current_tx_ptr->next->next == tx_list_head) {
+ while (tx_list_head->status.status_word == 0) {
+ udelay(10);
+ if (tx_list_head->status.status_word != 0
+ || !(bfin_read_DMA2_IRQ_STATUS() & 0x08)) {
+ goto adjust_head;
+ }
+ }
+ if (tx_list_head->status.status_word != 0) {
+ goto adjust_head;
+ }
+ }
+
+ return;
+
+ adjust_head:
+ do {
+ tx_list_head->desc_a.config.b_DMA_EN = 0;
+ tx_list_head->status.status_word = 0;
+ if (tx_list_head->skb) {
+ dev_kfree_skb(tx_list_head->skb);
+ tx_list_head->skb = NULL;
+ } else {
+ printk(KERN_ERR CARDNAME
+ ": no sk_buff in a transmitted frame!\n");
+ }
+ tx_list_head = tx_list_head->next;
+ } while (tx_list_head->status.status_word != 0
+ && current_tx_ptr != tx_list_head);
+ return;
+
+}
+
+static int bf537mac_hard_start_xmit(struct sk_buff *skb, struct net_device *dev)
+{
+ struct bf537mac_local *lp = netdev_priv(dev);
+ unsigned int data;
+
+ current_tx_ptr->skb = skb;
+ /* Is skb->data always 16-bit aligned? Do we need to memcpy((char *)(tail->packet + 2),skb->data,len)? */
+ if ((((unsigned int)(skb->data)) & 0x02) == 2) {
+ /* move skb->data to current_tx_ptr payload */
+ data = (unsigned int)(skb->data) - 2;
+ *((unsigned short *)data) = (unsigned short)(skb->len);
+ current_tx_ptr->desc_a.start_addr = (unsigned long)data;
+ blackfin_dcache_flush_range(data, (data + (skb->len)) + 2); /* this is important! */
+
+ } else {
+ *((unsigned short *)(current_tx_ptr->packet)) =
+ (unsigned short)(skb->len);
+ memcpy((char *)(current_tx_ptr->packet + 2), skb->data,
+ (skb->len));
+ current_tx_ptr->desc_a.start_addr =
+ (unsigned long)current_tx_ptr->packet;
+ if (current_tx_ptr->status.status_word != 0)
+ current_tx_ptr->status.status_word = 0;
+ blackfin_dcache_flush_range((unsigned int)current_tx_ptr->
+ packet,
+ (unsigned int)(current_tx_ptr->
+ packet + skb->len) +
+ 2);
+ }
+
+ current_tx_ptr->desc_a.config.b_DMA_EN = 1; /* enable this packet's dma */
+
+ if (bfin_read_DMA2_IRQ_STATUS() & 0x08) { /* tx dma is running, just return */
+ goto out;
+ } else {
+ /* tx dma is not running */
+ bfin_write_DMA2_NEXT_DESC_PTR(&(current_tx_ptr->desc_a));
+ /* dma enabled, read from memory, size is 6 */
+ bfin_write_DMA2_CONFIG(*((unsigned short *)(&(current_tx_ptr->desc_a.config))));
+ /* Turn on the EMAC tx */
+ bfin_write_EMAC_OPMODE(bfin_read_EMAC_OPMODE() | TE);
+ }
+
+ out:
+ adjust_tx_list();
+ current_tx_ptr = current_tx_ptr->next;
+ dev->trans_start = jiffies;
+ lp->stats.tx_packets++;
+ lp->stats.tx_bytes += (skb->len);
+ return 0;
+}
+
+static void bf537mac_rx(struct net_device *dev)
+{
+ struct sk_buff *skb, *new_skb;
+ struct bf537mac_local *lp = netdev_priv(dev);
+ unsigned short len;
+
+ /* allocat a new skb for next time receive */
+ skb = current_rx_ptr->skb;
+ new_skb = dev_alloc_skb(PKT_BUF_SZ + 2);
+ if (!new_skb) {
+ printk(KERN_NOTICE CARDNAME
+ ": rx: low on mem - packet dropped\n");
+ lp->stats.rx_dropped++;
+ goto out;
+ }
+ /* reserve 2 bytes for RXDWA padding */
+ skb_reserve(new_skb, 2);
+ current_rx_ptr->skb = new_skb;
+ current_rx_ptr->desc_a.start_addr = (unsigned long)new_skb->data - 2;
+
+#if 0
+ int i;
+ if (len >= 64) {
+ for (i=0;i<len;i++) {
+ printk("%.2x-",((unsigned char *)pkt)[i]);
+ if (((i%8)==0) && (i!=0)) printk("\n");
+ }
+ printk("\n");
+ }
+#endif
+
+ len = (unsigned short)((current_rx_ptr->status.status_word) & RX_FRLEN);
+ skb_put(skb, len);
+ blackfin_dcache_invalidate_range((unsigned long)skb->head,
+ (unsigned long)skb->tail);
+
+ dev->last_rx = jiffies;
+ skb->dev = dev;
+ skb->protocol = eth_type_trans(skb, dev);
+#if defined(BFIN_MAC_CSUM_OFFLOAD)
+ skb->csum = current_rx_ptr->status.ip_payload_csum;
+ skb->ip_summed = CHECKSUM_PARTIAL;
+#endif
+
+ netif_rx(skb);
+ lp->stats.rx_packets++;
+ lp->stats.rx_bytes += len;
+ current_rx_ptr->status.status_word = 0x00000000;
+ current_rx_ptr = current_rx_ptr->next;
+
+ out:
+ return;
+}
+
+/* interrupt routine to handle rx and error signal */
+static irqreturn_t bf537mac_interrupt(int irq, void *dev_id)
+{
+ struct net_device *dev = dev_id;
+ int number = 0;
+
+ get_one_packet:
+ if (current_rx_ptr->status.status_word == 0) { /* no more new packet received */
+ if (number == 0) {
+ if (current_rx_ptr->next->status.status_word != 0) {
+ current_rx_ptr = current_rx_ptr->next;
+ goto real_rx;
+ }
+ }
+ bfin_write_DMA1_IRQ_STATUS(bfin_read_DMA1_IRQ_STATUS() |
+ DMA_DONE | DMA_ERR);
+ return IRQ_HANDLED;
+ }
+
+ real_rx:
+ bf537mac_rx(dev);
+ number++;
+ goto get_one_packet;
+}
+
+#ifdef CONFIG_NET_POLL_CONTROLLER
+static void bf537mac_poll(struct net_device *dev)
+{
+ disable_irq(IRQ_MAC_RX);
+ bf537mac_interrupt(IRQ_MAC_RX, dev);
+ enable_irq(IRQ_MAC_RX);
+}
+#endif /* CONFIG_NET_POLL_CONTROLLER */
+
+static void bf537mac_reset(void)
+{
+ unsigned int opmode;
+
+ opmode = bfin_read_EMAC_OPMODE();
+ opmode &= (~RE);
+ opmode &= (~TE);
+ /* Turn off the EMAC */
+ bfin_write_EMAC_OPMODE(bfin_read_EMAC_OPMODE() & opmode);
+}
+
+/*
+ * Enable Interrupts, Receive, and Transmit
+ */
+static int bf537mac_enable(struct net_device *dev)
+{
+ u32 opmode;
+
+ pr_debug("%s: %s\n", dev->name, __FUNCTION__);
+
+ /* Set RX DMA */
+ bfin_write_DMA1_NEXT_DESC_PTR(&(rx_list_head->desc_a));
+ bfin_write_DMA1_CONFIG(*
+ ((unsigned short
+ *)(&(rx_list_head->desc_a.config))));
+
+ /* Wait MII done */
+ poll_mdc_done();
+
+ /* We enable only RX here */
+ /* ASTP : Enable Automatic Pad Stripping
+ PR : Promiscuous Mode for test
+ PSF : Receive frames with total length less than 64 bytes.
+ FDMODE : Full Duplex Mode
+ LB : Internal Loopback for test
+ RE : Receiver Enable */
+ opmode = bfin_read_EMAC_OPMODE();
+ if (opmode & FDMODE)
+ opmode |= PSF;
+ else
+ opmode |= DRO | DC | PSF;
+ opmode |= RE;
+
+#if defined(CONFIG_BFIN_MAC_RMII)
+ opmode |= RMII; /* For Now only 100MBit are supported */
+#ifdef CONFIG_BF_REV_0_2
+ opmode |= TE;
+#endif
+#endif
+ /* Turn on the EMAC rx */
+ bfin_write_EMAC_OPMODE(opmode);
+
+ return 0;
+}
+
+/* Our watchdog timed out. Called by the networking layer */
+static void bf537mac_timeout(struct net_device *dev)
+{
+ pr_debug("%s: %s\n", dev->name, __FUNCTION__);
+
+ bf537mac_reset();
+
+ /* reset tx queue */
+ tx_list_tail = tx_list_head->next;
+
+ bf537mac_enable(dev);
+
+ /* We can accept TX packets again */
+ dev->trans_start = jiffies;
+ netif_wake_queue(dev);
+}
+
+/*
+ * Get the current statistics.
+ * This may be called with the card open or closed.
+ */
+static struct net_device_stats *bf537mac_query_statistics(struct net_device
+ *dev)
+{
+ struct bf537mac_local *lp = netdev_priv(dev);
+
+ pr_debug("%s: %s\n", dev->name, __FUNCTION__);
+
+ return &lp->stats;
+}
+
+/*
+ * This routine will, depending on the values passed to it,
+ * either make it accept multicast packets, go into
+ * promiscuous mode (for TCPDUMP and cousins) or accept
+ * a select set of multicast packets
+ */
+static void bf537mac_set_multicast_list(struct net_device *dev)
+{
+ u32 sysctl;
+
+ if (dev->flags & IFF_PROMISC) {
+ printk(KERN_INFO "%s: set to promisc mode\n", dev->name);
+ sysctl = bfin_read_EMAC_OPMODE();
+ sysctl |= RAF;
+ bfin_write_EMAC_OPMODE(sysctl);
+ } else if (dev->flags & IFF_ALLMULTI || dev->mc_count > 16) {
+ /* accept all multicast */
+ sysctl = bfin_read_EMAC_OPMODE();
+ sysctl |= PAM;
+ bfin_write_EMAC_OPMODE(sysctl);
+ } else if (dev->mc_count) {
+ /* set multicast */
+ } else {
+ /* clear promisc or multicast mode */
+ sysctl = bfin_read_EMAC_OPMODE();
+ sysctl &= ~(RAF | PAM);
+ bfin_write_EMAC_OPMODE(sysctl);
+ }
+}
+
+/*
+ * this puts the device in an inactive state
+ */
+static void bf537mac_shutdown(struct net_device *dev)
+{
+ /* Turn off the EMAC */
+ bfin_write_EMAC_OPMODE(0x00000000);
+ /* Turn off the EMAC RX DMA */
+ bfin_write_DMA1_CONFIG(0x0000);
+ bfin_write_DMA2_CONFIG(0x0000);
+}
+
+/*
+ * Open and Initialize the interface
+ *
+ * Set up everything, reset the card, etc..
+ */
+static int bf537mac_open(struct net_device *dev)
+{
+ pr_debug("%s: %s\n", dev->name, __FUNCTION__);
+
+ /*
+ * Check that the address is valid. If its not, refuse
+ * to bring the device up. The user must specify an
+ * address using ifconfig eth0 hw ether xx:xx:xx:xx:xx:xx
+ */
+ if (!is_valid_ether_addr(dev->dev_addr)) {
+ printk(KERN_WARNING CARDNAME ": no valid ethernet hw addr\n");
+ return -EINVAL;
+ }
+
+ /* initial rx and tx list */
+ desc_list_init();
+
+ bf537mac_setphy(dev);
+ setup_system_regs(dev);
+ bf537mac_reset();
+ bf537mac_enable(dev);
+
+ pr_debug("hardware init finished\n");
+ netif_start_queue(dev);
+ netif_carrier_on(dev);
+
+ return 0;
+}
+
+/*
+ *
+ * this makes the board clean up everything that it can
+ * and not talk to the outside world. Caused by
+ * an 'ifconfig ethX down'
+ */
+static int bf537mac_close(struct net_device *dev)
+{
+ pr_debug("%s: %s\n", dev->name, __FUNCTION__);
+
+ netif_stop_queue(dev);
+ netif_carrier_off(dev);
+
+ /* clear everything */
+ bf537mac_shutdown(dev);
+
+ /* free the rx/tx buffers */
+ desc_list_free();
+
+ return 0;
+}
+
+static int __init bf537mac_probe(struct net_device *dev)
+{
+ struct bf537mac_local *lp = netdev_priv(dev);
+ int retval;
+
+ /* Grab the MAC address in the MAC */
+ *(u32 *) (&(dev->dev_addr[0])) = bfin_read_EMAC_ADDRLO();
+ *(u16 *) (&(dev->dev_addr[4])) = (u16) bfin_read_EMAC_ADDRHI();
+
+/* probe mac */
+ /*todo: how to proble? which is revision_register */
+ bfin_write_EMAC_ADDRLO(0x12345678);
+ if (bfin_read_EMAC_ADDRLO() != 0x12345678) {
+ pr_debug("can't detect bf537 mac!\n");
+ retval = -ENODEV;
+ goto err_out;
+ }
+
+ /*Is it valid? (Did bootloader initialize it?) */
+ if (!is_valid_ether_addr(dev->dev_addr)) {
+ /* Grab the MAC from the board somehow - this is done in the
+ arch/blackfin/boards/bf537/boardname.c */
+ get_bf537_ether_addr(dev->dev_addr);
+ }
+
+ /* If still not valid, get a random one */
+ if (!is_valid_ether_addr(dev->dev_addr)) {
+ random_ether_addr(dev->dev_addr);
+ }
+
+ setup_mac_addr(dev->dev_addr);
+
+ /* Fill in the fields of the device structure with ethernet values. */
+ ether_setup(dev);
+
+ dev->open = bf537mac_open;
+ dev->stop = bf537mac_close;
+ dev->hard_start_xmit = bf537mac_hard_start_xmit;
+ dev->tx_timeout = bf537mac_timeout;
+ dev->get_stats = bf537mac_query_statistics;
+ dev->set_multicast_list = bf537mac_set_multicast_list;
+#if 0
+ dev->ethtool_ops = &bf537mac_ethtool_ops;
+#endif
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ dev->poll_controller = bf537mac_poll;
+#endif
+
+ /* fill in some of the fields */
+ lp->version = 1;
+ lp->PhyAddr = 0x01;
+ lp->CLKIN = 25;
+ lp->FullDuplex = 0;
+ lp->Negotiate = 1;
+ lp->FlowControl = 0;
+ spin_lock_init(&lp->lock);
+
+ /* set the GPIO pins to Ethernet mode */
+ setup_pin_mux();
+
+ /* now, enable interrupts */
+ /* register irq handler */
+ if (request_irq
+ (IRQ_MAC_RX, bf537mac_interrupt, IRQF_DISABLED | IRQF_SHARED,
+ "BFIN537_MAC_RX", dev)) {
+ printk(KERN_WARNING CARDNAME
+ ": Unable to attach BlackFin MAC RX interrupt\n");
+ return -EBUSY;
+ }
+
+ /* Enable PHY output early */
+ if (!(bfin_read_VR_CTL() & PHYCLKOE))
+ bfin_write_VR_CTL(bfin_read_VR_CTL() | PHYCLKOE);
+
+ retval = register_netdev(dev);
+ if (retval == 0) {
+ /* now, print out the card info, in a short format.. */
+ printk(KERN_INFO "Blackfin mac net device registered\n");
+ }
+
+ err_out:
+ return retval;
+}
+
+static int bfin_mac_probe(struct platform_device *pdev)
+{
+ struct net_device *ndev;
+
+ ndev = alloc_etherdev(sizeof(struct bf537mac_local));
+
+ if (!ndev) {
+ printk(KERN_WARNING CARDNAME ": could not allocate device\n");
+ return -ENOMEM;
+ }
+
+ if (bf537mac_probe(ndev) != 0) {
+ platform_set_drvdata(pdev, NULL);
+ free_netdev(ndev);
+ printk(KERN_WARNING CARDNAME ": not found\n");
+ return -ENODEV;
+ }
+
+ SET_MODULE_OWNER(ndev);
+ SET_NETDEV_DEV(ndev, &pdev->dev);
+
+ platform_set_drvdata(pdev, ndev);
+
+ return 0;
+}
+
+static int bfin_mac_remove(struct platform_device *pdev)
+{
+ struct net_device *ndev = platform_get_drvdata(pdev);
+
+ platform_set_drvdata(pdev, NULL);
+
+ unregister_netdev(ndev);
+
+ free_irq(IRQ_MAC_RX, ndev);
+
+ free_netdev(ndev);
+
+ return 0;
+}
+
+static int bfin_mac_suspend(struct platform_device *pdev, pm_message_t state)
+{
+ return 0;
+}
+
+static int bfin_mac_resume(struct platform_device *pdev)
+{
+ return 0;
+}
+
+static struct platform_driver bfin_mac_driver = {
+ .probe = bfin_mac_probe,
+ .remove = bfin_mac_remove,
+ .resume = bfin_mac_resume,
+ .suspend = bfin_mac_suspend,
+ .driver = {
+ .name = CARDNAME,
+ },
+};
+
+static int __init bfin_mac_init(void)
+{
+ return platform_driver_register(&bfin_mac_driver);
+}
+
+module_init(bfin_mac_init);
+
+static void __exit bfin_mac_cleanup(void)
+{
+ platform_driver_unregister(&bfin_mac_driver);
+}
+
+module_exit(bfin_mac_cleanup);
diff -puN /dev/null drivers/net/bfin_mac.h
--- /dev/null
+++ a/drivers/net/bfin_mac.h
@@ -0,0 +1,147 @@
+/*
+ * File: drivers/net/bfin_mac.h
+ * Based on:
+ * Author: Luke Yang <luke.yang@analog.com>
+ *
+ * Created:
+ * Description:
+ *
+ * Modified:
+ * Copyright 2004-2006 Analog Devices Inc.
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software ; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation ; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY ; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program ; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+/*
+ * PHY REGISTER NAMES
+ */
+#define PHYREG_MODECTL 0x0000
+#define PHYREG_MODESTAT 0x0001
+#define PHYREG_PHYID1 0x0002
+#define PHYREG_PHYID2 0x0003
+#define PHYREG_ANAR 0x0004
+#define PHYREG_ANLPAR 0x0005
+#define PHYREG_ANER 0x0006
+#define PHYREG_NSR 0x0010
+#define PHYREG_LBREMR 0x0011
+#define PHYREG_REC 0x0012
+#define PHYREG_10CFG 0x0013
+#define PHYREG_PHY1_1 0x0014
+#define PHYREG_PHY1_2 0x0015
+#define PHYREG_PHY2 0x0016
+#define PHYREG_TW_1 0x0017
+#define PHYREG_TW_2 0x0018
+#define PHYREG_TEST 0x0019
+
+#define PHY_RESET 0x8000
+#define PHY_ANEG_EN 0x1000
+#define PHY_DUPLEX 0x0100
+#define PHY_SPD_SET 0x2000
+
+#define BFIN_MAC_CSUM_OFFLOAD
+
+typedef struct _DMA_CONFIG {
+ unsigned short b_DMA_EN:1; /* Bit 0 : DMA Enable */
+ unsigned short b_WNR:1; /* Bit 1 : DMA Direction */
+ unsigned short b_WDSIZE:2; /* Bit 2 & 3 : DMA Tranfer Word size */
+ unsigned short b_DMA2D:1; /* Bit 4 : DMA Mode 2D or 1D */
+ unsigned short b_RESTART:1; /* Bit 5 : Retain the FIFO */
+ unsigned short b_DI_SEL:1; /* Bit 6 : Data Interrupt Timing Select */
+ unsigned short b_DI_EN:1; /* Bit 7 : Data Interrupt Enable */
+ unsigned short b_NDSIZE:4; /* Bit 8 to 11 : Flex descriptor Size */
+ unsigned short b_FLOW:3; /* Bit 12 to 14 : FLOW */
+} DMA_CONFIG_REG;
+
+struct dma_descriptor {
+ struct dma_descriptor *next_dma_desc;
+ unsigned long start_addr;
+ DMA_CONFIG_REG config;
+ unsigned short x_count;
+};
+
+#if 0
+struct status_area {
+ unsigned short ip_hdr_chksum; /* the IP header checksum */
+ unsigned short ip_payload_chksum; /* the IP header and payload checksum */
+ unsigned long status_word; /* the frame status word */
+};
+#endif
+
+struct status_area_rx {
+#if defined(BFIN_MAC_CSUM_OFFLOAD)
+ unsigned short ip_hdr_csum; /* ip header checksum */
+ unsigned short ip_payload_csum; /* ip payload(udp or tcp or others) checksum */
+#endif
+ unsigned long status_word; /* the frame status word */
+};
+
+struct status_area_tx {
+ unsigned long status_word; /* the frame status word */
+};
+
+/* use two descriptors for a packet */
+struct net_dma_desc_rx {
+ struct net_dma_desc_rx *next;
+ struct sk_buff *skb;
+ struct dma_descriptor desc_a;
+ struct dma_descriptor desc_b;
+ volatile struct status_area_rx status;
+};
+
+/* use two descriptors for a packet */
+struct net_dma_desc_tx {
+ struct net_dma_desc_tx *next;
+ struct sk_buff *skb;
+ struct dma_descriptor desc_a;
+ struct dma_descriptor desc_b;
+ volatile unsigned char packet[1560];
+ volatile struct status_area_tx status;
+};
+
+struct bf537mac_local {
+ /*
+ * these are things that the kernel wants me to keep, so users
+ * can find out semi-useless statistics of how well the card is
+ * performing
+ */
+ struct net_device_stats stats;
+
+ int version;
+
+ int FlowEnabled; /* record if data flow is active */
+ int EtherIntIVG; /* IVG for the ethernet interrupt */
+ int RXIVG; /* IVG for the RX completion */
+ int TXIVG; /* IVG for the TX completion */
+ int PhyAddr; /* PHY address */
+ int OpMode; /* set these bits n the OPMODE regs */
+ int Port10; /* set port speed to 10 Mbit/s */
+ int GenChksums; /* IP checksums to be calculated */
+ int NoRcveLnth; /* dont insert recv length at start of buffer */
+ int StripPads; /* remove trailing pad bytes */
+ int FullDuplex; /* set full duplex mode */
+ int Negotiate; /* enable auto negotiation */
+ int Loopback; /* loopback at the PHY */
+ int Cache; /* Buffers may be cached */
+ int FlowControl; /* flow control active */
+ int CLKIN; /* clock in value in MHZ */
+ unsigned short IntMask; /* interrupt mask */
+ unsigned char Mac[6]; /* MAC address of the board */
+ spinlock_t lock;
+};
+
+extern void get_bf537_ether_addr(char *addr);
_
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
\
 
 \ /
  Last update: 2007-05-23 11:31    [W:0.065 / U:0.796 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site