lkml.org 
[lkml]   [2007]   [Apr]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH][RFC][POWERPC] i2c: adds support for i2c bus on 8xx
From
On Fri, Apr 20, 2007 at 08:27:14AM +0400, Vitaly Bordug wrote:

> diff --git a/arch/powerpc/platforms/8xx/mpc885ads_setup.c b/arch/powerpc/platforms/8xx/mpc885ads_setup.c
> index 9bd81c7..d32e066 100644
> --- a/arch/powerpc/platforms/8xx/mpc885ads_setup.c
> +++ b/arch/powerpc/platforms/8xx/mpc885ads_setup.c
> @@ -51,6 +51,7 @@ static void init_smc1_uart_ioports(struc
> static void init_smc2_uart_ioports(struct fs_uart_platform_info* fpi);
> static void init_scc3_ioports(struct fs_platform_info* ptr);
> static void init_irda_ioports(void);
> +static void init_i2c_ioports(void);
>
> void __init mpc885ads_board_setup(void)
> {
> @@ -120,6 +121,10 @@ #endif
> #ifdef CONFIG_8XX_SIR
> init_irda_ioports();
> #endif
> +
> +#ifdef CONFIG_I2C_RPXLITE
> + init_i2c_ioports();
> +#endif

Does it hurt to always do it, even when the driver is not enabled? THat'd
do away with an ifdef.

Also, if you move the static function up, you don't need a prototype. That
goes for other stuff in this file too.

> }
>
>
> @@ -361,6 +366,15 @@ static void init_irda_ioports()
> immr_unmap(cp);
> }
>
> +static void init_i2c_ioports()
> +{
> + cpm8xx_t *cp = (cpm8xx_t *)immr_map(im_cpm);
> +
> + setbits32(&cp->cp_pbpar, 0x00000030);
> + setbits32(&cp->cp_pbdir, 0x00000030);
> + setbits16(&cp->cp_pbodr, 0x0030);
> +}

Looks like you moved this out of the driver and into the platform
code. What happens to other platforms where it's used?

> +
> int platform_device_skip(const char *model, int id)
> {
> #ifdef CONFIG_MPC8xx_SECOND_ETH_SCC3
> diff --git a/arch/powerpc/sysdev/fsl_soc.c b/arch/powerpc/sysdev/fsl_soc.c
> index 419b688..7ecd537 100644
> --- a/arch/powerpc/sysdev/fsl_soc.c
> +++ b/arch/powerpc/sysdev/fsl_soc.c
> @@ -331,7 +331,7 @@ static int __init fsl_i2c_of_init(void)
> for (np = NULL, i = 0;
> (np = of_find_compatible_node(np, "i2c", "fsl-i2c")) != NULL;
> i++) {
> - struct resource r[2];
> + struct resource r[3];

Why? No code that uses it has been changed. Is it a bugfix?

> struct fsl_i2c_platform_data i2c_data;
> const unsigned char *flags = NULL;
>
> @@ -1215,4 +1215,63 @@ err:
>
> arch_initcall(fs_irda_of_init);
>
> +static const char *i2c_regs = "regs";
> +static const char *i2c_pram = "pram";
> +static const char *i2c_irq = "interrupt";
> +
> +static int __init fsl_i2c_cpm_of_init(void)
> +{
> + struct device_node *np;
> + unsigned int i;
> + struct platform_device *i2c_dev;
> + int ret;
> +
> + for (np = NULL, i = 0;
> + (np = of_find_compatible_node(np, "i2c", "fsl-i2c-cpm")) != NULL;
> + i++) {
> + struct resource r[3];
> + struct fsl_i2c_platform_data i2c_data;
> +
> + memset(&r, 0, sizeof(r));
> + memset(&i2c_data, 0, sizeof(i2c_data));
> +
> + ret = of_address_to_resource(np, 0, &r[0]);
> + if (ret)
> + goto err;
> + r[0].name = i2c_regs;
> +
> + ret = of_address_to_resource(np, 1, &r[1]);
> + if (ret)
> + goto err;
> + r[1].name = i2c_pram;
> +
> + r[2].start = r[2].end = irq_of_parse_and_map(np, 0);
> + r[2].flags = IORESOURCE_IRQ;
> + r[2].name = i2c_irq;
> +
> + i2c_dev = platform_device_register_simple("fsl-i2c-cpm", i, &r[0], 3);
> + if (IS_ERR(i2c_dev)) {
> + ret = PTR_ERR(i2c_dev);
> + goto err;
> + }
> +
> + ret =
> + platform_device_add_data(i2c_dev, &i2c_data,
> + sizeof(struct
> + fsl_i2c_platform_data));
> + if (ret)
> + goto unreg;
> + }
> +
> + return 0;
> +
> +unreg:
> + platform_device_unregister(i2c_dev);
> +err:
> + return ret;
> +}
> +
> +arch_initcall(fsl_i2c_cpm_of_init);

This could all be done with an of_platform driver instead, and avoid the above.
(Someone else already suggested that I believe).

> #endif /* CONFIG_8xx */
> diff --git a/drivers/i2c/algos/Kconfig b/drivers/i2c/algos/Kconfig
> index 5889907..7d7fb87 100644
> --- a/drivers/i2c/algos/Kconfig
> +++ b/drivers/i2c/algos/Kconfig
> @@ -37,6 +37,8 @@ config I2C_ALGOPCA
> config I2C_ALGO8XX
> tristate "MPC8xx CPM I2C interface"
> depends on 8xx
> + help
> + 8xx I2C Algorithm
>
> config I2C_ALGO_SGI
> tristate "I2C SGI interfaces"
> diff --git a/drivers/i2c/algos/Makefile b/drivers/i2c/algos/Makefile
> index cac1051..1bd3b37 100644
> --- a/drivers/i2c/algos/Makefile
> +++ b/drivers/i2c/algos/Makefile
> @@ -6,6 +6,7 @@ obj-$(CONFIG_I2C_ALGOBIT) += i2c-algo-bi
> obj-$(CONFIG_I2C_ALGOPCF) += i2c-algo-pcf.o
> obj-$(CONFIG_I2C_ALGOPCA) += i2c-algo-pca.o
> obj-$(CONFIG_I2C_ALGO_SGI) += i2c-algo-sgi.o
> +obj-$(CONFIG_I2C_ALGO8XX) += i2c-algo-8xx.o
>
> ifeq ($(CONFIG_I2C_DEBUG_ALGO),y)
> EXTRA_CFLAGS += -DDEBUG
> diff --git a/drivers/i2c/algos/i2c-algo-8xx.c b/drivers/i2c/algos/i2c-algo-8xx.c
> new file mode 100644
> index 0000000..b1f414a
> --- /dev/null
> +++ b/drivers/i2c/algos/i2c-algo-8xx.c
> @@ -0,0 +1,622 @@
> +/*
> + * i2c-algo-8xx.c i2x driver algorithms for MPC8XX CPM
> + * Copyright (c) 1999 Dan Malek (dmalek@jlc.net).
> + *
> + This program is free software; you can redistribute it and/or modify
> + it under the terms of the GNU General Public License as published by
> + the Free Software Foundation; either version 2 of the License, or
> + (at your option) any later version.
> +
> + This program is distributed in the hope that it will be useful,
> + but WITHOUT ANY WARRANTY; without even the implied warranty of
> + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + GNU General Public License for more details.
> +
> + You should have received a copy of the GNU General Public License
> + along with this program; if not, write to the Free Software
> + Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
> + *
> + * moved into proper i2c interface; separated out platform specific
> + * parts into i2c-rpx.c
> + * Brad Parker (brad@heeltoe.com)
> + */
> +
> +
> +/* $Id: i2c-algo-8xx.c,v 1.15 2004/11/20 08:02:24 khali Exp $ */
> +
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/delay.h>
> +#include <linux/slab.h>
> +#include <linux/init.h>
> +#include <linux/interrupt.h>
> +#include <linux/errno.h>
> +#include <linux/sched.h>
> +#include <linux/i2c.h>
> +#include <linux/i2c-algo-8xx.h>
> +#include <asm/io.h>
> +#include <asm/cacheflush.h>
> +#include <asm/time.h>
> +#include <asm/mpc8xx.h>
> +
> +#define CPM_MAX_READ 513
> +#undef I2C_CHIP_ERRATA /* Try ot define this if you have an older CPU(earlier than rev D4) */
> +
> +static wait_queue_head_t iic_wait;
> +static ushort r_tbase, r_rbase;
> +
> +int cpm_debug = 0;
> +int cpm_scan = 0;
> +
> +static irqreturn_t cpm_iic_interrupt(int irq, void *dev_id)
> +{
> + i2c8xx_t *i2c = (i2c8xx_t *) dev_id;
> + if (cpm_debug > 1)
> + printk("cpm_iic_interrupt(dev_id=%p)\n", dev_id);
> +#if 0
> + /* Chip errata, clear enable. This is not needed on rev D4 CPUs */
> + /* This should probably be removed and replaced by I2C_CHIP_ERRATA stuff */
> + /* Someone with a buggy CPU needs to confirm that */
> + out_8(&i2c->i2c_i2mod, in_8(&i2c->i2c_i2mod) | ~1);
> +#endif
> + /* Clear interrupt.
> + */
> + out_8(&i2c->i2c_i2cer, 0xff);
> +
> + /* Get 'me going again.
> + */
> + wake_up_interruptible(&iic_wait);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static void cpm_iic_init(struct i2c_algo_8xx_data *cpm)
> +{
> + iic_t *iip = cpm->iip;
> + i2c8xx_t *i2c = cpm->i2c;
> + unsigned char brg;
> +
> + if (cpm_debug)
> + printk(KERN_DEBUG "cpm_iic_init()\n");
> +
> + /* Initialize the parameter ram.
> + * We need to make sure many things are initialized to zero,
> + * especially in the case of a microcode patch.
> + */
> + iip->iic_rstate = 0;
> + iip->iic_rdp = 0;
> + iip->iic_rbptr = 0;
> + iip->iic_rbc = 0;
> + iip->iic_rxtmp = 0;
> + iip->iic_tstate = 0;
> + iip->iic_tdp = 0;
> + iip->iic_tbptr = 0;
> + iip->iic_tbc = 0;
> + iip->iic_txtmp = 0;
> +
> + /* Set up the IIC parameters in the parameter ram.
> + */
> + iip->iic_tbase = r_tbase = cpm->dp_addr;
> + iip->iic_rbase = r_rbase = cpm->dp_addr + sizeof(cbd_t) * 2;
> +
> + if (cpm_debug) {
> + printk("iip %p, dp_addr 0x%x\n", cpm->iip, cpm->dp_addr);
> + printk("iic_tbase %d, r_tbase %d\n", iip->iic_tbase, r_tbase);
> + }
> +
> + iip->iic_tfcr = SMC_EB;
> + iip->iic_rfcr = SMC_EB;
> +
> + /* Set maximum receive size.
> + */
> + iip->iic_mrblr = CPM_MAX_READ;
> +
> + /* Initialize Tx/Rx parameters.
> + */
> + if (cpm->reloc == 0) {
> + cpm8xx_t *cp = cpm->cp;
> + u16 v = mk_cr_cmd(CPM_CR_CH_I2C, CPM_CR_INIT_TRX) | CPM_CR_FLG;
> +
> + out_be16(&cp->cp_cpcr, v);
> + while (in_be16(&cp->cp_cpcr) & CPM_CR_FLG) ;
> + } else {
> + iip->iic_rbptr = iip->iic_rbase;
> + iip->iic_tbptr = iip->iic_tbase;
> + iip->iic_rstate = 0;
> + iip->iic_tstate = 0;
> + }
> +
> + /* Select an arbitrary address. Just make sure it is unique.
> + */
> + out_8(&i2c->i2c_i2add, 0xfe);
> +
> + /* Make clock run at 60 KHz.
> + */
> + brg = (unsigned char)(ppc_proc_freq / (32 * 2 * 60000) - 3);
> + out_8(&i2c->i2c_i2brg, brg);
> +
> + out_8(&i2c->i2c_i2mod, 0x00);
> + out_8(&i2c->i2c_i2com, 0x01); /* Master mode */
> +
> + /* Disable interrupts.
> + */
> + out_8(&i2c->i2c_i2cmr, 0);
> + out_8(&i2c->i2c_i2cer, 0xff);
> +
> + init_waitqueue_head(&iic_wait);
> +
> + /* Install interrupt handler.
> + */
> + if (cpm_debug) {
> + printk("%s[%d] Install ISR for IRQ %d\n",
> + __func__, __LINE__, CPMVEC_I2C);
> + }
> + request_irq(cpm->irq, cpm_iic_interrupt, 0, "8xx_i2c", i2c);
> +}
> +
> +static int cpm_iic_shutdown(struct i2c_algo_8xx_data *cpm)
> +{
> + i2c8xx_t *i2c = cpm->i2c;
> +
> + /* Shut down IIC.
> + */
> + out_8(&i2c->i2c_i2mod, in_8(&i2c->i2c_i2mod) | ~1);
> + out_8(&i2c->i2c_i2cmr, 0);
> + out_8(&i2c->i2c_i2cer, 0xff);
> +
> + return (0);
> +}
> +
> +static void cpm_reset_iic_params(iic_t * iip)
> +{
> + iip->iic_tbase = r_tbase;
> + iip->iic_rbase = r_rbase;
> +
> + iip->iic_tfcr = SMC_EB;
> + iip->iic_rfcr = SMC_EB;
> +
> + iip->iic_mrblr = CPM_MAX_READ;
> +
> + iip->iic_rstate = 0;
> + iip->iic_rdp = 0;
> + iip->iic_rbptr = iip->iic_rbase;
> + iip->iic_rbc = 0;
> + iip->iic_rxtmp = 0;
> + iip->iic_tstate = 0;
> + iip->iic_tdp = 0;
> + iip->iic_tbptr = iip->iic_tbase;
> + iip->iic_tbc = 0;
> + iip->iic_txtmp = 0;
> +}
> +
> +#define BD_SC_NAK ((ushort)0x0004) /* NAK - did not respond */
> +#define BD_SC_OV ((ushort)0x0002) /* OV - receive overrun */
> +#define CPM_CR_CLOSE_RXBD ((ushort)0x0007)
> +
> +static void force_close(struct i2c_algo_8xx_data *cpm)
> +{
> + i2c8xx_t *i2c = cpm->i2c;
> + if (cpm->reloc == 0) { /* micro code disabled */
> + cpm8xx_t *cp = cpm->cp;
> + u16 v = mk_cr_cmd(CPM_CR_CH_I2C, CPM_CR_CLOSE_RXBD) | CPM_CR_FLG;
> +
> + if (cpm_debug)
> + printk("force_close()\n");
> +
> + out_be16(&cp->cp_cpcr, v);
> + while (in_be16(&cp->cp_cpcr) & CPM_CR_FLG) ;
> + }
> + out_8(&i2c->i2c_i2cmr, 0x00); /* Disable all interrupts */
> + out_8(&i2c->i2c_i2cer, 0xff);
> +}
> +
> +/* Read from IIC...
> + * abyte = address byte, with r/w flag already set
> + */
> +static int
> +cpm_iic_read(struct i2c_algo_8xx_data *cpm, u_char abyte, char *buf, int count)
> +{
> + iic_t *iip = cpm->iip;
> + i2c8xx_t *i2c = cpm->i2c;
> + cbd_t *tbdf, *rbdf;
> + u_char *tb;
> + unsigned long tmo;
> + int res = 0;
> +
> + if (count >= CPM_MAX_READ)
> + return -EINVAL;
> +
> + /* check for and use a microcode relocation patch */
> + if (cpm->reloc) {
> + cpm_reset_iic_params(iip);
> + }
> +
> + tbdf = (cbd_t *) cpm_dpram_addr(iip->iic_tbase);
> + rbdf = (cbd_t *) cpm_dpram_addr(iip->iic_rbase);
> +
> + /* To read, we need an empty buffer of the proper length.
> + * All that is used is the first byte for address, the remainder
> + * is just used for timing (and doesn't really have to exist).
> + */
> + tb = cpm->temp;
> + tb = (u_char *) (((uint) tb + 15) & ~15);
> + tb[0] = abyte; /* Device address byte w/rw flag */
> +
> + flush_dcache_range((unsigned long)tb, (unsigned long)(tb + 1));
> +
> + if (cpm_debug)
> + printk("cpm_iic_read(abyte=0x%x)\n", abyte);
> +
> + tbdf->cbd_bufaddr = __pa(tb);
> + tbdf->cbd_datlen = count + 1;
> + tbdf->cbd_sc = BD_SC_READY | BD_SC_LAST | BD_SC_WRAP | BD_IIC_START;
> +
> + iip->iic_mrblr = count + 1; /* prevent excessive read, +1
> + is needed otherwise will the
> + RXB interrupt come too early */
> +
> + /* flush will invalidate too. */
> + flush_dcache_range((unsigned long)buf, (unsigned long)(buf + count));
> +
> + rbdf->cbd_datlen = 0;
> + rbdf->cbd_bufaddr = __pa(buf);
> + rbdf->cbd_sc = BD_SC_EMPTY | BD_SC_WRAP | BD_SC_INTRPT;
> +
> + if (count > 16) {
> + /* Chip bug, set enable here */
> + out_8(&i2c->i2c_i2cmr, 0x13); /* Enable some interupts */
> + out_8(&i2c->i2c_i2cer, 0xff);
> + out_8(&i2c->i2c_i2mod, in_8(&i2c->i2c_i2mod) | 1); /* Enable */
> + out_8(&i2c->i2c_i2com, in_8(&i2c->i2c_i2com) | 0x80); /* Begin transmission */
> +
> + /* Wait for IIC transfer */
> + res = wait_event_interruptible_timeout(iic_wait, 0, 1 * HZ);
> + } else { /* busy wait for small transfers, its faster */
> + out_8(&i2c->i2c_i2cmr, 0x00); /* Disable I2C interupts */
> + out_8(&i2c->i2c_i2cer, 0xff);
> + out_8(&i2c->i2c_i2mod, in_8(&i2c->i2c_i2mod) | 1); /* Enable */
> + out_8(&i2c->i2c_i2com, in_8(&i2c->i2c_i2com) | 0x80); /* Begin transmission */
> +
> + tmo = jiffies + 1 * HZ;
> + while (!(in_8(&i2c->i2c_i2cer) & 0x11 || time_after(jiffies, tmo))) ;/* Busy wait, with a timeout */
> + }
> +
> + if ( res < 0) {
> + force_close(cpm);
> + if (cpm_debug)
> + printk("IIC read: timeout!\n");
> + return -EIO;
> + }
> +#ifdef I2C_CHIP_ERRATA
> + /* Chip errata, clear enable. This is not needed on rev D4 CPUs.
> + Disabling I2C too early may cause too short stop condition */
> + udelay(4);
> + out_8(&i2c->i2c_i2mod, in_8(&i2c->i2c_i2mod) | ~1);
> +#endif
> + if (cpm_debug) {
> + printk("tx sc %04x, rx sc %04x\n", tbdf->cbd_sc, rbdf->cbd_sc);
> + }
> +
> + if (tbdf->cbd_sc & BD_SC_READY) {
> + printk("IIC read; complete but tbuf ready\n");
> + force_close(cpm);
> + printk("tx sc %04x, rx sc %04x\n", tbdf->cbd_sc, rbdf->cbd_sc);
> + }
> +
> + if (tbdf->cbd_sc & BD_SC_NAK) {
> + if (cpm_debug)
> + printk("IIC read; no ack\n");
> + return -EREMOTEIO;
> + }
> +
> + if (rbdf->cbd_sc & BD_SC_EMPTY) {
> + /* force_close(cpm); */
> + if (cpm_debug) {
> + printk("IIC read; complete but rbuf empty\n");
> + printk("tx sc %04x, rx sc %04x\n",
> + tbdf->cbd_sc, rbdf->cbd_sc);
> + }
> + return -EREMOTEIO;
> + }
> +
> + if (rbdf->cbd_sc & BD_SC_OV) {
> + if (cpm_debug)
> + printk("IIC read; Overrun\n");
> + return -EREMOTEIO;;
> + }
> +
> + if (cpm_debug)
> + printk("read %d bytes\n", rbdf->cbd_datlen);
> +
> + if (rbdf->cbd_datlen < count) {
> + if (cpm_debug)
> + printk("IIC read; short, wanted %d got %d\n",
> + count, rbdf->cbd_datlen);
> + return 0;
> + }
> +
> + return count;
> +}
> +
> +/* Write to IIC...
> + * addr = address byte, with r/w flag already set
> + */
> +static int
> +cpm_iic_write(struct i2c_algo_8xx_data *cpm, u_char abyte, char *buf, int count)
> +{
> + iic_t *iip = cpm->iip;
> + i2c8xx_t *i2c = cpm->i2c;
> + cbd_t *tbdf;
> + u_char *tb;
> + unsigned long tmo;
> + int res = 0;
> +
> + /* check for and use a microcode relocation patch */
> + if (cpm->reloc) {
> + cpm_reset_iic_params(iip);
> + }
> + tb = cpm->temp;
> + tb = (u_char *) (((uint) tb + 15) & ~15);
> + *tb = abyte; /* Device address byte w/rw flag */
> +
> + flush_dcache_range((unsigned long)tb, (unsigned long)(tb + 1));
> + flush_dcache_range((unsigned long)buf, (unsigned long)(buf + count));
> +
> + if (cpm_debug)
> + printk("cpm_iic_write(abyte=0x%x)\n", abyte);
> +
> + /* set up 2 descriptors */
> +
> +
> + tbdf = (cbd_t *) cpm_dpram_addr(iip->iic_tbase);
> +
> + tbdf[0].cbd_bufaddr = __pa(tb);
> + tbdf[0].cbd_datlen = 1;
> + tbdf[0].cbd_sc = BD_SC_READY | BD_IIC_START;
> +
> + tbdf[1].cbd_bufaddr = __pa(buf);
> + tbdf[1].cbd_datlen = count;
> + tbdf[1].cbd_sc = BD_SC_READY | BD_SC_INTRPT | BD_SC_LAST | BD_SC_WRAP;
> +
> + if (count > 16) {
> + /* Chip bug, set enable here */
> + out_8(&i2c->i2c_i2cmr, 0x13); /* Enable some interupts */
> + out_8(&i2c->i2c_i2cer, 0xff);
> + out_8(&i2c->i2c_i2mod, in_8(&i2c->i2c_i2mod) | 1); /* Enable */
> + out_8(&i2c->i2c_i2com, in_8(&i2c->i2c_i2com) | 0x80); /* Begin transmission */
> +
> + /* Wait for IIC transfer */
> + res = wait_event_interruptible_timeout(iic_wait, 0, 1 * HZ);
> + } else { /* busy wait for small transfers, its faster */
> + out_8(&i2c->i2c_i2cmr, 0x00); /* Disable I2C interupts */
> + out_8(&i2c->i2c_i2cer, 0xff);
> + out_8(&i2c->i2c_i2mod, in_8(&i2c->i2c_i2mod) | 1); /* Enable */
> + out_8(&i2c->i2c_i2com, in_8(&i2c->i2c_i2com) | 0x80); /* Begin transmission */
> + tmo = jiffies + 1 * HZ;
> + while (!(in_8(&i2c->i2c_i2cer) & 0x12 || time_after(jiffies, tmo))) ;/* Busy wait, with a timeout */
> + }
> +
> + if ( res < 0) {
> + force_close(cpm);
> + if (cpm_debug)
> + printk("IIC write: timeout!\n");
> + return -EIO;
> + }
> +#ifdef I2C_CHIP_ERRATA
> + /* Chip errata, clear enable. This is not needed on rev D4 CPUs.
> + Disabling I2C too early may cause too short stop condition */
> + udelay(4);
> + out_8(&i2c->i2c_i2mod, in_8(&i2c->i2c_i2mod) | ~1);
> +#endif
> + if (cpm_debug) {
> + printk("tx0 sc %04x, tx1 sc %04x\n",
> + tbdf[0].cbd_sc, tbdf[1].cbd_sc);
> + }
> +
> + if (tbdf->cbd_sc & BD_SC_NAK) {
> + if (cpm_debug)
> + printk("IIC write; no ack\n");
> + return 0;
> + }
> +
> + if (tbdf->cbd_sc & BD_SC_READY) {
> + if (cpm_debug)
> + printk("IIC write; complete but tbuf ready\n");
> + return 0;
> + }
> +
> + return count;
> +}
> +
> +/* See if an IIC address exists..
> + * addr = 7 bit address, unshifted
> + */
> +static int cpm_iic_tryaddress(struct i2c_algo_8xx_data *cpm, int addr)
> +{
> + iic_t *iip = cpm->iip;
> + i2c8xx_t *i2c = cpm->i2c;
> + cbd_t *tbdf, *rbdf;
> + u_char *tb;
> + unsigned long len;
> + int res = 0;
> +
> + if (cpm_debug > 1)
> + printk("cpm_iic_tryaddress(cpm=%p,addr=%d)\n", cpm, addr);
> +
> + /* check for and use a microcode relocation patch */
> + if (cpm->reloc) {
> + cpm_reset_iic_params(iip);
> + }
> +
> + if (cpm_debug && addr == 0) {
> + printk("iip %p, dp_addr 0x%x\n", cpm->iip, cpm->dp_addr);
> + printk("iic_tbase %d, r_tbase %d\n", iip->iic_tbase, r_tbase);
> + }
> +
> + tbdf = (cbd_t *) cpm_dpram_addr(iip->iic_tbase);
> + rbdf = (cbd_t *) cpm_dpram_addr(iip->iic_rbase);
> +
> + tb = cpm->temp;
> + tb = (u_char *) (((uint) tb + 15) & ~15);
> +
> + /* do a simple read */
> + tb[0] = (addr << 1) | 1; /* device address (+ read) */
> + len = 2;
> +
> + flush_dcache_range((unsigned long)tb, (unsigned long)(tb + 2));
> +
> + tbdf->cbd_bufaddr = __pa(tb);
> + tbdf->cbd_datlen = len;
> + tbdf->cbd_sc = BD_SC_READY | BD_SC_LAST | BD_SC_WRAP | BD_IIC_START;
> +
> + rbdf->cbd_datlen = 0;
> + rbdf->cbd_bufaddr = __pa(tb + 2);
> + rbdf->cbd_sc = BD_SC_EMPTY | BD_SC_WRAP | BD_SC_INTRPT;
> +
> + out_8(&i2c->i2c_i2cmr, 0x13); /* Enable some interupts */
> + out_8(&i2c->i2c_i2cer, 0xff);
> + out_8(&i2c->i2c_i2mod, in_8(&i2c->i2c_i2mod) | 1); /* Enable */
> + out_8(&i2c->i2c_i2com, in_8(&i2c->i2c_i2com) | 0x80); /* Begin transmission */
> +
> + if (cpm_debug > 1)
> + printk("about to sleep\n");
> +
> + /* wait for IIC transfer */
> + res = wait_event_interruptible_timeout(iic_wait, 0, 1 * HZ);
> +
> +#ifdef I2C_CHIP_ERRATA
> + /* Chip errata, clear enable. This is not needed on rev D4 CPUs.
> + Disabling I2C too early may cause too short stop condition */
> + udelay(4);
> + out_8(&i2c->i2c_i2mod, in_8(&i2c->i2c_i2mod) | ~1);
> +#endif
> +
> + if ( res < 0) {
> + force_close(cpm);
> + if (cpm_debug)
> + printk("IIC tryaddress: timeout!\n");
> + return -EIO;
> + }
> +
> + if (cpm_debug > 1)
> + printk("back from sleep\n");
> +
> + if (tbdf->cbd_sc & BD_SC_NAK) {
> + if (cpm_debug > 1)
> + printk("IIC try; no ack\n");
> + return 0;
> + }
> +
> + if (tbdf->cbd_sc & BD_SC_READY) {
> + printk("IIC try; complete but tbuf ready\n");
> + }
> +
> + return 1;
> +}
> +
> +static int cpm_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
> +{
> + struct i2c_algo_8xx_data *cpm = adap->algo_data;
> + struct i2c_msg *pmsg;
> + int i, ret;
> + u_char addr;
> +
> + for (i = 0; i < num; i++) {
> + pmsg = &msgs[i];
> +
> + if (cpm_debug)
> + printk("i2c-algo-8xx.o: "
> + "#%d addr=0x%x flags=0x%x len=%d\n buf=%lx\n",
> + i, pmsg->addr, pmsg->flags, pmsg->len,
> + (unsigned long)pmsg->buf);
> +
> + addr = pmsg->addr << 1;
> + if (pmsg->flags & I2C_M_RD)
> + addr |= 1;
> + if (pmsg->flags & I2C_M_REV_DIR_ADDR)
> + addr ^= 1;
> +
> + if (!(pmsg->flags & I2C_M_NOSTART)) {
> + }
> + if (pmsg->flags & I2C_M_RD) {
> + /* read bytes into buffer */
> + ret = cpm_iic_read(cpm, addr, pmsg->buf, pmsg->len);
> + if (cpm_debug)
> + printk("i2c-algo-8xx.o: read %d bytes\n", ret);
> + if (ret < pmsg->len) {
> + return (ret < 0) ? ret : -EREMOTEIO;
> + }
> + } else {
> + /* write bytes from buffer */
> + ret = cpm_iic_write(cpm, addr, pmsg->buf, pmsg->len);
> + if (cpm_debug)
> + printk("i2c-algo-8xx.o: wrote %d\n", ret);
> + if (ret < pmsg->len) {
> + return (ret < 0) ? ret : -EREMOTEIO;
> + }
> + }
> + }
> + return (num);
> +}
> +
> +static u32 cpm_func(struct i2c_adapter *adap)
> +{
> + return I2C_FUNC_SMBUS_EMUL | I2C_FUNC_10BIT_ADDR |
> + I2C_FUNC_PROTOCOL_MANGLING;
> +}
> +
> +/* -----exported algorithm data: ------------------------------------- */
> +
> +static struct i2c_algorithm cpm_algo = {
> + .master_xfer = cpm_xfer,
> + .functionality = cpm_func,
> +};
> +
> +/*
> + * registering functions to load algorithms at runtime
> + */
> +int i2c_8xx_add_bus(struct i2c_adapter *adap)
> +{
> + struct i2c_algo_8xx_data *cpm = adap->algo_data;
> + int i;
> +
> + if (cpm_debug)
> + printk("i2c-algo-8xx.o: hw routines for %s registered.\n",
> + adap->name);
> +
> + /* register new adapter to i2c module... */
> +
> + adap->algo = &cpm_algo;
> +
> + i2c_add_adapter(adap);
> + cpm_iic_init(cpm);
> +
> + /* scan bus */
> + if (cpm_scan) {
> + printk(KERN_INFO " i2c-algo-8xx.o: scanning bus %s...\n",
> + adap->name);
> + for (i = 0; i < 128; i++) {
> + if (cpm_iic_tryaddress(cpm, i))
> + printk("(%02x)",i<<1);
> + }
> + printk("\n");
> + }
> +
> + return 0;
> +}
> +
> +int i2c_8xx_del_bus(struct i2c_adapter *adap)
> +{
> + struct i2c_algo_8xx_data *cpm = adap->algo_data;
> +
> + cpm_iic_shutdown(cpm);
> +
> + return i2c_del_adapter(adap);
> +}
> +
> +EXPORT_SYMBOL(i2c_8xx_add_bus);
> +EXPORT_SYMBOL(i2c_8xx_del_bus);
> +
> +MODULE_AUTHOR("Brad Parker <brad@heeltoe.com>");
> +MODULE_DESCRIPTION("I2C-Bus MPC8XX algorithm");
> +MODULE_LICENSE("GPL");
> diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
> index 4afc795..83d9aef 100644
> --- a/drivers/i2c/busses/Kconfig
> +++ b/drivers/i2c/busses/Kconfig
> @@ -385,8 +385,8 @@ config I2C_PROSAVAGE
> will be called i2c-prosavage.
>
> config I2C_RPXLITE
> - tristate "Embedded Planet RPX Lite/Classic support"
> - depends on RPXLITE || RPXCLASSIC
> + tristate "Embedded Planet RPX Lite/Classic and Freescale 86x/885 ads support"
> + depends on RPXLITE || RPXCLASSIC || MPC86XADS || MPC885ADS
> select I2C_ALGO8XX
>
> config I2C_S3C2410
> diff --git a/drivers/i2c/busses/i2c-rpx.c b/drivers/i2c/busses/i2c-rpx.c
> index 8764df0..ebddd94 100644
> --- a/drivers/i2c/busses/i2c-rpx.c
> +++ b/drivers/i2c/busses/i2c-rpx.c
> @@ -14,88 +14,129 @@
> #include <linux/kernel.h>
> #include <linux/module.h>
> #include <linux/init.h>
> +#include <linux/io.h>
> #include <linux/stddef.h>
> +#include <linux/platform_device.h>
> #include <linux/i2c.h>
> #include <linux/i2c-algo-8xx.h>
> #include <asm/mpc8xx.h>
> #include <asm/commproc.h>
> +#include <asm/fs_pd.h>
>
>
> -static void
> -rpx_iic_init(struct i2c_algo_8xx_data *data)
> +struct m8xx_i2c {
> + char *base;
> + struct device *dev;
> + struct i2c_adapter adap;
> + struct i2c_algo_8xx_data *algo_8xx;
> +};
> +
> +static struct i2c_algo_8xx_data rpx_data;
> +
> +static struct i2c_adapter rpx_ops = {
> + .owner = THIS_MODULE,
> + .name = "m8xx",
> + .id = I2C_HW_MPC8XX_EPON,
> + .algo_data = &rpx_data,
> +};
> +
> +static int rpx_iic_init(struct m8xx_i2c *i2c)
> {
> volatile cpm8xx_t *cp;
> - volatile immap_t *immap;
> + struct resource *r;
> + struct i2c_algo_8xx_data *data = i2c->algo_8xx;
> + struct platform_device *pdev = to_platform_device(i2c->dev);
> +
> + cp = data->cp = (cpm8xx_t *)immr_map(im_cpm); /* pointer to Communication Processor */
>
> - cp = cpmp; /* Get pointer to Communication Processor */
> - immap = (immap_t *)IMAP_ADDR; /* and to internal registers */
> + data->irq = platform_get_irq_byname(pdev, "interrupt");
> +
> + if (data->irq < 0)
> + return -EINVAL;
>
> - data->iip = (iic_t *)&cp->cp_dparam[PROFF_IIC];
> + r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pram");
> + data->iip = ioremap(r->start, r->end - r->start + 1);
> + if (data->iip == NULL)
> + return -EINVAL;
>
> /* Check for and use a microcode relocation patch.
> - */
> + */
> if ((data->reloc = data->iip->iic_rpbase))
> data->iip = (iic_t *)&cp->cp_dpmem[data->iip->iic_rpbase];
>
> - data->i2c = (i2c8xx_t *)&(immap->im_i2c);
> - data->cp = cp;
> -
> - /* Initialize Port B IIC pins.
> - */
> - cp->cp_pbpar |= 0x00000030;
> - cp->cp_pbdir |= 0x00000030;
> - cp->cp_pbodr |= 0x00000030;
> + r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "regs");
> + data->i2c = ioremap(r->start, r->end - r->start + 1);
> + if (data->i2c == NULL)
> + return -EINVAL;
>
> /* Allocate space for two transmit and two receive buffer
> * descriptors in the DP ram.
> */
> data->dp_addr = cpm_dpalloc(sizeof(cbd_t) * 4, 8);
> -
> - /* ptr to i2c area */
> - data->i2c = (i2c8xx_t *)&(((immap_t *)IMAP_ADDR)->im_i2c);
> }
>
> -static int rpx_install_isr(int irq, void (*func)(void *), void *data)
> +static int i2c_rpx_probe(struct device *device)
> {
> - /* install interrupt handler */
> - cpm_install_handler(irq, func, data);
> -
> - return 0;
> -}
> + int result = 0;
> + struct m8xx_i2c *i2c;
> + struct platform_device *pdev = to_platform_device(device);
>
> -static struct i2c_algo_8xx_data rpx_data = {
> - .setisr = rpx_install_isr
> -};
> + if (!(i2c = kmalloc(sizeof(*i2c), GFP_KERNEL))) {
> + return -ENOMEM;
> + }
> + memset(i2c, 0, sizeof(*i2c));
> + i2c->dev = device;
> + i2c->algo_8xx = &rpx_data;
>
> -static struct i2c_adapter rpx_ops = {
> - .owner = THIS_MODULE,
> - .name = "m8xx",
> - .id = I2C_HW_MPC8XX_EPON,
> - .algo_data = &rpx_data,
> -};
> + rpx_iic_init(i2c);
>
> -int __init i2c_rpx_init(void)
> -{
> - printk(KERN_INFO "i2c-rpx: i2c MPC8xx driver\n");
> + dev_set_drvdata(device, i2c);
>
> - /* reset hardware to sane state */
> - rpx_iic_init(&rpx_data);
> + i2c->adap = rpx_ops;
> + i2c_set_adapdata(&i2c->adap, i2c);
> + i2c->adap.dev.parent = &pdev->dev;
>
> - if (i2c_8xx_add_bus(&rpx_ops) < 0) {
> + if ((result = i2c_8xx_add_bus(&rpx_ops) < 0)) {
> printk(KERN_ERR "i2c-rpx: Unable to register with I2C\n");
> - return -ENODEV;
> + kfree(i2c);
> }
>
> + return result;
> +}
> +
> +
> +static int i2c_rpx_remove(struct device *device)
> +{
> + struct m8xx_i2c *i2c = dev_get_drvdata(device);
> +
> + i2c_8xx_del_bus(&i2c->adap);
> + dev_set_drvdata(device, NULL);
> +
> + kfree(i2c);
> return 0;
> }
>
> -void __exit i2c_rpx_exit(void)
> +
> +/* Structure for a device driver */
> +static struct device_driver i2c_rpx_driver = {
> + .name = "fsl-i2c-cpm",
> + .bus = &platform_bus_type,
> + .probe = i2c_rpx_probe,
> + .remove = i2c_rpx_remove,
> +};
> +
> +static int __init i2c_rpx_init(void)
> {
> - i2c_8xx_del_bus(&rpx_ops);
> + return driver_register(&i2c_rpx_driver);
> }
>
> -MODULE_AUTHOR("Dan Malek <dmalek@jlc.net>");
> -MODULE_DESCRIPTION("I2C-Bus adapter routines for MPC8xx boards");
> +static void __exit i2c_rpx_exit(void)
> +{
> + driver_unregister(&i2c_rpx_driver);
> +}
>
> module_init(i2c_rpx_init);
> module_exit(i2c_rpx_exit);
> +
> +MODULE_AUTHOR("Dan Malek <dmalek@jlc.net>");
> +MODULE_DESCRIPTION("I2C-Bus adapter routines for MPC8xx boards");
> diff --git a/include/linux/i2c-algo-8xx.h b/include/linux/i2c-algo-8xx.h
> new file mode 100644
> index 0000000..a644512
> --- /dev/null
> +++ b/include/linux/i2c-algo-8xx.h
> @@ -0,0 +1,29 @@
> +/* ------------------------------------------------------------------------- */
> +/* i2c-algo-8xx.h i2c driver algorithms for MPX8XX CPM */
> +/* ------------------------------------------------------------------------- */
> +
> +/* $Id$ */
> +
> +#ifndef I2C_ALGO_8XX_H
> +#define I2C_ALGO_8XX_H
> +
> +#include <linux/i2c.h>
> +#include <asm/8xx_immap.h>
> +#include <asm/commproc.h>
> +
> +struct i2c_algo_8xx_data {
> + uint dp_addr;
> + int reloc;
> + int irq;
> + i2c8xx_t *i2c;
> + iic_t *iip;
> + cpm8xx_t *cp;
> +
> + u_char temp[513];
> +};
> +
> +extern int i2c_8xx_add_bus(struct i2c_adapter *);
> +extern int i2c_8xx_del_bus(struct i2c_adapter *);
> +
> +#endif /* I2C_ALGO_8XX_H */
> +
>
>
> --
> Sincerely, Vitaly
>
> _______________________________________________
> Linuxppc-dev mailing list
> Linuxppc-dev@ozlabs.org
> https://ozlabs.org/mailman/listinfo/linuxppc-dev
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2007-04-23 04:41    [W:3.359 / U:0.012 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site