lkml.org 
[lkml]   [2007]   [Apr]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    SubjectAHCI exception, ext3 journal aborted on a VIA K8M890 / VT8251
    Hi everyone,

    I have had a lot trouble with my AHCI controller from kernel version
    2.6.19-rc1 to 2.6.21-rc5. The device is detected but the disks never
    spinup and thus the rootfs is never found.

    I finally was able to get Fedora's 2.6.20 and my 2.6.21-rc5 to boot
    with pci=nomsi but I have been getting ext3 errors because the SATA
    controller seems to die. It has happened 3 times today and has never
    happened with my previous 2.6.18 kernel. The last time it happened I
    was rsync'ing about 3GB of files at 30KB/sec and I was away from the
    keyboard, LCD off etc. The first time it happened was after my daily
    crons jobs run which are very disk intensive and I was again away from
    the keyboard. The second time was during another rsync at 30KB/sec I
    believe I was browsing the web but can't really be certain.

    The error seems to occur when the machine is not idle; usually when I
    am uploading a lot of files or scanning the disk (i.e. find / ). I
    can't be certain of the trigger so any help isolating it would be
    appreciated. I have stripped out any non-free modules (VMware and
    fglrx) and am in the process of compiling a vanilla 2.6.20 kernel in
    order to exclude any Fedora-isms.

    My hardware components are the following:

    Motherboard: A8V-VM Socket 939 VIA K8M890 / VT8251
    CPU: Opteron 165 dual core
    Harddisk: SATA 1.5Gbps WD 160GB drive

    Most relevant snippet from dmesg, (you can see a longer version below):

    ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
    ata1.00: cmd ca/00:08:c5:b6:03/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 out
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    ata1: soft resetting port
    ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    ata1.00: qc timeout (cmd 0xec)
    ata1.00: failed to IDENTIFY (I/O error, err_mask=0x104)
    ata1.00: revalidation failed (errno=-5)
    ata1: failed to recover some devices, retrying in 5 secs
    ata1: hard resetting port


    What other information can I provide that would be helpful?


    Thanks,
    Stephen


    ==============


    * uname -a
    Linux small 2.6.20-1.2307.fc5smp #1 SMP Sun Mar 18 21:02:16 EDT 2007
    i686 athlon i386 GNU/Linux

    * Kernel commmand line
    ro root=/dev/VolGroup00/LogVol00 rhgb quiet selinux=0 pci=nomsi

    * /sbin/lsmod

    Module Size Used by
    fuse 46805 2
    nfsd 208561 17
    exportfs 9921 1 nfsd
    lockd 62921 2 nfsd
    nfs_acl 7745 1 nfsd
    autofs4 24517 1
    hidp 23745 2
    l2cap 30785 5 hidp
    bluetooth 58149 2 hidp,l2cap
    sunrpc 153853 12 nfsd,lockd,nfs_acl
    ipt_REJECT 8769 1
    nf_conntrack_ipv4 21837 5
    xt_state 6721 5
    nf_conntrack 62665 2 nf_conntrack_ipv4,xt_state
    nfnetlink 11097 2 nf_conntrack_ipv4,nf_conntrack
    xt_tcpudp 7361 6
    iptable_filter 7233 1
    ip_tables 16517 1 iptable_filter
    x_tables 19013 4 ipt_REJECT,xt_state,xt_tcpudp,ip_tables
    loop 20297 0
    video 20037 0
    sbs 19201 0
    i2c_ec 9153 1 sbs
    dock 14233 0
    button 11985 0
    battery 14021 0
    asus_acpi 20573 0
    backlight 10433 1 asus_acpi
    ac 9285 0
    ipv6 275585 18
    lp 16521 0
    parport_pc 30309 0
    parport 38793 2 lp,parport_pc
    cdc_acm 19169 0
    snd_emu10k1 114657 1
    snd_rawmidi 27073 1 snd_emu10k1
    snd_ac97_codec 93541 1 snd_emu10k1
    ac97_bus 6593 1 snd_ac97_codec
    snd_seq_dummy 8005 0
    snd_seq_oss 33857 0
    snd_seq_midi_event 11329 1 snd_seq_oss
    snd_seq 51505 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
    snd_pcm_oss 43873 0
    snd_mixer_oss 19649 1 snd_pcm_oss
    snd_pcm 75461 3 snd_emu10k1,snd_ac97_codec,snd_pcm_oss
    snd_seq_device 11981 5
    snd_emu10k1,snd_rawmidi,snd_seq_dummy,snd_seq_oss,snd_seq
    snd_timer 25413 3 snd_emu10k1,snd_seq,snd_pcm
    snd_page_alloc 14153 2 snd_emu10k1,snd_pcm
    snd_util_mem 8897 1 snd_emu10k1
    snd_hwdep 12997 1 snd_emu10k1
    ehci_hcd 34901 0
    sg 37341 0
    i2c_viapro 12885 0
    emu10k1_gp 8129 0
    snd 53957 13
    snd_emu10k1,snd_rawmidi,snd_ac97_codec,snd_seq_oss,snd_seq,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_device,snd_timer,snd_hwdep
    uhci_hcd 27089 0
    k8temp 9665 0
    via_rhine 28877 0
    gameport 19529 2 emu10k1_gp
    soundcore 11937 1 snd
    hwmon 7621 1 k8temp
    serio_raw 11077 0
    i2c_core 25153 2 i2c_ec,i2c_viapro
    k8_edac 18689 0
    mii 9537 1 via_rhine
    edac_mc 25929 1 k8_edac
    pcspkr 7361 0
    dm_snapshot 20849 0
    dm_zero 6209 0
    dm_mirror 25301 0
    dm_mod 58253 8 dm_snapshot,dm_zero,dm_mirror
    ahci 25541 2
    libata 104793 1 ahci
    sd_mod 24129 3
    scsi_mod 138221 4 sg,ahci,libata,sd_mod
    ext3 126025 2
    jbd 60777 1 ext3


    * Full error log

    ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
    ata1.00: cmd ca/00:08:c5:b6:03/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 out
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    ata1: soft resetting port
    ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    ata1.00: qc timeout (cmd 0xec)
    ata1.00: failed to IDENTIFY (I/O error, err_mask=0x104)
    ata1.00: revalidation failed (errno=-5)
    ata1: failed to recover some devices, retrying in 5 secs
    ata1: hard resetting port
    ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    ata1.00: qc timeout (cmd 0xec)
    ata1.00: failed to IDENTIFY (I/O error, err_mask=0x104)
    ata1.00: revalidation failed (errno=-5)
    ata1: failed to recover some devices, retrying in 5 secs
    ata1: hard resetting port
    ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    ata1.00: qc timeout (cmd 0xec)
    ata1.00: failed to IDENTIFY (I/O error, err_mask=0x104)
    ata1.00: revalidation failed (errno=-5)
    ata1.00: disabled
    ata1: EH complete
    sd 0:0:0:0: SCSI error: return code = 0x00040000
    end_request: I/O error, dev sda, sector 243397
    Buffer I/O error on device dm-0, logical block 4271
    lost page write due to I/O error on dm-0
    Aborting journal on device dm-0.
    sd 0:0:0:0: SCSI error: return code = 0x00040000
    end_request: I/O error, dev sda, sector 112310605
    sd 0:0:0:0: SCSI error: return code = 0x00040000
    end_request: I/O error, dev sda, sector 112310861
    sd 0:0:0:0: SCSI error: return code = 0x00040000
    end_request: I/O error, dev sda, sector 178467397
    Buffer I/O error on device dm-0, logical block 22282271
    lost page write due to I/O error on dm-0
    sd 0:0:0:0: SCSI error: return code = 0x00040000
    end_request: I/O error, dev sda, sector 200427245
    Buffer I/O error on device dm-0, logical block 25027252
    lost page write due to I/O error on dm-0
    Buffer I/O error on device dm-0, logical block 25027253
    lost page write due to I/O error on dm-0
    Buffer I/O error on device dm-0, logical block 25027254
    lost page write due to I/O error on dm-0
    sd 0:0:0:0: SCSI error: return code = 0x00040000
    end_request: I/O error, dev sda, sector 263139949
    Buffer I/O error on device dm-0, logical block 32866340
    lost page write due to I/O error on dm-0
    sd 0:0:0:0: SCSI error: return code = 0x00040000
    end_request: I/O error, dev sda, sector 263140573
    Buffer I/O error on device dm-0, logical block 32866418
    lost page write due to I/O error on dm-0
    sd 0:0:0:0: SCSI error: return code = 0x00040000
    end_request: I/O error, dev sda, sector 263141469
    Buffer I/O error on device dm-0, logical block 32866530
    lost page write due to I/O error on dm-0
    sd 0:0:0:0: SCSI error: return code = 0x00040000
    end_request: I/O error, dev sda, sector 98513277
    Buffer I/O error on device dm-0, logical block 12288006
    lost page write due to I/O error on dm-0
    sd 0:0:0:0: SCSI error: return code = 0x00040000
    EXT3-fs error (device dm-0) in ext3_reserve_inode_write: Journal has aborted
    end_request: I/O error, dev sda, sector 98595781
    Buffer I/O error on device dm-0, logical block 12298319
    lost page write due to I/O error on dm-0
    sd 0:0:0:0: SCSI error: return code = 0x00040000
    end_request: I/O error, dev sda, sector 112310605
    ext3_abort called.
    EXT3-fs error (device dm-0): ext3_journal_start_sb: Detected aborted journal
    Remounting filesystem read-only
    sd 0:0:0:0: SCSI error: return code = 0x00040000
    end_request: I/O error, dev sda, sector 209229
    sd 0:0:0:0: SCSI error: return code = 0x00040000
    end_request: I/O error, dev sda, sector 112310605
    sd 0:0:0:0: SCSI error: return code = 0x00040000
    end_request: I/O error, dev sda, sector 200427245
    journal commit I/O error
    sd 0:0:0:0: SCSI error: return code = 0x00040000
    end_request: I/O error, dev sda, sector 112310861
    sd 0:0:0:0: SCSI error: return code = 0x00040000
    end_request: I/O error, dev sda, sector 112311373
    sd 0:0:0:0: SCSI error: return code = 0x00040000
    end_request: I/O error, dev sda, sector 112311885
    sd 0:0:0:0: SCSI error: return code = 0x00040000
    end_request: I/O error, dev sda, sector 112110789


    * dmesg

    Linux version 2.6.20-1.2307.fc5smp
    (brewbuilder@hs20-bc1-6.build.redhat.com) (gcc version 4.1.1 20070105
    (Red Hat 4.1.1-51)) #1 SMP Sun Mar 18 21:02:16 EDT 2007
    BIOS-provided physical RAM map:
    sanitize start
    sanitize end
    copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end:
    000000000009fc00 type: 1
    copy_e820_map() type is E820_RAM
    copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end:
    00000000000a0000 type: 2
    copy_e820_map() start: 00000000000e4000 size: 000000000001c000 end:
    0000000000100000 type: 2
    copy_e820_map() start: 0000000000100000 size: 000000007feb0000 end:
    000000007ffb0000 type: 1
    copy_e820_map() type is E820_RAM
    copy_e820_map() start: 000000007ffb0000 size: 000000000000e000 end:
    000000007ffbe000 type: 3
    copy_e820_map() start: 000000007ffbe000 size: 0000000000022000 end:
    000000007ffe0000 type: 4
    copy_e820_map() start: 000000007ffe0000 size: 0000000000020000 end:
    0000000080000000 type: 2
    copy_e820_map() start: 00000000fec00000 size: 0000000000001000 end:
    00000000fec01000 type: 2
    copy_e820_map() start: 00000000fecc0000 size: 0000000000001000 end:
    00000000fecc1000 type: 2
    copy_e820_map() start: 00000000ff780000 size: 0000000000880000 end:
    0000000100000000 type: 2
    BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000007ffb0000 (usable)
    BIOS-e820: 000000007ffb0000 - 000000007ffbe000 (ACPI data)
    BIOS-e820: 000000007ffbe000 - 000000007ffe0000 (ACPI NVS)
    BIOS-e820: 000000007ffe0000 - 0000000080000000 (reserved)
    BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
    BIOS-e820: 00000000fecc0000 - 00000000fecc1000 (reserved)
    BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
    1151MB HIGHMEM available.
    896MB LOWMEM available.
    found SMP MP-table at 000ff780
    NX (Execute Disable) protection: active
    Entering add_active_range(0, 0, 524208) 0 entries of 256 used
    Zone PFN ranges:
    DMA 0 -> 4096
    Normal 4096 -> 229376
    HighMem 229376 -> 524208
    early_node_map[1] active PFN ranges
    0: 0 -> 524208
    On node 0 totalpages: 524208
    DMA zone: 40 pages used for memmap
    DMA zone: 0 pages reserved
    DMA zone: 4056 pages, LIFO batch:0
    Normal zone: 2200 pages used for memmap
    Normal zone: 223080 pages, LIFO batch:31
    HighMem zone: 2879 pages used for memmap
    HighMem zone: 291953 pages, LIFO batch:31
    DMI 2.3 present.
    Using APIC driver default
    ACPI: RSDP (v002 ACPIAM ) @ 0x000fa850
    ACPI: XSDT (v001 A M I OEMXSDT 0x06000619 MSFT 0x00000097) @ 0x7ffb0100
    ACPI: FADT (v003 A M I OEMFACP 0x06000619 MSFT 0x00000097) @ 0x7ffb0290
    ACPI: MADT (v001 A M I OEMAPIC 0x06000619 MSFT 0x00000097) @ 0x7ffb0390
    ACPI: MCFG (v001 A M I OEMMCFG 0x06000619 MSFT 0x00000097) @ 0x7ffb0400
    ACPI: OEMB (v001 A M I AMI_OEM 0x06000619 MSFT 0x00000097) @ 0x7ffbe040
    ACPI: DSDT (v001 A0339 A0339000 0x00000000 INTL 0x02002026) @ 0x00000000
    ACPI: PM-Timer IO Port: 0x808
    ACPI: Local APIC address 0xfee00000
    ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
    Processor #0 15:3 APIC version 16
    ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
    Processor #1 15:3 APIC version 16
    ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
    IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
    ACPI: IOAPIC (id[0x03] address[0xfecc0000] gsi_base[24])
    IOAPIC[1]: apic_id 3, version 3, address 0xfecc0000, GSI 24-47
    ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
    ACPI: IRQ0 used by override.
    ACPI: IRQ2 used by override.
    ACPI: IRQ9 used by override.
    Enabling APIC mode: Flat. Using 2 I/O APICs
    Using ACPI (MADT) for SMP configuration information
    Allocating PCI resources starting at 88000000 (gap: 80000000:7ec00000)
    Detected 1800.236 MHz processor.
    Built 1 zonelists. Total pages: 519089
    Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet
    selinux=0 pci=nomsi
    mapped APIC to ffffd000 (fee00000)
    mapped IOAPIC to ffffc000 (fec00000)
    mapped IOAPIC to ffffb000 (fecc0000)
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Initializing CPU#0
    CPU 0 irqstacks, hard=c076d000 soft=c074d000
    PID hash table entries: 4096 (order: 12, 16384 bytes)
    Console: colour VGA+ 80x25
    Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    Memory: 2068256k/2096832k available (2181k kernel code, 27368k
    reserved, 915k data, 240k init, 1179328k highmem)
    virtual kernel memory layout:
    fixmap : 0xffc56000 - 0xfffff000 (3748 kB)
    pkmap : 0xffa00000 - 0xffc00000 (2048 kB)
    vmalloc : 0xf8800000 - 0xff9fe000 ( 113 MB)
    lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
    .init : 0xc070c000 - 0xc0748000 ( 240 kB)
    .data : 0xc0621575 - 0xc0706494 ( 915 kB)
    .text : 0xc0400000 - 0xc0621575 (2181 kB)
    Checking if this processor honours the WP bit even in supervisor mode... Ok.
    Calibrating delay using timer specific routine.. 3601.63 BogoMIPS (lpj=1800818)
    Security Framework v1.0.0 initialized
    SELinux: Disabled at boot.
    Capability LSM initialized
    Mount-cache hash table entries: 512
    CPU: After generic identify, caps: 178bfbff e3d3fbff 00000000 00000000
    00000001 00000000 00000003
    CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
    CPU: L2 Cache: 1024K (64 bytes/line)
    CPU 0(2) -> Core 0
    CPU: After all inits, caps: 178bfbff e3d3fbff 00000000 00000410
    00000001 00000000 00000003
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    Checking 'hlt' instruction... OK.
    SMP alternatives: switching to UP code
    ACPI: Core revision 20060707
    CPU0: AMD Dual Core AMD Opteron(tm) Processor 165 stepping 02
    SMP alternatives: switching to SMP code
    Booting processor 1/1 eip 3000
    CPU 1 irqstacks, hard=c076e000 soft=c074e000
    Initializing CPU#1
    Calibrating delay using timer specific routine.. 3599.65 BogoMIPS (lpj=1799827)
    CPU: After generic identify, caps: 178bfbff e3d3fbff 00000000 00000000
    00000001 00000000 00000003
    CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
    CPU: L2 Cache: 1024K (64 bytes/line)
    CPU 1(2) -> Core 1
    CPU: After all inits, caps: 178bfbff e3d3fbff 00000000 00000410
    00000001 00000000 00000003
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#1.
    CPU1: AMD Dual Core AMD Opteron(tm) Processor 165 stepping 02
    Total of 2 processors activated (7201.29 BogoMIPS).
    ENABLING IO-APIC IRQs
    ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0
    checking TSC synchronization across 2 CPUs:
    CPU#0 had -84 usecs TSC skew, fixed it up.
    CPU#1 had 84 usecs TSC skew, fixed it up.
    Brought up 2 CPUs
    sizeof(vma)=88 bytes
    sizeof(page)=40 bytes
    sizeof(inode)=420 bytes
    sizeof(dentry)=144 bytes
    sizeof(ext3inode)=596 bytes
    sizeof(buffer_head)=56 bytes
    sizeof(skbuff)=176 bytes
    sizeof(task_struct)=1424 bytes
    migration_cost=345
    NET: Registered protocol family 16
    ACPI: bus type pci registered
    PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
    PCI: Not using MMCONFIG.
    PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5
    PCI: Using configuration type 1
    Setting up standard PCI resources
    ACPI: Interpreter enabled
    ACPI: Using IOAPIC for interrupt routing
    ACPI: PCI Root Bridge [PCI0] (0000:00)
    PCI: Probing PCI hardware (bus 00)
    0000:00:0f.1: cannot adjust BAR0 (not I/O)
    0000:00:0f.1: cannot adjust BAR1 (not I/O)
    0000:00:0f.1: cannot adjust BAR2 (not I/O)
    0000:00:0f.1: cannot adjust BAR3 (not I/O)
    Boot video device is 0000:02:00.0
    PCI: Transparent bridge - 0000:00:13.1
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NBPG._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PA._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
    ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 *15)
    ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *10 11 12 14 15)
    Linux Plug and Play Support v0.97 (c) Adam Belay
    pnp: PnP ACPI init
    pnp: PnP ACPI: found 11 devices
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    PCI: Using ACPI for IRQ routing
    PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
    NetLabel: Initializing
    NetLabel: domain hash size = 128
    NetLabel: protocols = UNLABELED CIPSOv4
    NetLabel: unlabeled traffic allowed by default
    pnp: 00:05: ioport range 0x290-0x297 has been reserved
    PCI: Bridge: 0000:00:01.0
    IO window: disabled.
    MEM window: disabled.
    PREFETCH window: disabled.
    PCI: Bridge: 0000:00:02.0
    IO window: d000-dfff
    MEM window: fbf00000-fbffffff
    PREFETCH window: d0000000-dfffffff
    PCI: Bridge: 0000:00:13.0
    IO window: disabled.
    MEM window: disabled.
    PREFETCH window: disabled.
    PCI: Bridge: 0000:00:13.1
    IO window: e000-efff
    MEM window: disabled.
    PREFETCH window: disabled.
    PCI: Setting latency timer of device 0000:00:01.0 to 64
    ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 27 (level, low) -> IRQ 16
    PCI: Setting latency timer of device 0000:00:02.0 to 64
    PCI: Setting latency timer of device 0000:00:13.0 to 64
    PCI: Setting latency timer of device 0000:00:13.1 to 64
    NET: Registered protocol family 2
    IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
    TCP established hash table entries: 131072 (order: 9, 2621440 bytes)
    TCP bind hash table entries: 65536 (order: 8, 1310720 bytes)
    TCP: Hash tables configured (established 131072 bind 65536)
    TCP reno registered
    checking if image is initramfs... it is
    Freeing initrd memory: 1830k freed
    apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
    apm: disabled - APM is not SMP safe.
    audit: initializing netlink socket (disabled)
    audit(1175464944.811:1): initialized
    highmem bounce pool size: 64 pages
    Total HugeTLB memory allocated, 0
    VFS: Disk quotas dquot_6.5.1
    Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    ksign: Installing public key data
    Loading keyring
    - Added public key D81E1D1A80E5E114
    - User ID: Red Hat, Inc. (Kernel Module GPG key)
    io scheduler noop registered
    io scheduler anticipatory registered
    io scheduler deadline registered
    io scheduler cfq registered (default)
    PCI: Setting latency timer of device 0000:00:02.0 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[0000:00:02.0:pcie00]
    Allocate Port Service[0000:00:02.0:pcie02]
    pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
    ACPI: Processor [CPU1] (supports 16 throttling states)
    isapnp: Scanning for PnP cards...
    isapnp: No Plug & Play device found
    Real Time Clock Driver v1.12ac
    Non-volatile memory driver v1.2
    Linux agpgart interface v0.101 (c) Dave Jones
    agpgart: Detected AGP bridge 0
    agpgart: AGP aperture is 128M @ 0xf0000000
    Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
    serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
    00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
    RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
    input: Macintosh mouse button emulation as /class/input/input0
    Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    VP_IDE: IDE controller at PCI slot 0000:00:0f.1
    VP_IDE: chipset revision 7
    VP_IDE: not 100% native mode: will probe irqs later
    VP_IDE: VIA vt8251 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
    ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb:pio
    Probing IDE interface ide0...
    Probing IDE interface ide0...
    Probing IDE interface ide1...
    ide-floppy driver 0.99.newide
    usbcore: registered new interface driver libusual
    usbcore: registered new interface driver hiddev
    usbcore: registered new interface driver usbhid
    drivers/usb/input/hid-core.c: v2.6:USB HID core driver
    PNP: No PS/2 controller found. Probing ports directly.
    serio: i8042 KBD port at 0x60,0x64 irq 1
    serio: i8042 AUX port at 0x60,0x64 irq 12
    mice: PS/2 mouse device common for all mice
    TCP bic registered
    Initializing XFRM netlink socket
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    powernow-k8: Found 2 Dual Core AMD Opteron(tm) Processor 165
    processors (version 2.00.00)
    powernow-k8: 0 : fid 0xa (1800 MHz), vid 0x8
    powernow-k8: 1 : fid 0x2 (1000 MHz), vid 0x12
    Using IPI No-Shortcut mode
    ACPI: (supports S0 S1 S3 S4 S5)
    Freeing unused kernel memory: 240k freed
    Write protecting the kernel read-only data: 597k
    Time: acpi_pm clocksource has been installed.
    SCSI subsystem initialized
    libata version 2.00 loaded.
    ahci 0000:00:0f.0: version 2.0
    ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 21 (level, low) -> IRQ 17
    ahci 0000:00:0f.0: AHCI 0001.0000 32 slots 4 ports 3 Gbps 0xf impl SATA mode
    ahci 0000:00:0f.0: flags: 64bit ncq pm led clo pmp pio slum part
    ata1: SATA max UDMA/133 cmd 0xF8806D00 ctl 0x0 bmdma 0x0 irq 17
    ata2: SATA max UDMA/133 cmd 0xF8806D80 ctl 0x0 bmdma 0x0 irq 17
    ata3: SATA max UDMA/133 cmd 0xF8806E00 ctl 0x0 bmdma 0x0 irq 17
    ata4: SATA max UDMA/133 cmd 0xF8806E80 ctl 0x0 bmdma 0x0 irq 17
    scsi0 : ahci
    ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    ata1.00: ATA-6, max UDMA/100, 312581808 sectors: LBA48
    ata1.00: ata1: dev 0 multi count 16
    ata1.00: applying bridge limits
    ata1.00: configured for UDMA/100
    scsi1 : ahci
    ata2: SATA link down (SStatus 0 SControl 300)
    scsi2 : ahci
    ata3: SATA link down (SStatus 0 SControl 300)
    scsi3 : ahci
    ata4: SATA link down (SStatus 0 SControl 300)
    scsi 0:0:0:0: Direct-Access ATA WDC WD1600JD-00F 02.0 PQ: 0 ANSI: 5
    SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
    sda: Write Protect is off
    sda: Mode Sense: 00 3a 00 00
    SCSI device sda: write cache: enabled, read cache: enabled, doesn't
    support DPO or FUA
    SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
    sda: Write Protect is off
    sda: Mode Sense: 00 3a 00 00
    SCSI device sda: write cache: enabled, read cache: enabled, doesn't
    support DPO or FUA
    sda: sda1 sda2
    sd 0:0:0:0: Attached scsi disk sda
    device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
    kjournald starting. Commit interval 5 seconds
    EXT3-fs: mounted filesystem with ordered data mode.
    input: PC Speaker as /class/input/input1
    EDAC MC: Ver: 2.0.1 Mar 18 2007
    EDAC MC0: Giving out device to k8_edac Athlon64/Opteron: DEV 0000:00:18.2
    via-rhine.c:v1.10-LK1.4.2 Sept-11-2006 Written by Donald Becker
    ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 18
    eth0: VIA Rhine II at 0xfbeff400, 00:18:f3:02:37:08, IRQ 18.
    eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link 45e1.
    USB Universal Host Controller Interface driver v3.0
    ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 20 (level, low) -> IRQ 19
    uhci_hcd 0000:00:10.0: UHCI Host Controller
    uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
    uhci_hcd 0000:00:10.0: irq 19, io base 0x0000b000
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:10.1[C] -> GSI 22 (level, low) -> IRQ 20
    uhci_hcd 0000:00:10.1: UHCI Host Controller
    uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
    uhci_hcd 0000:00:10.1: irq 20, io base 0x0000a800
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 17
    uhci_hcd 0000:00:10.2: UHCI Host Controller
    uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
    uhci_hcd 0000:00:10.2: irq 17, io base 0x0000a400
    usb usb3: configuration #1 chosen from 1 choice
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 2 ports detected
    sd 0:0:0:0: Attached scsi generic sg0 type 0
    ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 23 (level, low) -> IRQ 18
    uhci_hcd 0000:00:10.3: UHCI Host Controller
    uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
    uhci_hcd 0000:00:10.3: irq 18, io base 0x0000a000
    usb usb4: configuration #1 chosen from 1 choice
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 22 (level, low) -> IRQ 20
    ehci_hcd 0000:00:10.4: EHCI Host Controller
    ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
    ehci_hcd 0000:00:10.4: debug port 1
    ehci_hcd 0000:00:10.4: irq 20, io mem 0xfbeff800
    ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
    usb usb5: configuration #1 chosen from 1 choice
    hub 5-0:1.0: USB hub found
    hub 5-0:1.0: 8 ports detected
    gameport: EMU10K1 is pci0000:05:09.1/gameport0, io 0xe400, speed 962kHz
    ACPI: PCI Interrupt 0000:05:09.0[A] -> GSI 17 (level, low) -> IRQ 21
    usb 5-4: new high speed USB device using ehci_hcd and address 3
    usb 5-4: configuration #1 chosen from 1 choice
    hub 5-4:1.0: USB hub found
    hub 5-4:1.0: 7 ports detected
    usb 2-1: new full speed USB device using uhci_hcd and address 2
    usb 2-1: configuration #1 chosen from 1 choice
    hub 2-1:1.0: USB hub found
    hub 2-1:1.0: 3 ports detected
    usb 5-4.2: new full speed USB device using ehci_hcd and address 4
    usb 5-4.2: configuration #1 chosen from 2 choices
    usb 2-1.1: new low speed USB device using uhci_hcd and address 3
    usb 2-1.1: configuration #1 chosen from 1 choice
    input: LOGITECH USB Keyboard as /class/input/input2
    input: USB HID v1.10 Keyboard [LOGITECH USB Keyboard] on usb-0000:00:10.1-1.1
    input: LOGITECH USB Keyboard as /class/input/input3
    input: USB HID v1.10 Device [LOGITECH USB Keyboard] on usb-0000:00:10.1-1.1
    usb 2-1.3: new low speed USB device using uhci_hcd and address 4
    usb 2-1.3: configuration #1 chosen from 1 choice
    input: Logitech USB Receiver as /class/input/input4
    input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:10.1-1.3
    cdc_acm 5-4.2:1.0: ttyACM0: USB ACM device
    usbcore: registered new interface driver cdc_acm
    drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver
    for USB modems and ISDN adapters
    floppy0: no floppy controllers found
    lp: driver loaded but no devices found
    NET: Registered protocol family 10
    lo: Disabled Privacy Extensions
    Mobile IPv6
    input: Power Button (FF) as /class/input/input5
    ACPI: Power Button (FF) [PWRF]
    input: Sleep Button (CM) as /class/input/input6
    ACPI: Sleep Button (CM) [SLPB]
    input: Power Button (CM) as /class/input/input7
    ACPI: Power Button (CM) [PWRB]
    No dock devices found.
    ibm_acpi: ec object not found
    md: Autodetecting RAID arrays.
    md: autorun ...
    md: ... autorun DONE.
    loop: loaded (max 8 devices)
    EXT3 FS on dm-0, internal journal
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on sda1, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    Adding 2129912k swap on /dev/VolGroup00/LogVol01. Priority:-1
    extents:1 across:2129912k
    ip_tables: (C) 2000-2006 Netfilter Core Team
    Netfilter messages via NETLINK v0.30.
    nf_conntrack version 0.5.0 (8192 buckets, 65536 max)
    eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
    Bluetooth: Core ver 2.11
    NET: Registered protocol family 31
    Bluetooth: HCI device and connection manager initialized
    Bluetooth: HCI socket layer initialized
    Bluetooth: L2CAP ver 2.8
    Bluetooth: L2CAP socket layer initialized
    Bluetooth: HIDP (Human Interface Emulation) ver 1.1
    eth0: no IPv6 routers present
    Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
    NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
    NFSD: starting 90-second grace period
    eth0: no IPv6 routers present
    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

    \
     
     \ /
      Last update: 2007-04-02 00:43    [W:3.173 / U:0.792 seconds]
    ©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site