lkml.org 
[lkml]   [2007]   [Mar]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] Add support for ITE887x serial chipsets
On Mon, Mar 26, 2007 at 04:17:02PM +0200, Niels de Vos wrote:
> +/*
> + * ITE support by Niels de Vos <niels.devos@wincor-nixdorf.com>
> + */
> +
> +static int __devinit pci_ite887x_init(struct pci_dev *dev)
> +{
> + /* inta_addr are the configuration addresses of the ITE */
> + short inta_addr[] = { 0x2a0, 0x2c0, 0x220, 0x240, 0x1E0, 0x200,
> + 0x280, 0 };
> + int ret, i, type;
> + struct resource *iobase;
> +
> + /* search for the base-ioport */
> + i = 0;
> + while (inta_addr[i] && dev->dev.driver_data != NULL) {
> + dev->dev.driver_data = request_region(inta_addr[i], 32,
> + "ite887x");
> + if (dev->dev.driver_data != NULL) {
> + /* write POSIO0R - speed | size | ioport */
> + pci_write_config_dword(dev, 0x60,
> + 0xe5000000 | inta_addr[i]);
> + /* write INTCBAR - ioport */
> + pci_write_config_dword(dev, 0x78, inta_addr[i]);
> + ret = inb(inta_addr[i]);
> + if (ret != 0xff) {
> + /* ioport connected */
> + break;
> + }
> + release_resource(dev->dev.driver_data);
> + dev->dev.driver_data = NULL;

This doesn't free the memory allocated by request_region. Always
pair release_region() with request_region(). Ditto for all of your
other uses of "release_resource()".

Might also be cleaner to avoid touching dev->dev.driver_data at all
until you've identified a working resource.

> + }
> + i++;
> + }
> +
> + if (! inta_addr[i]) {
> + printk(KERN_ERR "ite887x: could not find iobase\n");
> + return -ENODEV;
> + }
> +
> + iobase = dev->dev.driver_data;
> +
> + /* start of undocumented type checking (see parport_pc.c) */
> + type = inb(iobase->start + 0x18);
> + type &= 0x0f;
> +
> + switch (type) {
> + case 0x2:
> + printk(KERN_DEBUG "8250_pci: ITE8871 found (1P)\n");
> + break;
> + case 0xa:
> + printk(KERN_DEBUG "8250_pci: ITE8875 found (1P)\n");
> + break;
> + case 0xe:
> + printk(KERN_INFO "8250_pci: ITE8872 found (2S1P)\n");
> + return 2;
> + case 0x6:
> + printk(KERN_INFO "8250_pci: ITE8873 found (1S)\n");
> + return 1;
> + case 0x8:
> + printk(KERN_INFO "8250_pci: ITE8874 found (2S)\n");
> + return 2;
> + default:
> + moan_device("unknown ITE887x", dev);
> + }
> +
> + /* the device has no UARTs if we get here */
> + release_resource(iobase);
> + dev->dev.driver_data = NULL;
> + return -ENODEV;
> +}
> +
> +/*
> + * activate the UART in the MISCR
> + */
> +static int
> +pci_ite887x_setup(struct serial_private *priv, struct pciserial_board *board,
> + struct uart_port *port, int idx)
> +{
> + int ret;
> + struct pci_dev *dev = priv->dev;
> + u32 miscr, uartbar, ioport;
> + /* iobase is the private driver_data */
> + struct resource *iobase;
> + /* registers */
> + unsigned short MISCR = 0x9c, UARTBAR = 0x7c;
> + unsigned short PS1BAR = 0x14, POSIO1 = 0x64;
> +
> + /* enable IO_Space bit */
> + u32 POSIO_ENABLE = 1 << 31;
> + /* Decoding speed (1 = slow, 2 = medium, 3 = fast) */
> + u32 POSIO_SPEED = 3 << 29;

#define all of these? They're constants.

> +
> + iobase = (struct resource*) dev->dev.driver_data;
> + if (iobase == NULL) {
> + printk(KERN_ERR "ite887x: iobase is not available\n");
> + return -ENODEV;
> + }
> +
> + /* read the I/O port from the device */
> + ret = pci_read_config_dword(dev, PS1BAR + (0x4 * idx), &ioport);
> + if (ret) {
> + printk(KERN_ERR "ite887x: read error PS%dBAR\n", idx + 1);
> + ret = -ENODEV;
> + goto release_inta;
> + }
> +
> + ioport &= 0x0000FF00; /* the actual I/O space base address */
> + ret = pci_write_config_dword(dev, POSIO1 + (0x4 * idx),
> + POSIO_ENABLE | POSIO_SPEED | ioport);
> + if (ret) {
> + printk(KERN_ERR "ite887x: write error PSIO%d+\n", idx + 1);
> + ret = -ENODEV;
> + goto release_inta;
> + }
> +
> + /* write the ioport to the UARTBAR */
> + ret = pci_read_config_dword(dev, UARTBAR, &uartbar);
> + if (ret) {
> + printk(KERN_ERR "ite887x: read error UARTBAR\n");
> + ret = -ENODEV;
> + goto release_inta;
> + }
> + uartbar &= ~(15 << (4 * idx)); /* clear half the reg */
> + uartbar |= ioport << (16 * idx); /* set the ioport */
> + ret = pci_write_config_dword(dev, UARTBAR, uartbar);
> + if (ret) {
> + printk(KERN_ERR "ite887x: write error UARTBAR\n");
> + ret = -ENODEV;
> + goto release_inta;
> + }
> +
> + /* get current config */
> + ret = pci_read_config_dword(dev, MISCR, &miscr);
> + if (ret) {
> + printk(KERN_ERR "ite887x: read error MISCR\n");
> + ret = -ENODEV;
> + goto release_inta;
> + }
> +
> + /* disable interrupts (UARTx_Routing[3:0]) */
> + miscr &= ~(0xf << (12 - 4 * idx));
> + /* activate the UART (UARTx_En) */
> + miscr |= 1 << (23 - idx);
> +
> + /* write new config with activated UART */
> + ret = pci_write_config_dword(dev, MISCR, miscr);
> + if (ret) {
> + printk(KERN_ERR "ite887x: write error MISCR\n");
> + ret = -ENODEV;
> + goto release_inta;
> + }

I think all of the above can be done in the init function, which'll be
a _lot_ clearer. That also means...

> +
> + /* idx + 1: using POSIO1 and up */
> + return setup_port(priv, port, idx + 1, board->first_offset, 0);

that you can (usefully) add pbn_b1_bt_1_115200 and completely avoid
this hack.

> @@ -968,6 +1148,7 @@ enum pci_board_num_t {
> pbn_plx_romulus,
> pbn_oxsemi,
> pbn_intel_i960,
> + pbn_ite_887x,

Always avoid chipset specific definitions if there's another way to
work around them (as suggested above).

--
Russell King
Linux kernel 2.6 ARM Linux - http://www.arm.linux.org.uk/
maintainer of:
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2007-03-26 23:17    [W:0.053 / U:0.644 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site