lkml.org 
[lkml]   [2007]   [Mar]   [21]   [last100]   RSS Feed
Views: [more markup]  [less markup]  [headers]  [forward] 
 
Messages in this thread
/
DateTue, 20 Mar 2007 23:52:25 -0700 (PDT)
From"Mr. James W. Laferriere" <>
SubjectRE: MPT Fusion LSI22320 , Domain validation loops .
 	Hello Eric ,  Fyi ,  linux-2.6.21-rc4 + mpt-fusion(*) patches from 
Andrew Morton's patch tree .  Still gives me the ever looping reset .  But I 
have just found sometrhing of interest one of the Powersuplies in the cabiinet 
'May be' failing .  I have to test that to be satisfied that is the case .
 	I'll report back soon on the PS & please look into this .  There is no 
reason for the driver to keep a system in loop over a failing drive set .
 		Tia ,  JimL

(*)
ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.21-rc4/2.6.21-rc4-mm1/broken-out/mpt-fusion-handle-pci-layer-error-on-resume.patch
ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.21-rc4/2.6.21-rc4-mm1/broken-out/mpt-fusion-handle-mpt_resume-failure-while-resuming.patch

On Mon, 19 Mar 2007, Moore, Eric wrote:
> On Saturday, March 17, 2007 2:33 PM,  James W. Laferriere wrote:
>>  	Hello All ,  I am have been having this problem since I
>> purchased the
>> controller and after changing out the disks I thought were
>> the problem .
>>  	I am still getting the continous :
>>
>> mptscsih: ioc1: attempting task abort! (sc=f7a64500)
>> scsi 3:0:4:0:
>>          command: Inquiry: 12 00 00 00 60 00
>> mptbase: Initiating ioc1 recovery
>> mptscsih: ioc1: task abort: SUCCESS (sc=f7a64500)
>>   target3:0:4: Domain Validation detected failure, dropping back
>>   target3:0:4: Domain Validation skipping write tests
>>   target3:0:4: Ending Domain Validation
>>   target3:0:4: asynchronous
>>   target3:0:5: Beginning Domain Validation
>> mptscsih: ioc0: attempting target reset! (sc=f7a64380)
>>
>>  	The acutual device id's change and the driver
>> continously resets the
>> busses & starts all over .
>>
>>  	The disks are in a HP DS-SL13R-BA 4354R 14drive ultra3
>> racKmount cabinet
>> w/ dualbus & dualps ,  Which seems to present a ID6 ,  That
>> does not show up in
>> any of the bus scans .
>>
>>  	Now I have previously had the same cabinet with 18gb
>> disks which had the
>> same problem with this controller .  BUT I also have a LSI
>> Logic / Symbios
>> Logic 53c1010 66MHz Ultra3 dual SCSI bus Adapter which works
>> flawlessly with the
>> 18gb disks in this very same cabinet .
>>  	The cables for connecting the adapter(s) to tha cabinet
>> are less than 24
>> inches in length .
>>
>>  	Would anyone please shed some light on what it is I am
>> doing wrong or
>> need to do or ....?  Too have this controller recognise these
>> disk drives in
>> this cabinet .
>
> There is a seperate mailing list for scsi releated issues, e.g.
> linux-scsi@.   I've posted a patch to address your issue several times,
> however it seems its not been picked up by the scsi subsystem
> maintainer.   The last time it was posted was here:
> http://marc.info/?l=linux-scsi&m=117089244809072&w=2   An alternative is
> you could obtain our latest drivers from the LSI download site, where
> these drivers should have this patch
> http://www.lsilogic.com/cm/DownloadSearch.do.
>
> Eric
>
>

-- 
+-----------------------------------------------------------------+
| James   W.   Laferriere | System   Techniques | Give me VMS     |
| Network        Engineer | 663  Beaumont  Blvd |  Give me Linux  |
| babydr@baby-dragons.com | Pacifica, CA. 94044 |   only  on  AXP |
+-----------------------------------------------------------------+
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/
\
 
 \ /
  Last update: 2007-03-21 07:55    [from the cache]
©2003-2008