lkml.org 
[lkml]   [2007]   [Mar]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH] drivers: PMC MSP71xx LED driver
Date
Hi Marc,

Your patch does not seem to use the Linux LED API (include/linux/leds.h),
which is sometimes pretty unknown, but dramatically ease your work. Maybe it
is a good idea converting it to this API if you find it relevant.

Also consider the ongoing LED-GPIO API which is being written by ARM people :
http://marc.theaimsgroup.com/?l=linux-kernel&m=110873454720555&w=2

My 2 cents

Le lundi 12 mars 2007, Marc St-Jean a écrit :
> [PATCH] drivers: PMC MSP71xx LED driver
>
> Patch to add LED driver for the PMC-Sierra MSP71xx devices.
>
> This patch references some platform support files previously
> submitted to the linux-mips@linux-mips.org list.
>
> Thanks,
> Marc
>
> Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
> ---
> Re-posting patch with recommended changes:
> -Cleanup on style and formatting for comments, macros, etc.
> -Removed unnecessary memset.
> -Removed unnecessary inlines.
> -Moved some driver private data structures from .h to .c.
> -Made use of schedule_timeout_interruptible() call instead
> of multiple calls.
> -Added calls to kthread_should_stop and try_to_freeze().
>
> drivers/i2c/chips/Kconfig | 9
> drivers/i2c/chips/Makefile | 1
> drivers/i2c/chips/pmctwiled.c | 524
> +++++++++++++++++++ include/asm-mips/pmc-sierra/msp71xx/msp_led_macros.h |
> 273 +++++++++ 4 files changed, 807 insertions(+)
>
> diff --git a/drivers/i2c/chips/Kconfig b/drivers/i2c/chips/Kconfig
> index 87ee3ce..3bef46b 100644
> --- a/drivers/i2c/chips/Kconfig
> +++ b/drivers/i2c/chips/Kconfig
> @@ -50,6 +50,15 @@ config SENSORS_PCF8574
> These devices are hard to detect and rarely found on mainstream
> hardware. If unsure, say N.
>
> +config SENSORS_PMCTWILED
> + tristate "PMC Led-over-TWI driver"
> + depends on I2C && PMC_MSP
> + help
> + The new VPE-safe backend driver for all the LEDs on the 7120 platform.
> +
> + While you may build this as a module, it is recommended you build it
> + into the kernel monolithic so all drivers may access it at all times.
> +
> config SENSORS_PCA9539
> tristate "Philips PCA9539 16-bit I/O port"
> depends on I2C && EXPERIMENTAL
> diff --git a/drivers/i2c/chips/Makefile b/drivers/i2c/chips/Makefile
> index 779868e..4e79e27 100644
> --- a/drivers/i2c/chips/Makefile
> +++ b/drivers/i2c/chips/Makefile
> @@ -10,6 +10,7 @@ obj-$(CONFIG_SENSORS_M41T00) += m41t00.o
> obj-$(CONFIG_SENSORS_PCA9539) += pca9539.o
> obj-$(CONFIG_SENSORS_PCF8574) += pcf8574.o
> obj-$(CONFIG_SENSORS_PCF8591) += pcf8591.o
> +obj-$(CONFIG_SENSORS_PMCTWILED) += pmctwiled.o
> obj-$(CONFIG_ISP1301_OMAP) += isp1301_omap.o
> obj-$(CONFIG_TPS65010) += tps65010.o
>
> diff --git a/drivers/i2c/chips/pmctwiled.c b/drivers/i2c/chips/pmctwiled.c
> new file mode 100644
> index 0000000..69845a5
> --- /dev/null
> +++ b/drivers/i2c/chips/pmctwiled.c
> @@ -0,0 +1,524 @@
> +/*
> + * Special LED-over-TWI-PCA9554 driver for the PMC Sierra
> + * Residential Gateway demo board (and potentially others).
> + *
> + * Based on pca9539.c Copyright (C) 2005 Ben Gardner <bgardner@wabtec.com>
> + * Modified by Copyright 2006-2007 PMC-Sierra, Inc.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; version 2 of the License.
> + */
> +
> +#include <linux/module.h>
> +#include <linux/init.h>
> +#include <linux/kthread.h>
> +#include <linux/i2c.h>
> +#include <linux/freezer.h>
> +
> +#include <msp_led_macros.h>
> +
> +/*
> + * The externally available "registers"
> + *
> + * TODO: We must ensure these are in "shared memory" for the other VPE
> + * to access
> + */
> +u32 msp_led_register[MSP_LED_COUNT];
> +
> +#ifdef CONFIG_PMC_MSP7120_GW
> +/*
> + * For each device, which pins will be in "input" mode:
> + * One byte per device:
> + * 0 = Output
> + * 1 = Input
> + */
> +static const u8 msp_led_initial_input_state[] = {
> + /* No outputs on device 0 or 1, these are inputs only */
> + MSP_LED_INPUT_MODE, MSP_LED_INPUT_MODE,
> + /* All outputs on device 2 through 4 */
> + MSP_LED_OUTPUT_MODE, MSP_LED_OUTPUT_MODE, MSP_LED_OUTPUT_MODE,
> +};
> +
> +/*
> + * For each device, which output pins should start on and off:
> + * One byte per device:
> + * 0 = OFF = HI
> + * 1 = ON = Lo
> + */
> +static const u8 msp_led_initial_pin_state[] = {
> + 0, 0, /* No initial state, these are input only */
> + 1 << 1, /* PWR_GREEN LED on, all others off */
> + 0, /* All off */
> + 0, /* All off */
> +};
> +#endif /* CONFIG_PMC_MSP7120_GW */
> +
> +/* Internal polling data */
> +#define POLL_PERIOD msecs_to_jiffies(125) /* Poll at 125ms */
> +
> +static struct i2c_client *pmctwiled_device[MSP_LED_NUM_DEVICES];
> +static struct task_struct *pmctwiled_pollthread;
> +static u32 private_msp_led_register[MSP_LED_COUNT];
> +static u16 current_period;
> +
> +/* Addresses to scan */
> +#define PMCTWILED_BASEADDRESS 0x38
> +
> +static unsigned short normal_i2c[] = {
> + PMCTWILED_BASEADDRESS + 0,
> + PMCTWILED_BASEADDRESS + 1,
> + PMCTWILED_BASEADDRESS + 2,
> + PMCTWILED_BASEADDRESS + 3,
> + PMCTWILED_BASEADDRESS + 4,
> + I2C_CLIENT_END
> +};
> +
> +/* Insmod parameters */
> +I2C_CLIENT_INSMOD_1(pmctwiled);
> +
> +enum pca9554_cmd {
> + PCA9554_INPUT = 0,
> + PCA9554_OUTPUT = 1,
> + PCA9554_INVERT = 2,
> + PCA9554_DIRECTION = 3,
> +};
> +
> +static int pmctwiled_attach_adapter(struct i2c_adapter *adapter);
> +static int pmctwiled_detect(struct i2c_adapter *adapter,
> + int address, int kind);
> +static int pmctwiled_detach_client(struct i2c_client *client);
> +
> +/* This is the driver that will be inserted */
> +static struct i2c_driver pmctwiled_driver = {
> + .driver = {
> + .name = "pmctwiled",
> + },
> + .attach_adapter = pmctwiled_attach_adapter,
> + .detach_client = pmctwiled_detach_client,
> +};
> +
> +struct pmctwiled_data {
> + struct i2c_client client;
> +};
> +
> +static int pmctwiled_attach_adapter(struct i2c_adapter *adapter)
> +{
> + return i2c_probe(adapter, &addr_data, pmctwiled_detect);
> +}
> +
> +/* This function is called by i2c_probe */
> +static int pmctwiled_detect(struct i2c_adapter *adapter,
> + int address, int kind)
> +{
> + struct i2c_client *new_client = NULL; /* client structure */
> + struct pmctwiled_data *data = NULL; /* local data structure */
> + int err = 0;
> + int dev_id = address - PMCTWILED_BASEADDRESS;
> +
> + if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
> + goto exit;
> +
> + /*
> + * For now, we presume we have a valid client. We now create the
> + * client structure, even though we cannot fill it completely yet.
> + */
> + data = kzalloc(sizeof(*data), GFP_KERNEL);
> + if (!data) {
> + err = -ENOMEM;
> + goto exit;
> + }
> +
> + new_client = &data->client;
> + i2c_set_clientdata(new_client, data);
> + new_client->addr = address;
> + new_client->adapter = adapter;
> + new_client->driver = &pmctwiled_driver;
> + new_client->flags = 0;
> +
> + /*
> + * Detection:
> + * The pca9554 only has 4 registers (0-3).
> + * All other reads should fail.
> + */
> + if (i2c_smbus_read_byte_data(new_client, 3) < 0 ||
> + i2c_smbus_read_byte_data(new_client, 4) >= 0)
> + goto exit_kfree;
> +
> + /* Found PCA9554 (probably) */
> + strlcpy(new_client->name, "pca9554", I2C_NAME_SIZE);
> + printk(KERN_WARNING
> + "Detected PCA9554 I/O chip (device %d) at 0x%02x\n",
> + dev_id, address);
> +
> + /* Tell the I2C layer a new client has arrived */
> + err = i2c_attach_client(new_client);
> + if (err)
> + goto exit_kfree;
> +
> + /*
> + * Register this in the list of available devices, and set up the
> + * initial state
> + */
> + i2c_smbus_write_byte_data(new_client, PCA9554_OUTPUT,
> + i2c_smbus_read_byte_data(new_client, PCA9554_INPUT));
> + i2c_smbus_write_byte_data(new_client, PCA9554_DIRECTION,
> + msp_led_initial_input_state[dev_id]);
> + pmctwiled_device[dev_id] = new_client;
> +
> + return 0;
> +
> +exit_kfree:
> + kfree(data);
> +exit:
> + return err;
> +}
> +
> +static int pmctwiled_detach_client(struct i2c_client *client)
> +{
> + int err;
> + int dev_id = client->addr - PMCTWILED_BASEADDRESS;
> +
> + /* Clear reference so poll thread doesn't use while detaching */
> + pmctwiled_device[dev_id] = NULL;
> +
> + /* Remove this device from the list of devices */
> + err = i2c_detach_client(client);
> + if (err)
> + return err;
> +
> + kfree(i2c_get_clientdata(client));
> +
> + return 0;
> +}
> +
> +/*
> + * mode_bits_update - Sets the mode bits of the given led register
> + * @led_reg_ptr: Pointer to the led register value that needs to be
> updated + * with the given mode.
> + * @mode: new mode value to be set to the register
> + *
> + * Sets the given mode value to the given led register.
> + */
> +inline void mode_bits_update(u32 *led_reg_ptr, enum msp_led_mode mode)
> +{
> + /* TODO: validate mode */
> + *led_reg_ptr |= MSP_LED_MODE_MASK;
> + *led_reg_ptr &= (~((u32) MSP_LED_MODE_MASK) | mode);
> +}
> +
> +/*
> + * sync_led_timer_with_polling_count - Synchronizes the led timer with
> + * polling thread count
> + * @led_id: Index for the private led register used to obtain timer
> + * information
> + * @led_reg_ptr: Pointer to the new led register value
> + *
> + * returns 0: If led is in its final period
> + * returns 1: If led is in its initial period
> + *
> + * This function determines if the led timer is in its initial period or
> + * the final, relative to the TWI-polling thread count (current_period)
> + * and updates the previous timer value in the private led register. If
> + * the state of the led needs to be turned off (i.e. when the led has
> + * timed out) then the mode bits in the current led register pointer is
> + * set to MSP_LED_OFF and the other data bits are set to 0.
> + */
> +int sync_led_timer_with_polling_count(int led_id, u32 *led_reg_ptr)
> +{
> + /* Timer variables */
> + int is_in_initial_period = 0;
> + u8 timer, led_timeout, initial_period, final_period;
> + u16 total_period;
> +
> + /*
> + * Determine the progress into the current cycle, relative to
> + * the POLL_PERIOD
> + */
> + initial_period = *led_reg_ptr >> MSP_LED_INITIALPERIOD_SHIFT;
> + final_period = *led_reg_ptr >> MSP_LED_FINALPERIOD_SHIFT;
> + led_timeout = *led_reg_ptr >> MSP_LED_WATCHDOG_SHIFT;
> + timer = private_msp_led_register[led_id] >> MSP_LED_WATCHDOG_SHIFT;
> +
> + total_period = initial_period + final_period;
> + if (total_period != 0)
> + is_in_initial_period = (current_period % total_period) <
> + initial_period;
> +
> + /*
> + * if the led_timeout is set, adjust the current state to be either
> + * ON or OFF
> + */
> + if (led_timeout > 0) {
> + if (timer >= led_timeout) {
> + /* set the register to OFF state */
> + mode_bits_update(led_reg_ptr, MSP_LED_OFF);
> + timer = 0;
> +
> + /*
> + * TODO:
> + * This introduces a race condition with other
> + * thread using shared memory and must be fixed.
> + */
> + msp_led_turn_off(led_id);
> + } else
> + timer += 1;
> +
> + /* update timer */
> + *led_reg_ptr &= ~(0xff << MSP_LED_WATCHDOG_SHIFT);
> + *led_reg_ptr |= (timer << MSP_LED_WATCHDOG_SHIFT);
> + }
> +
> + return is_in_initial_period;
> +}
> +
> +/*
> + * led_update - Sets the mode bits of the given led register
> + * @led_id - id pertaining to the led that needs update
> + * @prev_direction_bits_ptr - points to the previous direction bits on the
> bus + * @prev_data_bits_ptr - points to the previous data bits on the bus +
> * @curr_direction_bits_ptr - points to the new direction bits for bus
> update + * @curr_data_bits_ptr - points to the new data bits for bus update
> + *
> + * returns 1 - led is in output mode
> + * 0 - led is in input mode and hasn't been updated
> + *
> + * Sets the given mode value to the given led register.
> + */
> +int led_update(int led_id,
> + u8 *prev_direction_bits_ptr, u8 *prev_data_bits_ptr,
> + u8 *curr_direction_bits_ptr, u8 *curr_data_bits_ptr)
> +{
> + u32 curr_led_reg;
> + enum msp_led_mode curr_mode, prev_mode;
> + enum msp_led_direction curr_direction, prev_direction;
> + int is_in_initial_period;
> +
> + /* Read the shared memory into a temporary variable */
> + int pin = led_id % MSP_LED_NUM_DEVICE_PINS;
> + curr_led_reg = msp_led_register[led_id];
> +
> + /* Check if the input direction has changed to output */
> + prev_direction = (enum msp_led_direction)
> + ((private_msp_led_register[led_id] &
> + MSP_LED_DIRECTION_MASK) >> MSP_LED_DIRECTION_SHIFT);
> + curr_direction = (enum msp_led_direction)((curr_led_reg &
> + MSP_LED_DIRECTION_MASK) >> MSP_LED_DIRECTION_SHIFT);
> + if ((prev_direction == MSP_LED_INPUT) &&
> + (curr_direction != MSP_LED_OUTPUT))
> + return 0;
> +
> + /* get the previous mode of the LED */
> + prev_mode = (enum msp_led_mode)(private_msp_led_register[led_id] &
> + MSP_LED_MODE_MASK);
> +
> + if (prev_mode == MSP_LED_ON)
> + *prev_data_bits_ptr |= 1 << pin;
> +
> + if (prev_direction == MSP_LED_INPUT)
> + *prev_direction_bits_ptr |= 1 << pin;
> +
> + /* Update timer and obtain the current period */
> + is_in_initial_period = sync_led_timer_with_polling_count(
> + led_id, &curr_led_reg);
> +
> + /* get the current mode of the LED */
> + curr_mode = (enum msp_led_mode)(curr_led_reg & MSP_LED_MODE_MASK);
> +
> + switch (curr_mode) {
> + case MSP_LED_BLINK:
> + if (is_in_initial_period) {
> + *curr_data_bits_ptr |= 1 << pin;
> + mode_bits_update(&curr_led_reg, MSP_LED_ON);
> + } else
> + mode_bits_update(&curr_led_reg,MSP_LED_OFF);
> + break;
> + case MSP_LED_BLINK_INVERT:
> + if (!is_in_initial_period) {
> + *curr_data_bits_ptr |= 1 << pin;
> + mode_bits_update(&curr_led_reg, MSP_LED_ON);
> + } else
> + mode_bits_update(&curr_led_reg,MSP_LED_OFF);
> + break;
> + case MSP_LED_OFF:
> + /*
> + * Assuming that the led be turned off when set to
> + * output mode
> + */
> + break;
> + case MSP_LED_ON:
> + *curr_data_bits_ptr |= 1 << pin;
> + break;
> + }
> +
> + if (curr_direction == MSP_LED_INPUT)
> + *curr_direction_bits_ptr |= 1 << pin;
> +
> + /* save the current mode */
> + private_msp_led_register[led_id] = curr_led_reg;
> +
> + return 1;
> +}
> +
> +/*
> + * device_update - Updates led device(s) on GPIO
> + * @dev_id - id pertaining to the device that needs update
> + *
> + * returns 1 - device exists
> + * 0 - device does not exist
> + *
> + * Every pin connected to the GPIO is updated if the state of the pin has
> + * changed from its previous value stored in the memory register. A
> temporary + * variable, curr_led_reg is used to store the current value of
> the register + * corresponding to the pin under focus. curLedReg gets its
> value from the + * global shared memory registers for leds. This value is
> compared with the + * previous value to determine if a change to the led
> pin is required. The + * previous values are stored in the private led
> register,
> + * private_msp_led_register.
> + */
> +int device_update(int dev_id)
> +{
> + int pin;
> + u8 curr_direction_bits = 0;
> + u8 curr_data_bits = 0;
> + u8 prev_data_bits = 0;
> + u8 prev_direction_bits = 0;
> +
> + /* if the device wasn't detected */
> + if (pmctwiled_device[dev_id] == NULL)
> + return 0;
> +
> + /* iterate through each pin of the device and update as necessary */
> + for (pin = 0; pin < MSP_LED_NUM_DEVICE_PINS; pin++) {
> + int led_id = MSP_LED_DEVPIN(dev_id, pin);
> + led_update(led_id, &prev_direction_bits, &prev_data_bits,
> + &curr_direction_bits, &curr_data_bits);
> + }
> +
> + /*
> + * BUS OPERATIONS: if the previous state is different from the
> + * current state
> + */
> + if (curr_data_bits != prev_data_bits)
> + i2c_smbus_write_byte_data(pmctwiled_device[dev_id],
> + PCA9554_OUTPUT, ~(curr_data_bits));
> +
> + if (curr_direction_bits != prev_direction_bits)
> + i2c_smbus_write_byte_data(pmctwiled_device[dev_id],
> + PCA9554_DIRECTION, curr_direction_bits);
> +
> + return 1;
> +}
> +
> +static int pmctwiled_poll(void *data)
> +{
> + current_period = 0;
> +
> + /* start the polling loop */
> + do {
> + /* Starting Time */
> + unsigned long poll_end;
> + unsigned long time_left;
> + unsigned int poll_start = jiffies;
> +
> + /* update every device in here for the current period */
> + int dev_id;
> + for (dev_id = 0; dev_id < MSP_LED_NUM_DEVICES; dev_id++)
> + device_update(dev_id);
> +
> + /* Ending Time */
> + poll_end = jiffies;
> + if (poll_end >= poll_start) {
> + time_left = POLL_PERIOD - (poll_end - poll_start);
> + } else {
> + time_left = POLL_PERIOD - ((0xffffffff - poll_start) +
> + poll_end);
> + printk(KERN_WARNING
> + "Warning: Delaying for %lu jiffies. This may "
> + "not be correct because of clock wrapping\n",
> + time_left);
> + }
> + if (time_left > POLL_PERIOD) {
> + printk(KERN_WARNING
> + "Warning: Delay of %lu jiffies requested, "
> + "defaulting back to %lu\n",
> + time_left, POLL_PERIOD);
> + time_left = POLL_PERIOD;
> + }
> +
> + /* reshedule next polling interval */
> + schedule_timeout_interruptible(time_left);
> +
> + /* make swsusp happy with our thread */
> + try_to_freeze();
> +
> + current_period++;
> + } while (!kthread_should_stop());
> +
> + return 0;
> +}
> +
> +void __init pmctwiled_setup(void)
> +{
> + static int called;
> + int dev;
> +
> + /* check if already initialized from platform initialization */
> + if (called)
> + return;
> +
> + /* initialize LEDs to default state */
> + for (dev = 0; dev < MSP_LED_NUM_DEVICES; dev++) {
> + int pin;
> + pmctwiled_device[dev] = NULL;
> +
> + for (pin = 0; pin < 8; pin++) {
> + int led = MSP_LED_DEVPIN(dev, pin);
> + if (msp_led_initial_input_state[dev] & (1 << pin)) {
> + msp_led_disable(led);
> + } else {
> + msp_led_enable(led);
> + if (msp_led_initial_pin_state[dev] & (1 << pin))
> + msp_led_turn_on(led);
> + else
> + msp_led_turn_off(led);
> + }
> +
> + /* Initialize the private led register memory */
> + private_msp_led_register[led] = 0;
> + }
> + }
> +
> + /* indicate initialised */
> + called++;
> +}
> +
> +static int __init pmctwiled_init(void)
> +{
> + /* setup twi led interface */
> + pmctwiled_setup();
> +
> + /* start the polling thread */
> + pmctwiled_pollthread = kthread_run(pmctwiled_poll, NULL,
> + "PMCTwiLedPoller");
> + if (pmctwiled_pollthread == NULL) {
> + printk(KERN_ERR "Could not start polling thread\n");
> + return -ENOMEM;
> + }
> +
> + return i2c_add_driver(&pmctwiled_driver);
> +}
> +
> +static void __exit pmctwiled_exit(void)
> +{
> + /* stop the polling thread */
> + kthread_stop(pmctwiled_pollthread);
> +
> + i2c_del_driver(&pmctwiled_driver);
> +}
> +
> +MODULE_DESCRIPTION("PMC TWI-LED driver");
> +MODULE_LICENSE("GPL");
> +
> +module_init(pmctwiled_init);
> +module_exit(pmctwiled_exit);
> diff --git a/include/asm-mips/pmc-sierra/msp71xx/msp_led_macros.h
> b/include/asm-mips/pmc-sierra/msp71xx/msp_led_macros.h new file mode 100644
> index 0000000..b5fb683
> --- /dev/null
> +++ b/include/asm-mips/pmc-sierra/msp71xx/msp_led_macros.h
> @@ -0,0 +1,273 @@
> +/*
> + * Macros for external SMP-safe access to the PMC MSP7120
> + * Residential Gateway demo board LEDs (over TWI)
> + *
> + * Copyright 2006-2007 PMC-Sierra, Inc.
> + *
> + * This program is free software; you can redistribute it and/or modify
> it + * under the terms of the GNU General Public License as published
> by the + * Free Software Foundation; either version 2 of the License, or
> (at your + * option) any later version.
> + *
> + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
> + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
> OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
> DISCLAIMED. IN + * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY
> DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
> DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
> GOODS OR SERVICES; LOSS OF + * USE, DATA, OR PROFITS; OR BUSINESS
> INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER
> IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR
> OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF + * THIS SOFTWARE, EVEN IF
> ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + *
> + * You should have received a copy of the GNU General Public License
> along + * with this program; if not, write to the Free Software
> Foundation, Inc., + * 675 Mass Ave, Cambridge, MA 02139, USA.
> + */
> +
> +#ifndef __MSP_LED_MACROS_H__
> +#define __MSP_LED_MACROS_H__
> +
> +/* For ll/sc macros */
> +#include <asm/regops.h>
> +
> +/* Generic macros for board setup */
> +#define MSP_LED_DEVPIN(DEVICE, PIN) ((DEVICE * 8) + PIN)
> +
> +/* ----- Per-board configuration ----- */
> +
> +/* TODO: Maybe break this out into one file per board? */
> +
> +#ifdef CONFIG_PMC_MSP7120_GW
> +/* Specific LEDs and PINs which can be controlled on the RG demo board: */
> +#define MSP_LED_PWRSTANDBY_RED MSP_LED_DEVPIN(2, 0)
> +#define MSP_LED_PWRSTANDBY_GREEN MSP_LED_DEVPIN(2, 1)
> +#define MSP_LED_LAN1_10 MSP_LED_DEVPIN(2, 2)
> +#define MSP_LED_LAN1_100 MSP_LED_DEVPIN(2, 3)
> +#define MSP_LED_LAN2_10 MSP_LED_DEVPIN(2, 4)
> +#define MSP_LED_LAN2_100 MSP_LED_DEVPIN(2, 5)
> +#define MSP_LED_LAN3_10 MSP_LED_DEVPIN(2, 6)
> +#define MSP_LED_LAN3_100 MSP_LED_DEVPIN(2, 7)
> +#define MSP_LED_LAN4_10 MSP_LED_DEVPIN(3, 0)
> +#define MSP_LED_LAN4_100 MSP_LED_DEVPIN(3, 1)
> +#define MSP_LED_LAN5_10 MSP_LED_DEVPIN(3, 2)
> +#define MSP_LED_LAN5_100 MSP_LED_DEVPIN(3, 3)
> +#define MSP_LED_RFU_10 MSP_LED_LAN5_10
> +#define MSP_LED_RFU_100 MSP_LED_LAN5_100
> +#define MSP_PIN_FLASH_RESETB MSP_LED_DEVPIN(3, 4)
> +#define MSP_LED_PSTN MSP_LED_DEVPIN(3, 5)
> +#define MSP_PIN_FLASH_BANK MSP_LED_DEVPIN(3, 6)
> +#define MSP_PIN_USB_HOST_DEV MSP_LED_DEVPIN(3, 7)
> +#define MSP_LED_PHONE1 MSP_LED_DEVPIN(4, 0)
> +#define MSP_LED_PHONE2 MSP_LED_DEVPIN(4, 1)
> +#define MSP_LED_USB MSP_LED_DEVPIN(4, 2)
> +#define MSP_LED_WIRELESS MSP_LED_DEVPIN(4, 3)
> +#define MSP_LED_DSL_RED MSP_LED_DEVPIN(4, 4)
> +#define MSP_LED_DSL_GREEN MSP_LED_DEVPIN(4, 5)
> +#define MSP_LED_INTERNET_RED MSP_LED_DEVPIN(4, 6)
> +#define MSP_LED_INTERNET_GREEN MSP_LED_DEVPIN(4, 7)
> +
> +#define MSP_LED_NUM_DEVICES 5
> +#define MSP_LED_NUM_DEVICE_PINS 8
> +#define MSP_LED_COUNT (MSP_LED_NUM_DEVICE_PINS * \
> + MSP_LED_NUM_DEVICES)
> +#define MSP_LED_INPUT_MODE 0xff
> +#define MSP_LED_OUTPUT_MODE 0x00
> +#endif /* CONFIG_PMC_MSP7120_GW */
> +
> +/* ----- End of Per-board configuration ----- */
> +
> +/* Definitions for LED blink rate value */
> +#define MSP_LED_RATE_MAX 0xff
> +
> +/* -- The actual LED register list -- */
> +extern u32 msp_led_register[];
> +
> +/*
> + * Each 'register' has the following format:
> + *
> + * +-------+-----------------------------+
> + * | BITS | DESCRIPTION |
> + * +-------+-----------------------------+
> + * | 31:24 | Watchdog timer |
> + * | | Set to non-zero to start |
> + * | | or to kick, this number |
> + * | | will be decremented every |
> + * | | 125ms, if it reaches zero |
> + * | | the LED will be turned off|
> + * +-------+-----------------------------+
> + * | 23:16 | Initial Period |
> + * | | 125ms increments |
> + * +-------+-----------------------------+
> + * | 15:8 | Final Period |
> + * | | 125ms increments |
> + * +-------+-----------------------------+
> + * | 7:7 | Direction |
> + * | | See msp_led_direction |
> + * +-------+-----------------------------+
> + * | 6:0 | Mode |
> + * | | See msp_led_mode |
> + * +-------+-----------------------------+
> + *
> + * NOTE: You should probably not affect these registers directly but use
> + * the macros in this file. That said, if you need to touch them, be sure
> + * to use ll/sc instructions (or the macros in regops.h) so that values
> are + * preserved safely.
> + */
> +
> +/* Direction modes */
> +enum msp_led_direction {
> + MSP_LED_INPUT = 0,
> + MSP_LED_OUTPUT,
> +};
> +
> +/* Output modes */
> +enum msp_led_mode {
> + MSP_LED_OFF = 0,/* Off steady */
> + MSP_LED_ON, /* On steady */
> + MSP_LED_BLINK, /* On for initial_period, off for final_period */
> + MSP_LED_BLINK_INVERT,
> + /* Off for initial_period, on for final_period */
> +};
> +
> +#define MSP_LED_MODE_MASK 0x7f
> +#define MSP_LED_DIRECTION_MASK 0x80
> +#define MSP_LED_DIRECTION_SHIFT 7
> +#define MSP_LED_INITIALPERIOD_SHIFT 8
> +#define MSP_LED_FINALPERIOD_SHIFT 16
> +#define MSP_LED_WATCHDOG_SHIFT 24
> +
> +/* -- Public API functions -- */
> +
> +/* Low-level macro, explicitly sets the specified LED with the values */
> +static inline void msp_led_set_mode(u16 led,
> + enum msp_led_mode mode, u8 initial_period,
> + u8 final_period, u8 watchdog_timeout)
> +{
> + set_value_reg32(&msp_led_register[led],
> + 0xffffff7f,
> + watchdog_timeout << MSP_LED_WATCHDOG_SHIFT |
> + initial_period << MSP_LED_INITIALPERIOD_SHIFT |
> + final_period << MSP_LED_FINALPERIOD_SHIFT |
> + ((u8)mode & MSP_LED_MODE_MASK));
> +}
> +
> +static inline void msp_led_set_direction(u16 led,
> + enum msp_led_direction direction)
> +{
> + set_value_reg32(&msp_led_register[led],
> + 0x00000080,
> + ((u8)direction << MSP_LED_DIRECTION_SHIFT));
> +}
> +
> +/* Turns the LED on */
> +static inline void msp_led_turn_on(u16 led)
> +{
> + msp_led_set_mode(led, MSP_LED_ON, 0, 0, 0);
> +}
> +
> +/* Set pin LO */
> +static inline void msp_led_pin_lo(u16 pin)
> +{
> + msp_led_set_mode(pin, MSP_LED_ON, 0, 0, 0);
> +}
> +
> +/* Turns the LED off */
> +static inline void msp_led_turn_off(u16 led)
> +{
> + msp_led_set_mode(led, MSP_LED_OFF, 0, 0, 0);
> +}
> +
> +/* Set pin HI */
> +static inline void msp_led_pin_hi(u16 pin)
> +{
> + msp_led_set_mode(pin, MSP_LED_OFF, 0, 0, 0);
> +}
> +
> +/*
> + * Blinks a single LED
> + * Period is specified in 125ms chunks
> + */
> +static inline void msp_led_blink(u16 led, u8 initial_period, u8
> final_period) +{
> + msp_led_set_mode(led, MSP_LED_BLINK, initial_period,
> + final_period, 0);
> +}
> +
> +static inline void msp_led_blink_2Hz(u16 led)
> +{
> + msp_led_set_mode(led, MSP_LED_BLINK, 2, 2, 0);
> +}
> +
> +static inline void msp_led_blink_4Hz(u16 led)
> +{
> + msp_led_set_mode(led, MSP_LED_BLINK, 1, 1, 0);
> +}
> +
> +/*
> + * Blinks one LED, then the other
> + * Period is specified in 125ms chunks
> + */
> +static inline void msp_led_alternate(u16 led1, u16 led2,
> + u8 led1_period, u8 led2_period)
> +{
> + msp_led_set_mode(led1, MSP_LED_BLINK, led1_period,
> + led2_period, 0);
> + msp_led_set_mode(led2, MSP_LED_BLINK_INVERT, led1_period,
> + led2_period, 0);
> +}
> +
> +/*
> + * Stops both alternating LEDs from blinking, leaving 'on_led' on
> + * and 'off_led' off.
> + */
> +static inline void msp_led_alternate_stop(u16 on_led, u16 off_led)
> +{
> + msp_led_turn_on(on_led);
> + msp_led_turn_off(off_led);
> +}
> +
> +/*
> + * Starts the LED blinking at the specified rate until the
> watchdog_timeout + * (specified in 125ms increments) expires, when the LED
> is turned off. + *
> + * This can also be used to kick the watchdog.
> + *
> + * Calling any other 'msp_led_...' macro will disable the watchdog,
> + * as will kicking this watchdog with a watchdogtimeout value of 0.
> + * When the watchdog is disabled, the LED will blink forever.
> + */
> +static inline void msp_led_watchdog_init(u16 led, u8 initial_period,
> + u8 final_period, u8 watchdog_timeout)
> +{
> + msp_led_set_mode(led, MSP_LED_BLINK, initial_period,
> + final_period, watchdog_timeout);
> +}
> +
> +/*
> + * Kicks a 'watchdog' LED. If the LED is already blinking or on,
> + * it will start the watchdog countdown. If the LED is already off or
> + * the wathdog timeout given is 0, it will ensure the LED is off and
> + * the watchdog timer has stopped.
> + */
> +static inline void msp_led_watchdog_kick(u16 led, u8 watchdog_timeout)
> +{
> + set_value_reg32(&msp_led_register[led],
> + 0xff << MSP_LED_WATCHDOG_SHIFT,
> + watchdog_timeout << MSP_LED_WATCHDOG_SHIFT);
> +}
> +
> +/*
> + * Set the direction of the led pins.
> + */
> +static inline void msp_led_enable(u16 led)
> +{
> + msp_led_set_direction(led, MSP_LED_OUTPUT);
> +}
> +
> +static inline void msp_led_disable(u16 led)
> +{
> + msp_led_set_direction(led, MSP_LED_INPUT);
> +}
> +
> +#endif /* !__MSP_LED_MACROS_H__ */



--
Cordialement, Florian Fainelli
---------------------------------------------
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2007-03-13 10:07    [W:0.062 / U:0.184 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site