lkml.org 
[lkml]   [2007]   [Feb]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH] [NET] dmfe : number of fixes and features
From: Maxim Levitsky <maximlevitsky@yahoo.com>
Subject: [PATCH] [NET] [003] dmfe : fix link detection

Cleanup link detection
Fix link not detected when using external PHY

Signed-off-by: Maxim Levitsky <maximlevitsky@yahoo.com>

---

CR12's bits 0 and 1 show link status/speed only for internal PHY.
In case external one is used, only bit 6 shows link status via special line , and can be left
unnconected
Thus we need to check bit 6 and also query PHY for link status
Note: internal phy is standard phy , so will indicate link status too.

--- linux-2.6.20-mod/drivers/net/tulip/dmfe.c 2007-02-07 18:40:33.000000000 +0200
+++ linux-2.6.20-test/drivers/net/tulip/dmfe.c 2007-02-07 18:44:01.000000000 +0200
@@ -147,7 +147,7 @@
printk(KERN_ERR DRV_NAME ": %s %lx\n", (msg), (long) (value))

#define SHOW_MEDIA_TYPE(mode) \
- printk(KERN_ERR DRV_NAME ": \
+ printk(KERN_INFO DRV_NAME ": \
Change Speed to %sMhz %s duplex\n",mode & 1 ?"100":"10", \
mode & 4 ? "full":"half");

@@ -242,7 +242,6 @@ struct dmfe_board_info {
u8 media_mode; /* user specify media mode */
u8 op_mode; /* real work media mode */
u8 phy_addr;
- u8 link_failed; /* Ever link failed */
u8 wait_reset; /* Hardware failed, need to reset */
u8 dm910x_chk_mode; /* Operating mode check */
u8 first_in_callback; /* Flag to record state */
@@ -536,7 +535,6 @@ static int dmfe_open(struct DEVICE *dev)
db->tx_packet_cnt = 0;
db->tx_queue_cnt = 0;
db->rx_avail_cnt = 0;
- db->link_failed = 1;
db->wait_reset = 0;

db->first_in_callback = 0;
@@ -1091,6 +1089,8 @@ static void dmfe_timer(unsigned long dat
struct dmfe_board_info *db = netdev_priv(dev);
unsigned long flags;

+ int link_ok, link_ok_phy;
+
DMFE_DBUG(0, "dmfe_timer()", 0);
spin_lock_irqsave(&db->lock, flags);

@@ -1155,22 +1155,45 @@ static void dmfe_timer(unsigned long dat
else
tmp_cr12 = inb(db->ioaddr + DCR12); /* DM9102/DM9102A */

+
if ( ((db->chip_id == PCI_DM9102_ID) &&
(db->chip_revision == 0x02000030)) ||
((db->chip_id == PCI_DM9132_ID) &&
(db->chip_revision == 0x02000010)) ) {
/* DM9102A Chip */
if (tmp_cr12 & 2)
- tmp_cr12 = 0x0; /* Link failed */
+ link_ok = 0;
else
- tmp_cr12 = 0x3; /* Link OK */
+ link_ok = 1;
+ }
+ else
+ /*0x43 is used instead of 0x3 because bit 6 should be
+ connected to external PHY and specify its link status.*/
+ link_ok = (tmp_cr12 & 0x43) ? 1 : 0;
+
+
+ /* If chip reports that link is failed it could be because external
+ PHY is not conected correctly to chip (through pin 89).
+ To be sure ask PHY too.
+ */
+
+ /* need a dummy read because of PHY's register latch*/
+ phy_read (db->ioaddr, db->phy_addr, 1, db->chip_id);
+ link_ok_phy = (phy_read (db->ioaddr,
+ db->phy_addr, 1, db->chip_id) & 0x4) ? 1 : 0;
+
+
+
+ if (link_ok_phy != link_ok) {
+ DMFE_DBUG (0, "PHY and chip report different link status", 0);
+ link_ok = link_ok | link_ok_phy;
}

- if ( !(tmp_cr12 & 0x3) && !db->link_failed ) {
+ if ( !link_ok && netif_carrier_ok(dev) ) {
/* Link Failed */
DMFE_DBUG(0, "Link Failed", tmp_cr12);
- db->link_failed = 1;
- netif_carrier_off(db->dev);
+
+ netif_carrier_off(dev);

/* For Force 10/100M Half/Full mode: Enable Auto-Nego mode */
/* AUTO or force 1M Homerun/Longrun don't need */
@@ -1184,19 +1207,17 @@ static void dmfe_timer(unsigned long dat
db->cr6_data&=~0x00000200; /* bit9=0, HD mode */
update_cr6(db->cr6_data, db->ioaddr);
}
- } else
- if ((tmp_cr12 & 0x3) && db->link_failed) {
- DMFE_DBUG(0, "Link link OK", tmp_cr12);
- db->link_failed = 0;
+
+ } else if (!netif_carrier_ok(dev)) {
+
+ DMFE_DBUG(0, "Link OK", tmp_cr12);

/* Auto Sense Speed */
- if ( (db->media_mode & DMFE_AUTO) &&
- dmfe_sense_speed(db) )
- db->link_failed = 1;
- else
- netif_carrier_on(db->dev);
+ if (! (db->media_mode & DMFE_AUTO) || !dmfe_sense_speed(db)) {
+ netif_carrier_on(dev);
+ SHOW_MEDIA_TYPE(db->op_mode);
+ }
dmfe_process_mode(db);
- /* SHOW_MEDIA_TYPE(db->op_mode); */
}

/* HPNA remote command check */
@@ -1243,7 +1264,7 @@ static void dmfe_dynamic_reset(struct DE
db->tx_packet_cnt = 0;
db->tx_queue_cnt = 0;
db->rx_avail_cnt = 0;
- db->link_failed = 1;
+ netif_carrier_off(dev);
db->wait_reset = 0;

/* Re-initilize DM910X board */



____________________________________________________________________________________
Any questions? Get answers on any topic at www.Answers.yahoo.com. Try it now.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
\
 
 \ /
  Last update: 2007-02-07 19:03    [W:0.029 / U:0.836 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site