lkml.org 
[lkml]   [2007]   [Feb]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    From
    SubjectRe: PCMCIA WLAN card initialization error
    Date
    Hi,

    I am resending this to the orinoco devel mailing list.

    Today I have tried using a Linksys WPC11 WLAN card and another Senao
    NL2511 Plus and I am seeing the same errors in the kernel log and
    again, the network interface does not show up with iwconfig.

    These two cards are known to be working under windows xp.

    ==== Linksys WPC11 ====
    Feb 19 08:59:30 bonsai pccard: card ejected from slot 0
    Feb 19 08:59:39 bonsai pccard: PCMCIA card inserted into slot 0
    Feb 19 08:59:39 bonsai pcmcia: registering new device pcmcia0.0
    Feb 19 08:59:39 bonsai pcmcia: request for exclusive IRQ could not be fulfilled.
    Feb 19 08:59:39 bonsai pcmcia: the driver needs updating to supported shared IRQ lines.
    Feb 19 08:59:39 bonsai eth2: failed to initialize firmware (err = -19)
    Feb 19 08:59:39 bonsai orinoco_cs: register_netdev() failed
    Feb 19 08:59:39 bonsai pcmcia: request for exclusive IRQ could not be fulfilled.
    Feb 19 08:59:39 bonsai pcmcia: the driver needs updating to supported shared IRQ lines.
    Feb 19 08:59:39 bonsai eth2: failed to initialize firmware (err = -19)
    Feb 19 08:59:39 bonsai orinoco_cs: register_netdev() failed

    ==== SENAO NL2511 Plus ====
    Feb 19 09:01:21 bonsai pccard: card ejected from slot 0
    Feb 19 09:01:40 bonsai pccard: PCMCIA card inserted into slot 0
    Feb 19 09:01:40 bonsai pcmcia: registering new device pcmcia0.0
    Feb 19 09:01:40 bonsai pcmcia: request for exclusive IRQ could not be fulfilled.
    Feb 19 09:01:40 bonsai pcmcia: the driver needs updating to supported shared IRQ lines.
    Feb 19 09:01:40 bonsai eth2: failed to initialize firmware (err = -19)
    Feb 19 09:01:40 bonsai orinoco_cs: register_netdev() failed
    Feb 19 09:01:40 bonsai pcmcia: request for exclusive IRQ could not be fulfilled.
    Feb 19 09:01:40 bonsai pcmcia: the driver needs updating to supported shared IRQ lines.
    Feb 19 09:01:40 bonsai eth2: failed to initialize firmware (err = -19)
    Feb 19 09:01:40 bonsai orinoco_cs: register_netdev() failed
    Feb 19 09:01:56 bonsai pccard: card ejected from slot 0

    Timur


    Timur Aydin <ta@taydin.org> writes:

    > Hi,
    >
    > I have a Prism based PCMCIA WLAN card, which I want to use in my
    > workstation PC. I am using a Ricoh RL5c475 based PCMCIA/PCI bridge to
    > attach the card to one of the empty PCI slots. I want to use this PC
    > as a wireless access point (with hostap), but first I want to make
    > sure the card works, so I first want to use the card as a client to an
    > existing wireless access point. So I compiled support into the linux
    > kernel for only the hermes chipset and the yenta driver (no hostap
    > right now).
    >
    > The problem is that when iwconfig is issued, the wireless interface
    > does not show up.
    >
    > I am seeing some error or warning messages in the kernel logs, but I
    > am not sure if they are relevant to this. For example:
    >
    > ...
    > orinoco 0.15 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al)
    > orinoco_cs 0.15 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al)
    > pcmcia: request for exclusive IRQ could not be fulfilled.
    > pcmcia: the driver needs updating to supported shared IRQ lines.
    > eth2: failed to initialize firmware (err = -19)
    > orinoco_cs: register_netdev() failed
    > pcmcia: request for exclusive IRQ could not be fulfilled.
    > pcmcia: the driver needs updating to supported shared IRQ lines.
    > eth2: failed to initialize firmware (err = -19)
    > orinoco_cs: register_netdev() failed
    > ...
    >
    >
    > I am also seeing resource allocation errors:
    >
    > PCI: Failed to allocate mem resource #10:2000000@f8000000 for 0000:02:08.0
    > PCI: Bus 3, cardbus bridge: 0000:02:08.0
    > IO window: 00009000-000090ff
    > IO window: 00009400-000094ff
    > PREFETCH window: 50000000-51ffffff
    > PCI: Bridge: 0000:00:0e.0
    > IO window: 9000-afff
    > MEM window: f5000000-f6ffffff
    > PREFETCH window: 50000000-52ffffff
    >
    > I am not sure, but I think the actual error is the (err = -19). I have
    > added some extra printk's into hermes.c. This error originates from
    > the hermes_init function in hermes.c:
    >
    > /* Normally it's a "can't happen" for the command register to
    > be busy when we go to issue a command because we are
    > serializing all commands. However we want to have some
    > chance of resetting the card even if it gets into a stupid
    > state, so we actually wait to see if the command register
    > will unbusy itself here. */
    > k = CMD_BUSY_TIMEOUT;
    > reg = hermes_read_regn(hw, CMD);
    > while (k && (reg & HERMES_CMD_BUSY)) {
    > if (reg == 0xffff) /* Special case - the card has probably been removed,
    > so don't wait for the timeout */
    > return -ENODEV;
    >
    > k--;
    > udelay(1);
    > reg = hermes_read_regn(hw, CMD);
    > }
    >
    > reg is indeed 0xffff and the function returns -ENODEV.
    >
    > I need help to further troubleshoot the problem, any directions or
    > hints welcome...
    >
    > Here is the system information:
    >
    > uname -a:
    > Linux bonsai 2.6.19-gentoo-r5 #1 PREEMPT Sun Feb 18 22:04:07 EET 2007
    > i686 AMD Athlon(tm) 64 Processor 3500+ AuthenticAMD GNU/Linux
    >
    > The grub.conf, /etc/pcmcia/config.opts, lspci, lspcmcia and dmesg
    > output is attached.
    > Socket 0 Bridge: [yenta_cardbus] (bus ID: 0000:02:08.0)
    > Configuration: state: on ready: yes
    > Voltage: 3.3V Vcc: 3.3V Vpp: 0.0V
    > Available IRQs: none
    > Available ioports: 0x00000100 - 0x0000028f
    > 0x00000298 - 0x000003af
    > 0x000003e0 - 0x000004cf
    > 0x000004d8 - 0x000004ff
    > 0x00000820 - 0x000008ff
    > 0x00000a00 - 0x00000aff
    > 0x00000c00 - 0x00000cf7
    > 0x00009000 - 0x0000afff
    > Available iomem: 0x000c0000 - 0x000fffff
    > 0x60000000 - 0x60ffffff
    > 0xa0000000 - 0xa0ffffff
    > 0xf5000000 - 0xf5ffffff
    > 0xf6200000 - 0xf6ffffff
    > Socket 0 Device 0: [-- no driver --] (bus ID: 0.0)
    > Configuration: state: on
    > Product Name: INTERSIL HFA384x/IEEE Version 01.02
    > Identification: manf_id: 0x0156 card_id: 0x0002
    > function: 6 (network)
    > prod_id(1): "INTERSIL" (0x74c5e40d)
    > prod_id(2): "HFA384x/IEEE" (0xdb472a18)
    > prod_id(3): "Version 01.02" (0x4b74baa0)
    > prod_id(4): --- (---)
    > 00:00.0 Host bridge: nVidia Corporation nForce3 250Gb Host Bridge (rev a1)
    > Subsystem: Micro-Star International Co., Ltd. Unknown device 0250
    > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    > Latency: 0
    > Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
    > Capabilities: [44] HyperTransport: Slave or Primary Interface
    > Command: BaseUnitID=0 UnitCnt=14 MastHost- DefDir- DUL-
    > Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
    > Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
    > Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
    > Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
    > Revision ID: 1.03
    > Link Frequency 0: 1.0GHz
    > Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
    > Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
    > Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
    > Link Frequency 1: 200MHz
    > Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
    > Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
    > Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
    > Prefetchable memory behind bridge Upper: 00-00
    > Bus Number: 00
    > Capabilities: [c0] AGP version 2.0
    > Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
    > Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=x1
    >
    > 00:01.0 ISA bridge: nVidia Corporation nForce3 250Gb LPC Bridge (rev a2)
    > Subsystem: Micro-Star International Co., Ltd. Unknown device 0250
    > Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    > Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    > Latency: 0
    >
    > 00:01.1 SMBus: nVidia Corporation nForce 250Gb PCI System Management (rev a1)
    > Subsystem: Micro-Star International Co., Ltd. Unknown device 0250
    > Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    > Interrupt: pin A routed to IRQ 10
    > Region 0: I/O ports at cc00 [size=32]
    > Region 4: I/O ports at 4c00 [size=64]
    > Region 5: I/O ports at 4c40 [size=64]
    > Capabilities: [44] Power Management version 2
    > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
    > Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    >
    > 00:02.0 USB Controller: nVidia Corporation CK8S USB Controller (rev a1) (prog-if 10 [OHCI])
    > Subsystem: Micro-Star International Co., Ltd. Unknown device 0250
    > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    > Latency: 0 (750ns min, 250ns max)
    > Interrupt: pin A routed to IRQ 20
    > Region 0: Memory at f7003000 (32-bit, non-prefetchable) [size=4K]
    > Capabilities: [44] Power Management version 2
    > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
    > Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    >
    > 00:02.1 USB Controller: nVidia Corporation CK8S USB Controller (rev a1) (prog-if 10 [OHCI])
    > Subsystem: Micro-Star International Co., Ltd. Unknown device 0250
    > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    > Latency: 0 (750ns min, 250ns max)
    > Interrupt: pin B routed to IRQ 21
    > Region 0: Memory at f7004000 (32-bit, non-prefetchable) [size=4K]
    > Capabilities: [44] Power Management version 2
    > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
    > Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    >
    > 00:02.2 USB Controller: nVidia Corporation nForce3 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI])
    > Subsystem: Micro-Star International Co., Ltd. Unknown device 0250
    > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    > Latency: 0 (750ns min, 250ns max)
    > Interrupt: pin C routed to IRQ 19
    > Region 0: Memory at f7005000 (32-bit, non-prefetchable) [size=256]
    > Capabilities: [44] Debug port
    > Capabilities: [80] Power Management version 2
    > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
    > Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    >
    > 00:05.0 Bridge: nVidia Corporation CK8S Ethernet Controller (rev a2)
    > Subsystem: Micro-Star International Co., Ltd. Unknown device 0250
    > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    > Latency: 0 (250ns min, 5000ns max)
    > Interrupt: pin A routed to IRQ 18
    > Region 0: Memory at f7000000 (32-bit, non-prefetchable) [size=4K]
    > Region 1: I/O ports at b800 [size=8]
    > Capabilities: [44] Power Management version 2
    > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
    > Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
    >
    > 00:06.0 Multimedia audio controller: nVidia Corporation nForce3 250Gb AC'97 Audio Controller (rev a1)
    > Subsystem: Micro-Star International Co., Ltd. Unknown device 7585
    > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    > Latency: 0 (500ns min, 1250ns max)
    > Interrupt: pin A routed to IRQ 18
    > Region 0: I/O ports at bc00 [size=256]
    > Region 1: I/O ports at c000 [size=128]
    > Region 2: Memory at f7001000 (32-bit, non-prefetchable) [size=4K]
    > Capabilities: [44] Power Management version 2
    > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    > Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    >
    > 00:08.0 IDE interface: nVidia Corporation CK8S Parallel ATA Controller (v2.5) (rev a2) (prog-if 8a [Master SecP PriP])
    > Subsystem: Micro-Star International Co., Ltd. Unknown device 0250
    > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    > Latency: 0 (750ns min, 250ns max)
    > Region 4: I/O ports at f000 [size=16]
    > Capabilities: [44] Power Management version 2
    > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    > Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    >
    > 00:0b.0 PCI bridge: nVidia Corporation nForce3 250Gb AGP Host to PCI Bridge (rev a2) (prog-if 00 [Normal decode])
    > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    > Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    > Latency: 16
    > Bus: primary=00, secondary=01, subordinate=01, sec-latency=10
    > I/O behind bridge: 0000f000-00000fff
    > Memory behind bridge: f0000000-f2ffffff
    > Prefetchable memory behind bridge: f3000000-f4ffffff
    > Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
    > BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
    >
    > 00:0e.0 PCI bridge: nVidia Corporation nForce3 250Gb PCI-to-PCI Bridge (rev a2) (prog-if 00 [Normal decode])
    > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    > Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    > Latency: 0
    > Bus: primary=00, secondary=02, subordinate=06, sec-latency=128
    > I/O behind bridge: 00009000-0000afff
    > Memory behind bridge: f5000000-f6ffffff
    > Prefetchable memory behind bridge: 50000000-52ffffff
    > Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
    > BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
    >
    > 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
    > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    > Capabilities: [80] HyperTransport: Host or Secondary Interface
    > !!! Possibly incomplete decoding
    > Command: WarmRst+ DblEnd-
    > Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
    > Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
    > Revision ID: 1.02
    >
    > 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
    > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    >
    > 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
    > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    >
    > 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
    > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    >
    > 01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G550 AGP (rev 01) (prog-if 00 [VGA])
    > Subsystem: Matrox Graphics, Inc. Millennium G550 Dual Head DDR 32Mb
    > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    > Latency: 32 (4000ns min, 8000ns max), Cache Line Size: 32 bytes
    > Interrupt: pin A routed to IRQ 17
    > Region 0: Memory at <ignored> (32-bit, prefetchable)
    > Region 1: Memory at f0000000 (32-bit, non-prefetchable) [size=16K]
    > Region 2: Memory at f1000000 (32-bit, non-prefetchable) [size=8M]
    > [virtual] Expansion ROM at f3000000 [disabled] [size=128K]
    > Capabilities: [dc] Power Management version 2
    > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    > Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    > Capabilities: [f0] AGP version 2.0
    > Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
    > Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x1
    >
    > 02:08.0 CardBus bridge: Ricoh Co Ltd RL5c475 (rev 81)
    > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    > Latency: 168
    > Interrupt: pin A routed to IRQ 16
    > Region 0: Memory at f6005000 (32-bit, non-prefetchable) [size=4K]
    > Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
    > Memory window 0: 50000000-51fff000 (prefetchable)
    > Memory window 1: f6002000-f6003000
    > I/O window 0: 00009000-000090ff
    > I/O window 1: 00009400-000094ff
    > BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
    > 16-bit legacy interface ports at 0001
    >
    > 02:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10)
    > Subsystem: Micro-Star International Co., Ltd. Unknown device 025c
    > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
    > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    > Latency: 32 (8000ns min, 16000ns max), Cache Line Size: 64 bytes
    > Interrupt: pin A routed to IRQ 17
    > Region 0: I/O ports at a000 [size=256]
    > Region 1: Memory at f6004000 (32-bit, non-prefetchable) [size=256]
    > [virtual] Expansion ROM at 52000000 [disabled] [size=128K]
    > Capabilities: [dc] Power Management version 2
    > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
    > Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    >
    > us_irq 14 global_irq 14 high edge)
    > ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
    > ACPI: IRQ9 used by override.
    > ACPI: IRQ14 used by override.
    > ACPI: IRQ15 used by override.
    > Enabling APIC mode: Flat. Using 1 I/O APICs
    > Using ACPI (MADT) for SMP configuration information
    > Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
    > Detected 2210.778 MHz processor.
    > Built 1 zonelists. Total pages: 260081
    > Kernel command line: root=/dev/hda3 pci=assign-busses
    > mapped APIC to ffffd000 (fee00000)
    > mapped IOAPIC to ffffc000 (fec00000)
    > Enabling fast FPU save and restore... done.
    > Enabling unmasked SIMD FPU exception support... done.
    > Initializing CPU#0
    > PID hash table entries: 4096 (order: 12, 16384 bytes)
    > Console: colour VGA+ 80x25
    > Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    > Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    > Memory: 1034304k/1048512k available (2876k kernel code, 13568k reserved, 1189k data, 184k init, 131008k highmem)
    > virtual kernel memory layout:
    > fixmap : 0xfffaa000 - 0xfffff000 ( 340 kB)
    > pkmap : 0xff800000 - 0xffc00000 (4096 kB)
    > vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
    > lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
    > .init : 0xc04fc000 - 0xc052a000 ( 184 kB)
    > .data : 0xc03cf034 - 0xc04f846c (1189 kB)
    > .text : 0xc0100000 - 0xc03cf034 (2876 kB)
    > Checking if this processor honours the WP bit even in supervisor mode... Ok.
    > Calibrating delay using timer specific routine.. 4423.52 BogoMIPS (lpj=22117605)
    > Mount-cache hash table entries: 512
    > CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000000 00000000 00000000
    > CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
    > CPU: L2 Cache: 512K (64 bytes/line)
    > CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000000 00000000 00000000
    > Intel machine check architecture supported.
    > Intel machine check reporting enabled on CPU#0.
    > Compat vDSO mapped to ffffe000.
    > CPU: AMD Athlon(tm) 64 Processor 3500+ stepping 00
    > Checking 'hlt' instruction... OK.
    > ACPI: Core revision 20060707
    > ENABLING IO-APIC IRQs
    > ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
    > NET: Registered protocol family 16
    > ACPI: bus type pci registered
    > PCI: PCI BIOS revision 2.10 entry at 0xfbe50, last bus=3
    > PCI: Using configuration type 1
    > Setting up standard PCI resources
    > ACPI: Interpreter enabled
    > ACPI: Using IOAPIC for interrupt routing
    > ACPI: PCI Root Bridge [PCI0] (0000:00)
    > PCI: Probing PCI hardware (bus 00)
    > Boot video device is 0000:01:00.0
    > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
    > ACPI: Power Resource [ISAV] (on)
    > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
    > ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 6 7 10 11 12 14 15)
    > ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    > ACPI: PCI Interrupt Link [LNK3] (IRQs *3 4 5 6 7 10 11 12 14 15)
    > ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    > ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 10 *11 12 14 15)
    > ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
    > ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
    > ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
    > ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    > ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 *7 10 11 12 14 15)
    > ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    > ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
    > ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 10 *11 12 14 15)
    > ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    > ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    > ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    > ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    > ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    > ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
    > ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
    > ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
    > ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
    > ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
    > ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
    > ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
    > Linux Plug and Play Support v0.97 (c) Adam Belay
    > pnp: PnP ACPI init
    > pnp: PnP ACPI: found 10 devices
    > SCSI subsystem initialized
    > usbcore: registered new interface driver usbfs
    > usbcore: registered new interface driver hub
    > usbcore: registered new device driver usb
    > PCI: Using ACPI for IRQ routing
    > PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
    > PCI: Cannot allocate resource region 0 of device 0000:01:00.0
    > pnp: 00:00: ioport range 0x4000-0x407f could not be reserved
    > pnp: 00:00: ioport range 0x4080-0x40ff has been reserved
    > pnp: 00:00: ioport range 0x4400-0x447f has been reserved
    > pnp: 00:00: ioport range 0x4480-0x44ff could not be reserved
    > pnp: 00:00: ioport range 0x4800-0x487f has been reserved
    > pnp: 00:00: ioport range 0x4880-0x48ff has been reserved
    > PCI: Failed to allocate mem resource #0:2000000@f4000000 for 0000:01:00.0
    > PCI: Bridge: 0000:00:0b.0
    > IO window: disabled.
    > MEM window: f0000000-f2ffffff
    > PREFETCH window: f3000000-f4ffffff
    > PCI: Failed to allocate mem resource #10:2000000@f8000000 for 0000:02:08.0
    > PCI: Bus 3, cardbus bridge: 0000:02:08.0
    > IO window: 00009000-000090ff
    > IO window: 00009400-000094ff
    > PREFETCH window: 50000000-51ffffff
    > PCI: Bridge: 0000:00:0e.0
    > IO window: 9000-afff
    > MEM window: f5000000-f6ffffff
    > PREFETCH window: 50000000-52ffffff
    > PCI: Setting latency timer of device 0000:00:0e.0 to 64
    > ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
    > ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 16
    > NET: Registered protocol family 2
    > IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
    > TCP established hash table entries: 131072 (order: 7, 524288 bytes)
    > TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
    > TCP: Hash tables configured (established 131072 bind 65536)
    > TCP reno registered
    > Machine check exception polling timer started.
    > highmem bounce pool size: 64 pages
    > io scheduler noop registered
    > io scheduler cfq registered (default)
    > lp: driver loaded but no devices found
    > Real Time Clock Driver v1.12ac
    > Non-volatile memory driver v1.2
    > Linux agpgart interface v0.101 (c) Dave Jones
    > agpgart: Detected AGP bridge 0
    > agpgart: Setting up Nforce3 AGP.
    > agpgart: AGP aperture is 128M @ 0xe8000000
    > [drm] Initialized drm 1.0.1 20051102
    > ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
    > ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 17
    > matroxfb: Matrox G550 detected
    > matroxfb: video RAM is not available in PCI address space, matroxfb disabled
    > matroxfb: probe of 0000:01:00.0 failed with error -1
    > Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
    > serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    > 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    > Floppy drive(s): fd0 is 1.44M
    > FDC 0 is a post-1991 82077
    > RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
    > loop: loaded (max 8 devices)
    > e100: Intel(R) PRO/100 Network Driver, 3.5.17-k2-NAPI
    > e100: Copyright(c) 1999-2006 Intel Corporation
    > forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.57.
    > ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
    > ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [APCH] -> GSI 23 (level, high) -> IRQ 18
    > PCI: Setting latency timer of device 0000:00:05.0 to 64
    > eth0: forcedeth.c: subsystem: 01462:0250 bound to 0000:00:05.0
    > r8169 Gigabit Ethernet driver 2.2LK loaded
    > ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16
    > ACPI: PCI Interrupt 0000:02:0d.0[A] -> Link [APC5] -> GSI 16 (level, low) -> IRQ 17
    > eth1: RTL8169s/8110s at 0xf881c000, 00:11:09:cb:83:6b, IRQ 17
    > Linux video capture interface: v2.00
    > saa7130/34: v4l2 driver version 0.2.14 loaded
    > Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    > ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    > NFORCE3-250: IDE controller at PCI slot 0000:00:08.0
    > NFORCE3-250: chipset revision 162
    > NFORCE3-250: not 100% native mode: will probe irqs later
    > NFORCE3-250: BIOS didn't set cable bits correctly. Enabling workaround.
    > NFORCE3-250: 0000:00:08.0 (rev a2) UDMA133 controller
    > ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
    > ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
    > Probing IDE interface ide0...
    > hda: SAMSUNG SP0802N, ATA DISK drive
    > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    > Probing IDE interface ide1...
    > hdc: PHILIPS DVDR824DP, ATAPI CD/DVD-ROM drive
    > ide1 at 0x170-0x177,0x376 on irq 15
    > hda: max request size: 512KiB
    > hda: 156368016 sectors (80060 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
    > hda: cache flushes supported
    > hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
    > hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(33)
    > Uniform CD-ROM driver Revision: 3.20
    > Yenta: CardBus bridge found at 0000:02:08.0 [0000:0000]
    > Yenta: ISA IRQ mask 0x0000, PCI irq 16
    > Socket status: 30000810
    > pcmcia: parent PCI bridge I/O window: 0x9000 - 0xafff
    > cs: IO port probe 0x9000-0xafff: clean.
    > pcmcia: parent PCI bridge Memory window: 0xf5000000 - 0xf6ffffff
    > pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x52ffffff
    > ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
    > ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 22 (level, high) -> IRQ 19
    > PCI: Setting latency timer of device 0000:00:02.2 to 64
    > ehci_hcd 0000:00:02.2: EHCI Host Controller
    > ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
    > ehci_hcd 0000:00:02.2: debug port 1
    > PCI: cache line size of 64 is not supported by device 0000:00:02.2
    > ehci_hcd 0000:00:02.2: irq 19, io mem 0xf7005000
    > ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
    > usb usb1: configuration #1 chosen from 1 choice
    > hub 1-0:1.0: USB hub found
    > hub 1-0:1.0: 8 ports detected
    > ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
    > ACPI: PCI Interrupt Link [APCF] enabled at IRQ 21
    > ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 21 (level, high) -> IRQ 20
    > PCI: Setting latency timer of device 0000:00:02.0 to 64
    > ohci_hcd 0000:00:02.0: OHCI Host Controller
    > ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
    > ohci_hcd 0000:00:02.0: irq 20, io mem 0xf7003000
    > usb usb2: configuration #1 chosen from 1 choice
    > hub 2-0:1.0: USB hub found
    > hub 2-0:1.0: 4 ports detected
    > ACPI: PCI Interrupt Link [APCG] enabled at IRQ 20
    > ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCG] -> GSI 20 (level, high) -> IRQ 21
    > PCI: Setting latency timer of device 0000:00:02.1 to 64
    > ohci_hcd 0000:00:02.1: OHCI Host Controller
    > ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
    > ohci_hcd 0000:00:02.1: irq 21, io mem 0xf7004000
    > usb usb3: configuration #1 chosen from 1 choice
    > hub 3-0:1.0: USB hub found
    > hub 3-0:1.0: 4 ports detected
    > USB Universal Host Controller Interface driver v3.0
    > Initializing USB Mass Storage driver...
    > pccard: PCMCIA card inserted into slot 0
    > cs: memory probe 0xf5000000-0xf6ffffff: excluding 0xf6000000-0xf61fffff
    > pcmcia: registering new device pcmcia0.0
    > usb 2-1: new low speed USB device using ohci_hcd and address 2
    > usb 2-1: configuration #1 chosen from 1 choice
    > usb 2-2: new low speed USB device using ohci_hcd and address 3
    > usb 2-2: configuration #1 chosen from 1 choice
    > usbcore: registered new interface driver usb-storage
    > USB Mass Storage support registered.
    > input: Microsoft Microsoft IntelliMouse® Optical as /class/input/input0
    > input: USB HID v1.00 Mouse [Microsoft Microsoft IntelliMouse® Optical] on usb-0000:00:02.0-1
    > input: DELL DELL USB Keyboard as /class/input/input1
    > input: USB HID v1.10 Keyboard [DELL DELL USB Keyboard] on usb-0000:00:02.0-2
    > usbcore: registered new interface driver usbhid
    > drivers/usb/input/hid-core.c: v2.6:USB HID core driver
    > PNP: No PS/2 controller found. Probing ports directly.
    > serio: i8042 KBD port at 0x60,0x64 irq 1
    > serio: i8042 AUX port at 0x60,0x64 irq 12
    > mice: PS/2 mouse device common for all mice
    > i2c /dev entries driver
    > Advanced Linux Sound Architecture Driver Version 1.0.13 (Tue Nov 28 14:07:24 2006 UTC).
    > ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 23
    > ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 23 (level, high) -> IRQ 18
    > PCI: Setting latency timer of device 0000:00:06.0 to 64
    > intel8x0_measure_ac97_clock: measured 60001 usecs
    > intel8x0: clocking to 55385
    > ALSA device list:
    > #0: NVidia CK8S with ALC850 at 0xf7001000, irq 18
    > ip_conntrack version 2.4 (8191 buckets, 65528 max) - 176 bytes per conntrack
    > ip_tables: (C) 2000-2006 Netfilter Core Team
    > TCP cubic registered
    > NET: Registered protocol family 1
    > NET: Registered protocol family 17
    > ieee80211: 802.11 data/management/control stack, git-1.1.13
    > ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
    > ieee80211_crypt: registered algorithm 'NULL'
    > ieee80211_crypt: registered algorithm 'WEP'
    > Using IPI Shortcut mode
    > Time: tsc clocksource has been installed.
    > kjournald starting. Commit interval 5 seconds
    > EXT3-fs: mounted filesystem with ordered data mode.
    > VFS: Mounted root (ext3 filesystem) readonly.
    > Freeing unused kernel memory: 184k freed
    > cs: IO port probe 0x100-0x3af: excluding 0x290-0x297
    > cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
    > cs: IO port probe 0x820-0x8ff: clean.
    > cs: IO port probe 0xc00-0xcf7: clean.
    > cs: IO port probe 0xa00-0xaff: clean.
    > orinoco 0.15 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al)
    > orinoco_cs 0.15 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al)
    > pcmcia: request for exclusive IRQ could not be fulfilled.
    > pcmcia: the driver needs updating to supported shared IRQ lines.
    > eth2: failed to initialize firmware (err = -19)
    > orinoco_cs: register_netdev() failed
    > pcmcia: request for exclusive IRQ could not be fulfilled.
    > pcmcia: the driver needs updating to supported shared IRQ lines.
    > eth2: failed to initialize firmware (err = -19)
    > orinoco_cs: register_netdev() failed
    > EXT3 FS on hda3, internal journal
    > kjournald starting. Commit interval 5 seconds
    > EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
    > EXT3 FS on hda2, internal journal
    > EXT3-fs: mounted filesystem with ordered data mode.
    > kjournald starting. Commit interval 5 seconds
    > EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
    > EXT3 FS on hda6, internal journal
    > EXT3-fs: mounted filesystem with ordered data mode.
    > Adding 1052216k swap on /dev/hda5. Priority:-1 extents:1 across:1052216k
    > r8169: eth1: link down
    > process `named' is using obsolete setsockopt SO_BSDCOMPAT
    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

    \
     
     \ /
      Last update: 2007-02-19 08:15    [W:0.106 / U:31.072 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site