lkml.org 
[lkml]   [2007]   [Dec]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    Patch in this message
    /
    Date
    From
    SubjectPATA_HPT37X embezzles two ports
    Just to inform everybody:

    PATA_HPT37X embezzles two ports.

    It was fixed on 2.6.23.1 by a patch from Alan
    http://bugzilla.kernel.org/show_bug.cgi?id=9261

    But reoccurs in 2.6.24-rc5

    I just diffed the dmesg here, you can find the complete dmesg in the bugzilla
    http://bugzilla.kernel.org/show_bug.cgi?id=9261

    diff -Nrup hpt-2.6.23.1 hpt-2.6.24-rc5
    --- hpt-2.6.23.1 2007-12-12 15:40:11.000000000 +0100
    +++ hpt-2.6.24-rc5 2007-12-12 16:28:00.000000000 +0100
    @@ -1,182 +1,4 @@
    -Linux version 2.6.23.1 (root@enterprise) (gcc version 4.1.2 (Gentoo
    4.1.2)) #2 Tue Dec 11 22:43:59 CET 2007
    -BIOS-provided physical RAM map:
    - BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    - BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    - BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
    - BIOS-e820: 0000000000100000 - 000000005ff30000 (usable)
    - BIOS-e820: 000000005ff30000 - 000000005ff40000 (ACPI data)
    - BIOS-e820: 000000005ff40000 - 000000005fff0000 (ACPI NVS)
    - BIOS-e820: 000000005fff0000 - 0000000060000000 (reserved)
    - BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
    -639MB HIGHMEM available.
    -896MB LOWMEM available.
    -Entering add_active_range(0, 0, 393008) 0 entries of 256 used
    -Zone PFN ranges:
    - DMA 0 -> 4096
    - Normal 4096 -> 229376
    - HighMem 229376 -> 393008
    -Movable zone start PFN for each node
    -early_node_map[1] active PFN ranges
    - 0: 0 -> 393008
    -On node 0 totalpages: 393008
    - DMA zone: 32 pages used for memmap
    - DMA zone: 0 pages reserved
    - DMA zone: 4064 pages, LIFO batch:0
    - Normal zone: 1760 pages used for memmap
    - Normal zone: 223520 pages, LIFO batch:31
    - HighMem zone: 1278 pages used for memmap
    - HighMem zone: 162354 pages, LIFO batch:31
    - Movable zone: 0 pages used for memmap
    -DMI 2.3 present.
    -ACPI: RSDP 000F9BC0, 0014 (r0 ACPIAM)
    -ACPI: RSDT 5FF30000, 0030 (r1 A M I OEMRSDT 2000503 MSFT 97)
    -ACPI: FACP 5FF30200, 0081 (r2 A M I OEMFACP 2000503 MSFT 97)
    -ACPI: DSDT 5FF30360, 343A (r1 P4V88 P4V88001 1 INTL 2002026)
    -ACPI: FACS 5FF40000, 0040
    -ACPI: APIC 5FF30300, 0052 (r1 A M I OEMAPIC 2000503 MSFT 97)
    -ACPI: OEMB 5FF40040, 003F (r1 A M I OEMBIOS 2000503 MSFT 97)
    -ACPI: PM-Timer IO Port: 0x808
    -ACPI: Local APIC address 0xfee00000
    -ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
    -Processor #0 15:4 APIC version 20
    -ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
    -ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
    -IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23
    -ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    -ACPI: IRQ0 used by override.
    -ACPI: IRQ2 used by override.
    -ACPI: IRQ9 used by override.
    -Enabling APIC mode: Flat. Using 1 I/O APICs
    -Using ACPI (MADT) for SMP configuration information
    -Allocating PCI resources starting at 70000000 (gap: 60000000:9ffc0000)
    -Built 1 zonelists in Zone order. Total pages: 389938
    -Kernel command line: root=/dev/md1
    -mapped APIC to ffffb000 (fee00000)
    -mapped IOAPIC to ffffa000 (fec00000)
    -Enabling fast FPU save and restore... done.
    -Enabling unmasked SIMD FPU exception support... done.
    -Initializing CPU#0
    -PID hash table entries: 4096 (order: 12, 16384 bytes)
    -Detected 2659.603 MHz processor.
    -Console: colour VGA+ 80x25
    -console [tty0] enabled
    -Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    -Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    -Memory: 1552008k/1572032k available (3754k kernel code, 18872k
    reserved, 1349k data, 232k init, 654528k highmem)
    -virtual kernel memory layout:
    - fixmap : 0xfffa8000 - 0xfffff000 ( 348 kB)
    - pkmap : 0xff800000 - 0xffc00000 (4096 kB)
    - vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
    - lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
    - .init : 0xc0600000 - 0xc063a000 ( 232 kB)
    - .data : 0xc04aaa28 - 0xc05fc19c (1349 kB)
    - .text : 0xc0100000 - 0xc04aaa28 (3754 kB)
    -Checking if this processor honours the WP bit even in supervisor mode... Ok.
    -Calibrating delay using timer specific routine.. 5323.32 BogoMIPS (lpj=2661663)
    -Mount-cache hash table entries: 512
    -CPU: After generic identify, caps: bfebfbff 00000000 00000000
    00000000 0000441d 00000000 00000000 00000000
    -monitor/mwait feature present.
    -using mwait in idle threads.
    -CPU: Trace cache: 12K uops, L1 D cache: 16K
    -CPU: L2 cache: 256K
    -CPU: After all inits, caps: bfebfbff 00000000 00000000 0000b180
    0000441d 00000000 00000000 00000000
    -Intel machine check architecture supported.
    -Intel machine check reporting enabled on CPU#0.
    -CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
    -CPU0: Thermal monitoring enabled
    -Compat vDSO mapped to ffffe000.
    -CPU: Intel(R) Celeron(R) CPU 2.66GHz stepping 01
    -Checking 'hlt' instruction... OK.
    -ACPI: Core revision 20070126
    -ENABLING IO-APIC IRQs
    -..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
    -xor: automatically using best checksumming function: pIII_sse
    - pIII_sse : 4320.000 MB/sec
    -xor: using function: pIII_sse (4320.000 MB/sec)
    -NET: Registered protocol family 16
    -No dock devices found.
    -ACPI: bus type pci registered
    -PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
    -PCI: Using configuration type 1
    -Setting up standard PCI resources
    -ACPI: EC: Look up EC in DSDT
    -ACPI: Interpreter enabled
    -ACPI: (supports S0 S5)
    -ACPI: Using IOAPIC for interrupt routing
    -ACPI: PCI Root Bridge [PCI0] (0000:00)
    -ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    -ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
    -ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15)
    -ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
    -ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 7 10 11 14 15)
    -ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
    -ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
    -ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
    -ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
    -ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] -
    E5, should be D8 [20070126]
    -Linux Plug and Play Support v0.97 (c) Adam Belay
    -pnp: PnP ACPI init
    -ACPI: bus type pnp registered
    -pnp: PnP ACPI: found 13 devices
    -ACPI: ACPI bus type pnp unregistered
    -SCSI subsystem initialized
    -libata version 2.21 loaded.
    -usbcore: registered new interface driver usbfs
    -usbcore: registered new interface driver hub
    -usbcore: registered new device driver usb
    -PCI: Using ACPI for IRQ routing
    -PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
    -Time: tsc clocksource has been installed.
    -pnp: 00:08: iomem range 0xfec80000-0xfec800ff has been reserved
    -pnp: 00:08: iomem range 0xfec00000-0xfec00fff has been reserved
    -pnp: 00:08: iomem range 0xfee00000-0xfee00fff has been reserved
    -pnp: 00:08: iomem range 0xfff80000-0xffffffff could not be reserved
    -pnp: 00:0c: iomem range 0x0-0x9ffff could not be reserved
    -pnp: 00:0c: iomem range 0xc0000-0xdffff could not be reserved
    -pnp: 00:0c: iomem range 0xe0000-0xfffff could not be reserved
    -pnp: 00:0c: iomem range 0x100000-0x5fffffff could not be reserved
    -PCI: Bridge: 0000:00:01.0
    - IO window: disabled.
    - MEM window: f3e00000-f7efffff
    - PREFETCH window: d3d00000-f3cfffff
    -PCI: Setting latency timer of device 0000:00:01.0 to 64
    -NET: Registered protocol family 2
    -IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
    -TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
    -TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
    -TCP: Hash tables configured (established 131072 bind 65536)
    -TCP reno registered
    -Machine check exception polling timer started.
    -IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
    -audit: initializing netlink socket (disabled)
    -audit(1197473373.195:1): initialized
    -highmem bounce pool size: 64 pages
    -VFS: Disk quotas dquot_6.5.1
    -Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    -Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
    -NTFS driver 2.1.28 [Flags: R/W].
    -SGI XFS with large block numbers, no debug enabled
    -async_tx: api initialized (sync-only)
    -io scheduler noop registered
    -io scheduler anticipatory registered (default)
    -io scheduler deadline registered
    -io scheduler cfq registered
    -PCI: VIA PCI bridge detected. Disabling DAC.
    -PCI: Bypassing VIA 8237 APIC De-Assert Message
    -Boot video device is 0000:01:00.0
    -input: Power Button (FF) as /devices/virtual/input/input0
    -ACPI: Power Button (FF) [PWRF]
    -input: Power Button (CM) as /devices/virtual/input/input1
    -ACPI: Power Button (CM) [PWRB]
    -ACPI: Processor [CPU1] (supports 16 throttling states)
    -lp: driver loaded but no devices found
    -Real Time Clock Driver v1.12ac
    -Non-volatile memory driver v1.2
    -Linux agpgart interface v0.102
    -agpgart: Detected VIA PT880 chipset
    -agpgart: AGP aperture is 64M @ 0xf8000000
    -Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
    -serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    +irq = 4) is a 16550A
    00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    parport_pc 00:06: reported by Plug and Play ACPI
    parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
    @@ -200,8 +22,8 @@ ACPI: PCI Interrupt 0000:00:0f.0[B] -> G
    sata_via 0000:00:0f.0: routed to hard irq line 10
    scsi0 : sata_via
    scsi1 : sata_via
    -ata1: SATA max UDMA/133 cmd 0x0001e800 ctl 0x0001e402 bmdma 0x0001d800 irq 18
    -ata2: SATA max UDMA/133 cmd 0x0001e000 ctl 0x0001dc02 bmdma 0x0001d808 irq 18
    +ata1: SATA max UDMA/133 cmd 0xe800 ctl 0xe400 bmdma 0xd800 irq 18
    +ata2: SATA max UDMA/133 cmd 0xe000 ctl 0xdc00 bmdma 0xd808 irq 18
    ata1: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
    ata2: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
    pata_hpt37x: BIOS has not set timing clocks.
    @@ -210,8 +32,10 @@ PCI: Enabling device 0000:00:0a.0 (0000
    ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 19
    scsi2 : pata_hpt37x
    scsi3 : pata_hpt37x
    -ata3: PATA max UDMA/100 cmd 0x00011400 ctl 0x00011412 bmdma 0x00011000 irq 19
    -ata4: PATA max UDMA/100 cmd 0x00011408 ctl 0x00011416 bmdma 0x00011008 irq 19
    +ata3: PATA max UDMA/100 cmd 0x1400 ctl 0x1410 bmdma 0x1000 irq 19
    +ata4: PATA max UDMA/100 cmd 0x1408 ctl 0x1414 bmdma 0x1008 irq 19
    +Find mode for 8 reports AC1F48A
    +Find mode for 8 reports AC1F48A
    ata3.00: ATA-7: Maxtor 6Y200P0, YAR41BW0, max UDMA/133
    ata3.00: 398297088 sectors, multi 0: LBA48
    ata3.01: ATA-7: Maxtor 6Y200P0, YAR41BW0, max UDMA/133
    @@ -222,6 +46,8 @@ Find mode for DMA 69 reports 12848242
    Find mode for DMA 69 reports 12848242
    ata3.00: configured for UDMA/100
    ata3.01: configured for UDMA/100
    +Find mode for 8 reports AC1F48A
    +Find mode for 8 reports AC1F48A
    ata4.00: ATA-7: Maxtor 6L250R0, BAJ41G20, max UDMA/133
    ata4.00: 490234752 sectors, multi 0: LBA48
    ata4.01: ATA-7: Maxtor 6L250R0, BAH41G10, max UDMA/133
    @@ -285,48 +111,18 @@ pata_hpt37x: bus clock 33MHz, using 50MH
    ACPI: PCI Interrupt 0000:00:0a.1[A] -> GSI 18 (level, low) -> IRQ 19
    scsi4 : pata_hpt37x
    scsi5 : pata_hpt37x
    -ata5: PATA max UDMA/100 cmd 0x0001b000 ctl 0x0001ac02 bmdma 0x0001a000 irq 19
    -ata6: PATA max UDMA/100 cmd 0x0001a800 ctl 0x0001a402 bmdma 0x0001a008 irq 19
    -ata6.00: ATA-7: Maxtor 5A250J0, RAM51VV0, max UDMA/133
    -ata6.00: 490234752 sectors, multi 0: LBA48
    -ata6.01: ATA-7: HDT722525DLAT80, V44OA96A, max UDMA/133
    -ata6.01: 488397168 sectors, multi 0: LBA48
    -Find mode for 12 reports A81F442
    -Find mode for 12 reports A81F442
    -Find mode for DMA 69 reports 12848242
    -Find mode for DMA 69 reports 12848242
    -ata6.00: configured for UDMA/100
    -ata6.01: configured for UDMA/100
    -scsi 5:0:0:0: Direct-Access ATA Maxtor 5A250J0 RAM5 PQ: 0 ANSI: 5
    -sd 5:0:0:0: [sde] 490234752 512-byte hardware sectors (251000 MB)
    -sd 5:0:0:0: [sde] Write Protect is off
    -sd 5:0:0:0: [sde] Mode Sense: 00 3a 00 00
    -sd 5:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't
    support DPO or FUA
    -sd 5:0:0:0: [sde] 490234752 512-byte hardware sectors (251000 MB)
    -sd 5:0:0:0: [sde] Write Protect is off
    -sd 5:0:0:0: [sde] Mode Sense: 00 3a 00 00
    -sd 5:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't
    support DPO or FUA
    - sde: sde1
    -sd 5:0:0:0: [sde] Attached SCSI disk
    -sd 5:0:0:0: Attached scsi generic sg4 type 0
    -scsi 5:0:1:0: Direct-Access ATA HDT722525DLAT80 V44O PQ: 0 ANSI: 5
    -sd 5:0:1:0: [sdf] 488397168 512-byte hardware sectors (250059 MB)
    -sd 5:0:1:0: [sdf] Write Protect is off
    -sd 5:0:1:0: [sdf] Mode Sense: 00 3a 00 00
    -sd 5:0:1:0: [sdf] Write cache: enabled, read cache: enabled, doesn't
    support DPO or FUA
    -sd 5:0:1:0: [sdf] 488397168 512-byte hardware sectors (250059 MB)
    -sd 5:0:1:0: [sdf] Write Protect is off
    -sd 5:0:1:0: [sdf] Mode Sense: 00 3a 00 00
    -sd 5:0:1:0: [sdf] Write cache: enabled, read cache: enabled, doesn't
    support DPO or FUA
    - sdf: sdf1
    -sd 5:0:1:0: [sdf] Attached SCSI disk
    -sd 5:0:1:0: Attached scsi generic sg5 type 0
    -pata_via 0000:00:0f.1: version 0.3.2
    +ata5: PATA max UDMA/100 cmd 0xb000 ctl 0xac00 bmdma 0xa000 irq 19
    +ata6: PATA max UDMA/100 cmd 0xa800 ctl 0xa400 bmdma 0xa008 irq 19
    +Find mode for 8 reports AC1F48A
    +Find mode for 8 reports AC1F48A
    +Find mode for 8 reports AC1F48A
    +Find mode for 8 reports AC1F48A
    +pata_via 0000:00:0f.1: version 0.3.3
    ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 18
    scsi6 : pata_via
    scsi7 : pata_via
    -ata7: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001fc00 irq 14
    -ata8: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001fc08 irq 15
    +ata7: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xfc00 irq 14
    +ata8: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xfc08 irq 15
    ata7.00: ATA-7: Maxtor 6Y160P0, YAR41BW0, max UDMA/133
    ata7.00: 320173056 sectors, multi 16: LBA48
    ata7.01: ATA-7: Maxtor 6Y160P0, YAR41BW0, max UDMA/133
    @@ -336,31 +132,31 @@ ata7.01: configured for UDMA/133
    ata8.01: ATAPI: ATAPI-CD ROM-DRIVE-52MAX, Ver 52OP, max UDMA/33
    ata8.01: configured for UDMA/33
    scsi 6:0:0:0: Direct-Access ATA Maxtor 6Y160P0 YAR4 PQ: 0 ANSI: 5
    -sd 6:0:0:0: [sdg] 320173056 512-byte hardware sectors (163929 MB)
    -sd 6:0:0:0: [sdg] Write Protect is off
    -sd 6:0:0:0: [sdg] Mode Sense: 00 3a 00 00
    -sd 6:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't
    support DPO or FUA
    -sd 6:0:0:0: [sdg] 320173056 512-byte hardware sectors (163929 MB)
    -sd 6:0:0:0: [sdg] Write Protect is off
    -sd 6:0:0:0: [sdg] Mode Sense: 00 3a 00 00
    -sd 6:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't
    support DPO or FUA
    - sdg: sdg1 sdg2 sdg3
    -sd 6:0:0:0: [sdg] Attached SCSI disk
    -sd 6:0:0:0: Attached scsi generic sg6 type 0
    +sd 6:0:0:0: [sde] 320173056 512-byte hardware sectors (163929 MB)
    +sd 6:0:0:0: [sde] Write Protect is off
    +sd 6:0:0:0: [sde] Mode Sense: 00 3a 00 00
    +sd 6:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't
    support DPO or FUA
    +sd 6:0:0:0: [sde] 320173056 512-byte hardware sectors (163929 MB)
    +sd 6:0:0:0: [sde] Write Protect is off
    +sd 6:0:0:0: [sde] Mode Sense: 00 3a 00 00
    +sd 6:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't
    support DPO or FUA
    + sde: sde1 sde2 sde3
    +sd 6:0:0:0: [sde] Attached SCSI disk
    +sd 6:0:0:0: Attached scsi generic sg4 type 0
    scsi 6:0:1:0: Direct-Access ATA Maxtor 6Y160P0 YAR4 PQ: 0 ANSI: 5
    -sd 6:0:1:0: [sdh] 320173056 512-byte hardware sectors (163929 MB)
    -sd 6:0:1:0: [sdh] Write Protect is off
    -sd 6:0:1:0: [sdh] Mode Sense: 00 3a 00 00
    -sd 6:0:1:0: [sdh] Write cache: enabled, read cache: enabled, doesn't
    support DPO or FUA
    -sd 6:0:1:0: [sdh] 320173056 512-byte hardware sectors (163929 MB)
    -sd 6:0:1:0: [sdh] Write Protect is off
    -sd 6:0:1:0: [sdh] Mode Sense: 00 3a 00 00
    -sd 6:0:1:0: [sdh] Write cache: enabled, read cache: enabled, doesn't
    support DPO or FUA
    - sdh: sdh1 sdh2 sdh3
    -sd 6:0:1:0: [sdh] Attached SCSI disk
    -sd 6:0:1:0: Attached scsi generic sg7 type 0
    +sd 6:0:1:0: [sdf] 320173056 512-byte hardware sectors (163929 MB)
    +sd 6:0:1:0: [sdf] Write Protect is off
    +sd 6:0:1:0: [sdf] Mode Sense: 00 3a 00 00
    +sd 6:0:1:0: [sdf] Write cache: enabled, read cache: enabled, doesn't
    support DPO or FUA
    +sd 6:0:1:0: [sdf] 320173056 512-byte hardware sectors (163929 MB)
    +sd 6:0:1:0: [sdf] Write Protect is off
    +sd 6:0:1:0: [sdf] Mode Sense: 00 3a 00 00
    +sd 6:0:1:0: [sdf] Write cache: enabled, read cache: enabled, doesn't
    support DPO or FUA
    + sdf: sdf1 sdf2 sdf3
    +sd 6:0:1:0: [sdf] Attached SCSI disk
    +sd 6:0:1:0: Attached scsi generic sg5 type 0
    scsi 7:0:1:0: CD-ROM ATAPI-CD ROM-DRIVE-52MAX 52OP PQ: 0 ANSI: 5
    -scsi 7:0:1:0: Attached scsi generic sg8 type 5
    +scsi 7:0:1:0: Attached scsi generic sg6 type 5
    ieee1394: raw1394: /dev/raw1394 device initialized
    ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 20
    ehci_hcd 0000:00:10.4: EHCI Host Controller
    @@ -416,25 +212,25 @@ md: raid0 personality registered for lev
    md: raid1 personality registered for level 1
    md: raid10 personality registered for level 10
    raid6: int32x1 664 MB/s
    -raid6: int32x2 738 MB/s
    -raid6: int32x4 617 MB/s
    -raid6: int32x8 480 MB/s
    -raid6: mmxx1 1601 MB/s
    -raid6: mmxx2 1660 MB/s
    -raid6: sse1x1 937 MB/s
    -raid6: sse1x2 1058 MB/s
    -raid6: sse2x1 1906 MB/s
    -raid6: sse2x2 1750 MB/s
    -raid6: using algorithm sse2x1 (1906 MB/s)
    +raid6: int32x2 742 MB/s
    +raid6: int32x4 621 MB/s
    +raid6: int32x8 492 MB/s
    +raid6: mmxx1 1613 MB/s
    +raid6: mmxx2 1667 MB/s
    +raid6: sse1x1 941 MB/s
    +raid6: sse1x2 1062 MB/s
    +raid6: sse2x1 1917 MB/s
    +raid6: sse2x2 1761 MB/s
    +raid6: using algorithm sse2x1 (1917 MB/s)
    md: raid6 personality registered for level 6
    md: raid5 personality registered for level 5
    md: raid4 personality registered for level 4
    md: multipath personality registered for level -4
    md: faulty personality registered for level -5
    -device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised:
    dm-devel@redhat.com
    +device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised:
    dm-devel@redhat.com
    usbcore: registered new interface driver usbhid
    drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
    -Advanced Linux Sound Architecture Driver Version 1.0.14 (Fri Jul 20
    09:12:58 2007 UTC).
    +Advanced Linux Sound Architecture Driver Version 1.0.15 (Tue Nov 20
    19:16:42 2007 UTC).
    ALSA device list:
    No soundcards found.
    oprofile: using NMI interrupt.
    @@ -447,7 +243,7 @@ u32 classifier
    input device check on
    Actions configured
    Netfilter messages via NETLINK v0.30.
    -nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
    +nf_conntrack version 0.5.0 (14336 buckets, 57344 max)
    ctnetlink v0.93: registering with nfnetlink.
    IPv4 over IPv4 tunneling driver
    ip_tables: (C) 2000-2006 Netfilter Core Team
    @@ -456,71 +252,67 @@ arp_tables: (C) 2002 David S. Miller
    TCP cubic registered
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    +RPC: Registered udp transport module.
    +RPC: Registered tcp transport module.
    p4-clockmod: P4/Xeon(TM) CPU On-Demand Clock Modulation available
    Using IPI Shortcut mode
    md: Autodetecting RAID arrays.
    +md: Scanned 8 and added 8 devices.
    md: autorun ...
    -md: considering sdh3 ...
    -md: adding sdh3 ...
    -md: sdh1 has different UUID to sdh3
    -md: adding sdg3 ...
    -md: sdg1 has different UUID to sdh3
    -md: sdf1 has different UUID to sdh3
    -md: sde1 has different UUID to sdh3
    -md: sdd1 has different UUID to sdh3
    -md: sdc1 has different UUID to sdh3
    -md: sdb1 has different UUID to sdh3
    -md: sda1 has different UUID to sdh3
    +md: considering sdf3 ...
    +md: adding sdf3 ...
    +md: sdf1 has different UUID to sdf3
    +md: adding sde3 ...
    +md: sde1 has different UUID to sdf3
    +md: sdd1 has different UUID to sdf3
    +md: sdc1 has different UUID to sdf3
    +md: sdb1 has different UUID to sdf3
    +md: sda1 has different UUID to sdf3
    md: created md1
    -md: bind<sdg3>
    -md: bind<sdh3>
    -md: running: <sdh3><sdg3>
    +md: bind<sde3>
    +md: bind<sdf3>
    +md: running: <sdf3><sde3>
    raid1: raid set md1 active with 2 out of 2 mirrors
    -md1: bitmap initialized from disk: read 10/10 pages, set 16 bits
    +md1: bitmap initialized from disk: read 10/10 pages, set 22 bits
    created bitmap (152 pages) for device md1
    -md: considering sdh1 ...
    -md: adding sdh1 ...
    -md: adding sdg1 ...
    -md: sdf1 has different UUID to sdh1
    -md: sde1 has different UUID to sdh1
    -md: sdd1 has different UUID to sdh1
    -md: sdc1 has different UUID to sdh1
    -md: sdb1 has different UUID to sdh1
    -md: sda1 has different UUID to sdh1
    +md: considering sdf1 ...
    +md: adding sdf1 ...
    +md: adding sde1 ...
    +md: sdd1 has different UUID to sdf1
    +md: sdc1 has different UUID to sdf1
    +md: sdb1 has different UUID to sdf1
    +md: sda1 has different UUID to sdf1
    md: created md0
    -md: bind<sdg1>
    -md: bind<sdh1>
    -md: running: <sdh1><sdg1>
    +md: bind<sde1>
    +md: bind<sdf1>
    +md: running: <sdf1><sde1>
    raid1: raid set md0 active with 2 out of 2 mirrors
    md0: bitmap initialized from disk: read 1/1 pages, set 0 bits
    created bitmap (6 pages) for device md0
    -md: considering sdf1 ...
    -md: adding sdf1 ...
    -md: adding sde1 ...
    +md: considering sdd1 ...
    md: adding sdd1 ...
    md: adding sdc1 ...
    -md: sdb1 has different UUID to sdf1
    -md: sda1 has different UUID to sdf1
    +md: sdb1 has different UUID to sdd1
    +md: sda1 has different UUID to sdd1
    md: created md4
    md: bind<sdc1>
    md: bind<sdd1>
    -md: bind<sde1>
    -md: bind<sdf1>
    -md: running: <sdf1><sde1><sdd1><sdc1>
    -raid5: device sdf1 operational as raid disk 3
    -raid5: device sde1 operational as raid disk 2
    +md: running: <sdd1><sdc1>
    raid5: device sdd1 operational as raid disk 1
    raid5: device sdc1 operational as raid disk 0
    -raid5: allocated 4210kB for md4
    -raid5: raid level 5 set md4 active with 4 out of 4 devices, algorithm 2
    +raid5: not enough operational devices for md4 (2/4 failed)
    RAID5 conf printout:
    - --- rd:4 wd:4
    + --- rd:4 wd:2
    disk 0, o:1, dev:sdc1
    disk 1, o:1, dev:sdd1
    - disk 2, o:1, dev:sde1
    - disk 3, o:1, dev:sdf1
    -md4: bitmap initialized from disk: read 15/15 pages, set 0 bits
    -created bitmap (233 pages) for device md4
    +raid5: failed to run raid set md4
    +md: pers->run() failed ...
    +md: do_md_run() returned -5
    +md: md4 stopped.
    +md: unbind<sdd1>
    +md: export_rdev(sdd1)
    +md: unbind<sdc1>
    +md: export_rdev(sdc1)
    md: considering sdb1 ...
    md: adding sdb1 ...
    md: adding sda1 ...
    @@ -538,9 +330,10 @@ VFS: Mounted root (ext3 filesystem) read
    Freeing unused kernel memory: 232k freed
    ath_hal: module license 'Proprietary' taints kernel.
    ath_hal: 0.9.30.13 (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112,
    RF2413, RF5413, RF2133)
    +ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 19 (level, low) -> IRQ 21
    wlan: 0.8.4.2 (0.9.4)
    ath_pci: 0.9.4.5 (0.9.4)
    -ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 17 (level, low) -> IRQ 21
    +ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 17 (level, low) -> IRQ 22
    ath_pci: switching rfkill capability off
    ath_rate_sample: 1.2 (0.9.4)
    ath_pci: switching per-packet transmit power control off
    @@ -555,29 +348,8 @@ wifi0: Use hw queue 2 for WME_AC_VI traf
    wifi0: Use hw queue 3 for WME_AC_VO traffic
    wifi0: Use hw queue 8 for CAB traffic
    wifi0: Use hw queue 9 for beacons
    -wifi0: Atheros 5212: mem=0xf7fe0000, irq=21
    -ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 19 (level, low) -> IRQ 22
    +wifi0: Atheros 5212: mem=0xf7fe0000, irq=22
    EXT3 FS on md1, internal journal
    -kjournald starting. Commit interval 5 seconds
    -EXT3 FS on md3, internal journal
    -EXT3-fs: mounted filesystem with ordered data mode.
    -kjournald starting. Commit interval 5 seconds
    -EXT3 FS on md4, internal journal
    -EXT3-fs: mounted filesystem with ordered data mode.
    -Adding 996020k swap on /dev/sdg2. Priority:-1 extents:1 across:996020k
    -Adding 996020k swap on /dev/sdh2. Priority:-2 extents:1 across:996020k
    -r8169: eth0: link up
    -eth1: link up, 100Mbps, full-duplex, lpa 0x45E1
    -NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
    -NFSD: starting 90-second grace period
    -Shorewall:dmz2fw:reject:IN=ath0 OUT= MAC= SRC=10.3.123.1
    DST=10.3.123.255 LEN=96 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP
    SPT=137 DPT=137 LEN=76
    -Shorewall:dmz2fw:reject:IN=ath0 OUT= MAC= SRC=10.3.123.1
    DST=10.3.123.255 LEN=221 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP
    SPT=138 DPT=138 LEN=201
    -Shorewall:dmz2fw:reject:IN=ath0 OUT= MAC= SRC=10.3.123.1
    DST=10.3.123.255 LEN=96 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP
    SPT=137 DPT=137 LEN=76
    -Shorewall:dmz2fw:reject:IN=ath0 OUT= MAC= SRC=10.3.123.1
    DST=10.3.123.255 LEN=96 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP
    SPT=137 DPT=137 LEN=76
    -Shorewall:dmz2fw:reject:IN=ath0 OUT= MAC= SRC=10.3.123.1
    DST=10.3.123.255 LEN=221 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP
    SPT=138 DPT=138 LEN=201
    -Shorewall:dmz2fw:reject:IN=ath0 OUT= MAC= SRC=10.3.123.1
    DST=10.3.123.255 LEN=221 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP
    SPT=138 DPT=138 LEN=201
    -Shorewall:dmz2fw:reject:IN=ath0 OUT= MAC= SRC=10.3.123.1
    DST=10.3.123.255 LEN=96 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP
    SPT=137 DPT=137 LEN=76
    -Shorewall:dmz2fw:reject:IN=ath0 OUT= MAC= SRC=10.3.123.1
    DST=10.3.123.255 LEN=248 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP
    SPT=138 DPT=138 LEN=228
    -Shorewall:dmz2fw:reject:IN=ath0 OUT= MAC= SRC=10.3.123.1
    DST=10.3.123.255 LEN=239 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP
    SPT=138 DPT=138 LEN=219
    -Shorewall:dmz2fw:reject:IN=ath0 OUT= MAC= SRC=10.3.123.1
    DST=10.3.123.255 LEN=248 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP
    SPT=138 DPT=138 LEN=228
    -Shorewall:dmz2fw:reject:IN=ath0 OUT= MAC= SRC=10.3.123.1
    DST=10.3.123.255 LEN=239 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP
    SPT=138 DPT=138 LEN=219
    +md: md4 stopped.
    +md: bind<sdd1>
    +md: bind<sdc1>

    \
     
     \ /
      Last update: 2007-12-12 16:03    [W:0.069 / U:31.440 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site