![]() | |||||||||||
Messages in this thread |
On Sat, Sep 23, 2006 at 07:03:26AM -0400, Valdis.Kletnieks@vt.edu wrote: > orinoco 0.15 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al) > orinoco_cs 0.15 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al) > pcmcia: request for exclusive IRQ could not be fulfilled. > pcmcia: the driver needs updating to supported shared IRQ lines. > cs: IO port probe 0x100-0x3af: excluding 0x370-0x37f > cs: IO port probe 0x3e0-0x4ff: clean. > cs: IO port probe 0x820-0x8ff: clean. > cs: IO port probe 0xc00-0xcf7: clean. > cs: IO port probe 0xa00-0xaff: clean. > cs: IO port probe 0x100-0x3af: excluding 0x370-0x37f > cs: IO port probe 0x3e0-0x4ff: clean. > cs: IO port probe 0x820-0x8ff: clean. > cs: IO port probe 0xc00-0xcf7: clean. > cs: IO port probe 0xa00-0xaff: clean. > cs: IO port probe 0x100-0x3af: excluding 0x370-0x37f > cs: IO port probe 0x3e0-0x4ff: clean. > cs: IO port probe 0x820-0x8ff: clean. > cs: IO port probe 0xc00-0xcf7: clean. > cs: IO port probe 0xa00-0xaff: clean. > eth2: Hardware identity 0005:0004:0005:0000 > eth2: Station identity 001f:0001:0008:000a > eth2: Firmware determined as Lucent/Agere 8.10 > eth2: Ad-hoc demo mode supported > eth2: IEEE standard IBSS ad-hoc mode supported > eth2: WEP supported, 104-bit key > eth2: MAC address 00:02:2D:5C:11:48 > eth2: Station name "HERMES I" > eth2: ready > eth2: orinoco_cs at 2.0, irq 11, io 0xe100-0xe13f > [rename_device:1295]: Changing netdevice name from [eth2] to [eth5] > Non-volatile memory driver v1.2 > > and under -rc7-mm1, I see: > > pccard: CardBus card inserted into slot 0 > PCI: Enabling device 0000:03:00.0 (0000 -> 0003) > ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 > PCI: Setting latency timer of device 0000:03:00.0 to 64 > eth1: Xircom cardbus revision 3 at irq 11 > PCI: Enabling device 0000:03:00.1 (0000 -> 0003) > ACPI: PCI Interrupt 0000:03:00.1[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 > 0000:03:00.1: ttyS1 at I/O 0xe080 (irq = 11) is a 16550A > pccard: PCMCIA card inserted into slot 2 > ohci1394: fw-host0: AT dma reset ctx=0, aborting transmission > ieee1394: Current remote IRM is not 1394a-2000 compliant, resetting... > ieee1394: Host added: ID:BUS[0-00:1023] GUID[374fc0002a71c021] > Non-volatile memory driver v1.2 > > Hmm.. a lot quieter... So, you have a pcmcia or cardbus card here? I've tried this with a cardbus card and it worked fine. Are you sure you have the latest userspace tools, I didn't think that cs was needed anymore, but again, without a pcmcia device to test this with, I really am not sure :( thanks, greg k-h - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/ | ||||||||||
| Last update: 2006-09-27 06:35 [from the cache] ©2003-2008 | |||||||||||