lkml.org 
[lkml]   [2006]   [Sep]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    From
    SubjectFreecom DVB-T tuner firmware load with ohci(ehci) driver
    Date
    Hi,

    I have bought Kouwell Cardbus adapter with 2 USB2.0 and 2 Firewire ports.
    In my older laptop with i852 chipset and Pentium4 Celeron card works with all
    the devices

    01:04.0 CardBus bridge: Texas Instruments PCI1520 PC card Cardbus Controller
    (rev 01)
    01:04.1 CardBus bridge: Texas Instruments PCI1520 PC card Cardbus Controller
    (rev 01)


    but with my newer laptop i855 chipset Intel Pentium M everythink works except
    my DVB-T card firmware load fails (my flashdrive, my bluetooth dongle
    works...)

    02:0b.0 CardBus bridge: O2 Micro, Inc. OZ711M1/MC1 4-in-1 MemoryCardBus
    Controller (rev 20)
    02:0b.1 CardBus bridge: O2 Micro, Inc. OZ711M1/MC1 4-in-1 MemoryCardBus
    Controller (rev 20)


    In both cases YENTA module is loaded.

    pccard: CardBus card inserted into slot 0
    PCI: Enabling device 0000:03:00.3 (0000 -> 0002)
    ACPI: PCI Interrupt 0000:03:00.3[A] -> Link [LNKC] -> GSI 11 (level, low) ->
    IRQ 11
    ehci_hcd 0000:03:00.3: EHCI Host Controller
    ehci_hcd 0000:03:00.3: new USB bus registered, assigned bus number 5
    ehci_hcd 0000:03:00.3: debug port 1
    ehci_hcd 0000:03:00.3: irq 11, io mem 0x56003800
    ehci_hcd 0000:03:00.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
    usb usb5: configuration #1 chosen from 1 choice
    hub 5-0:1.0: USB hub found
    hub 5-0:1.0: 6 ports detected
    PCI: Enabling device 0000:03:00.4 (0000 -> 0002)
    ACPI: PCI Interrupt 0000:03:00.4[C] -> Link [LNKC] -> GSI 11 (level, low) ->
    IRQ 11
    PCI: Setting latency timer of device 0000:03:00.4 to 64
    usb 5-2: new high speed USB device using ehci_hcd and address 2
    ohci1394: fw-host1: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[56003000-560037ff]
    Max Packet=[2048] IR/IT contexts=[4/8]
    eth1394: eth3: IEEE-1394 IPv4 over 1394 Ethernet (fw-host1)
    usb 5-2: configuration #1 chosen from 1 choice
    ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
    PCI: Enabling device 0000:03:00.0 (0000 -> 0002)
    ACPI: PCI Interrupt 0000:03:00.0[B] -> Link [LNKC] -> GSI 11 (level, low) ->
    IRQ 11
    ohci_hcd 0000:03:00.0: OHCI Host Controller
    ohci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 6
    ohci_hcd 0000:03:00.0: irq 11, io mem 0x56000000
    usb usb6: configuration #1 chosen from 1 choice
    hub 6-0:1.0: USB hub found
    hub 6-0:1.0: 2 ports detected
    PCI: Enabling device 0000:03:00.1 (0000 -> 0002)
    ACPI: PCI Interrupt 0000:03:00.1[B] -> Link [LNKC] -> GSI 11 (level, low) ->
    IRQ 11
    ohci_hcd 0000:03:00.1: OHCI Host Controller
    ohci_hcd 0000:03:00.1: new USB bus registered, assigned bus number 7
    ohci_hcd 0000:03:00.1: irq 11, io mem 0x56001000
    usb usb7: configuration #1 chosen from 1 choice
    hub 7-0:1.0: USB hub found
    hub 7-0:1.0: 2 ports detected
    PCI: Enabling device 0000:03:00.2 (0000 -> 0002)
    ACPI: PCI Interrupt 0000:03:00.2[B] -> Link [LNKC] -> GSI 11 (level, low) ->
    IRQ 11
    ohci_hcd 0000:03:00.2: OHCI Host Controller
    ohci_hcd 0000:03:00.2: new USB bus registered, assigned bus number 8
    ohci_hcd 0000:03:00.2: irq 11, io mem 0x56002000
    usb usb8: configuration #1 chosen from 1 choice
    hub 8-0:1.0: USB hub found
    hub 8-0:1.0: 2 ports detected
    ieee1394: Host added: ID:BUS[1-00:1023] GUID[0090e600000024f7]
    dvb-usb: found a 'WideView WT-220U PenType Receiver (Typhoon/Freecom)' in cold
    state, will try to load a firmware
    dvb-usb: downloading firmware from file 'dvb-usb-wt220u-02.fw'
    dvb-usb: error while transferring firmware (transferred size: -71, block size:
    16)
    dvb-usb: firmware download failed at 2135 with -22
    usbcore: registered new driver dvb_usb_dtt200u


    Can anybody help??

    This is really strange.

    Michal
    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

    \
     
     \ /
      Last update: 2006-09-22 23:23    [W:0.025 / U:0.400 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site