![]() | |||||||||||||
Messages in this thread |
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 2.6.17.2, libata for 2.6.17 from Tejun Heo (http://home-tj.org/files/libata-tj-stable/libata-tj-2.6.17-20060625.tar.bz2), pata_ali from Jeff Garzik tree patched to add parameter to set transfer mask for ATAPI (as already posted it does not detect CD-ROM in DMA so I clamp it to PIO4). System - TOSHIBA Portege 4000. Several times after switching to libata system hung on resume from suspend to RAM. It is stuck attempting to initialize hard drive and doing recovery in loop. Unfortunately this notebook does not have any serial port so it is somewhat hard capture any console output during resume. I have been using STR with legacy IDE drivers without any problems so far. Any idea how to debug it welcome. Thank you - -andrey {pts/0}% sudo lspci -vvv 00:00.0 Host bridge: ALi Corporation M1644/M1644T Northbridge+Trident (rev 01) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+ Latency: 0 Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M] Capabilities: [b0] AGP version 2.0 Status: RQ=28 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none> Capabilities: [a4] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:01.0 PCI bridge: ALi Corporation PCI to AGP Controller (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: f7f00000-fdffffff Prefetchable memory behind bridge: 3c000000-3c0fffff Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR+ BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B- 00:02.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) (prog-if 10 [OHCI]) Subsystem: Toshiba America Info Systems Unknown device 0004 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (20000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at f7eff000 (32-bit, non-prefetchable) [size=4K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:04.0 IDE interface: ALi Corporation M5229 IDE (rev c3) (prog-if f0) Subsystem: Toshiba America Info Systems Unknown device 0004 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (500ns min, 1000ns max) Interrupt: pin A routed to IRQ 255 Region 4: I/O ports at eff0 [size=16] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:06.0 Multimedia audio controller: ALi Corporation M5451 PCI AC-Link Controller Audio Device (rev 01) Subsystem: Toshiba America Info Systems Unknown device 0001 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR+ <PERR+ Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at ed00 [size=256] Region 1: Memory at f7efe000 (32-bit, non-prefetchable) [size=4K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:07.0 ISA bridge: ALi Corporation M1533/M1535 PCI to ISA Bridge [Aladdin IV/V/V+] Subsystem: Toshiba America Info Systems Unknown device 0004 Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: [a0] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:08.0 Bridge: ALi Corporation M7101 Power Management Controller [PMU] Subsystem: Toshiba America Info Systems Unknown device 0001 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:0a.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro 100] (rev 08) Subsystem: Toshiba America Info Systems 8255x-based Fast Ethernet Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (2000ns min, 14000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at f7efd000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at eb40 [size=64] Region 2: Memory at f7d00000 (32-bit, non-prefetchable) [size=1M] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=2 PME- 00:10.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 01) Subsystem: Lucent Technologies Unknown device ab01 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at 3c100000 (32-bit, non-prefetchable) [size=4K] Bus: primary=00, secondary=02, subordinate=05, sec-latency=176 Memory window 0: 30000000-31fff000 (prefetchable) Memory window 1: 32000000-33fff000 I/O window 0: 00001000-000010ff I/O window 1: 00001400-000014ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- PostWrite+ 16-bit legacy interface ports at 0001 00:11.0 CardBus bridge: Toshiba America Info Systems ToPIC100 PCI to Cardbus Bridge with ZV Support (rev 32) Subsystem: Toshiba America Info Systems Unknown device 0001 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168 Interrupt: pin A routed to IRQ 11 Region 0: Memory at 3c101000 (32-bit, non-prefetchable) [size=4K] Bus: primary=00, secondary=06, subordinate=09, sec-latency=0 Memory window 0: 34000000-35fff000 (prefetchable) Memory window 1: 36000000-37fff000 I/O window 0: 00001800-000018ff I/O window 1: 00001c00-00001cff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001 00:11.1 CardBus bridge: Toshiba America Info Systems ToPIC100 PCI to Cardbus Bridge with ZV Support (rev 32) Subsystem: Toshiba America Info Systems Unknown device 0001 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168 Interrupt: pin B routed to IRQ 11 Region 0: Memory at 3c102000 (32-bit, non-prefetchable) [size=4K] Bus: primary=00, secondary=0a, subordinate=0d, sec-latency=0 Memory window 0: 38000000-39fff000 (prefetchable) Memory window 1: 3a000000-3bfff000 I/O window 0: 00002000-000020ff I/O window 1: 00002400-000024ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001 00:12.0 System peripheral: Toshiba America Info Systems SD TypA Controller (rev 03) Subsystem: Toshiba America Info Systems Unknown device 0001 Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 11 Region 0: Memory at f7cffe00 (32-bit, non-prefetchable) [size=512] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 01:00.0 VGA compatible controller: Trident Microsystems CyberBlade XPAi1 (rev 82) (prog-if 00 [VGA]) Subsystem: Toshiba America Info Systems Unknown device 0001 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 8 Interrupt: pin A routed to IRQ 11 Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=32M] Region 1: Memory at fbc00000 (32-bit, non-prefetchable) [size=4M] Region 2: Memory at f8000000 (32-bit, non-prefetchable) [size=32M] Region 3: Memory at f7ff8000 (32-bit, non-prefetchable) [size=32K] [virtual] Expansion ROM at 3c000000 [disabled] [size=64K] Capabilities: [80] AGP version 2.0 Status: RQ=33 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none> Capabilities: [90] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- {pts/0}% Linux version 2.6.17.2-1avb (bor@cooker) (gcc version 4.1.1 20060518 (prerelease)) #26 Fri Jun 30 12:51:27 MSD 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 00000000000eee00 (reserved) BIOS-e820: 00000000000eee00 - 00000000000ef000 (ACPI NVS) BIOS-e820: 00000000000ef000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001ef60000 (usable) BIOS-e820: 000000001ef60000 - 000000001ef70000 (ACPI data) BIOS-e820: 000000001ef70000 - 0000000020000000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) 495MB LOWMEM available. On node 0 totalpages: 126816 DMA zone: 4096 pages, LIFO batch:0 Normal zone: 122720 pages, LIFO batch:31 DMI 2.3 present. ACPI: RSDP (v000 TOSHIB ) @ 0x000f0090 ACPI: RSDT (v001 TOSHIB 750 0x00970814 TASM 0x04010000) @ 0x1ef60000 ACPI: FADT (v002 TOSHIB 750 0x00970814 TASM 0x04010000) @ 0x1ef60054 ACPI: DSDT (v001 TOSHIB 4000 0x20020417 MSFT 0x0100000a) @ 0x00000000 ACPI: PM-Timer IO Port: 0xee08 Allocating PCI resources starting at 30000000 (gap: 20000000:dff80000) Built 1 zonelists Kernel command line: root=/dev/sda2 resume=/dev/sda1 elevator=cfq vga=791 Local APIC disabled by BIOS -- you can enable it with "lapic" mapped APIC to ffffd000 (013e4000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 2048 (order: 11, 8192 bytes) Detected 747.720 MHz processor. Using pmtmr for high-res timesource Console: colour dummy device 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 499052k/507264k available (1667k kernel code, 7648k reserved, 799k data, 180k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 1496.76 BogoMIPS (lpj=748383) Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0387f9ff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0387f9ff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K CPU serial number disabled. CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: Intel Pentium III (Coppermine) stepping 0a Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 0k freed ACPI: setting ELCR to 0200 (from 0a00) checking if image is initramfs... it is Freeing initrd memory: 292k freed NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfe5ae, last bus=5 Setting up standard PCI resources ACPI: Subsystem revision 20060127 ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 PCI quirk: region ee00-ee3f claimed by ali7101 ACPI PCI quirk: region ef00-ef1f claimed by ali7101 SMB Boot video device is 0000:01:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT] ACPI: Power Resource [PFAN] (off) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 12 devices PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca) PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: f7f00000-fdffffff PREFETCH window: 3c000000-3c0fffff PCI: Bus 2, cardbus bridge: 0000:00:10.0 IO window: 00001000-000010ff IO window: 00001400-000014ff PREFETCH window: 30000000-31ffffff MEM window: 32000000-33ffffff PCI: Bus 6, cardbus bridge: 0000:00:11.0 IO window: 00001800-000018ff IO window: 00001c00-00001cff PREFETCH window: 34000000-35ffffff MEM window: 36000000-37ffffff PCI: Bus 10, cardbus bridge: 0000:00:11.1 IO window: 00002000-000020ff IO window: 00002400-000024ff PREFETCH window: 38000000-39ffffff MEM window: 3a000000-3bffffff PCI: Setting latency timer of device 0000:00:01.0 to 64 PCI: Enabling device 0000:00:10.0 (0000 -> 0003) ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 PCI: Enabling device 0000:00:11.0 (0000 -> 0003) ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:11.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: Enabling device 0000:00:11.1 (0000 -> 0003) ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:11.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 6, 262144 bytes) TCP bind hash table entries: 8192 (order: 5, 163840 bytes) TCP: Hash tables configured (established 16384 bind 8192) TCP reno registered audit: initializing netlink socket (disabled) audit(1151845047.480:1): initialized Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Activating ISA DMA hang workarounds. vesafb: framebuffer at 0xfc000000, mapped to 0xdf880000, using 3072k, total 16384k vesafb: mode is 1024x768x16, linelength=2048, pages=9 vesafb: protected mode interface info at c000:775e vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device Real Time Clock Driver v1.12ac Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice NET: Registered protocol family 1 Using IPI Shortcut mode ACPI wakeup devices: COM USB1 ASND VIY0 VIY1 LAN MPC0 MPC1 NOV0 LID ACPI: (supports S0 S3 S4 S5) BIOS EDD facility v0.16 2004-Jun-25, 1 devices found Freeing unused kernel memory: 180k freed Write protecting the kernel read-only data: 520k input: AT Translated Set 2 keyboard as /class/input/input0 SCSI subsystem initialized libata version 1.30 loaded. ACPI: PCI Interrupt 0000:00:04.0[A]: no GSI ata1: PATA max UDMA/100 cmd 0x1F0 ctl 0x3F6 bmdma 0xEFF0 irq 14 scsi0 : pata_ali ata1.00: configured for UDMA/33 Vendor: ATA Model: IC25N020ATDA04-0 Rev: DA3O Type: Direct-Access ANSI SCSI revision: 05 ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xEFF8 irq 15 scsi1 : pata_ali input: ImPS/2 Generic Wheel Mouse as /class/input/input1 ata2.00: configured for PIO4 Vendor: TOSHIBA Model: DVD-ROM SD-C2502 Rev: 1313 Type: CD-ROM ANSI SCSI revision: 05 SCSI device sda: 39070080 512-byte hdwr sectors (20004 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 39070080 512-byte hdwr sectors (20004 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 sd 0:0:0:0: Attached scsi disk sda ReiserFS: sda2: found reiserfs format "3.6" with standard journal ReiserFS: sda2: using ordered data mode ReiserFS: sda2: journal params: device sda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: sda2: checking transaction log (sda2) ReiserFS: sda2: replayed 51 transactions in 8 seconds ReiserFS: sda2: Using r5 hash to sort names usbcore: registered new driver usbfs usbcore: registered new driver hub ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKG] -> GSI 11 (level, low) -> IRQ 11 ohci_hcd 0000:00:02.0: OHCI Host Controller ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:02.0: irq 11, io mem 0xf7eff000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 1:0:0:0: Attached scsi CD-ROM sr0 Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected ALi M1644 chipset agpgart: AGP aperture is 64M @ 0xf0000000 ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 Yenta: CardBus bridge found at 0000:00:10.0 [12a3:ab01] Yenta: Enabling burst memory read transactions Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:00:10.0, mfunc 0x01000002, devctl 0x60 Yenta: ISA IRQ mask 0x0000, PCI irq 11 Socket status: 30000011 ACPI: PCI Interrupt 0000:00:11.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 Yenta: CardBus bridge found at 0000:00:11.0 [1179:0001] Yenta: ISA IRQ mask 0x04b8, PCI irq 11 Socket status: 30000007 pccard: PCMCIA card inserted into slot 0 cs: memory probe 0x0c0000-0x0fffff: excluding 0xc0000-0xcbfff 0xe0000-0xfffff cs: memory probe 0x60000000-0x60ffffff: clean. cs: memory probe 0xa0000000-0xa0ffffff: clean. pcmcia: registering new device pcmcia0.0 wlags49_h1_cs v7.18 for PCMCIA, 03/31/2004 14:31:00 by Agere Systems, http://www.agere.com *** Modified for kernel 2.6 by Andrey Borzenkov <arvidjaar@mail.ru> $Revision: 25 $ *** Station Mode (STA) Support: YES *** Access Point Mode (AP) Support: YES eth0: PRI 31 variant 2 version 9.48 eth0: NIC 5 variant 2 version 1.02 eth0: Wireless, io_addr 0x100, irq 11, mac_address 00:02:2D:26:95:6C ACPI: PCI Interrupt 0000:00:11.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 Yenta: CardBus bridge found at 0000:00:11.1 [1179:0001] Yenta: ISA IRQ mask 0x04b8, PCI irq 11 Socket status: 30000007 ACPI: AC Adapter [ADP1] (on-line) ACPI: Battery Slot [BAT1] (battery present) ACPI: Battery Slot [BAT2] (battery absent) ACPI: Power Button (FF) [PWRF] ACPI: Lid Switch [LID] ACPI: Fan [FAN] (off) ACPI: CPU0 (power states: C1[C1] C2[C2]) ACPI: Thermal Zone [THRM] (38 C) toshiba_acpi: Toshiba Laptop ACPI Extras version 0.18 toshiba_acpi: HCI method: \_SB_.VALD.GHCI ACPI: Video Device [VGA] (multi-head: yes rom: yes post: no) ReiserFS: sda2: Removing [35299 359282 0x0 SD]..done ReiserFS: sda2: Removing [160679 286174 0x0 SD]..done ReiserFS: sda2: Removing [79727 236457 0x0 SD]..done ReiserFS: sda2: Removing [45614 236448 0x0 SD]..done ReiserFS: sda2: Removing [45614 236444 0x0 SD]..done ReiserFS: sda2: Removing [45614 236442 0x0 SD]..done ReiserFS: sda2: Removing [45614 236438 0x0 SD]..done ReiserFS: sda2: Removing [45614 236410 0x0 SD]..done ReiserFS: sda2: Removing [45614 236387 0x0 SD]..done ReiserFS: sda2: Removing [45614 236369 0x0 SD]..done ReiserFS: sda2: Removing [45614 236368 0x0 SD]..done ReiserFS: sda2: Removing [45614 236365 0x0 SD]..done ReiserFS: sda2: Removing [45614 236363 0x0 SD]..done ReiserFS: sda2: Removing [45614 236338 0x0 SD]..done ReiserFS: sda2: Removing [45614 236337 0x0 SD]..done ReiserFS: sda2: Removing [45614 236336 0x0 SD]..done ReiserFS: sda2: Removing [45614 236333 0x0 SD]..done ReiserFS: sda2: Removing [45614 236305 0x0 SD]..done ReiserFS: sda2: Removing [45614 236299 0x0 SD]..done ReiserFS: sda2: Removing [45614 236298 0x0 SD]..done ReiserFS: sda2: Removing [45614 235022 0x0 SD]..done ReiserFS: sda2: Removing [45614 235014 0x0 SD]..done ReiserFS: sda2: Removing [45614 234983 0x0 SD]..done ReiserFS: sda2: Removing [45614 234970 0x0 SD]..done ReiserFS: sda2: Removing [45614 234954 0x0 SD]..done ReiserFS: sda2: Removing [45614 234925 0x0 SD]..done ReiserFS: sda2: Removing [45614 234421 0x0 SD]..done ReiserFS: sda2: Removing [45614 234416 0x0 SD]..done ReiserFS: sda2: Removing [45614 234396 0x0 SD]..done ReiserFS: sda2: Removing [45614 233009 0x0 SD]..done ReiserFS: sda2: Removing [45614 233007 0x0 SD]..done ReiserFS: sda2: Removing [45614 233004 0x0 SD]..done ReiserFS: sda2: Removing [45614 232966 0x0 SD]..done ReiserFS: sda2: Removing [45614 123769 0x0 SD]..done ReiserFS: sda2: Removing [45614 100962 0x0 SD]..done ReiserFS: sda2: Removing [45614 87692 0x0 SD]..done ReiserFS: sda2: Removing [178237 79655 0x0 SD]..done ReiserFS: sda2: Removing [45614 74578 0x0 SD]..done ReiserFS: sda2: There were 38 uncompleted unlinks/truncates. Completed Adding 500432k swap on /dev/sda1. Priority:-1 extents:1 across:500432k loop: loaded (max 8 devices) -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.3 (GNU/Linux) iD8DBQFEqMW9R6LMutpd94wRAuC6AJ4kSKl024bAGzYj3R5rqTWiAZAxLQCgyaH4 FYyHc+bSfm1UGAbkylNUQvA= =4/EW -----END PGP SIGNATURE----- - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/ | ||||||||||||
| Last update: 2006-07-03 09:27 [from the cache] ©2003-2008 | |||||||||||||