lkml.org 
[lkml]   [2006]   [Jul]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    SubjectRe: PCI bus is hidden behind transparent bridge
    Sorry to reply to my own message... but I wanted to add something.

    Since I upgraded my kernel back around 2.6.16, I stopped seeing my SMBus
    adapter on the PCI bus, and thus could not get readings from the LM90
    sensor chip on my laptop. After trying the pci=assign-busses parameter,
    the error messages about transparent busses go away, but I still can't
    access the SMBus controller (it uses the i2c-i801 module, in case that
    helps).

    I've attached the dmesg that I get when I specify that parameter; the
    lspci output remains the same.

    --Thomas Tuttle
    Linux version 2.6.18-rc2 (tom@phoenix) (gcc version 3.4.6 (Gentoo 3.4.6-r1, ssp-3.4.5-1.0, pie-8.7.9)) #2 PREEMPT Tue Jul 25 17:36:09 EDT 2006
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000001f740000 (usable)
    BIOS-e820: 000000001f740000 - 000000001f750000 (ACPI data)
    BIOS-e820: 000000001f750000 - 000000001f800000 (ACPI NVS)
    503MB LOWMEM available.
    On node 0 totalpages: 128832
    DMA zone: 4096 pages, LIFO batch:0
    Normal zone: 124736 pages, LIFO batch:31
    DMI 2.3 present.
    ACPI: RSDP (v000 ACPIAM ) @ 0x000f4f70
    ACPI: RSDT (v001 A M I OEMRSDT 0x09000409 MSFT 0x00000097) @ 0x1f740000
    ACPI: FADT (v002 A M I OEMFACP 0x09000409 MSFT 0x00000097) @ 0x1f740200
    ACPI: MADT (v001 A M I OEMAPIC 0x09000409 MSFT 0x00000097) @ 0x1f740300
    ACPI: OEMB (v001 A M I OEMBIOS 0x09000409 MSFT 0x00000097) @ 0x1f750040
    ACPI: DSDT (v001 0ABBD 0ABBD001 0x00000001 MSFT 0x0100000d) @ 0x00000000
    ACPI: PM-Timer IO Port: 0xe408
    ACPI: Local APIC address 0xfee00000
    ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
    Processor #0 6:13 APIC version 20
    ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
    IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
    ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    ACPI: IRQ0 used by override.
    ACPI: IRQ2 used by override.
    ACPI: IRQ9 used by override.
    Enabling APIC mode: Flat. Using 1 I/O APICs
    Using ACPI (MADT) for SMP configuration information
    Allocating PCI resources starting at 20000000 (gap: 1f800000:e0800000)
    Detected 1700.138 MHz processor.
    Built 1 zonelists. Total pages: 128832
    Kernel command line: root=/dev/hda5 vga=0x318 pci=assign-busses
    mapped APIC to ffffd000 (fee00000)
    mapped IOAPIC to ffffc000 (fec00000)
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Initializing CPU#0
    CPU 0 irqstacks, hard=c049b000 soft=c049a000
    PID hash table entries: 2048 (order: 11, 8192 bytes)
    Console: colour dummy device 80x25
    Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
    Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
    Memory: 505532k/515328k available (2378k kernel code, 9372k reserved, 744k data, 192k init, 0k highmem)
    Checking if this processor honours the WP bit even in supervisor mode... Ok.
    Calibrating delay using timer specific routine.. 3401.12 BogoMIPS (lpj=1700560)
    Mount-cache hash table entries: 512
    CPU: After generic identify, caps: afe9fbbf 00000000 00000000 00000000 00000180 00000000 00000000
    CPU: After vendor identify, caps: afe9fbbf 00000000 00000000 00000000 00000180 00000000 00000000
    CPU: L1 I cache: 32K, L1 D cache: 32K
    CPU: L2 cache: 2048K
    CPU: After all inits, caps: afe9fbbf 00000000 00000000 00000040 00000180 00000000 00000000
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    Compat vDSO mapped to ffffe000.
    CPU: Intel(R) Pentium(R) M processor 1.70GHz stepping 06
    Checking 'hlt' instruction... OK.
    ACPI: Core revision 20060707
    ENABLING IO-APIC IRQs
    ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
    NET: Registered protocol family 16
    ACPI: bus type pci registered
    PCI: Using configuration type 1
    Setting up standard PCI resources
    ACPI: Interpreter enabled
    ACPI: Using IOAPIC for interrupt routing
    ACPI: PCI Root Bridge [PCI0] (0000:00)
    PCI: Probing PCI hardware (bus 00)
    Boot video device is 0000:00:02.0
    PCI quirk: region e400-e47f claimed by ICH4 ACPI/GPIO/TCO
    PCI quirk: region ec00-ec3f claimed by ICH4 GPIO
    PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
    PCI: Transparent bridge - 0000:00:1e.0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
    ACPI: Embedded Controller [EC0] (gpe 28) interrupt mode.
    ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 11 12)
    ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 12) *0, disabled.
    ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 12)
    ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 12)
    ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 12) *0, disabled.
    ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 12) *0, disabled.
    ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 12) *0, disabled.
    ACPI: PCI Interrupt Link [LNKH] (IRQs 3 *4 5 6 7 12)
    ACPI: Power Resource [GFAN] (off)
    PCI: Using ACPI for IRQ routing
    PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
    PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
    PCI: Bus 2, cardbus bridge: 0000:01:03.0
    IO window: 0000c000-0000c0ff
    IO window: 0000c400-0000c4ff
    PREFETCH window: 22000000-23ffffff
    MEM window: 24000000-25ffffff
    PCI: Bus 6, cardbus bridge: 0000:01:03.1
    IO window: 0000cc00-0000ccff
    IO window: 00001000-000010ff
    PREFETCH window: 26000000-27ffffff
    MEM window: 28000000-29ffffff
    PCI: Bridge: 0000:00:1e.0
    IO window: c000-cfff
    MEM window: fe700000-fe8fffff
    PREFETCH window: de500000-de6fffff
    PCI: Setting latency timer of device 0000:00:1e.0 to 64
    ACPI: PCI Interrupt 0000:01:03.0[A] -> GSI 17 (level, low) -> IRQ 16
    ACPI: PCI Interrupt 0000:01:03.1[B] -> GSI 18 (level, low) -> IRQ 17
    PCI: Setting latency timer of device 0000:01:03.1 to 64
    NET: Registered protocol family 2
    IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
    TCP established hash table entries: 16384 (order: 4, 65536 bytes)
    TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
    TCP: Hash tables configured (established 16384 bind 8192)
    TCP reno registered
    audit: initializing netlink socket (disabled)
    audit(1153864808.431:1): initialized
    Coda Kernel/Venus communications, v6.0.0, coda@cs.cmu.edu
    Initializing Cryptographic API
    io scheduler noop registered
    io scheduler anticipatory registered (default)
    io scheduler deadline registered
    io scheduler cfq registered
    vesafb: framebuffer at 0xf0000000, mapped to 0xe0080000, using 6144k, total 8000k
    vesafb: mode is 1024x768x32, linelength=4096, pages=1
    vesafb: protected mode interface info at 00ff:44f0
    vesafb: scrolling: redraw
    vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
    Console: switching to colour frame buffer device 128x48
    fb0: VESA VGA frame buffer device
    Linux agpgart interface v0.101 (c) Dave Jones
    agpgart: Detected an Intel 855 Chipset.
    agpgart: Detected 8060K stolen memory.
    agpgart: AGP aperture is 128M @ 0xf0000000
    RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
    Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    ICH4: IDE controller at PCI slot 0000:00:1f.1
    PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
    ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 17
    ICH4: chipset revision 3
    ICH4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
    Probing IDE interface ide0...
    hda: TOSHIBA MK6026GAX, ATA DISK drive
    ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    Probing IDE interface ide1...
    hdc: TOSHIBA DVD-ROM SD-R2512, ATAPI CD/DVD-ROM drive
    ide1 at 0x170-0x177,0x376 on irq 15
    hda: max request size: 128KiB
    hda: 117210240 sectors (60011 MB), CHS=65535/16/63, UDMA(100)
    hda: cache flushes supported
    hda: hda1 hda2 hda3 < hda5 hda6 hda7 >
    i8042.c: Detected active multiplexing controller, rev 1.1.
    serio: i8042 AUX0 port at 0x60,0x64 irq 12
    serio: i8042 AUX1 port at 0x60,0x64 irq 12
    serio: i8042 AUX2 port at 0x60,0x64 irq 12
    serio: i8042 AUX3 port at 0x60,0x64 irq 12
    serio: i8042 KBD port at 0x60,0x64 irq 1
    mice: PS/2 mouse device common for all mice
    md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
    md: bitmap version 4.39
    device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
    TCP bic registered
    NET: Registered protocol family 1
    NET: Registered protocol family 10
    IPv6 over IPv4 tunneling driver
    NET: Registered protocol family 17
    Using IPI Shortcut mode
    ACPI: (supports S0 S1 S3 S4 S5)
    Time: tsc clocksource has been installed.
    md: Autodetecting RAID arrays.
    md: autorun ...
    md: ... autorun DONE.
    ReiserFS: hda5: found reiserfs format "3.6" with standard journal
    input: AT Translated Set 2 keyboard as /class/input/input0
    ReiserFS: hda5: using ordered data mode
    ReiserFS: hda5: journal params: device hda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
    ReiserFS: hda5: checking transaction log (hda5)
    ReiserFS: hda5: Using r5 hash to sort names
    VFS: Mounted root (reiserfs filesystem) readonly.
    Freeing unused kernel memory: 192k freed
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    device-mapper: table: 253:0: linear: dm-linear: Device lookup failed
    device-mapper: ioctl: error adding target to table
    Asus Laptop ACPI Extras version 0.30
    M2NE model detected, supported
    Registered led device: asus:mail
    Registered led device: asus:wireless
    ACPI: AC Adapter [AC0] (on-line)
    ACPI: Battery Slot [BAT0] (battery present)
    ACPI: Power Button (FF) [PWRF]
    ACPI: Sleep Button (CM) [SLPB]
    ACPI: Lid Switch [LID]
    ACPI: Transitioning device [FN00] to D3
    ACPI: Transitioning device [FN00] to D3
    ACPI: Fan [FN00] (off)
    ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
    ACPI: Processor [CPU1] (supports 8 throttling states)
    Time: acpi_pm clocksource has been installed.
    ACPI: Thermal Zone [THRM] (54 C)
    hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
    Uniform CD-ROM driver Revision: 3.20
    [drm] Initialized drm 1.0.1 20051102
    ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 18
    [drm] Initialized i915 1.5.0 20060119 on minor 0
    [drm] Initialized i915 1.5.0 20060119 on minor 1
    input: PC Speaker as /class/input/input1
    Synaptics Touchpad, model: 1, fw: 4.6, id: 0x925ea1, caps: 0x80471b/0x0
    input: SynPS/2 Synaptics TouchPad as /class/input/input2
    Yenta: CardBus bridge found at 0000:01:03.0 [1043:1754]
    Yenta: ISA IRQ mask 0x04b8, PCI irq 16
    Socket status: 30000006
    pcmcia: parent PCI bridge I/O window: 0xc000 - 0xcfff
    pcmcia: parent PCI bridge Memory window: 0xfe700000 - 0xfe8fffff
    pcmcia: parent PCI bridge Memory window: 0xde500000 - 0xde6fffff
    Yenta: CardBus bridge found at 0000:01:03.1 [1043:1754]
    Yenta: ISA IRQ mask 0x04b8, PCI irq 17
    Socket status: 30000006
    pcmcia: parent PCI bridge I/O window: 0xc000 - 0xcfff
    pcmcia: parent PCI bridge Memory window: 0xfe700000 - 0xfe8fffff
    pcmcia: parent PCI bridge Memory window: 0xde500000 - 0xde6fffff
    usbcore: registered new driver usbfs
    usbcore: registered new driver hub
    ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 19
    PCI: Setting latency timer of device 0000:00:1d.7 to 64
    ehci_hcd 0000:00:1d.7: EHCI Host Controller
    ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
    ehci_hcd 0000:00:1d.7: debug port 1
    PCI: cache line size of 32 is not supported by device 0000:00:1d.7
    ehci_hcd 0000:00:1d.7: irq 19, io mem 0xfebff800
    ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 6 ports detected
    USB Universal Host Controller Interface driver v3.0
    ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 18
    PCI: Setting latency timer of device 0000:00:1d.0 to 64
    uhci_hcd 0000:00:1d.0: UHCI Host Controller
    uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
    uhci_hcd 0000:00:1d.0: irq 18, io base 0x0000d480
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 20
    PCI: Setting latency timer of device 0000:00:1d.1 to 64
    uhci_hcd 0000:00:1d.1: UHCI Host Controller
    uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
    uhci_hcd 0000:00:1d.1: irq 20, io base 0x0000d800
    usb usb3: configuration #1 chosen from 1 choice
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 17
    PCI: Setting latency timer of device 0000:00:1d.2 to 64
    uhci_hcd 0000:00:1d.2: UHCI Host Controller
    uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
    uhci_hcd 0000:00:1d.2: irq 17, io base 0x0000d880
    usb usb4: configuration #1 chosen from 1 choice
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 2 ports detected
    8139too Fast Ethernet driver 0.9.27
    ACPI: PCI Interrupt 0000:01:04.0[A] -> GSI 16 (level, low) -> IRQ 18
    eth0: RealTek RTL8139 at 0xe06bc800, 00:11:2f:12:5a:dc, IRQ 18
    eth0: Identified 8139 chip type 'RTL-8101'
    tun: Universal TUN/TAP device driver, 1.6
    tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
    EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
    ReiserFS: dm-3: found reiserfs format "3.6" with standard journal
    ReiserFS: dm-3: using ordered data mode
    ReiserFS: dm-3: journal params: device dm-3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
    ReiserFS: dm-3: checking transaction log (dm-3)
    ReiserFS: dm-3: Using r5 hash to sort names
    ReiserFS: dm-2: found reiserfs format "3.6" with standard journal
    ReiserFS: dm-2: using ordered data mode
    ReiserFS: dm-2: journal params: device dm-2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
    ReiserFS: dm-2: checking transaction log (dm-2)
    ReiserFS: dm-2: Using r5 hash to sort names
    ReiserFS: dm-1: found reiserfs format "3.6" with standard journal
    ReiserFS: dm-1: using ordered data mode
    ReiserFS: dm-1: journal params: device dm-1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
    ReiserFS: dm-1: checking transaction log (dm-1)
    ReiserFS: dm-1: Using r5 hash to sort names
    ReiserFS: dm-0: found reiserfs format "3.6" with standard journal
    ReiserFS: dm-0: using ordered data mode
    ReiserFS: dm-0: journal params: device dm-0, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
    ReiserFS: dm-0: checking transaction log (dm-0)
    ReiserFS: dm-0: Using r5 hash to sort names
    Adding 1052248k swap on /dev/hda2. Priority:-1 extents:1 across:1052248k
    Real Time Clock Driver v1.12ac
    PCI: Enabling device 0000:00:1f.5 (0005 -> 0007)
    ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 16
    PCI: Setting latency timer of device 0000:00:1f.5 to 64
    intel8x0_measure_ac97_clock: measured 50314 usecs
    intel8x0: clocking to 48000
    ACPI: PCI Interrupt 0000:00:1f.6[B] -> GSI 17 (level, low) -> IRQ 16
    PCI: Setting latency timer of device 0000:00:1f.6 to 64
    i2c-core: driver [lm90] registered
    IA-32 Microcode Update Driver: v1.14a <tigran@veritas.com>
    microcode: CPU0 updated from revision 0x17 to 0x18, date = 10172004
    [unhandled content-type:application/pgp-signature]
    \
     
     \ /
      Last update: 2006-07-26 00:11    [W:0.051 / U:30.728 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site