lkml.org 
[lkml]   [2006]   [Jul]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    SubjectRe: skge error; hangs w/ hardware memory hole
    Andreas Kleen wrote:

    >
    > You need to use iommu=soft swiotlb=force
    >
    > The standard IOMMU is also broken on VIA, but forced swiotlb should
    > work.

    Didn't work :-(

    Excepts from the log:

    Bootdata ok (command line is BOOT_IMAGE=2.6.17-1-smp ro root=902
    iommu=soft swiotlb=force single)
    ...
    skge eth0: enabling interface
    skge 0000:00:0a.0: PCI error cmd=0x117 status=0x22b0
    skge unable to clear error (so ignoring them)
    skge eth0: Link is up at 1000 Mbps, full duplex, flow control tx and rx

    And then the NIC didn't work. Attaching full dmesg.

    Bootdata ok (command line is BOOT_IMAGE=2.6.17-1-smp ro root=902 iommu=soft swiotlb=force single)
    Linux version 2.6.17-1-amd64-k8-smp (Debian 2.6.17-2) (waldi@debian.org) (gcc version 4.1.2 20060613 (prerelease) (Debian 4.1.1-5)) #1 SMP Thu Jun 29 23:03:09 CEST 2006
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 00000000d7fb0000 (usable)
    BIOS-e820: 00000000d7fb0000 - 00000000d7fc0000 (ACPI data)
    BIOS-e820: 00000000d7fc0000 - 00000000d7ff0000 (ACPI NVS)
    BIOS-e820: 00000000d7ff0000 - 00000000d8000000 (reserved)
    BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
    BIOS-e820: 0000000100000000 - 0000000124000000 (usable)
    DMI 2.3 present.
    ACPI: RSDP (v002 ACPIAM ) @ 0x00000000000fa7c0
    ACPI: XSDT (v001 A M I OEMXSDT 0x10000506 MSFT 0x00000097) @ 0x00000000d7fb0100
    ACPI: FADT (v003 A M I OEMFACP 0x10000506 MSFT 0x00000097) @ 0x00000000d7fb0290
    ACPI: MADT (v001 A M I OEMAPIC 0x10000506 MSFT 0x00000097) @ 0x00000000d7fb0390
    ACPI: OEMB (v001 A M I OEMBIOS 0x10000506 MSFT 0x00000097) @ 0x00000000d7fc0040
    ACPI: DSDT (v001 A0036 A0036001 0x00000001 MSFT 0x0100000d) @ 0x0000000000000000
    Scanning NUMA topology in Northbridge 24
    Number of nodes 1
    Node 0 MemBase 0000000000000000 Limit 0000000124000000
    NUMA: Using 63 for the hash shift.
    Using node hash shift of 63
    Bootmem setup node 0 0000000000000000-0000000124000000
    On node 0 totalpages: 1014222
    DMA zone: 2502 pages, LIFO batch:0
    DMA32 zone: 866280 pages, LIFO batch:31
    Normal zone: 145440 pages, LIFO batch:31
    Looks like a VIA chipset. Disabling IOMMU. Override with "iommu=allowed"
    ACPI: PM-Timer IO Port: 0x808
    ACPI: Local APIC address 0xfee00000
    ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
    Processor #0 15:3 APIC version 16
    ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
    Processor #1 15:3 APIC version 16
    ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
    IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
    ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    ACPI: IRQ0 used by override.
    ACPI: IRQ2 used by override.
    ACPI: IRQ9 used by override.
    Setting APIC routing to physical flat
    Using ACPI (MADT) for SMP configuration information
    Allocating PCI resources starting at dc000000 (gap: d8000000:27780000)
    SMP: Allowing 2 CPUs, 0 hotplug CPUs
    Built 1 zonelists
    Kernel command line: BOOT_IMAGE=2.6.17-1-smp ro root=902 iommu=soft swiotlb=force single
    Initializing CPU#0
    PID hash table entries: 4096 (order: 12, 32768 bytes)
    Disabling vsyscall due to use of PM timer
    time.c: Using 3.579545 MHz WALL PM GTOD PM timer.
    time.c: Detected 2202.921 MHz processor.
    Console: colour VGA+ 80x25
    Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
    Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
    PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
    Placing software IO TLB between 0x163a000 - 0x563a000
    Memory: 3984540k/4784128k available (1870k kernel code, 143520k reserved, 820k data, 172k init)
    Calibrating delay using timer specific routine.. 4411.18 BogoMIPS (lpj=8822378)
    Security Framework v1.0.0 initialized
    SELinux: Disabled at boot.
    Capability LSM initialized
    Mount-cache hash table entries: 256
    CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
    CPU: L2 Cache: 1024K (64 bytes/line)
    CPU 0/0(2) -> Node 0 -> Core 0
    Using local APIC timer interrupts.
    result 12516619
    Detected 12.516 MHz APIC timer.
    Booting processor 1/2 APIC 0x1
    Initializing CPU#1
    Calibrating delay using timer specific routine.. 4405.96 BogoMIPS (lpj=8811936)
    CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
    CPU: L2 Cache: 1024K (64 bytes/line)
    CPU 1/1(2) -> Node 0 -> Core 1
    AMD Athlon(tm) 64 X2 Dual Core Processor 4400+ stepping 02
    CPU 1: Syncing TSC to CPU 0.
    CPU 1: synchronized TSC with CPU 0 (last diff -82 cycles, maxerr 637 cycles)
    Brought up 2 CPUs
    testing NMI watchdog ... OK.
    migration_cost=632
    checking if image is initramfs... it is
    Freeing initrd memory: 1348k freed
    NET: Registered protocol family 16
    ACPI: bus type pci registered
    PCI: Using configuration type 1
    ACPI: Subsystem revision 20060127
    ACPI: Interpreter enabled
    ACPI: Using IOAPIC for interrupt routing
    ACPI: PCI Root Bridge [PCI0] (0000:00)
    PCI: Probing PCI hardware (bus 00)
    PCI: Quirk-MSI-K8T Soundcard On
    PCI: Unexpected Value in PCI-Register: no Change!
    PCI: enabled onboard AC97/MC97 devices
    Boot video device is 0000:01:00.0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
    ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15)
    ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
    ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
    Linux Plug and Play Support v0.97 (c) Adam Belay
    pnp: PnP ACPI init
    pnp: ACPI device : hid PNP0A03
    pnp: ACPI device : hid PNP0200
    pnp: ACPI device : hid PNP0B00
    pnp: ACPI device : hid PNP0303
    pnp: ACPI device : hid PNP0F03
    pnp: ACPI device : hid PNP0800
    pnp: ACPI device : hid PNP0C04
    pnp: ACPI device : hid PNP0C02
    pnp: ACPI device : hid PNP0C02
    pnp: ACPI device : hid PNP0C02
    pnp: ACPI device : hid PNP0501
    pnp: ACPI device : hid PNP0501
    pnp: ACPI device : hid PNP0C01
    pnp: PnP ACPI: found 13 devices
    usbcore: registered new driver usbfs
    usbcore: registered new driver hub
    PCI: Using ACPI for IRQ routing
    PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
    TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
    agpgart: Detected AGP bridge 0
    agpgart: AGP aperture is 64M @ 0xdc000000
    pnp: the driver 'system' has been registered
    pnp: match found with the PnP device '00:07' and the driver 'system'
    pnp: 00:07: ioport range 0x680-0x6ff has been reserved
    pnp: 00:07: ioport range 0x290-0x297 has been reserved
    pnp: match found with the PnP device '00:08' and the driver 'system'
    pnp: match found with the PnP device '00:09' and the driver 'system'
    pnp: match found with the PnP device '00:0c' and the driver 'system'
    PCI: Bridge: 0000:00:01.0
    IO window: e000-efff
    MEM window: fbe00000-fbffffff
    PREFETCH window: e0000000-faffffff
    PCI: Setting latency timer of device 0000:00:01.0 to 64
    NET: Registered protocol family 2
    IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
    TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
    TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
    TCP: Hash tables configured (established 262144 bind 65536)
    TCP reno registered
    IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
    audit: initializing netlink socket (disabled)
    audit(1153618957.340:1): initialized
    VFS: Disk quotas dquot_6.5.1
    Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    Initializing Cryptographic API
    io scheduler noop registered
    io scheduler anticipatory registered (default)
    io scheduler deadline registered
    io scheduler cfq registered
    Real Time Clock Driver v1.12ac
    Linux agpgart interface v0.101 (c) Dave Jones
    Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
    serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
    pnp: the driver 'serial' has been registered
    pnp: match found with the PnP device '00:0a' and the driver 'serial'
    00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
    pnp: match found with the PnP device '00:0b' and the driver 'serial'
    00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
    usbmon: debugfs is not available
    pnp: the driver 'i8042 kbd' has been registered
    pnp: match found with the PnP device '00:03' and the driver 'i8042 kbd'
    pnp: the driver 'i8042 aux' has been registered
    pnp: match found with the PnP device '00:04' and the driver 'i8042 aux'
    PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
    serio: i8042 AUX port at 0x60,0x64 irq 12
    serio: i8042 KBD port at 0x60,0x64 irq 1
    mice: PS/2 mouse device common for all mice
    TCP bic registered
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    NET: Registered protocol family 8
    NET: Registered protocol family 20
    ACPI wakeup devices:
    PCI0 PS2K PS2M UAR2 UAR1 AC97 USB1 USB2 USB3 USB4 EHCI PWRB SLPB
    ACPI: (supports S0 S1 S3 S4 S5)
    Freeing unused kernel memory: 172k freed
    USB Universal Host Controller Interface driver v3.0
    GSI 16 sharing vector 0xA9 and IRQ 16
    ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 169
    PCI: VIA IRQ fixup for 0000:00:10.0, from 11 to 9
    uhci_hcd 0000:00:10.0: UHCI Host Controller
    uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
    uhci_hcd 0000:00:10.0: irq 169, io base 0x0000c400
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 2 ports detected
    input: AT Translated Set 2 keyboard as /class/input/input0
    ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 169
    PCI: VIA IRQ fixup for 0000:00:10.1, from 11 to 9
    uhci_hcd 0000:00:10.1: UHCI Host Controller
    uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
    uhci_hcd 0000:00:10.1: irq 169, io base 0x0000c800
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 169
    PCI: VIA IRQ fixup for 0000:00:10.2, from 10 to 9
    uhci_hcd 0000:00:10.2: UHCI Host Controller
    uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
    uhci_hcd 0000:00:10.2: irq 169, io base 0x0000d000
    usb usb3: configuration #1 chosen from 1 choice
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 169
    PCI: VIA IRQ fixup for 0000:00:10.3, from 10 to 9
    uhci_hcd 0000:00:10.3: UHCI Host Controller
    uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
    uhci_hcd 0000:00:10.3: irq 169, io base 0x0000d400
    usb usb4: configuration #1 chosen from 1 choice
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 2 ports detected
    usb 1-1: new full speed USB device using uhci_hcd and address 2
    ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 169
    ehci_hcd 0000:00:10.4: EHCI Host Controller
    ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
    ehci_hcd 0000:00:10.4: irq 169, io mem 0xfbd00000
    ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
    usb usb5: configuration #1 chosen from 1 choice
    hub 5-0:1.0: USB hub found
    hub 5-0:1.0: 8 ports detected
    usb 1-1: device not accepting address 2, error -71
    usbcore: registered new driver hiddev
    usb 1-1: new full speed USB device using uhci_hcd and address 4
    usb 1-1: configuration #1 chosen from 1 choice
    usb 1-2: new low speed USB device using uhci_hcd and address 5
    usb 1-2: configuration #1 chosen from 1 choice
    usb 2-2: new full speed USB device using uhci_hcd and address 2
    usb 2-2: configuration #1 chosen from 1 choice
    input: stereo-link stereo-link 1200 USB DAC as /class/input/input1
    input: USB HID v1.00 Device [stereo-link stereo-link 1200 USB DAC] on usb-0000:00:10.0-1
    hiddev96: USB HID v1.10 Device [American Power Conversion Back-UPS RS 1500 FW:8.g8 .D USB FW:g8 ] on usb-0000:00:10.0-2
    usbcore: registered new driver usbhid
    drivers/usb/input/hid-core.c: v2.6:USB HID core driver
    SCSI subsystem initialized
    libata version 1.20 loaded.
    sata_promise 0000:00:08.0: version 1.04
    GSI 17 sharing vector 0xB1 and IRQ 17
    ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 18 (level, low) -> IRQ 177
    ata1: SATA max UDMA/133 cmd 0xFFFFC20000006200 ctl 0xFFFFC20000006238 bmdma 0x0 irq 177
    ata2: SATA max UDMA/133 cmd 0xFFFFC20000006280 ctl 0xFFFFC200000062B8 bmdma 0x0 irq 177
    ata1: SATA link up 1.5 Gbps (SStatus 113)
    ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f
    ata1: dev 0 ATA-7, max UDMA/133, 390721968 sectors: LBA48
    ata1: dev 0 configured for UDMA/133
    scsi0 : sata_promise
    ata2: SATA link up 1.5 Gbps (SStatus 113)
    ata2: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f
    ata2: dev 0 ATA-7, max UDMA/133, 390721968 sectors: LBA48
    ata2: dev 0 configured for UDMA/133
    scsi1 : sata_promise
    Vendor: ATA Model: ST3200826AS Rev: 3.03
    Type: Direct-Access ANSI SCSI revision: 05
    Vendor: ATA Model: ST3200826AS Rev: 3.03
    Type: Direct-Access ANSI SCSI revision: 05
    SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
    sda: Write Protect is off
    sda: Mode Sense: 00 3a 00 00
    SCSI device sda: drive cache: write back
    SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
    sda: Write Protect is off
    sda: Mode Sense: 00 3a 00 00
    SCSI device sda: drive cache: write back
    sda: sda1 sda2 sda3 sda4
    sd 0:0:0:0: Attached scsi disk sda
    SCSI device sdb: 390721968 512-byte hdwr sectors (200050 MB)
    sdb: Write Protect is off
    sdb: Mode Sense: 00 3a 00 00
    SCSI device sdb: drive cache: write back
    SCSI device sdb: 390721968 512-byte hdwr sectors (200050 MB)
    sdb: Write Protect is off
    sdb: Mode Sense: 00 3a 00 00
    SCSI device sdb: drive cache: write back
    sdb: sdb1 sdb2 sdb3 sdb4
    sd 1:0:0:0: Attached scsi disk sdb
    md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
    md: bitmap version 4.39
    md: raid1 personality registered for level 1
    md: md2 stopped.
    md: bind<sdb3>
    md: bind<sda3>
    raid1: raid set md2 active with 2 out of 2 mirrors
    EXT3-fs: INFO: recovery required on readonly filesystem.
    EXT3-fs: write access will be enabled during recovery.
    kjournald starting. Commit interval 5 seconds
    EXT3-fs: md2: orphan cleanup on readonly fs
    ext3_orphan_cleanup: deleting unreferenced inode 3008056
    ext3_orphan_cleanup: deleting unreferenced inode 3008055
    ext3_orphan_cleanup: deleting unreferenced inode 2998284
    ext3_orphan_cleanup: deleting unreferenced inode 2998283
    ext3_orphan_cleanup: deleting unreferenced inode 2998281
    ext3_orphan_cleanup: deleting unreferenced inode 2998278
    ext3_orphan_cleanup: deleting unreferenced inode 2998277
    ext3_orphan_cleanup: deleting unreferenced inode 2998276
    EXT3-fs: md2: 8 orphan inodes deleted
    EXT3-fs: recovery complete.
    EXT3-fs: mounted filesystem with ordered data mode.
    Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    GSI 18 sharing vector 0xB9 and IRQ 18
    ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 185
    skge 1.5 addr 0xfbb00000 irq 185 chip Yukon-Lite rev 9
    skge eth0: addr 00:13:d4:21:77:e5
    VP_IDE: IDE controller at PCI slot 0000:00:0f.1
    GSI 19 sharing vector 0xC1 and IRQ 19
    ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 193
    PCI: VIA IRQ fixup for 0000:00:0f.1, from 255 to 1
    VP_IDE: chipset revision 6
    VP_IDE: not 100% native mode: will probe irqs later
    VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
    ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
    Probing IDE interface ide0...
    ieee1394: Initialized config rom entry `ip1394'
    pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    usbcore: registered new driver usbserial
    drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
    usbcore: registered new driver usbserial_generic
    drivers/usb/serial/usb-serial.c: USB Serial Driver core
    drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303
    pl2303 2-2:1.0: pl2303 converter detected
    usb 2-2: pl2303 converter now attached to ttyUSB0
    usbcore: registered new driver pl2303
    drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver
    usbcore: registered new driver snd-usb-audio
    Probing IDE interface ide1...
    input: PS/2 Generic Mouse as /class/input/input2
    hdc: TSSTcorpCD/DVDW TS-H552U, ATAPI CD/DVD-ROM drive
    ide1 at 0x170-0x177,0x376 on irq 15
    sata_via 0000:00:0f.0: version 1.1
    ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 193
    sata_via 0000:00:0f.0: routed to hard irq line 10
    ata3: SATA max UDMA/133 cmd 0xC000 ctl 0xB802 bmdma 0xA800 irq 193
    ata4: SATA max UDMA/133 cmd 0xB400 ctl 0xB002 bmdma 0xA808 irq 193
    ata3: SATA link down (SStatus 0)
    scsi2 : sata_via
    ata4: SATA link down (SStatus 0)
    scsi3 : sata_via
    shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    PCI: Enabling device 0000:00:11.6 (0000 -> 0001)
    GSI 20 sharing vector 0xC9 and IRQ 20
    ACPI: PCI Interrupt 0000:00:11.6[C] -> GSI 22 (level, low) -> IRQ 201
    PCI: Setting latency timer of device 0000:00:11.6 to 64
    VIA 82xx Modem: probe of 0000:00:11.6 failed with error -13
    ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 201
    PCI: Setting latency timer of device 0000:00:11.5 to 64
    GSI 21 sharing vector 0xD1 and IRQ 21
    ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 209
    ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[209] MMIO=[fb700000-fb7007ff] Max Packet=[2048] IR/IT contexts=[4/8]
    hdc: ATAPI 126X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
    Uniform CD-ROM driver Revision: 3.20
    ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d800003edb31]
    eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
    EXT3 FS on md2, internal journal
    Probing IDE interface ide0...
    powernow-k8: Found 2 AMD Athlon 64 / Opteron processors (version 1.60.2)
    powernow-k8: 0 : fid 0xe (2200 MHz), vid 0x8 (1350 mV)
    powernow-k8: 1 : fid 0xc (2000 MHz), vid 0xa (1300 mV)
    powernow-k8: 2 : fid 0xa (1800 MHz), vid 0xc (1250 mV)
    powernow-k8: 3 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
    cpu_init done, current fid 0xe, vid 0x8
    w83627hf 9191-0290: Reading VID from GPIO5
    device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@redhat.com
    md: md3 stopped.
    md: bind<sdb4>
    md: bind<sda4>
    md: raid0 personality registered for level 0
    md3: setting max_sectors to 128, segment boundary to 32767
    raid0: looking at sda4
    raid0: comparing sda4(35142080) with sda4(35142080)
    raid0: END
    raid0: ==> UNIQUE
    raid0: 1 zones
    raid0: looking at sdb4
    raid0: comparing sdb4(35142080) with sda4(35142080)
    raid0: EQUAL
    raid0: FINAL 1 zones
    raid0: done.
    raid0 : md_size is 70284160 blocks.
    raid0 : conf->hash_spacing is 70284160 blocks.
    raid0 : nb_zone is 1.
    raid0 : Allocating 8 bytes for hash.
    md: md1 stopped.
    md: bind<sdb2>
    md: bind<sda2>
    raid1: raid set md1 active with 2 out of 2 mirrors
    md: md0 stopped.
    md: bind<sdb1>
    md: bind<sda1>
    raid1: raid set md0 active with 2 out of 2 mirrors
    ReiserFS: md3: found reiserfs format "3.6" with standard journal
    ReiserFS: md3: using ordered data mode
    ReiserFS: md3: journal params: device md3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
    ReiserFS: md3: checking transaction log (md3)
    ReiserFS: md3: Using r5 hash to sort names
    Adding 3903672k swap on /dev/md1. Priority:-1 extents:1 across:3903672k
    skge eth0: enabling interface
    skge 0000:00:0a.0: PCI error cmd=0x117 status=0x22b0
    skge unable to clear error (so ignoring them)
    skge eth0: Link is up at 1000 Mbps, full duplex, flow control tx and rx
    \
     
     \ /
      Last update: 2006-07-23 08:35    [W:0.047 / U:60.332 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site