Messages in this thread | | | Date | Fri, 30 Jun 2006 08:14:20 +1000 | From | Nathan Scott <> | Subject | Re: BUG: held lock freed! with 2.6.17-mm3 and 2.6.17-mm4 |
| |
On Thu, Jun 29, 2006 at 10:38:09PM +0200, Ralf Hildebrandt wrote: > 2.6.17-mm3 and mm4 both report a "BUG: held lock freed!" while booting > up. Find the two dmesg outputs attached.
Thanks Ralf,
From the traces, looks like it happens during the unlinked inode list processing, just after log recovery (I assume you crashed / rebooted without unmounting before this boot?). Tim, do you see any situation in recovery where we might have freed an inode while it was locked? Not sure how the s_umount_key lock can be involved here, that may be a separate issue.
cheers.
> ========================= > [ BUG: held lock freed! ] > ------------------------- > init/1 is freeing memory dbab7750-dbab77e3, with a lock still held there! > 3 locks held by init/1: > #0: (&type->s_umount_key#13){--..}, at: [<c0167961>] sget+0x1b1/0x350 > #1: (&(&ip->i_iolock)->mr_lock){--..}, at: [<c01cf011>] xfs_ilock+0xa1/0xb0 > #2: (&(&ip->i_lock)->mr_lock){--..}, at: [<c01cefed>] xfs_ilock+0x7d/0xb0 > > -- > Ralf Hildebrandt (i.A. des IT-Zentrums) Ralf.Hildebrandt@charite.de > Charite - Universitätsmedizin Berlin Tel. +49 (0)30-450 570-155 > Gemeinsame Einrichtung von FU- und HU-Berlin Fax. +49 (0)30-450 570-962 > IT-Zentrum Standort CBF send no mail to spamtrap@charite.de
> level) > ACPI: IRQ0 used by override. > ACPI: IRQ2 used by override. > Enabling APIC mode: Flat. Using 1 I/O APICs > Using ACPI (MADT) for SMP configuration information > Allocating PCI resources starting at 30000000 (gap: 20000000:dff80000) > Detected 1591.934 MHz processor. > Built 1 zonelists. Total pages: 114496 > Kernel command line: auto BOOT_IMAGE=Linux ro root=301 hdc=noprobe hdc=cdrom video=vesafb:ywrap,mtrr:4 pci=assign-busses lapic panic=15 > ide_setup: hdc=noprobe > ide_setup: hdc=cdrom > mapped APIC to ffffd000 (fee00000) > mapped IOAPIC to ffffc000 (fec00000) > Enabling fast FPU save and restore... done. > Enabling unmasked SIMD FPU exception support... done. > Initializing CPU#0 > CPU 0 irqstacks, hard=c03f1000 soft=c03f0000 > PID hash table entries: 2048 (order: 11, 8192 bytes) > Console: colour dummy device 80x25 > Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar > ... MAX_LOCKDEP_SUBCLASSES: 8 > ... MAX_LOCK_DEPTH: 30 > ... MAX_LOCKDEP_KEYS: 2048 > ... CLASSHASH_SIZE: 1024 > ... MAX_LOCKDEP_ENTRIES: 8192 > ... MAX_LOCKDEP_CHAINS: 8192 > ... CHAINHASH_SIZE: 4096 > memory used by lock dependency info: 696 kB > per task-struct memory footprint: 1200 bytes > Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) > Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) > Memory: 449036k/457984k available (2016k kernel code, 8508k reserved, 766k data, 200k init, 0k highmem) > Checking if this processor honours the WP bit even in supervisor mode... Ok. > Calibrating delay using timer specific routine.. 3187.75 BogoMIPS (lpj=6375500) > Mount-cache hash table entries: 512 > CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001 > CPU: After vendor identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001 > CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) > CPU: L2 Cache: 1024K (64 bytes/line) > CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000001 00000000 00000001 > Intel machine check architecture supported. > Intel machine check reporting enabled on CPU#0. > Compat vDSO mapped to ffffe000. > CPU: AMD Turion(tm) 64 Mobile Technology ML-30 stepping 02 > Checking 'hlt' instruction... OK. > SMP alternatives: switching to UP code > Freeing SMP alternatives: 0k freed > ACPI: Core revision 20060608 > ENABLING IO-APIC IRQs > ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 > ..MP-BIOS bug: 8254 timer not connected to IO-APIC > ...trying to set up timer (IRQ0) through the 8259A ... failed. > ...trying to set up timer as Virtual Wire IRQ... works. > NET: Registered protocol family 16 > ACPI: bus type pci registered > PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved > PCI: Not using MMCONFIG. > PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1 > Setting up standard PCI resources > ACPI: Interpreter enabled > ACPI: Using IOAPIC for interrupt routing > ACPI: PCI Root Bridge [PCI0] (0000:00) > PCI: Probing PCI hardware (bus 00) > PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1 > Boot video device is 0000:01:05.0 > PCI: Transparent bridge - 0000:00:14.4 > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] > ACPI: Embedded Controller [EC] (gpe 6) interrupt mode. > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.POP2._PRT] > ACPI: PCI Interrupt Link [LNKA] (IRQs 5 6 7 10 11 12 14 15) *0, disabled. > ACPI: PCI Interrupt Link [LNKB] (IRQs 5 6 7 *10 11 12 14 15) > ACPI: PCI Interrupt Link [LNKC] (IRQs *5 6 7 10 11 12 14 15) > ACPI: PCI Interrupt Link [LNKD] (IRQs 5 6 7 10 *11 12 14 15) > ACPI: PCI Interrupt Link [LNKE] (IRQs 5 *6 7 10 11 12 14 15) > ACPI: PCI Interrupt Link [LNKF] (IRQs 5 6 *7 10 11 12 14 15) > ACPI: PCI Interrupt Link [LNKG] (IRQs *5 6 7 10 11 12 14 15) > ACPI: PCI Interrupt Link [LNKH] (IRQs 5 6 7 10 11 12 14 15) *0, disabled. > Linux Plug and Play Support v0.97 (c) Adam Belay > pnp: PnP ACPI init > pnp: PnP ACPI: found 11 devices > PCI: Using ACPI for IRQ routing > PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report > PCI: Device 0000:02:03.0 not found by BIOS > PCI: Device 0000:02:04.0 not found by BIOS > PCI: Device 0000:02:04.1 not found by BIOS > PCI: Device 0000:02:04.2 not found by BIOS > PCI: Device 0000:02:09.0 not found by BIOS > PCI: Bridge: 0000:00:01.0 > IO window: d000-dfff > MEM window: fbe00000-fbefffff > PREFETCH window: f0000000-faffffff > PCI: Bus 3, cardbus bridge: 0000:02:04.0 > IO window: 0000e000-0000e0ff > IO window: 0000e400-0000e4ff > PREFETCH window: 30000000-31ffffff > MEM window: 36000000-37ffffff > PCI: Bus 7, cardbus bridge: 0000:02:04.1 > IO window: 0000ec00-0000ecff > IO window: 00001000-000010ff > PREFETCH window: 32000000-33ffffff > MEM window: 38000000-39ffffff > PCI: Bridge: 0000:00:14.4 > IO window: e000-efff > MEM window: fbf00000-fbffffff > PREFETCH window: 30000000-34ffffff > ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 19 (level, low) -> IRQ 16 > ACPI: PCI Interrupt 0000:02:04.1[B] -> GSI 20 (level, low) -> IRQ 17 > NET: Registered protocol family 2 > IP route cache hash table entries: 4096 (order: 2, 16384 bytes) > TCP established hash table entries: 16384 (order: 8, 1572864 bytes) > TCP bind hash table entries: 8192 (order: 7, 819200 bytes) > TCP: Hash tables configured (established 16384 bind 8192) > TCP reno registered > SGI XFS with no debug enabled > Initializing Cryptographic API > io scheduler noop registered > io scheduler anticipatory registered > io scheduler deadline registered > io scheduler cfq registered (default) > vesafb: framebuffer at 0xf0000000, mapped to 0xdc880000, using 3072k, total 65536k > vesafb: mode is 1024x768x16, linelength=2048, pages=41 > vesafb: protected mode interface info at c000:52f9 > vesafb: pmi: set display start = c00c5367, set palette = c00c53a1 > vesafb: pmi: ports = d810 d816 d854 d838 d83c d85c d800 d804 d8b0 d8b2 d8b4 > vesafb: scrolling: ywrap using protected mode interface, yres_virtual=1536 > vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 > Console: switching to colour frame buffer device 128x48 > fb0: VESA VGA frame buffer device > lp: driver loaded but no devices found > RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize > Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 > ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx > ATIIXP: IDE controller at PCI slot 0000:00:14.1 > ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 18 > ATIIXP: chipset revision 0 > ATIIXP: not 100% native mode: will probe irqs later > ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:pio > ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:pio > Probing IDE interface ide0... > hda: WDC WD600VE-00HDT0, ATA DISK drive > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 > Probing IDE interface ide1... > ide1 at 0x170-0x177,0x376 on irq 15 > hda: max request size: 128KiB > hda: 117210240 sectors (60011 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100) > hda: cache flushes supported > hda: hda1 hda2 < hda5 > > PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 > i8042.c: Detected active multiplexing controller, rev 1.1. > serio: i8042 AUX0 port at 0x60,0x64 irq 12 > serio: i8042 AUX1 port at 0x60,0x64 irq 12 > serio: i8042 AUX2 port at 0x60,0x64 irq 12 > serio: i8042 AUX3 port at 0x60,0x64 irq 12 > serio: i8042 KBD port at 0x60,0x64 irq 1 > mice: PS/2 mouse device common for all mice > TCP bic registered > Using IPI Shortcut mode > ACPI: (supports S0 S1 S3 S4 S5) > Time: tsc clocksource has been installed. > Freeing unused kernel memory: 200k freed > XFS mounting filesystem hda1 > Starting XFS recovery on filesystem: hda1 (logdev: internal) > input: AT Translated Set 2 keyboard as /class/input/input0 > > ========================= > [ BUG: held lock freed! ] > ------------------------- > init/1 is freeing memory dbe68750-dbe687e3, with a lock still held there! > 3 locks held by init/1: > #0: (&type->s_umount_key#13){--..}, at: [<c0166bd1>] sget+0x1b1/0x350 > #1: (&(&ip->i_iolock)->mr_lock){--..}, at: [<c01cd161>] xfs_ilock+0xa1/0xb0 > #2: (&(&ip->i_lock)->mr_lock){--..}, at: [<c01cd13d>] xfs_ilock+0x7d/0xb0 > > stack backtrace: > [<c0104192>] show_trace+0x12/0x20 > [<c0104859>] dump_stack+0x19/0x20 > [<c0135434>] debug_check_no_locks_freed+0x154/0x170 > [<c0216c81>] __init_rwsem+0x21/0x60 > [<c01cd495>] xfs_inode_lock_init+0x25/0xe0 > [<c01cdaca>] xfs_iget+0x17a/0x59a > [<c01ddc16>] xlog_recover_process_iunlinks+0x316/0x500 > [<c01de0c8>] xlog_recover_finish+0x2c8/0x380 > [<c01d9b07>] xfs_log_mount_finish+0x37/0x50 > [<c01e26a2>] xfs_mountfs+0xe52/0x1020 > [<c01d40b9>] xfs_ioinit+0x29/0x40 > [<c01e9afd>] xfs_mount+0x66d/0xa20 > [<c01fc415>] vfs_mount+0x25/0x30 > [<c01fc236>] xfs_fs_fill_super+0x76/0x1e0 > [<c0167516>] get_sb_bdev+0xf6/0x130 > [<c01fb3b1>] xfs_fs_get_sb+0x21/0x30 > [<c0167010>] vfs_kern_mount+0x40/0xa0 > [<c01670c6>] do_kern_mount+0x36/0x50 > [<c017d712>] do_mount+0x232/0x610 > [<c017db5f>] sys_mount+0x6f/0xb0 > [<c01030db>] syscall_call+0x7/0xb > Ending XFS recovery on filesystem: hda1 (logdev: internal) > NET: Registered protocol family 1 > Yenta: CardBus bridge found at 0000:02:04.0 [1462:0131] > Yenta: ISA IRQ mask 0x0cb8, PCI irq 16 > Socket status: 30000006 > pcmcia: parent PCI bridge I/O window: 0xe000 - 0xefff > cs: IO port probe 0xe000-0xefff: clean. > pcmcia: parent PCI bridge Memory window: 0xfbf00000 - 0xfbffffff > pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x34ffffff > Yenta: CardBus bridge found at 0000:02:04.1 [1462:0131] > Synaptics Touchpad, model: 1, fw: 5.9, id: 0x116eb1, caps: 0xa04713/0x0 > Yenta: ISA IRQ mask 0x0cb8, PCI irq 17 > Socket status: 30000006 > pcmcia: parent PCI bridge I/O window: 0xe000 - 0xefff > cs: IO port probe 0xe000-0xefff: clean. > pcmcia: parent PCI bridge Memory window: 0xfbf00000 - 0xfbffffff > pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x34ffffff > ACPI: PCI Interrupt 0000:02:09.0[A] -> GSI 22 (level, low) -> IRQ 19 > rt2500 1.1.0 CVS 2005/07/10 http://rt2x00.serialmonkey.com > 8139too Fast Ethernet driver 0.9.27 > ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 18 (level, low) -> IRQ 20 > eth1: RealTek RTL8139 at 0xdcb92c00, 00:10:dc:e8:c8:4f, IRQ 20 > eth1: Identified 8139 chip type 'RTL-8101' > input: SynPS/2 Synaptics TouchPad as /class/input/input1 > psmouse.c: TouchPad at isa0060/serio2/input0 lost sync at byte 1 > piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device > usbcore: registered new driver usbfs > usbcore: registered new driver hub > hdc: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache > Uniform CD-ROM driver Revision: 3.20 > Linux agpgart interface v0.101 (c) Dave Jones > ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 17 (level, low) -> IRQ 22 > hda: cache flushes supported > ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 16 > ehci_hcd 0000:00:13.2: EHCI Host Controller > ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 1 > ehci_hcd 0000:00:13.2: irq 16, io mem 0xfbdff000 > ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 > usb usb1: new device found, idVendor=0000, idProduct=0000 > usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb1: Product: EHCI Host Controller > usb usb1: Manufacturer: Linux 2.6.17-mm3 ehci_hcd > usb usb1: SerialNumber: 0000:00:13.2 > usb usb1: configuration #1 chosen from 1 choice > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 8 ports detected > ohci_hcd: 2006 May 24 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) > ts: Compaq touchscreen protocol output > ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 16 > ohci_hcd 0000:00:13.0: OHCI Host Controller > ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2 > ohci_hcd 0000:00:13.0: irq 16, io mem 0xfbdfd000 > usb usb2: new device found, idVendor=0000, idProduct=0000 > usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb2: Product: OHCI Host Controller > usb usb2: Manufacturer: Linux 2.6.17-mm3 ohci_hcd > usb usb2: SerialNumber: 0000:00:13.0 > usb usb2: configuration #1 chosen from 1 choice > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 4 ports detected > Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled > ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 16 > ohci_hcd 0000:00:13.1: OHCI Host Controller > ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3 > ohci_hcd 0000:00:13.1: irq 16, io mem 0xfbdfe000 > usb usb3: new device found, idVendor=0000, idProduct=0000 > usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb3: Product: OHCI Host Controller > usb usb3: Manufacturer: Linux 2.6.17-mm3 ohci_hcd > usb usb3: SerialNumber: 0000:00:13.1 > usb usb3: configuration #1 chosen from 1 choice > hub 3-0:1.0: USB hub found > hub 3-0:1.0: 4 ports detected > ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 17 (level, low) -> IRQ 22 > usb 3-1: new low speed USB device using ohci_hcd and address 2 > cs: IO port probe 0x100-0x4ff: excluding 0x408-0x40f 0x4d0-0x4d7 > cs: IO port probe 0x800-0x8ff: clean. > cs: IO port probe 0xc00-0xcff: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcdf 0xcf8-0xcff > cs: IO port probe 0xa00-0xaff: clean. > cs: IO port probe 0x100-0x4ff: excluding 0x408-0x40f 0x4d0-0x4d7 > cs: IO port probe 0x800-0x8ff: clean. > cs: IO port probe 0xc00-0xcff: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcdf 0xcf8-0xcff > cs: IO port probe 0xa00-0xaff: clean. > usb 3-1: new device found, idVendor=046d, idProduct=c00c > usb 3-1: new device strings: Mfr=1, Product=2, SerialNumber=0 > usb 3-1: Product: USB Optical Mouse > usb 3-1: Manufacturer: Logitech > usb 3-1: configuration #1 chosen from 1 choice > input: Logitech USB Optical Mouse as /class/input/input2 > usbcore: registered new driver usbmouse > drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver > usbcore: registered new driver hiddev > usbcore: registered new driver usbhid > drivers/usb/input/hid-core.c: v2.6:USB HID core driver > hda: cache flushes supported > Adding 1349420k swap on /dev/hda5. Priority:-1 extents:1 across:1349420k > Linux video capture interface: v2.00 > saa7130/34: v4l2 driver version 0.2.14 loaded > pcmcia: Detected deprecated PCMCIA ioctl usage from process: discover. > pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools. > pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details. > NET: Registered protocol family 17 > ACPI: Battery Slot [BAT1] (battery present) > ACPI: AC Adapter [ADP1] (on-line) > ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) > ACPI: Power Button (FF) [PWRF] > ACPI: Lid Switch [LID0] > ACPI: Sleep Button (CM) [SLPB] > ACPI: Power Button (CM) [PWRB] > Time: acpi_pm clocksource has been installed. > ACPI: Thermal Zone [THRM] (64 C) > powernow-k8: Found 1 AMD Turion(tm) 64 Mobile Technology ML-30 processors (version 2.00.00) > powernow-k8: 0 : fid 0x0 (800 MHz), vid 0x12 > powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0x4 > powernow-k8: ph2 null fid transition 0x8 > [drm] Initialized drm 1.0.1 20051102 > APIC error on CPU0: 00(40) > APIC error on CPU0: 40(40) > APIC error on CPU0: 40(40) > APIC error on CPU0: 40(40) > APIC error on CPU0: 40(40) > APIC error on CPU0: 40(40) > APIC error on CPU0: 40(40) > APIC error on CPU0: 40(40) > APIC error on CPU0: 40(40) > APIC error on CPU0: 40(40) > APIC error on CPU0: 40(40) > APIC error on CPU0: 40(40) > APIC error on CPU0: 40(40) > APIC error on CPU0: 40(40) > APIC error on CPU0: 40(40) > APIC error on CPU0: 40(40) > APIC error on CPU0: 40(40) > APIC error on CPU0: 40(40) > psmouse.c: TouchPad at isa0060/serio2/input0 - driver resynched. > APIC error on CPU0: 40(40)
> 0x08242005 MSFT 0x00000097) @ 0x1bf40200 > ACPI: MADT (v001 MSI OEMAPIC 0x08242005 MSFT 0x00000097) @ 0x1bf40300 > ACPI: WDRT (v001 MSI MSI_OEM 0x08242005 MSFT 0x00000097) @ 0x1bf40360 > ACPI: MCFG (v001 MSI OEMMCFG 0x08242005 MSFT 0x00000097) @ 0x1bf403b0 > ACPI: SSDT (v001 OEM_ID OEMTBLID 0x00000001 INTL 0x02002026) @ 0x1bf43620 > ACPI: OEMB (v001 MSI MSI_OEM 0x08242005 MSFT 0x00000097) @ 0x1bf50040 > ACPI: DSDT (v001 MSI 1013 0x08242005 INTL 0x02002026) @ 0x00000000 > ATI board detected. Disabling timer routing over 8254. > ACPI: PM-Timer IO Port: 0x4008 > ACPI: Local APIC address 0xfee00000 > ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) > Processor #0 15:4 APIC version 16 > ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) > IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, GSI 0-23 > ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) > ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level) > ACPI: IRQ0 used by override. > ACPI: IRQ2 used by override. > Enabling APIC mode: Flat. Using 1 I/O APICs > Using ACPI (MADT) for SMP configuration information > Allocating PCI resources starting at 30000000 (gap: 20000000:dff80000) > Detected 1592.032 MHz processor. > Built 1 zonelists. Total pages: 114496 > Kernel command line: BOOT_IMAGE=Linux ro root=301 hdc=noprobe hdc=cdrom video=vesafb:ywrap,mtrr:4 pci=assign-busses lapic panic=15 > ide_setup: hdc=noprobe > ide_setup: hdc=cdrom > mapped APIC to ffffd000 (fee00000) > mapped IOAPIC to ffffc000 (fec00000) > Enabling fast FPU save and restore... done. > Enabling unmasked SIMD FPU exception support... done. > Initializing CPU#0 > CPU 0 irqstacks, hard=c03f6000 soft=c03f5000 > PID hash table entries: 2048 (order: 11, 8192 bytes) > Console: colour dummy device 80x25 > Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar > ... MAX_LOCKDEP_SUBCLASSES: 8 > ... MAX_LOCK_DEPTH: 30 > ... MAX_LOCKDEP_KEYS: 2048 > ... CLASSHASH_SIZE: 1024 > ... MAX_LOCKDEP_ENTRIES: 8192 > ... MAX_LOCKDEP_CHAINS: 8192 > ... CHAINHASH_SIZE: 4096 > memory used by lock dependency info: 696 kB > per task-struct memory footprint: 1200 bytes > Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) > Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) > Memory: 449016k/457984k available (2034k kernel code, 8528k reserved, 769k data, 200k init, 0k highmem) > Checking if this processor honours the WP bit even in supervisor mode... Ok. > Calibrating delay using timer specific routine.. 3187.58 BogoMIPS (lpj=6375170) > Mount-cache hash table entries: 512 > CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001 > CPU: After vendor identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001 > CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) > CPU: L2 Cache: 1024K (64 bytes/line) > CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000001 00000000 00000001 > Intel machine check architecture supported. > Intel machine check reporting enabled on CPU#0. > Compat vDSO mapped to ffffe000. > CPU: AMD Turion(tm) 64 Mobile Technology ML-30 stepping 02 > Checking 'hlt' instruction... OK. > ACPI: Core revision 20060623 > ENABLING IO-APIC IRQs > ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 > ..MP-BIOS bug: 8254 timer not connected to IO-APIC > ...trying to set up timer (IRQ0) through the 8259A ... failed. > ...trying to set up timer as Virtual Wire IRQ... works. > NET: Registered protocol family 16 > ACPI: bus type pci registered > PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved > PCI: Not using MMCONFIG. > PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1 > Setting up standard PCI resources > ACPI: Interpreter enabled > ACPI: Using IOAPIC for interrupt routing > ACPI: PCI Root Bridge [PCI0] (0000:00) > PCI: Probing PCI hardware (bus 00) > PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1 > Boot video device is 0000:01:05.0 > PCI: Transparent bridge - 0000:00:14.4 > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] > ACPI: Embedded Controller [EC] (gpe 6) interrupt mode. > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.POP2._PRT] > ACPI: PCI Interrupt Link [LNKA] (IRQs 5 6 7 10 11 12 14 15) *0, disabled. > ACPI: PCI Interrupt Link [LNKB] (IRQs 5 6 7 *10 11 12 14 15) > ACPI: PCI Interrupt Link [LNKC] (IRQs *5 6 7 10 11 12 14 15) > ACPI: PCI Interrupt Link [LNKD] (IRQs 5 6 7 10 *11 12 14 15) > ACPI: PCI Interrupt Link [LNKE] (IRQs 5 *6 7 10 11 12 14 15) > ACPI: PCI Interrupt Link [LNKF] (IRQs 5 6 *7 10 11 12 14 15) > ACPI: PCI Interrupt Link [LNKG] (IRQs *5 6 7 10 11 12 14 15) > ACPI: PCI Interrupt Link [LNKH] (IRQs 5 6 7 10 11 12 14 15) *0, disabled. > Linux Plug and Play Support v0.97 (c) Adam Belay > pnp: PnP ACPI init > pnp: PnP ACPI: found 11 devices > PCI: Using ACPI for IRQ routing > PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report > PCI: Device 0000:02:03.0 not found by BIOS > PCI: Device 0000:02:04.0 not found by BIOS > PCI: Device 0000:02:04.1 not found by BIOS > PCI: Device 0000:02:04.2 not found by BIOS > PCI: Device 0000:02:09.0 not found by BIOS > PCI: Bridge: 0000:00:01.0 > IO window: d000-dfff > MEM window: fbe00000-fbefffff > PREFETCH window: f0000000-faffffff > PCI: Bus 3, cardbus bridge: 0000:02:04.0 > IO window: 0000e000-0000e0ff > IO window: 0000e400-0000e4ff > PREFETCH window: 30000000-31ffffff > MEM window: 36000000-37ffffff > PCI: Bus 7, cardbus bridge: 0000:02:04.1 > IO window: 0000ec00-0000ecff > IO window: 00001000-000010ff > PREFETCH window: 32000000-33ffffff > MEM window: 38000000-39ffffff > PCI: Bridge: 0000:00:14.4 > IO window: e000-efff > MEM window: fbf00000-fbffffff > PREFETCH window: 30000000-34ffffff > Device `[CBC0]' is not power manageable<6>ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 19 (level, low) -> IRQ 16 > Device `[CBC1]' is not power manageable<6>ACPI: PCI Interrupt 0000:02:04.1[B] -> GSI 20 (level, low) -> IRQ 17 > NET: Registered protocol family 2 > IP route cache hash table entries: 4096 (order: 2, 16384 bytes) > TCP established hash table entries: 16384 (order: 8, 1572864 bytes) > TCP bind hash table entries: 8192 (order: 7, 819200 bytes) > TCP: Hash tables configured (established 16384 bind 8192) > TCP reno registered > SGI XFS with no debug enabled > Initializing Cryptographic API > io scheduler noop registered > io scheduler anticipatory registered > io scheduler deadline registered > io scheduler cfq registered (default) > vesafb: framebuffer at 0xf0000000, mapped to 0xdc880000, using 3072k, total 65536k > vesafb: mode is 1024x768x16, linelength=2048, pages=41 > vesafb: protected mode interface info at c000:52f9 > vesafb: pmi: set display start = c00c5367, set palette = c00c53a1 > vesafb: pmi: ports = d810 d816 d854 d838 d83c d85c d800 d804 d8b0 d8b2 d8b4 > vesafb: scrolling: ywrap using protected mode interface, yres_virtual=1536 > vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 > Console: switching to colour frame buffer device 128x48 > fb0: VESA VGA frame buffer device > lp: driver loaded but no devices found > RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize > Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 > ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx > ATIIXP: IDE controller at PCI slot 0000:00:14.1 > ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 18 > ATIIXP: chipset revision 0 > ATIIXP: not 100% native mode: will probe irqs later > ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:pio > ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:pio > Probing IDE interface ide0... > hda: WDC WD600VE-00HDT0, ATA DISK drive > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 > Probing IDE interface ide1... > ide1 at 0x170-0x177,0x376 on irq 15 > hda: max request size: 128KiB > hda: 117210240 sectors (60011 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100) > hda: cache flushes supported > hda: hda1 hda2 < hda5 > > PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 > i8042.c: Detected active multiplexing controller, rev 1.1. > serio: i8042 AUX0 port at 0x60,0x64 irq 12 > serio: i8042 AUX1 port at 0x60,0x64 irq 12 > serio: i8042 AUX2 port at 0x60,0x64 irq 12 > serio: i8042 AUX3 port at 0x60,0x64 irq 12 > serio: i8042 KBD port at 0x60,0x64 irq 1 > mice: PS/2 mouse device common for all mice > TCP bic registered > Using IPI Shortcut mode > ACPI: (supports S0 S1 S3 S4 S5) > Time: tsc clocksource has been installed. > Freeing unused kernel memory: 200k freed > XFS mounting filesystem hda1 > Starting XFS recovery on filesystem: hda1 (logdev: internal) > input: AT Translated Set 2 keyboard as /class/input/input0 > > ========================= > [ BUG: held lock freed! ] > ------------------------- > init/1 is freeing memory dbab7750-dbab77e3, with a lock still held there! > 3 locks held by init/1: > #0: (&type->s_umount_key#13){--..}, at: [<c0167961>] sget+0x1b1/0x350 > #1: (&(&ip->i_iolock)->mr_lock){--..}, at: [<c01cf011>] xfs_ilock+0xa1/0xb0 > #2: (&(&ip->i_lock)->mr_lock){--..}, at: [<c01cefed>] xfs_ilock+0x7d/0xb0 > > stack backtrace: > [<c0104192>] show_trace+0x12/0x20 > [<c0104859>] dump_stack+0x19/0x20 > [<c0135b24>] debug_check_no_locks_freed+0x154/0x170 > [<c0218da1>] __init_rwsem+0x21/0x60 > [<c01cf345>] xfs_inode_lock_init+0x25/0xe0 > [<c01cf97a>] xfs_iget+0x17a/0x59a > [<c01dfad6>] xlog_recover_process_iunlinks+0x316/0x500 > [<c01dff88>] xlog_recover_finish+0x2c8/0x380 > [<c01db9c7>] xfs_log_mount_finish+0x37/0x50 > [<c01e4532>] xfs_mountfs+0xe52/0x1020 > [<c01d5f89>] xfs_ioinit+0x29/0x40 > [<c01eb98d>] xfs_mount+0x66d/0xa20 > [<c01fe365>] vfs_mount+0x25/0x30 > [<c01fe186>] xfs_fs_fill_super+0x76/0x1e0 > [<c0168296>] get_sb_bdev+0xf6/0x130 > [<c01fd301>] xfs_fs_get_sb+0x21/0x30 > [<c0167d90>] vfs_kern_mount+0x40/0xa0 > [<c0167e46>] do_kern_mount+0x36/0x50 > [<c017ecfe>] do_mount+0x27e/0x6d0 > [<c017f1bf>] sys_mount+0x6f/0xb0 > [<c01030db>] syscall_call+0x7/0xb > Ending XFS recovery on filesystem: hda1 (logdev: internal) > NET: Registered protocol family 1 > Yenta: CardBus bridge found at 0000:02:04.0 [1462:0131] > Yenta: ISA IRQ mask 0x0cb8, PCI irq 16 > Socket status: 30000006 > pcmcia: parent PCI bridge I/O window: 0xe000 - 0xefff > cs: IO port probe 0xe000-0xefff: clean. > pcmcia: parent PCI bridge Memory window: 0xfbf00000 - 0xfbffffff > pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x34ffffff > Yenta: CardBus bridge found at 0000:02:04.1 [1462:0131] > Yenta: ISA IRQ mask 0x0cb8, PCI irq 17 > Socket status: 30000006 > pcmcia: parent PCI bridge I/O window: 0xe000 - 0xefff > cs: IO port probe 0xe000-0xefff: clean. > pcmcia: parent PCI bridge Memory window: 0xfbf00000 - 0xfbffffff > pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x34ffffff > 8139too Fast Ethernet driver 0.9.27 > Device `[RTL]' is not power manageable<6>ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 18 (level, low) -> IRQ 19 > eth0: RealTek RTL8139 at 0xdc87ec00, 00:10:dc:e8:c8:4f, IRQ 19 > eth0: Identified 8139 chip type 'RTL-8101' > ACPI: PCI Interrupt 0000:02:09.0[A] -> GSI 22 (level, low) -> IRQ 20 > rt2500 1.1.0 CVS 2005/07/10 http://rt2x00.serialmonkey.com > hdc: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache > Uniform CD-ROM driver Revision: 3.20 > Synaptics Touchpad, model: 1, fw: 5.9, id: 0x116eb1, caps: 0xa04713/0x0 > input: SynPS/2 Synaptics TouchPad as /class/input/input1 > psmouse.c: TouchPad at isa0060/serio2/input0 lost sync at byte 1 > usbcore: registered new driver usbfs > usbcore: registered new driver hub > piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device > ohci_hcd: 2006 May 24 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) > ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 16 > ohci_hcd 0000:00:13.0: OHCI Host Controller > ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1 > ohci_hcd 0000:00:13.0: irq 16, io mem 0xfbdfd000 > ts: Compaq touchscreen protocol output > usb usb1: new device found, idVendor=0000, idProduct=0000 > usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb1: Product: OHCI Host Controller > usb usb1: Manufacturer: Linux 2.6.17-mm4 ohci_hcd > usb usb1: SerialNumber: 0000:00:13.0 > usb usb1: configuration #1 chosen from 1 choice > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 4 ports detected > hda: cache flushes supported > ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 16 > ohci_hcd 0000:00:13.1: OHCI Host Controller > ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2 > ohci_hcd 0000:00:13.1: irq 16, io mem 0xfbdfe000 > Linux agpgart interface v0.101 (c) Dave Jones > usb usb2: new device found, idVendor=0000, idProduct=0000 > usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb2: Product: OHCI Host Controller > usb usb2: Manufacturer: Linux 2.6.17-mm4 ohci_hcd > usb usb2: SerialNumber: 0000:00:13.1 > usb usb2: configuration #1 chosen from 1 choice > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 4 ports detected > Device `[EUSB]' is not power manageable<6>ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 16 > ehci_hcd 0000:00:13.2: EHCI Host Controller > ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3 > ehci_hcd 0000:00:13.2: irq 16, io mem 0xfbdff000 > ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 > usb usb3: new device found, idVendor=0000, idProduct=0000 > usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 > usb usb3: Product: EHCI Host Controller > usb usb3: Manufacturer: Linux 2.6.17-mm4 ehci_hcd > usb usb3: SerialNumber: 0000:00:13.2 > usb usb3: configuration #1 chosen from 1 choice > hub 3-0:1.0: USB hub found > hub 3-0:1.0: 8 ports detected > ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 17 (level, low) -> IRQ 22 > ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 17 (level, low) -> IRQ 22 > Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled > cs: IO port probe 0x100-0x4ff: excluding 0x408-0x40f 0x4d0-0x4d7 > cs: IO port probe 0x800-0x8ff: clean. > cs: IO port probe 0xc00-0xcff: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcdf 0xcf8-0xcff > cs: IO port probe 0xa00-0xaff: clean. > cs: IO port probe 0x100-0x4ff: excluding 0x408-0x40f 0x4d0-0x4d7 > cs: IO port probe 0x800-0x8ff: clean. > cs: IO port probe 0xc00-0xcff: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcdf 0xcf8-0xcff > cs: IO port probe 0xa00-0xaff: clean. > hda: cache flushes supported > Adding 1349420k swap on /dev/hda5. Priority:-1 extents:1 across:1349420k > Linux video capture interface: v2.00 > saa7130/34: v4l2 driver version 0.2.14 loaded > pcmcia: Detected deprecated PCMCIA ioctl usage from process: discover. > pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools. > pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details. > NET: Registered protocol family 17 > ACPI: Battery Slot [BAT1] (battery present) > ACPI: AC Adapter [ADP1] (on-line) > ACPI: duty_cycle spans bit 4 > ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) > ACPI: Power Button (FF) [PWRF] > ACPI: Lid Switch [LID0] > ACPI: Sleep Button (CM) [SLPB] > ACPI: Power Button (CM) [PWRB] > ACPI: Thermal Zone [THRM] (64 C) > Time: acpi_pm clocksource has been installed. > powernow-k8: Found 1 AMD Turion(tm) 64 Mobile Technology ML-30 processors (version 2.00.00) > ACPI: Invalid package argument > ACPI Exception (acpi_processor-0272): AE_BAD_PARAMETER, Invalid _PSS data [20060623] > powernow-k8: 0 : fid 0x0 (800 MHz), vid 0x12 > powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0x4 > powernow-k8: ph2 null fid transition 0x8 > [drm] Initialized drm 1.0.1 20051102 > psmouse.c: TouchPad at isa0060/serio2/input0 - driver resynched.
-- Nathan - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |