Messages in this thread | | | Date | Thu, 22 Jun 2006 00:48:11 +0200 | From | "J.A. Magallón" <> | Subject | Using libata for ICH5 PATA |
| |
Hi...
I want to try to use libata for my ide disks also. Board is an ASUS PC-DL, it has an ICH5R controller:
00:1f.1 IDE interface: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller (rev 02) 00:1f.2 IDE interface: Intel Corporation 82801EB (ICH5) SATA Controller (rev 02)
with 2 IDE100 busses and 2 sata ports, and a Promise one:
03:04.0 RAID bus controller: Promise Technology, Inc. PDC20378 (FastTrak 378/SATA 378) (rev 02)
with one IDE133 bus and 2 sata ports. More details here: http://www.asus.com/products.aspx?l1=9&l2=39&l3=99&model=104&modelmenu=1
I boot from a SATA drive in ICH5, no initrd/initramfs, so SATA support for ICH5 is compiled in.
I have now 2.6.17-mm1 installed, configured with:
CONFIG_IDE=m CONFIG_BLK_DEV_IDE=m CONFIG_BLK_DEV_IDEPCI=y CONFIG_BLK_DEV_PIIX=m CONFIG_SCSI=y CONFIG_SCSI_SATA=y CONFIG_SCSI_PATA_OLDPIIX=m CONFIG_SCSI_ATA_PIIX=y CONFIG_SCSI_SATA_PROMISE=m
The ata_piix does not show the PATA bus.
libata version 1.30 loaded. ata_piix 0000:00:1f.2: version 1.10tj1ac3 ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ] ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1f.2 to 64 ata1: SATA max UDMA/133 cmd 0xC000 ctl 0xC402 bmdma 0xD000 irq 16 ata2: SATA max UDMA/133 cmd 0xC800 ctl 0xCC02 bmdma 0xD008 irq 16 scsi0 : ata_piix ata1: ENTER, pcs=0x13 base=0 ata1: LEAVE, pcs=0x13 present_mask=0x1 ata1.00: cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:407f ata1.00: ATA-6, max UDMA/133, 390721968 sectors: LBA48 ata1.00: configured for UDMA/133 scsi1 : ata_piix ata2: ENTER, pcs=0x13 base=2 ata2: LEAVE, pcs=0x11 present_mask=0x0 ata2: SATA port has no device. Vendor: ATA Model: ST3200822AS Rev: 3.01 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 sda3
If I modprobe sata_promise, it works as I expected:
Jun 22 00:11:03 werewolf kernel: sata_promise 0000:03:04.0: version 1.04 Jun 22 00:11:03 werewolf kernel: ACPI: PCI Interrupt 0000:03:04.0[A] -> GSI 23 (level, low) -> IRQ 17 Jun 22 00:11:03 werewolf kernel: sata_promise PATA port found Jun 22 00:11:03 werewolf kernel: ata3: SATA max UDMA/133 cmd 0xF8B8A200 ctl 0xF8B8A238 bmdma 0x0 irq 17 Jun 22 00:11:03 werewolf kernel: ata4: SATA max UDMA/133 cmd 0xF8B8A280 ctl 0xF8B8A2B8 bmdma 0x0 irq 17 Jun 22 00:11:03 werewolf kernel: ata5: PATA max UDMA/133 cmd 0xF8B8A300 ctl 0xF8B8A338 bmdma 0x0 irq 17 Jun 22 00:11:03 werewolf kernel: scsi2 : sata_promise Jun 22 00:11:03 werewolf kernel: ata3: SATA link down (SStatus 0 SControl 300) Jun 22 00:11:03 werewolf kernel: scsi3 : sata_promise Jun 22 00:11:04 werewolf kernel: ata4: SATA link down (SStatus 0 SControl 0) Jun 22 00:11:04 werewolf kernel: scsi4 : sata_promise Jun 22 00:11:05 werewolf kernel: ata5: disabling port
Finds both SATAs and the PATA.
This is what the 'old way' with piix gives:
Jun 22 00:12:42 werewolf kernel: ICH5: IDE controller at PCI slot 0000:00:1f.1 Jun 22 00:12:42 werewolf kernel: ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 16 Jun 22 00:12:42 werewolf kernel: ICH5: chipset revision 2 Jun 22 00:12:42 werewolf kernel: ICH5: not 100% native mode: will probe irqs later Jun 22 00:12:42 werewolf kernel: ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio Jun 22 00:12:42 werewolf kernel: ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio Jun 22 00:12:42 werewolf kernel: Probing IDE interface ide0... Jun 22 00:12:42 werewolf kernel: hda: HL-DT-ST DVDRAM GSA-4120B, ATAPI CD/DVD-ROM drive Jun 22 00:12:43 werewolf kernel: hdb: IOMEGA ZIP 250 ATAPI, ATAPI FLOPPY drive Jun 22 00:12:43 werewolf kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Jun 22 00:12:43 werewolf kernel: hda: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33) Jun 22 00:12:43 werewolf kernel: Uniform CD-ROM driver Revision: 3.20 Jun 22 00:12:43 werewolf kernel: Probing IDE interface ide1... Jun 22 00:12:43 werewolf kernel: ide-floppy driver 0.99.newide Jun 22 00:12:43 werewolf kernel: hdb: No disk in drive Jun 22 00:12:43 werewolf kernel: hdb: 244736kB, 239/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm Jun 22 00:12:43 werewolf kernel: hdb: No disk in drive Jun 22 00:12:43 werewolf kernel: hdb: No disk in drive Jun 22 00:12:43 werewolf udevd-event[2800]: find_free_number: %e is deprecated, will be removed and is unlikely to work correctly. Don't use it. Jun 22 00:12:43 werewolf kernel: hdc: ST3120022A, ATA DISK drive Jun 22 00:12:44 werewolf kernel: hdd: TOSHIBA DVD-ROM SD-M1712, ATAPI CD/DVD-ROM drive Jun 22 00:12:44 werewolf kernel: ide1 at 0x170-0x177,0x376 on irq 15 Jun 22 00:12:44 werewolf kernel: hdd: ATAPI 48X DVD-ROM drive, 128kB Cache, UDMA(33) Jun 22 00:12:44 werewolf kernel: hdc: max request size: 512KiB Jun 22 00:12:44 werewolf kernel: hdc: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100) Jun 22 00:12:44 werewolf kernel: hdc: cache flushes supported Jun 22 00:12:44 werewolf kernel: hdc: hdc1
What do I need to let libata drive the ICH5 pata ?
TIA
-- J.A. Magallon <jamagallon()ono!com> \ Software is like sex: \ It's better when it's free Mandriva Linux release 2007.0 (Cooker) for i586 Linux 2.6.17-jam01 (gcc 4.1.1 20060518 (prerelease)) #2 SMP PREEMPT Wed - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |