Messages in this thread Patch in this message | | | From | Bjorn Helgaas <> | Subject | [PATCH 5/7] CCISS: fix a few spelling errors | Date | Wed, 14 Jun 2006 17:11:38 -0600 |
| |
Fix a few spelling errors.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Index: rc5-mm3/drivers/block/cciss.c =================================================================== --- rc5-mm3.orig/drivers/block/cciss.c 2006-06-14 15:16:13.000000000 -0600 +++ rc5-mm3/drivers/block/cciss.c 2006-06-14 15:16:44.000000000 -0600 @@ -129,7 +129,7 @@ { 0x3215103C, "Smart Array E200i", &SA5_access}, }; -/* How long to wait (in millesconds) for board to go into simple mode */ +/* How long to wait (in milliseconds) for board to go into simple mode */ #define MAX_CONFIG_WAIT 30000 #define MAX_IOCTL_CONFIG_WAIT 1000 @@ -1117,7 +1117,7 @@ * * Right now I'm using the getgeometry() function to do this, but this * function should probably be finer grained and allow you to revalidate one - * particualar logical volume (instead of all of them on a particular + * particular logical volume (instead of all of them on a particular * controller). */ static int revalidate_allvol(ctlr_info_t *host) @@ -1260,7 +1260,7 @@ return; - /* Get information about the disk and modify the driver sturcture */ + /* Get information about the disk and modify the driver structure */ size_buff = kmalloc(sizeof( ReadCapdata_struct), GFP_KERNEL); if (size_buff == NULL) goto mem_msg; @@ -1335,7 +1335,7 @@ } /* This function will add and remove logical drives from the Logical - * drive array of the controller and maintain persistancy of ordering + * drive array of the controller and maintain persistency of ordering * so that mount points are preserved until the next reboot. This allows * for the removal of logical drives in the middle of the drive array * without a re-ordering of those drives. @@ -1482,7 +1482,7 @@ * clear_all = This flag determines whether or not the disk information * is going to be completely cleared out and the highest_lun * reset. Sometimes we want to clear out information about - * the disk in preperation for re-adding it. In this case + * the disk in preparation for re-adding it. In this case * the highest_lun should be left unchanged and the LunID * should not be cleared. */ @@ -2597,7 +2597,7 @@ return IRQ_HANDLED; } /* - * We cannot read the structure directly, for portablity we must use + * We cannot read the structure directly, for portability we must use * the io functions. * This is for debug only. */ @@ -2620,9 +2620,9 @@ readl(&(tb->TransportActive))); printk(" Requested transport Method = 0x%x\n", readl(&(tb->HostWrite.TransportRequest))); - printk(" Coalese Interrupt Delay = 0x%x\n", + printk(" Coalesce Interrupt Delay = 0x%x\n", readl(&(tb->HostWrite.CoalIntDelay))); - printk(" Coalese Interrupt Count = 0x%x\n", + printk(" Coalesce Interrupt Count = 0x%x\n", readl(&(tb->HostWrite.CoalIntCount))); printk(" Max outstanding commands = 0x%d\n", readl(&(tb->CmdsOutMax))); - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |