lkml.org 
[lkml]   [2006]   [Mar]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: New libata PATA patch for 2.6.16-rc1
Date
Hi,

I tried your ide1 patch with 2.6.16-rc6 and NFORCE2 board, thus using the AMD
driver (and sil sata driver).

I get this in dmesg:

libata version 1.20 loaded.
sata_sil 0000:01:0b.0: version 0.9
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [APC3] -> GSI 18 (level, high) ->
IRQ 18
ata1: SATA max UDMA/100 cmd 0xF0806080 ctl 0xF080608A bmdma 0xF0806000 irq 18
ata2: SATA max UDMA/100 cmd 0xF08060C0 ctl 0xF08060CA bmdma 0xF0806008 irq 18
ata1: SATA link up 1.5 Gbps (SStatus 113)
ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4773 85:7c69 86:3e01 87:4763
88:207f
ata1: dev 0 ATA-7, max UDMA/133, 586114704 sectors: LBA48
ata1: dev 0 configured for UDMA/100
scsi0 : sata_sil
ata2: SATA link down (SStatus 0)
scsi1 : sata_sil
Vendor: ATA Model: Maxtor 7V300F0 Rev: VA11
Type: Direct-Access ANSI SCSI revision: 05
pata_amd 0000:00:09.0: version 0.1.3
PCI: Setting latency timer of device 0000:00:09.0 to 64
ata3: PATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xF000 irq 14
ata3: dev 0 cfg 49:0b00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000
88:0407
ata3: dev 0 ATAPI, max UDMA/33
ata3: PIO error
ata3: dev 0 configured for UDMA/33
scsi2 : pata_amd
Vendor: NU Model: DVDRW DDW-081 Rev: BX32
Type: CD-ROM ANSI SCSI revision: 05
ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xF008 irq 15
ATA: abnormal status 0x7F on port 0x177
ata4: dev 0 cfg 49:0e00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000
88:0000
ata4: no dma
ata4: dev 0 not supported, ignoring
scsi3 : pata_amd
SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 < sda5 sda6 sda7 sda8 sda9 > sda3
sd 0:0:0:0: Attached scsi disk sda
sr0: scsi3-mmc drive: 12x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 2:0:0:0: Attached scsi CD-ROM sr0
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 2:0:0:0: Attached scsi generic sg1 type 5


Though log gives a PIO error (see above) for the DVD+RW drive, it seems to
work w/o problems in a quick test. But I have a ATAPI ZIP-100 drive connected
to the secondary master port and this device doesn't show up. The log seems
to indicate some problems. I know it is a PIO0 device, so maybe this is the
problem? PIO not implemented, yet? Or have I missed a SCSI option to be
enabled?

I will see how the DVD+RW drive behaves and let you know whether it makes
troubles. :-)

Cheers,
--
(°= =°)
//\ Prakash Punnoor /\\
V_/ \_V
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2006-03-13 23:34    [W:0.126 / U:0.204 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site