lkml.org 
[lkml]   [2006]   [Feb]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    From
    Subject2.6.16-rc4 libata + AHCI patched for suspend fails on ICH6
    Date
    Hi Jens,

    regarding your suspend support patch for libata:

    > author Jens Axboe <axboe@suse.de>
    > Fri, 6 Jan 2006 08:28:07 +0000 (09:28 +0100)
    > commit 9b847548663ef1039dd49f0eb4463d001e596bc3

    > [PATCH] Suspend support for libata
    > This patch adds suspend patch to libata, and ata_piix in particular.
    > For most low level drivers, they should just need to add the 4 hooks to
    > work. As I can only test ata_piix, I didn't enable it for more though.

    i tested the trivial "4-hooks" patch on kernel 2.6.16-rc4, on my laptop
    (i915, ICH6 chipset, sata hd - a Fujitsu-Siemens 7020)
    but it doesn't work as it should:
    after resume the drive fails to respond to the commands so it
    ends up remounted read-only.

    I am attaching:
    - the trivial patch i used
    - the output of lsmod (lsmod-clean.txt)
    - the output of lspci -vv before (lspci-clean.txt)
    and after resuming (lspci-resume.txt)
    - the output of dmesg (glueing the full boot + resuming messages)

    All this was done running in single mode. I also tried suspending after
    removing all unnecessary modules (usb, snd,ide,...), same result.

    BTW, running a 'diff lspci-clean.txt lspci-resume.txt'
    i also noticed that after resume some pci devices get a different
    "BusMaster" polarity, but the SATA controller doesn't.

    I would be glad to test patches/debug other things, feel free to ask.

    (Please CC me if replying to the ml, i'm not subscribed)

    Thanks a lot!!

    Ariel Garcia
    216a217,218
    > .resume = ata_scsi_device_resume,
    > .suspend = ata_scsi_device_suspend,
    301a304,305
    > .resume = ata_pci_device_resume,
    > .suspend = ata_pci_device_suspend,
    0000:00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 04)
    Subsystem: Fujitsu Limited.: Unknown device 12d7
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
    Latency: 0
    Capabilities: [e0] #09 [2109]

    0000:00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 04) (prog-if 00 [VGA])
    Subsystem: Fujitsu Limited.: Unknown device 12de
    Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Interrupt: pin A routed to IRQ 11
    Region 0: Memory at b0080000 (32-bit, non-prefetchable) [size=512K]
    Region 1: I/O ports at 1400 [size=8]
    Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M]
    Region 3: Memory at b0040000 (32-bit, non-prefetchable) [size=256K]
    Capabilities: [d0] Power Management version 2
    Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-

    0000:00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 04)
    Subsystem: Fujitsu Limited.: Unknown device 12de
    Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Region 0: Memory at 52000000 (32-bit, non-prefetchable) [disabled] [size=512K]
    Capabilities: [d0] Power Management version 2
    Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-

    0000:00:1b.0 0403: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 04)
    Subsystem: Fujitsu Limited.: Unknown device 1326
    Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Interrupt: pin A routed to IRQ 177
    Region 0: Memory at b0000000 (64-bit, non-prefetchable) [size=16K]
    Capabilities: [50] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
    Address: 0000000000000000 Data: 0000
    Capabilities: [70] #10 [0091]

    0000:00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 04) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0, Cache Line Size: 0x08 (32 bytes)
    Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
    Memory behind bridge: b0100000-b01fffff
    BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
    Capabilities: [40] #10 [0141]
    Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
    Address: fee00000 Data: 40c1
    Capabilities: [90] #0d [0000]
    Capabilities: [a0] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-

    0000:00:1c.1 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 2 (rev 04) (prog-if 00 [Normal decode])
    Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0, Cache Line Size: 0x08 (32 bytes)
    Bus: primary=00, secondary=03, subordinate=04, sec-latency=0
    BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
    Capabilities: [40] #10 [0141]
    Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
    Address: fee00000 Data: 40c9
    Capabilities: [90] #0d [0000]
    Capabilities: [a0] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-

    0000:00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 04) (prog-if 00 [UHCI])
    Subsystem: Fujitsu Limited.: Unknown device 12e8
    Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Interrupt: pin A routed to IRQ 209
    Region 4: I/O ports at 1420 [size=32]

    0000:00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 04) (prog-if 00 [UHCI])
    Subsystem: Fujitsu Limited.: Unknown device 12e8
    Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Interrupt: pin B routed to IRQ 217
    Region 4: I/O ports at 1440 [size=32]

    0000:00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 04) (prog-if 00 [UHCI])
    Subsystem: Fujitsu Limited.: Unknown device 12e8
    Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Interrupt: pin C routed to IRQ 225
    Region 4: I/O ports at 1460 [size=32]

    0000:00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 04) (prog-if 00 [UHCI])
    Subsystem: Fujitsu Limited.: Unknown device 12e8
    Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Interrupt: pin D routed to IRQ 177
    Region 4: I/O ports at 1480 [size=32]

    0000:00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 04) (prog-if 20 [EHCI])
    Subsystem: Fujitsu Limited.: Unknown device 12e9
    Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Interrupt: pin A routed to IRQ 209
    Region 0: Memory at b0004000 (32-bit, non-prefetchable) [size=1K]
    Capabilities: [50] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [58] #0a [20a0]

    0000:00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d4) (prog-if 01 [Subtractive decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Bus: primary=00, secondary=06, subordinate=07, sec-latency=32
    I/O behind bridge: 00002000-00002fff
    Memory behind bridge: b0200000-b02fffff
    Prefetchable memory behind bridge: 0000000050000000-0000000051f00000
    BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
    Capabilities: [50] #0d [0000]

    0000:00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 04)
    Subsystem: Fujitsu Limited.: Unknown device 12e4
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0

    0000:00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 04) (prog-if 8a [Master SecP PriP])
    Subsystem: Fujitsu Limited.: Unknown device 12e5
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin A routed to IRQ 225
    Region 0: I/O ports at <unassigned>
    Region 1: I/O ports at <unassigned>
    Region 2: I/O ports at <unassigned>
    Region 3: I/O ports at <unassigned>
    Region 4: I/O ports at 1410 [size=16]

    0000:00:1f.2 0106: Intel Corporation 82801FBM (ICH6M) SATA Controller (rev 04) (prog-if 01)
    Subsystem: Fujitsu Limited.: Unknown device 12e6
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin B routed to IRQ 217
    Region 0: I/O ports at 14b8 [size=8]
    Region 1: I/O ports at 140c [size=4]
    Region 2: I/O ports at 14b0 [size=8]
    Region 3: I/O ports at 1408 [size=4]
    Region 4: I/O ports at 14a0 [size=16]
    Region 5: Memory at b0004400 (32-bit, non-prefetchable) [size=1K]
    Capabilities: [70] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-

    0000:00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 04)
    Subsystem: Fujitsu Limited.: Unknown device 12e7
    Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Interrupt: pin B routed to IRQ 11
    Region 4: I/O ports at 14c0 [size=32]

    0000:02:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5751M Gigabit Ethernet PCI Express (rev 21)
    Subsystem: Fujitsu Limited.: Unknown device 1300
    Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Interrupt: pin A routed to IRQ 177
    Region 0: Memory at b0100000 (64-bit, non-prefetchable) [size=64K]
    Capabilities: [48] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=1 PME-
    Capabilities: [50] Vital Product Data
    Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
    Address: 06061068cc09b100 Data: 1c20
    Capabilities: [d0] #10 [0001]

    0000:06:03.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 20)
    Subsystem: Fujitsu Limited.: Unknown device 131e
    Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Interrupt: pin A routed to IRQ 177
    Region 0: Memory at b0206000 (32-bit, non-prefetchable) [size=4K]
    Bus: primary=06, secondary=07, subordinate=0a, sec-latency=176
    Memory window 0: 50000000-51fff000 (prefetchable)
    Memory window 1: 54000000-55fff000
    I/O window 0: 00002000-000020ff
    I/O window 1: 00002400-000024ff
    BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
    16-bit legacy interface ports at 0001

    0000:06:05.0 Network controller: Intel Corporation PRO/Wireless 2200BG (rev 05)
    Subsystem: Intel Corporation: Unknown device 2702
    Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Interrupt: pin A routed to IRQ 225
    Region 0: Memory at b0204000 (32-bit, non-prefetchable) [size=4K]
    Capabilities: [dc] Power Management version 2
    Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=1 PME-

    0000:06:06.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
    Subsystem: Fujitsu Limited.: Unknown device 1162
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32 (500ns min, 1000ns max), Cache Line Size: 0x08 (32 bytes)
    Interrupt: pin A routed to IRQ 11
    Region 0: Memory at b0205000 (32-bit, non-prefetchable) [size=2K]
    Region 1: Memory at b0200000 (32-bit, non-prefetchable) [size=16K]
    Capabilities: [44] Power Management version 2
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=55mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-

    0000:00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 04)
    Subsystem: Fujitsu Limited.: Unknown device 12d7
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Capabilities: [e0] #09 [2109]

    0000:00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 04) (prog-if 00 [VGA])
    Subsystem: Fujitsu Limited.: Unknown device 12de
    Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Interrupt: pin A routed to IRQ 11
    Region 0: Memory at b0080000 (32-bit, non-prefetchable) [size=512K]
    Region 1: I/O ports at 1400 [size=8]
    Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M]
    Region 3: Memory at b0040000 (32-bit, non-prefetchable) [size=256K]
    Capabilities: [d0] Power Management version 2
    Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-

    0000:00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 04)
    Subsystem: Fujitsu Limited.: Unknown device 12de
    Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Region 0: Memory at 52000000 (32-bit, non-prefetchable) [disabled] [size=512K]
    Capabilities: [d0] Power Management version 2
    Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-

    0000:00:1b.0 0403: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 04)
    Subsystem: Fujitsu Limited.: Unknown device 1326
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0, Cache Line Size: 0x08 (32 bytes)
    Interrupt: pin A routed to IRQ 177
    Region 0: Memory at b0000000 (64-bit, non-prefetchable) [size=16K]
    Capabilities: [50] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
    Address: 0000000000000000 Data: 0000
    Capabilities: [70] #10 [0091]

    0000:00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 04) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0, Cache Line Size: 0x08 (32 bytes)
    Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
    Memory behind bridge: b0100000-b01fffff
    BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
    Capabilities: [40] #10 [0141]
    Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
    Address: fee00000 Data: 40c1
    Capabilities: [90] #0d [0000]
    Capabilities: [a0] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-

    0000:00:1c.1 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 2 (rev 04) (prog-if 00 [Normal decode])
    Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0, Cache Line Size: 0x08 (32 bytes)
    Bus: primary=00, secondary=03, subordinate=04, sec-latency=0
    BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
    Capabilities: [40] #10 [0141]
    Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
    Address: fee00000 Data: 40c9
    Capabilities: [90] #0d [0000]
    Capabilities: [a0] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-

    0000:00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 04) (prog-if 00 [UHCI])
    Subsystem: Fujitsu Limited.: Unknown device 12e8
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin A routed to IRQ 209
    Region 4: I/O ports at 1420 [size=32]

    0000:00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 04) (prog-if 00 [UHCI])
    Subsystem: Fujitsu Limited.: Unknown device 12e8
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin B routed to IRQ 217
    Region 4: I/O ports at 1440 [size=32]

    0000:00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 04) (prog-if 00 [UHCI])
    Subsystem: Fujitsu Limited.: Unknown device 12e8
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin C routed to IRQ 225
    Region 4: I/O ports at 1460 [size=32]

    0000:00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 04) (prog-if 00 [UHCI])
    Subsystem: Fujitsu Limited.: Unknown device 12e8
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin D routed to IRQ 177
    Region 4: I/O ports at 1480 [size=32]

    0000:00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 04) (prog-if 20 [EHCI])
    Subsystem: Fujitsu Limited.: Unknown device 12e9
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin A routed to IRQ 209
    Region 0: Memory at b0004000 (32-bit, non-prefetchable) [size=1K]
    Capabilities: [50] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [58] #0a [20a0]

    0000:00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d4) (prog-if 01 [Subtractive decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Bus: primary=00, secondary=06, subordinate=07, sec-latency=32
    I/O behind bridge: 00002000-00002fff
    Memory behind bridge: b0200000-b02fffff
    Prefetchable memory behind bridge: 0000000050000000-0000000051f00000
    BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
    Capabilities: [50] #0d [0000]

    0000:00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 04)
    Subsystem: Fujitsu Limited.: Unknown device 12e4
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0

    0000:00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 04) (prog-if 8a [Master SecP PriP])
    Subsystem: Fujitsu Limited.: Unknown device 12e5
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin A routed to IRQ 225
    Region 0: I/O ports at <unassigned>
    Region 1: I/O ports at <unassigned>
    Region 2: I/O ports at <unassigned>
    Region 3: I/O ports at <unassigned>
    Region 4: I/O ports at 1410 [size=16]

    0000:00:1f.2 0106: Intel Corporation 82801FBM (ICH6M) SATA Controller (rev 04) (prog-if 01)
    Subsystem: Fujitsu Limited.: Unknown device 12e6
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin B routed to IRQ 217
    Region 0: I/O ports at 14b8 [size=8]
    Region 1: I/O ports at 140c [size=4]
    Region 2: I/O ports at 14b0 [size=8]
    Region 3: I/O ports at 1408 [size=4]
    Region 4: I/O ports at 14a0 [size=16]
    Region 5: Memory at b0004400 (32-bit, non-prefetchable) [size=1K]
    Capabilities: [70] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-

    0000:00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 04)
    Subsystem: Fujitsu Limited.: Unknown device 12e7
    Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Interrupt: pin B routed to IRQ 11
    Region 4: I/O ports at 14c0 [size=32]

    0000:02:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5751M Gigabit Ethernet PCI Express (rev 21)
    Subsystem: Fujitsu Limited.: Unknown device 1300
    Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Interrupt: pin A routed to IRQ 177
    Region 0: Memory at b0100000 (64-bit, non-prefetchable) [disabled] [size=64K]
    Capabilities: [48] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=1 PME-
    Capabilities: [50] Vital Product Data
    Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
    Address: 06061068cc09b100 Data: 1c20
    Capabilities: [d0] #10 [0001]

    0000:06:03.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 20)
    Subsystem: Fujitsu Limited.: Unknown device 131e
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 168
    Interrupt: pin A routed to IRQ 177
    Region 0: Memory at b0206000 (32-bit, non-prefetchable) [size=4K]
    Bus: primary=06, secondary=07, subordinate=0a, sec-latency=176
    Memory window 0: 50000000-51fff000 (prefetchable)
    Memory window 1: 54000000-55fff000
    I/O window 0: 00002000-000020ff
    I/O window 1: 00002400-000024ff
    BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
    16-bit legacy interface ports at 0001

    0000:06:05.0 Network controller: Intel Corporation PRO/Wireless 2200BG (rev 05)
    Subsystem: Intel Corporation: Unknown device 2702
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32 (750ns min, 6000ns max), Cache Line Size: 0x08 (32 bytes)
    Interrupt: pin A routed to IRQ 225
    Region 0: Memory at b0204000 (32-bit, non-prefetchable) [size=4K]
    Capabilities: [dc] Power Management version 2
    Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=1 PME-

    0000:06:06.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
    Subsystem: Fujitsu Limited.: Unknown device 1162
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32 (500ns min, 1000ns max), Cache Line Size: 0x08 (32 bytes)
    Interrupt: pin A routed to IRQ 11
    Region 0: Memory at b0205000 (32-bit, non-prefetchable) [size=2K]
    Region 1: Memory at b0200000 (32-bit, non-prefetchable) [size=16K]
    Capabilities: [44] Power Management version 2
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=55mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-

    Module Size Used by
    agpgart 32284 1 intel_agp
    ahci 14340 5
    cdrom 37552 1 ide_cd
    cpufreq_conservative 6756 0
    cpufreq_ondemand 5980 0
    ehci_hcd 33160 0
    evdev 9536 0
    ext3 125256 4
    fan 4484 0
    fat 52508 1 vfat
    firmware_class 10816 2 pcmcia,ipw2200
    freq_table 4612 1 speedstep_centrino
    generic 4292 0 [permanent]
    i2c_core 22160 1 i2c_i801
    i2c_i801 8332 0
    ide_cd 40096 0
    ide_core 126064 6 usb_storage,ide_disk,ide_generic,ide_cd,piix,generic
    ide_disk 16640 0
    ide_generic 1216 0 [permanent]
    ieee80211 32584 1 ipw2200
    ieee80211_crypt 6528 1 ieee80211
    intel_agp 22684 1
    ipw2200 111340 0
    jbd 60244 1 ext3
    libata 60428 1 ahci
    mbcache 9220 1 ext3
    mousedev 11712 0
    nls_cp437 5696 0
    nls_iso8859_1 4096 0
    pcmcia 30344 0
    pcmcia_core 41936 3 pcmcia,yenta_socket,rsrc_nonstatic
    pcspkr 3460 0
    piix 10308 0 [permanent]
    processor 21888 2 speedstep_centrino,thermal
    psmouse 38532 0
    rsrc_nonstatic 11904 1 yenta_socket
    rtc 13748 0
    scsi_mod 136268 4 usb_storage,sd_mod,ahci,libata
    sd_mod 17040 6
    serio_raw 7236 0
    snd 54176 6 snd_hda_intel,snd_hda_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
    snd_hda_codec 121792 1 snd_hda_intel
    snd_hda_intel 17552 0
    snd_mixer_oss 18240 1 snd_pcm_oss
    snd_page_alloc 10504 2 snd_hda_intel,snd_pcm
    snd_pcm 88264 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss
    snd_pcm_oss 51328 0
    snd_timer 24580 1 snd_pcm
    soundcore 10336 1 snd
    speedstep_centrino 7352 1
    tg3 101636 0
    thermal 12872 0
    uhci_hcd 32656 0
    usb_storage 71104 0
    usbcore 129888 4 usb_storage,ehci_hcd,uhci_hcd
    vfat 13312 0
    yenta_socket 14604 1
    ACPI init
    [4294671.424000] pnp: PnP ACPI: found 9 devices
    [4294671.424000] PCI: Using ACPI for IRQ routing
    [4294671.424000] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
    [4294671.425000] PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.1
    [4294671.425000] PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.1
    [4294671.425000] PCI: Cannot allocate resource region 9 of bridge 0000:00:1c.1
    [4294671.443000] PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
    [4294671.443000] PCI: Bridge: 0000:00:1c.0
    [4294671.443000] IO window: disabled.
    [4294671.443000] MEM window: b0100000-b01fffff
    [4294671.443000] PREFETCH window: disabled.
    [4294671.443000] PCI: Bridge: 0000:00:1c.1
    [4294671.444000] IO window: disabled.
    [4294671.444000] MEM window: disabled.
    [4294671.444000] PREFETCH window: disabled.
    [4294671.444000] PCI: Bus 7, cardbus bridge: 0000:06:03.0
    [4294671.444000] IO window: 00002000-000020ff
    [4294671.444000] IO window: 00002400-000024ff
    [4294671.444000] PREFETCH window: 50000000-51ffffff
    [4294671.444000] MEM window: 54000000-55ffffff
    [4294671.444000] PCI: Bridge: 0000:00:1e.0
    [4294671.444000] IO window: 2000-2fff
    [4294671.444000] MEM window: b0200000-b02fffff
    [4294671.444000] PREFETCH window: 50000000-51ffffff
    [4294671.444000] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 169
    [4294671.444000] PCI: Setting latency timer of device 0000:00:1c.0 to 64
    [4294671.444000] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 177
    [4294671.445000] PCI: Setting latency timer of device 0000:00:1c.1 to 64
    [4294671.445000] PCI: Setting latency timer of device 0000:00:1e.0 to 64
    [4294671.445000] ACPI: PCI Interrupt 0000:06:03.0[A] -> GSI 16 (level, low) -> IRQ 177
    [4294671.445000] Simple Boot Flag at 0x7f set to 0x1
    [4294671.445000] audit: initializing netlink socket (disabled)
    [4294671.445000] audit(1140368786.443:1): initialized
    [4294671.445000] Initializing Cryptographic API
    [4294671.446000] io scheduler noop registered
    [4294671.446000] io scheduler anticipatory registered (default)
    [4294671.446000] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 169
    [4294671.446000] PCI: Setting latency timer of device 0000:00:1c.0 to 64
    [4294671.446000] assign_interrupt_mode Found MSI capability
    [4294671.446000] Allocate Port Service[0000:00:1c.0:pcie00]
    [4294671.446000] Allocate Port Service[0000:00:1c.0:pcie02]
    [4294671.446000] Allocate Port Service[0000:00:1c.0:pcie03]
    [4294671.446000] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 177
    [4294671.446000] PCI: Setting latency timer of device 0000:00:1c.1 to 64
    [4294671.446000] assign_interrupt_mode Found MSI capability
    [4294671.447000] Allocate Port Service[0000:00:1c.1:pcie00]
    [4294671.447000] Allocate Port Service[0000:00:1c.1:pcie02]
    [4294671.447000] Allocate Port Service[0000:00:1c.1:pcie03]
    [4294671.449000] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
    [4294671.451000] i8042.c: Detected active multiplexing controller, rev 1.1.
    [4294671.453000] serio: i8042 AUX0 port at 0x60,0x64 irq 12
    [4294671.453000] serio: i8042 AUX1 port at 0x60,0x64 irq 12
    [4294671.453000] serio: i8042 AUX2 port at 0x60,0x64 irq 12
    [4294671.453000] serio: i8042 AUX3 port at 0x60,0x64 irq 12
    [4294671.453000] serio: i8042 KBD port at 0x60,0x64 irq 1
    [4294671.454000] RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
    [4294671.454000] STRIP: Version 1.3A-STUART.CHESHIRE (unlimited channels)
    [4294671.455000] MC: drivers/edac/edac_mc.c version edac_mc Ver: 2.0.0 Feb 19 2006
    [4294671.455000] NET: Registered protocol family 2
    [4294671.465000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
    [4294671.465000] TCP established hash table entries: 131072 (order: 7, 524288 bytes)
    [4294671.465000] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
    [4294671.466000] TCP: Hash tables configured (established 131072 bind 65536)
    [4294671.466000] TCP reno registered
    [4294671.466000] TCP bic registered
    [4294671.466000] NET: Registered protocol family 1
    [4294671.466000] NET: Registered protocol family 17
    [4294671.466000] NET: Registered protocol family 8
    [4294671.466000] NET: Registered protocol family 20
    [4294671.466000] Using IPI Shortcut mode
    [4294671.466000] ACPI wakeup devices:
    [4294671.466000] PCIB MODM AZAL EXP1 EXP2 LID
    [4294671.467000] ACPI: (supports S0 S3 S4 S5)
    [4294671.467000] Freeing unused kernel memory: 164k freed
    [4294671.527000] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
    [4294671.615000] input: AT Translated Set 2 keyboard as /class/input/input0
    [4294671.695000] usbcore: registered new driver usbfs
    [4294671.695000] usbcore: registered new driver hub
    [4294671.696000] USB Universal Host Controller Interface driver v2.3
    [4294671.696000] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 209
    [4294671.696000] PCI: Setting latency timer of device 0000:00:1d.0 to 64
    [4294671.696000] uhci_hcd 0000:00:1d.0: UHCI Host Controller
    [4294671.696000] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
    [4294671.696000] uhci_hcd 0000:00:1d.0: irq 209, io base 0x00001420
    [4294671.697000] usb usb1: configuration #1 chosen from 1 choice
    [4294671.697000] hub 1-0:1.0: USB hub found
    [4294671.697000] hub 1-0:1.0: 2 ports detected
    [4294671.798000] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 217
    [4294671.798000] PCI: Setting latency timer of device 0000:00:1d.1 to 64
    [4294671.798000] uhci_hcd 0000:00:1d.1: UHCI Host Controller
    [4294671.798000] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
    [4294671.798000] uhci_hcd 0000:00:1d.1: irq 217, io base 0x00001440
    [4294671.798000] usb usb2: configuration #1 chosen from 1 choice
    [4294671.798000] hub 2-0:1.0: USB hub found
    [4294671.798000] hub 2-0:1.0: 2 ports detected
    [4294671.899000] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 225
    [4294671.899000] PCI: Setting latency timer of device 0000:00:1d.2 to 64
    [4294671.899000] uhci_hcd 0000:00:1d.2: UHCI Host Controller
    [4294671.899000] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
    [4294671.899000] uhci_hcd 0000:00:1d.2: irq 225, io base 0x00001460
    [4294671.900000] usb usb3: configuration #1 chosen from 1 choice
    [4294671.900000] hub 3-0:1.0: USB hub found
    [4294671.900000] hub 3-0:1.0: 2 ports detected
    [4294672.001000] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 177
    [4294672.001000] PCI: Setting latency timer of device 0000:00:1d.3 to 64
    [4294672.001000] uhci_hcd 0000:00:1d.3: UHCI Host Controller
    [4294672.001000] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
    [4294672.001000] uhci_hcd 0000:00:1d.3: irq 177, io base 0x00001480
    [4294672.001000] usb usb4: configuration #1 chosen from 1 choice
    [4294672.001000] hub 4-0:1.0: USB hub found
    [4294672.001000] hub 4-0:1.0: 2 ports detected
    [4294672.102000] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 209
    [4294672.102000] PCI: Setting latency timer of device 0000:00:1d.7 to 64
    [4294672.102000] ehci_hcd 0000:00:1d.7: EHCI Host Controller
    [4294672.102000] ehci_hcd 0000:00:1d.7: debug port 1
    [4294672.102000] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
    [4294672.102000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
    [4294672.103000] ehci_hcd 0000:00:1d.7: irq 209, io mem 0xb0004000
    [4294672.107000] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
    [4294672.107000] usb usb5: configuration #1 chosen from 1 choice
    [4294672.107000] hub 5-0:1.0: USB hub found
    [4294672.107000] hub 5-0:1.0: 8 ports detected
    [4294672.188000] SCSI subsystem initialized
    [4294672.190000] libata version 1.20 loaded.
    [4294672.201000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    [4294672.201000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    [4294672.208000] tg3.c:v3.49 (Feb 2, 2006)
    [4294672.208000] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 177
    [4294672.208000] PCI: Setting latency timer of device 0000:02:00.0 to 64
    [4294672.231000] eth0: Tigon3 [partno(BCM95751m) rev 4201 PHY(5750)] (PCI Express) 10/100/1000BaseT Ethernet 00:0b:5d:c7:47:ef
    [4294672.232000] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
    [4294672.232000] eth0: dma_rwctrl[76180000]
    [4294672.252000] ahci 0000:00:1f.2: version 1.2
    [4294672.252000] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 217
    [4294676.564000] PCI: Setting latency timer of device 0000:00:1f.2 to 64
    [4294676.564000] ahci 0000:00:1f.2: AHCI 0001.0000 32 slots 4 ports 1.5 Gbps 0x5 impl SATA mode
    [4294676.564000] ahci 0000:00:1f.2: flags: 64bit ncq pm led slum part
    [4294676.564000] ata1: SATA max UDMA/133 cmd 0xF882E500 ctl 0x0 bmdma 0x0 irq 217
    [4294676.564000] ata2: SATA max UDMA/133 cmd 0xF882E580 ctl 0x0 bmdma 0x0 irq 217
    [4294676.564000] ata3: SATA max UDMA/133 cmd 0xF882E600 ctl 0x0 bmdma 0x0 irq 217
    [4294676.564000] ata4: SATA max UDMA/133 cmd 0xF882E680 ctl 0x0 bmdma 0x0 irq 217
    [4294676.766000] ata1: SATA link up 1.5 Gbps (SStatus 113)
    [4294676.766000] ata1: dev 0 cfg 49:2f00 82:346b 83:7f09 84:6063 85:346b 86:bf09 87:6063 88:203f
    [4294676.766000] ata1: dev 0 ATA-7, max UDMA/100, 156301488 sectors: LBA48
    [4294676.768000] ata1: dev 0 configured for UDMA/100
    [4294676.768000] scsi0 : ahci
    [4294676.970000] ata2: SATA link down (SStatus 0)
    [4294676.970000] scsi1 : ahci
    [4294677.172000] ata3: SATA link down (SStatus 0)
    [4294677.172000] scsi2 : ahci
    [4294677.374000] ata4: SATA link down (SStatus 0)
    [4294677.374000] scsi3 : ahci
    [4294677.374000] Vendor: ATA Model: FUJITSU MHV2080B Rev: 0000
    [4294677.375000] Type: Direct-Access ANSI SCSI revision: 05
    [4294677.378000] ICH6: IDE controller at PCI slot 0000:00:1f.1
    [4294677.378000] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 225
    [4294677.378000] ICH6: chipset revision 4
    [4294677.378000] ICH6: not 100% native mode: will probe irqs later
    [4294677.378000] ide0: BM-DMA at 0x1410-0x1417, BIOS settings: hda:DMA, hdb:pio
    [4294677.379000] Probing IDE interface ide0...
    [4294677.413000] SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
    [4294677.413000] sda: Write Protect is off
    [4294677.413000] sda: Mode Sense: 00 3a 00 10
    [4294677.413000] SCSI device sda: drive cache: write back w/ FUA
    [4294677.414000] SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
    [4294677.414000] sda: Write Protect is off
    [4294677.414000] sda: Mode Sense: 00 3a 00 10
    [4294677.414000] SCSI device sda: drive cache: write back w/ FUA
    [4294677.414000] sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
    [4294677.531000] sd 0:0:0:0: Attached scsi disk sda
    [4294678.051000] hda: MATSHITAUJ-841Db, ATAPI CD/DVD-ROM drive
    [4294678.357000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    [4294678.367000] hda: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
    [4294678.368000] Uniform CD-ROM driver Revision: 3.20
    [4294678.770000] Probing IDE interface ide1...
    [4294679.371000] Attempting manual resume
    [4294679.371000] swsusp: Resume From Partition 8:6
    [4294679.371000] PM: Checking swsusp image.
    [4294679.371000] PM: Resume from disk failed.
    [4294679.384000] EXT3-fs: INFO: recovery required on readonly filesystem.
    [4294679.384000] EXT3-fs: write access will be enabled during recovery.
    [4294680.065000] EXT3-fs: recovery complete.
    [4294680.065000] kjournald starting. Commit interval 5 seconds
    [4294680.071000] EXT3-fs: mounted filesystem with ordered data mode.
    [4294682.065000] Real Time Clock Driver v1.12ac
    [4294682.069000] Linux agpgart interface v0.101 (c) Dave Jones
    [4294682.070000] agpgart: Detected an Intel 915GM Chipset.
    [4294682.070000] agpgart: Detected 7932K stolen memory.
    [4294682.090000] agpgart: AGP aperture is 256M @ 0xc0000000
    [4294682.108000] input: PC Speaker as /class/input/input1
    [4294682.211000] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 177
    [4294682.212000] PCI: Setting latency timer of device 0000:00:1b.0 to 64
    [4294682.560000] hw_random: RNG not detected
    [4294682.816000] Synaptics Touchpad, model: 1, fw: 5.9, id: 0xf8eb1, caps: 0xa04793/0x102000
    [4294682.816000] serio: Synaptics pass-through port at isa0060/serio4/input0
    [4294682.856000] ACPI: PCI Interrupt 0000:06:03.0[A] -> GSI 16 (level, low) -> IRQ 177
    [4294682.857000] Yenta: CardBus bridge found at 0000:06:03.0 [10cf:131e]
    [4294682.858000] input: SynPS/2 Synaptics TouchPad as /class/input/input2
    [4294682.904000] ieee80211_crypt: registered algorithm 'NULL'
    [4294682.906000] ieee80211: 802.11 data/management/control stack, git-1.1.7
    [4294682.906000] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
    [4294682.924000] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, git-1.0.8
    [4294682.924000] ipw2200: Copyright(c) 2003-2005 Intel Corporation
    [4294682.980000] Yenta: ISA IRQ mask 0x0cb8, PCI irq 177
    [4294682.980000] Socket status: 30000006
    [4294682.980000] pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff
    [4294682.980000] pcmcia: parent PCI bridge Memory window: 0xb0200000 - 0xb02fffff
    [4294682.980000] pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x51ffffff
    [4294682.981000] ACPI: PCI Interrupt 0000:06:05.0[A] -> GSI 18 (level, low) -> IRQ 225
    [4294682.981000] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
    [4294683.441000] ipw2200: Radio Frequency Kill Switch is On:
    [4294683.441000] Kill switch must be turned off for wireless networking to work.
    [4294687.034000] input: PS/2 Generic Mouse as /class/input/input3
    [4294687.347000] Adding 1012052k swap on /dev/sda6. Priority:-1 extents:1 across:1012052k
    [4294687.451000] EXT3 FS on sda2, internal journal
    [4294690.531000] mice: PS/2 mouse device common for all mice
    [4294691.902000] kjournald starting. Commit interval 5 seconds
    [4294691.902000] EXT3 FS on sda1, internal journal
    [4294691.902000] EXT3-fs: mounted filesystem with ordered data mode.
    [4294691.922000] kjournald starting. Commit interval 5 seconds
    [4294691.922000] EXT3 FS on sda5, internal journal
    [4294691.922000] EXT3-fs: mounted filesystem with ordered data mode.
    [4294691.924000] kjournald starting. Commit interval 5 seconds
    [4294691.925000] EXT3 FS on sda3, internal journal
    [4294691.925000] EXT3-fs: mounted filesystem with ordered data mode.
    [4294856.664000] usb 5-3: new high speed USB device using ehci_hcd and address 2
    [4294856.790000] usb 5-3: configuration #1 chosen from 1 choice
    [4294856.891000] Initializing USB Mass Storage driver...
    [4294856.892000] scsi4 : SCSI emulation for USB Mass Storage devices
    [4294856.892000] usb-storage: device found at 2
    [4294856.892000] usb-storage: waiting for device to settle before scanning
    [4294856.892000] usbcore: registered new driver usb-storage
    [4294856.892000] USB Mass Storage support registered.
    [4294861.892000] Vendor: Model: USB DISK 2.0 Rev: PMAP
    [4294861.893000] Type: Direct-Access ANSI SCSI revision: 00
    [4294862.070000] SCSI device sdb: 121856 512-byte hdwr sectors (62 MB)
    [4294862.071000] sdb: Write Protect is off
    [4294862.071000] sdb: Mode Sense: 23 00 00 00
    [4294862.071000] sdb: assuming drive cache: write through
    [4294862.073000] SCSI device sdb: 121856 512-byte hdwr sectors (62 MB)
    [4294862.074000] sdb: Write Protect is off
    [4294862.074000] sdb: Mode Sense: 23 00 00 00
    [4294862.074000] sdb: assuming drive cache: write through
    [4294862.074000] sdb: sdb1
    [4294862.075000] sd 4:0:0:0: Attached scsi removable disk sdb
    [4294862.075000] usb-storage: device scan complete


    [4295044.894000] PM: Preparing system for mem sleep
    [4295044.895000] Stopping tasks: ===============|
    [4295045.922000] eth1: Going into suspend...
    [4295045.922000] ACPI: PCI interrupt for device 0000:06:05.0 disabled
    [4295045.933000] ACPI: PCI interrupt for device 0000:06:03.0 disabled
    [4295045.933000] ACPI: PCI interrupt for device 0000:00:1f.2 disabled
    [4295045.944000] ACPI: PCI interrupt for device 0000:00:1d.7 disabled
    [4295045.955000] ACPI: PCI interrupt for device 0000:00:1d.3 disabled
    [4295045.955000] ACPI: PCI interrupt for device 0000:00:1d.2 disabled
    [4295045.955000] ACPI: PCI interrupt for device 0000:00:1d.1 disabled
    [4295045.955000] ACPI: PCI interrupt for device 0000:00:1d.0 disabled
    [4295045.959000] ACPI: PCI interrupt for device 0000:00:1b.0 disabled
    [4295045.959000] PM: Entering mem sleep
    [4295045.959000] Intel machine check architecture supported.
    [4295045.959000] Intel machine check reporting enabled on CPU#0.
    [4295045.959000] Back to C!
    [4295062.959000] PM: Finishing wakeup.
    [4295062.999000] ipw2200: Unable to load ucode: -22
    [4295062.999000] ipw2200: Unable to load firmware: -22
    [4295062.999000] ipw2200: Failed to up device
    [4295063.015000] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 177
    [4295063.015000] PCI: Setting latency timer of device 0000:00:1b.0 to 64
    [4295063.060000] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 169
    [4295063.060000] PCI: Setting latency timer of device 0000:00:1c.0 to 64
    [4295063.060000] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 177
    [4295063.060000] PCI: Setting latency timer of device 0000:00:1c.1 to 64
    [4295063.060000] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 209
    [4295063.060000] PCI: Setting latency timer of device 0000:00:1d.0 to 64
    [4295063.060000] usb usb1: root hub lost power or was reset
    [4295063.060000] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 217
    [4295063.060000] PCI: Setting latency timer of device 0000:00:1d.1 to 64
    [4295063.060000] usb usb2: root hub lost power or was reset
    [4295063.061000] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 225
    [4295063.061000] PCI: Setting latency timer of device 0000:00:1d.2 to 64
    [4295063.061000] usb usb3: root hub lost power or was reset
    [4295063.061000] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 177
    [4295063.061000] PCI: Setting latency timer of device 0000:00:1d.3 to 64
    [4295063.061000] usb usb4: root hub lost power or was reset
    [4295063.072000] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 209
    [4295063.072000] PCI: Setting latency timer of device 0000:00:1d.7 to 64
    [4295063.072000] PCI: Setting latency timer of device 0000:00:1e.0 to 64
    [4295063.072000] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 225
    [4295063.083000] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 217
    [4295063.083000] PCI: Setting latency timer of device 0000:00:1f.2 to 64
    [4295063.083000] ACPI: PCI Interrupt 0000:06:03.0[A] -> GSI 16 (level, low) -> IRQ 177
    [4295063.114000] eth1: Coming out of suspend...
    [4295063.125000] PCI: Enabling device 0000:06:05.0 (0000 -> 0002)
    [4295063.125000] ACPI: PCI Interrupt 0000:06:05.0[A] -> GSI 18 (level, low) -> IRQ 225
    [4295063.125000] pnp: Failed to activate device 00:07.
    [4295063.125000] pnp: Failed to activate device 00:08.
    [4295073.125000] ipw2200: ipw-2.4-boot.fw load failed: Reason -2
    [4295073.125000] ipw2200: Unable to load firmware: -2
    [4295093.907000] ata1: qc timeout (cmd 0xef)
    [4295093.907000] ata1: failed to set xfermode, disabled
    [4295093.907000] ata1: dev 0 configured for UDMA/100
    [4295098.576000] Restarting tasks... done
    [4295098.578000] sd 0:0:0:0: SCSI error: return code = 0x40000
    [4295098.578000] end_request: I/O error, dev sda, sector 169882
    [4295098.578000] sd 0:0:0:0: SCSI error: return code = 0x40000
    [4295098.578000] end_request: I/O error, dev sda, sector 169890
    [4295098.578000] sd 0:0:0:0: SCSI error: return code = 0x40000
    [4295098.578000] end_request: I/O error, dev sda, sector 169898
    [4295098.579000] sd 0:0:0:0: SCSI error: return code = 0x40000
    [4295098.579000] end_request: I/O error, dev sda, sector 169906
    [4295098.579000] Buffer I/O error on device sda2, logical block 1157
    [4295098.579000] lost page write due to I/O error on sda2
    [4295098.579000] Aborting journal on device sda2.
    [4295098.599000] ACPI Error (evevent-0312): No installed handler for fixed event [00000002] [20060127]
    [4295098.601000] ext3_abort called.
    [4295098.601000] EXT3-fs error (device sda2): ext3_journal_start_sb: Detected aborted journal
    [4295098.602000] Remounting filesystem read-only
    [4295098.998000] sd 0:0:0:0: SCSI error: return code = 0x40000
    [4295098.998000] end_request: I/O error, dev sda, sector 14594970
    [4295098.998000] sd 0:0:0:0: SCSI error: return code = 0x40000
    [4295098.998000] end_request: I/O error, dev sda, sector 14594970
    [4295098.998000] sd 0:0:0:0: SCSI error: return code = 0x40000
    [4295098.998000] end_request: I/O error, dev sda, sector 14594970
    [unhandled content-type:application/pgp-signature]
    \
     
     \ /
      Last update: 2006-02-19 20:01    [W:0.091 / U:33.780 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site