lkml.org 
[lkml]   [2006]   [Nov]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    SubjectRe: New laptop - problems with linux
    Francois Romieu wrote:

    >Stephen Clark <Stephen.Clark@seclark.us> :
    >[...]
    >
    >
    >>No it is not loaded - i did a modprobe on it and it loaded but still no
    >>ethx device.
    >>
    >>
    >
    >Send complete 'dmesg' and 'lspci -vvx' (please Cc: netdev@vger.kernel.org)
    >
    >
    >
    lspci and dmesg attached below:
    Thanks, anything else I can do please let me know.

    00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and
    945GT Express Memory Controller Hub (rev 03)
    Subsystem: Intel Corporation Mobile 945GM/PM/GMS/940GML and
    945GT Express Memory Controller Hub
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
    ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort+ >SERR- <PERR-
    Latency: 0
    Capabilities: [e0] Vendor Specific Information
    00: 86 80 a0 27 06 00 90 20 03 00 00 06 00 00 00 00
    10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
    20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 a0 27
    30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00

    00:02.0 VGA compatible controller: Intel Corporation Mobile
    945GM/GMS/940GML Express Integrated Graphics Controller (rev 03)
    (prog-if 00 [VGA])
    Subsystem: ASUSTeK Computer Inc. Unknown device 1252
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
    ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin A routed to IRQ 169
    Region 0: Memory at feb80000 (32-bit, non-prefetchable) [size=512K]
    Region 1: I/O ports at ec00 [size=8]
    Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
    Region 3: Memory at feb40000 (32-bit, non-prefetchable) [size=256K]
    Capabilities: [90] Message Signalled Interrupts: 64bit-
    Queue=0/0 Enable-
    Address: 00000000 Data: 0000
    Capabilities: [d0] Power Management version 2
    Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    00: 86 80 a2 27 07 00 90 00 03 00 00 03 00 00 80 00
    10: 00 00 b8 fe 01 ec 00 00 08 00 00 d0 00 00 b4 fe
    20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 52 12
    30: 00 00 00 00 90 00 00 00 00 00 00 00 05 01 00 00

    00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/940GML
    Express Integrated Graphics Controller (rev 03)
    Subsystem: ASUSTeK Computer Inc. Unknown device 1252
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
    ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Region 0: Memory at fea80000 (32-bit, non-prefetchable) [size=512K]
    Capabilities: [d0] Power Management version 2
    Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    00: 86 80 a6 27 07 00 90 00 03 00 80 03 00 00 80 00
    10: 00 00 a8 fe 00 00 00 00 00 00 00 00 00 00 00 00
    20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 52 12
    30: 00 00 00 00 d0 00 00 00 00 00 00 00 00 00 00 00

    00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High
    Definition Audio Controller (rev 02)
    Subsystem: ASUSTeK Computer Inc. Unknown device 1343
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
    ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0, Cache Line Size: 32 bytes
    Interrupt: pin A routed to IRQ 169
    Region 0: Memory at feb38000 (64-bit, non-prefetchable) [size=16K]
    Capabilities: [50] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
    PME(D0+,D1-,D2-,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [60] Message Signalled Interrupts: 64bit+
    Queue=0/0 Enable-
    Address: 0000000000000000 Data: 0000
    Capabilities: [70] Express Unknown type IRQ 0
    Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
    ExtTag-
    Device: Latency L0s <64ns, L1 <1us
    Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
    Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
    Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
    Link: Supported Speed unknown, Width x0, ASPM unknown,
    Port 0
    Link: Latency L0s <64ns, L1 <1us
    Link: ASPM Disabled CommClk- ExtSynch-
    Link: Speed unknown, Width x0
    00: 86 80 d8 27 06 00 10 00 02 00 03 04 08 00 00 00
    10: 04 80 b3 fe 00 00 00 00 00 00 00 00 00 00 00 00
    20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 43 13
    30: 00 00 00 00 50 00 00 00 00 00 00 00 05 01 00 00

    00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express
    Port 1 (rev 02) (prog-if 00 [Normal decode])
    Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
    ParErr- Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0, Cache Line Size: 32 bytes
    Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort+ <SERR- <PERR-
    BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
    Capabilities: [40] Express Root Port (Slot+) IRQ 0
    Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
    ExtTag-
    Device: Latency L0s unlimited, L1 unlimited
    Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
    Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
    Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
    Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 1
    Link: Latency L0s <1us, L1 <4us
    Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
    Link: Speed 2.5Gb/s, Width x0
    Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+
    Surpise+
    Slot: Number 0, PowerLimit 0.000000
    Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
    Slot: AttnInd Unknown, PwrInd Unknown, Power-
    Root: Correctable- Non-Fatal- Fatal- PME-
    Capabilities: [80] Message Signalled Interrupts: 64bit-
    Queue=0/0 Enable+
    Address: fee00000 Data: 40c9
    Capabilities: [90] #0d [0000]
    Capabilities: [a0] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    PME(D0+,D1-,D2-,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    00: 86 80 d0 27 04 05 10 00 02 00 04 06 08 00 81 00
    10: 00 00 00 00 00 00 00 00 00 04 04 00 f0 00 00 20
    20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
    30: 00 00 00 00 40 00 00 00 00 00 00 00 05 01 02 00

    00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express
    Port 2 (rev 02) (prog-if 00 [Normal decode])
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
    ParErr- Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0, Cache Line Size: 32 bytes
    Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
    Memory behind bridge: fe700000-fe7fffff
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort+ <SERR- <PERR-
    BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
    Capabilities: [40] Express Root Port (Slot+) IRQ 0
    Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
    ExtTag-
    Device: Latency L0s unlimited, L1 unlimited
    Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
    Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
    Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
    Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 2
    Link: Latency L0s <256ns, L1 <4us
    Link: ASPM L1 Enabled RCB 64 bytes CommClk+ ExtSynch-
    Link: Speed 2.5Gb/s, Width x1
    Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+
    Surpise+
    Slot: Number 0, PowerLimit 0.000000
    Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
    Slot: AttnInd Unknown, PwrInd Unknown, Power-
    Root: Correctable- Non-Fatal- Fatal- PME-
    Capabilities: [80] Message Signalled Interrupts: 64bit-
    Queue=0/0 Enable+
    Address: fee00000 Data: 40d1
    Capabilities: [90] #0d [0000]
    Capabilities: [a0] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    PME(D0+,D1-,D2-,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    00: 86 80 d2 27 06 05 10 00 02 00 04 06 08 00 81 00
    10: 00 00 00 00 00 00 00 00 00 03 03 00 f0 00 00 20
    20: 70 fe 70 fe f1 ff 01 00 00 00 00 00 00 00 00 00
    30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 02 02 00

    00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express
    Port 3 (rev 02) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
    ParErr- Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0, Cache Line Size: 32 bytes
    Bus: primary=00, secondary=01, subordinate=02, sec-latency=0
    I/O behind bridge: 0000c000-0000cfff
    Memory behind bridge: fdf00000-fe6fffff
    Prefetchable memory behind bridge: 00000000bdf00000-00000000bfe00000
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- <SERR- <PERR-
    BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
    Capabilities: [40] Express Root Port (Slot+) IRQ 0
    Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
    ExtTag-
    Device: Latency L0s unlimited, L1 unlimited
    Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
    Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
    Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
    Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 3
    Link: Latency L0s <1us, L1 <4us
    Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
    Link: Speed 2.5Gb/s, Width x0
    Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+
    Surpise+
    Slot: Number 0, PowerLimit 0.000000
    Slot: Enabled AtnBtn+ PwrFlt- MRL- PresDet+ CmdCplt- HPIrq-
    Slot: AttnInd Unknown, PwrInd Unknown, Power-
    Root: Correctable- Non-Fatal- Fatal- PME-
    Capabilities: [80] Message Signalled Interrupts: 64bit-
    Queue=0/0 Enable+
    Address: fee00000 Data: 40d9
    Capabilities: [90] #0d [0000]
    Capabilities: [a0] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    PME(D0+,D1-,D2-,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    00: 86 80 d4 27 07 05 10 00 02 00 04 06 08 00 81 00
    10: 00 00 00 00 00 00 00 00 00 01 02 00 c0 c0 00 00
    20: f0 fd 60 fe f1 bd e1 bf 00 00 00 00 00 00 00 00
    30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 03 02 00

    00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
    #1 (rev 02) (prog-if 00 [UHCI])
    Subsystem: ASUSTeK Computer Inc. Unknown device 1347
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
    ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin A routed to IRQ 225
    Region 4: I/O ports at e400 [size=32]
    00: 86 80 c8 27 05 00 80 02 02 00 03 0c 00 00 80 00
    10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
    20: 01 e4 00 00 00 00 00 00 00 00 00 00 43 10 47 13
    30: 00 00 00 00 00 00 00 00 00 00 00 00 03 01 00 00

    00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
    #2 (rev 02) (prog-if 00 [UHCI])
    Subsystem: ASUSTeK Computer Inc. Unknown device 1347
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
    ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin B routed to IRQ 233
    Region 4: I/O ports at e480 [size=32]
    00: 86 80 c9 27 05 00 80 02 02 00 03 0c 00 00 00 00
    10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
    20: 81 e4 00 00 00 00 00 00 00 00 00 00 43 10 47 13
    30: 00 00 00 00 00 00 00 00 00 00 00 00 07 02 00 00

    00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
    #3 (rev 02) (prog-if 00 [UHCI])
    Subsystem: ASUSTeK Computer Inc. Unknown device 1347
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
    ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin C routed to IRQ 185
    Region 4: I/O ports at e800 [size=32]
    00: 86 80 ca 27 05 00 80 02 02 00 03 0c 00 00 00 00
    10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
    20: 01 e8 00 00 00 00 00 00 00 00 00 00 43 10 47 13
    30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 03 00 00

    00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
    #4 (rev 02) (prog-if 00 [UHCI])
    Subsystem: ASUSTeK Computer Inc. Unknown device 1347
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
    ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin D routed to IRQ 169
    Region 4: I/O ports at e880 [size=32]
    00: 86 80 cb 27 05 00 80 02 02 00 03 0c 00 00 00 00
    10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
    20: 81 e8 00 00 00 00 00 00 00 00 00 00 43 10 47 13
    30: 00 00 00 00 00 00 00 00 00 00 00 00 05 04 00 00

    00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI
    Controller (rev 02) (prog-if 20 [EHCI])
    Subsystem: ASUSTeK Computer Inc. Unknown device 1347
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
    ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin A routed to IRQ 225
    Region 0: Memory at feb3fc00 (32-bit, non-prefetchable) [size=1K]
    Capabilities: [50] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
    PME(D0+,D1-,D2-,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [58] Debug port
    00: 86 80 cc 27 06 00 90 02 02 20 03 0c 00 00 00 00
    10: 00 fc b3 fe 00 00 00 00 00 00 00 00 00 00 00 00
    20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 47 13
    30: 00 00 00 00 50 00 00 00 00 00 00 00 03 01 00 00

    00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
    (prog-if 01 [Subtractive decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
    ParErr- Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
    I/O behind bridge: 0000d000-0000dfff
    Memory behind bridge: fe800000-fe8fffff
    Prefetchable memory behind bridge: 0000000080000000-0000000080000000
    Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort+ <SERR- <PERR-
    BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
    Capabilities: [50] #0d [0000]
    00: 86 80 48 24 07 01 10 00 e2 01 04 06 00 00 01 00
    10: 00 00 00 00 00 00 00 00 00 05 05 20 d0 d0 80 22
    20: 80 fe 80 fe 01 80 01 80 00 00 00 00 00 00 00 00
    30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 02 00

    00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface
    Bridge (rev 02)
    Subsystem: ASUSTeK Computer Inc. Unknown device 1347
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
    ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Capabilities: [e0] Vendor Specific Information
    00: 86 80 b9 27 07 00 10 02 02 00 01 06 00 00 80 00
    10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
    20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 47 13
    30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00

    00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family)
    Serial ATA Storage Controller IDE (rev 02) (prog-if 80 [Master])
    Subsystem: ASUSTeK Computer Inc. Unknown device 1347
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
    ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin B routed to IRQ 233
    Region 0: I/O ports at <unassigned>
    Region 1: I/O ports at <unassigned>
    Region 2: I/O ports at <unassigned>
    Region 3: I/O ports at <unassigned>
    Region 4: I/O ports at ffa0 [size=16]
    Capabilities: [70] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot+,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    00: 86 80 c4 27 05 00 b8 02 02 80 01 01 00 00 00 00
    10: 01 00 00 00 01 00 00 00 01 00 00 00 01 00 00 00
    20: a1 ff 00 00 00 00 00 00 00 00 00 00 43 10 47 13
    30: 00 00 00 00 70 00 00 00 00 00 00 00 00 02 00 00

    00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller
    (rev 02)
    Subsystem: ASUSTeK Computer Inc. Unknown device 1347
    Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
    ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Interrupt: pin B routed to IRQ 233
    Region 4: I/O ports at 0400 [size=32]
    00: 86 80 da 27 01 00 80 02 02 00 05 0c 00 00 00 00
    10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
    20: 01 04 00 00 00 00 00 00 00 00 00 00 43 10 47 13
    30: 00 00 00 00 00 00 00 00 00 00 00 00 07 02 00 00

    03:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG
    Network Connection (rev 02)
    Subsystem: Intel Corporation Unknown device 1000
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
    ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0, Cache Line Size: 32 bytes
    Interrupt: pin A routed to IRQ 177
    Region 0: Memory at fe7ff000 (32-bit, non-prefetchable) [size=4K]
    Capabilities: [c8] Power Management version 2
    Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
    PME(D0+,D1-,D2-,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [d0] Message Signalled Interrupts: 64bit+
    Queue=0/0 Enable-
    Address: 0000000000000000 Data: 0000
    Capabilities: [e0] Express Legacy Endpoint IRQ 0
    Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
    ExtTag-
    Device: Latency L0s <512ns, L1 unlimited
    Device: AtnBtn- AtnInd- PwrInd-
    Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
    Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
    Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
    Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
    Link: Latency L0s <128ns, L1 <64us
    Link: ASPM L1 Enabled RCB 64 bytes CommClk+ ExtSynch-
    Link: Speed 2.5Gb/s, Width x1
    00: 86 80 22 42 06 00 10 00 02 00 80 02 08 00 00 00
    10: 00 f0 7f fe 00 00 00 00 00 00 00 00 00 00 00 00
    20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 00 10
    30: 00 00 00 00 c8 00 00 00 00 00 00 00 0a 01 00 00

    05:01.0 FireWire (IEEE 1394): Ricoh Co Ltd Unknown device 0832 (prog-if
    10 [OHCI])
    Subsystem: ASUSTeK Computer Inc. Unknown device 1347
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
    ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 64 (500ns min, 1000ns max)
    Interrupt: pin A routed to IRQ 169
    Region 0: Memory at fe8fe800 (32-bit, non-prefetchable) [size=2K]
    Capabilities: [dc] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    PME(D0+,D1-,D2-,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=2 PME+
    00: 80 11 32 08 06 00 10 02 00 10 00 0c 00 40 80 00
    10: 00 e8 8f fe 00 00 00 00 00 00 00 00 00 00 00 00
    20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 47 13
    30: 00 00 00 00 dc 00 00 00 00 00 00 00 05 01 02 04

    05:01.1 Class 0805: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host
    Adapter (rev 19)
    Subsystem: ASUSTeK Computer Inc. Unknown device 1347
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
    ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 64
    Interrupt: pin B routed to IRQ 177
    Region 0: Memory at fe8ff000 (32-bit, non-prefetchable) [size=256]
    Capabilities: [80] Power Management version 2
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
    PME(D0+,D1+,D2+,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=2 PME-
    00: 80 11 22 08 06 00 10 02 19 00 05 08 00 40 80 00
    10: 00 f0 8f fe 00 00 00 00 00 00 00 00 00 00 00 00
    20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 47 13
    30: 00 00 00 00 80 00 00 00 00 00 00 00 0a 02 00 00

    05:01.2 System peripheral: Ricoh Co Ltd Unknown device 0843 (rev 01)
    Subsystem: ASUSTeK Computer Inc. Unknown device 1347
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
    ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin B routed to IRQ 10
    Region 0: Memory at fe8ff400 (32-bit, non-prefetchable) [size=256]
    Capabilities: [80] Power Management version 2
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
    PME(D0+,D1+,D2+,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=2 PME-
    00: 80 11 43 08 06 00 10 02 01 00 80 08 00 00 80 00
    10: 00 f4 8f fe 00 00 00 00 00 00 00 00 00 00 00 00
    20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 47 13
    30: 00 00 00 00 80 00 00 00 00 00 00 00 0a 02 00 00

    05:01.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host
    Adapter (rev 0a)
    Subsystem: ASUSTeK Computer Inc. Unknown device 1347
    Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
    ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Interrupt: pin B routed to IRQ 10
    Region 0: Memory at fe8ff800 (32-bit, non-prefetchable) [size=256]
    Capabilities: [80] Power Management version 2
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
    PME(D0+,D1+,D2+,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=2 PME-
    00: 80 11 92 05 02 00 10 02 0a 00 80 08 00 00 80 00
    10: 00 f8 8f fe 00 00 00 00 00 00 00 00 00 00 00 00
    20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 47 13
    30: 00 00 00 00 80 00 00 00 00 00 00 00 0a 02 00 00

    05:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169SC
    Gigabit Ethernet (rev 10)
    Subsystem: ASUSTeK Computer Inc. Unknown device 1345
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
    ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes
    Interrupt: pin A routed to IRQ 11
    Region 0: I/O ports at d800 [size=256]
    Region 1: Memory at fe8ffc00 (32-bit, non-prefetchable) [size=256]
    Expansion ROM at 80000000 [disabled] [size=128K]
    Capabilities: [dc] Power Management version 2
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
    PME(D0-,D1+,D2+,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    00: ec 10 67 81 17 00 b0 02 10 00 00 02 08 40 00 00
    10: 01 d8 00 00 00 fc 8f fe 00 00 00 00 00 00 00 00
    20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 45 13
    30: 00 00 8c fe dc 00 00 00 00 00 00 00 0b 01 20 40

    Linux version 2.6.18-1.2798.fc6
    (brewbuilder@hs20-bc2-4.build.redhat.com) (gcc version 4.1.1 20061011
    (Red Hat 4.1.1-30)) #1 SMP Mon Oct 16 14:37:32 EDT 2006
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000007f7b0000 (usable)
    BIOS-e820: 000000007f7b0000 - 000000007f7be000 (ACPI data)
    BIOS-e820: 000000007f7be000 - 000000007f7f0000 (ACPI NVS)
    BIOS-e820: 000000007f7f0000 - 000000007f800000 (reserved)
    BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
    BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
    1143MB HIGHMEM available.
    896MB LOWMEM available.
    found SMP MP-table at 000ff780
    Using x86 segment limits to approximate NX protection
    On node 0 totalpages: 522160
    DMA zone: 4096 pages, LIFO batch:0
    Normal zone: 225280 pages, LIFO batch:31
    HighMem zone: 292784 pages, LIFO batch:31
    DMI present.
    Using APIC driver default
    ACPI: RSDP (v000 ACPIAM ) @ 0x000fb700
    ACPI: RSDT (v001 A M I OEMRSDT 0x08000629 MSFT 0x00000097) @ 0x7f7b0000
    ACPI: FADT (v002 A M I OEMFACP 0x08000629 MSFT 0x00000097) @ 0x7f7b0200
    ACPI: MADT (v001 A M I OEMAPIC 0x08000629 MSFT 0x00000097) @ 0x7f7b0390
    ACPI: MCFG (v001 A M I OEMMCFG 0x08000629 MSFT 0x00000097) @ 0x7f7b03f0
    ACPI: OEMB (v001 A M I AMI_OEM 0x08000629 MSFT 0x00000097) @ 0x7f7be040
    ACPI: DSDT (v001 A0544 A0544000 0x00000000 INTL 0x20060113) @ 0x00000000
    ACPI: PM-Timer IO Port: 0x808
    ACPI: Local APIC address 0xfee00000
    ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
    Processor #0 6:15 APIC version 20
    ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
    Processor #1 6:15 APIC version 20
    ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
    IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
    ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    ACPI: IRQ0 used by override.
    ACPI: IRQ2 used by override.
    ACPI: IRQ9 used by override.
    Enabling APIC mode: Flat. Using 1 I/O APICs
    Using ACPI (MADT) for SMP configuration information
    Allocating PCI resources starting at 80000000 (gap: 7f800000:7f600000)
    Detected 1828.934 MHz processor.
    Built 1 zonelists. Total pages: 522160
    Kernel command line: ro root=/dev/VolGroup00/LogVol00 ide1=dma ide1=ata66
    ide_setup: ide1=dma -- OBSOLETE OPTION, WILL BE REMOVED SOON!
    ide_setup: ide1=ata66 -- OBSOLETE OPTION, WILL BE REMOVED SOON!
    mapped APIC to ffffd000 (fee00000)
    mapped IOAPIC to ffffc000 (fec00000)
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Initializing CPU#0
    CPU 0 irqstacks, hard=c07ae000 soft=c078e000
    PID hash table entries: 4096 (order: 12, 16384 bytes)
    Console: colour VGA+ 80x25
    Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    Memory: 2063528k/2088640k available (2138k kernel code, 23752k reserved,
    868k data, 240k init, 1171136k highmem)
    Checking if this processor honours the WP bit even in supervisor mode... Ok.
    Calibrating delay using timer specific routine.. 3661.90 BogoMIPS
    (lpj=7323807)
    Security Framework v1.0.0 initialized
    SELinux: Initializing.
    SELinux: Starting in permissive mode
    selinux_register_security: Registering secondary module capability
    Capability LSM initialized as secondary
    Mount-cache hash table entries: 512
    CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000
    0000e3bd 00000000 00000001
    CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000
    0000e3bd 00000000 00000001
    monitor/mwait feature present.
    using mwait in idle threads.
    CPU: L1 I cache: 32K, L1 D cache: 32K
    CPU: L2 cache: 2048K
    CPU: Physical Processor ID: 0
    CPU: After all inits, caps: bfebf3ff 20100000 00000000 00000140 0000e3bd
    00000000 00000001
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    Checking 'hlt' instruction... OK.
    SMP alternatives: switching to UP code
    ACPI: Core revision 20060707
    ACPI Warning (utinit-0077): Invalid FADT value PM2_CNT_LEN=0 at offset
    5A FADT=f7ff8780 [20060707]
    CPU0: Intel(R) Core(TM)2 CPU T5600 @ 1.83GHz stepping 06
    SMP alternatives: switching to SMP code
    Booting processor 1/1 eip 3000
    CPU 1 irqstacks, hard=c07af000 soft=c078f000
    Initializing CPU#1
    Calibrating delay using timer specific routine.. 3657.79 BogoMIPS
    (lpj=7315581)
    CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000
    0000e3bd 00000000 00000001
    CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000
    0000e3bd 00000000 00000001
    monitor/mwait feature present.
    CPU: L1 I cache: 32K, L1 D cache: 32K
    CPU: L2 cache: 2048K
    CPU: Physical Processor ID: 0
    CPU: After all inits, caps: bfebf3ff 20100000 00000000 00000140 0000e3bd
    00000000 00000001
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#1.
    CPU1: Intel(R) Core(TM)2 CPU T5600 @ 1.83GHz stepping 06
    Total of 2 processors activated (7319.69 BogoMIPS).
    ENABLING IO-APIC IRQs
    ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
    checking TSC synchronization across 2 CPUs: passed.
    Brought up 2 CPUs
    sizeof(vma)=84 bytes
    sizeof(page)=32 bytes
    sizeof(inode)=424 bytes
    sizeof(dentry)=148 bytes
    sizeof(ext3inode)=600 bytes
    sizeof(buffer_head)=52 bytes
    sizeof(skbuff)=172 bytes
    sizeof(task_struct)=1392 bytes
    migration_cost=43
    checking if image is initramfs... it is
    Freeing initrd memory: 2119k freed
    NET: Registered protocol family 16
    ACPI: bus type pci registered
    PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
    PCI: Not using MMCONFIG.
    PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5
    PCI: Using configuration type 1
    Setting up standard PCI resources
    ACPI: Interpreter enabled
    ACPI: Using IOAPIC for interrupt routing
    ACPI: PCI Root Bridge [PCI0] (0000:00)
    PCI: Probing PCI hardware (bus 00)
    Boot video device is 0000:00:02.0
    PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2
    PCI: Transparent bridge - 0000:00:1e.0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
    ACPI: Embedded Controller [EC0] (gpe 28) interrupt mode.
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11 12 14 15)
    ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0,
    disabled.
    ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0,
    disabled.
    ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0,
    disabled.
    ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 10 11 12 14 15)
    Linux Plug and Play Support v0.97 (c) Adam Belay
    pnp: PnP ACPI init
    pnp: PnP ACPI: found 12 devices
    usbcore: registered new driver usbfs
    usbcore: registered new driver hub
    PCI: Using ACPI for IRQ routing
    PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
    report
    NetLabel: Initializing
    NetLabel: domain hash size = 128
    NetLabel: protocols = UNLABELED CIPSOv4
    NetLabel: unlabeled traffic allowed by default
    PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
    PCI: Bridge: 0000:00:1c.0
    IO window: disabled.
    MEM window: disabled.
    PREFETCH window: disabled.
    PCI: Bridge: 0000:00:1c.1
    IO window: disabled.
    MEM window: fe700000-fe7fffff
    PREFETCH window: disabled.
    PCI: Bridge: 0000:00:1c.2
    IO window: c000-cfff
    MEM window: fdf00000-fe6fffff
    PREFETCH window: bdf00000-bfefffff
    PCI: Bridge: 0000:00:1e.0
    IO window: d000-dfff
    MEM window: fe800000-fe8fffff
    PREFETCH window: 80000000-800fffff
    ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 169
    PCI: Setting latency timer of device 0000:00:1c.0 to 64
    ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 177
    PCI: Setting latency timer of device 0000:00:1c.1 to 64
    ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 185
    PCI: Setting latency timer of device 0000:00:1c.2 to 64
    PCI: Setting latency timer of device 0000:00:1e.0 to 64
    NET: Registered protocol family 2
    IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
    TCP established hash table entries: 131072 (order: 9, 2621440 bytes)
    TCP bind hash table entries: 65536 (order: 8, 1310720 bytes)
    TCP: Hash tables configured (established 131072 bind 65536)
    TCP reno registered
    apm: BIOS not found.
    audit: initializing netlink socket (disabled)
    audit(1163021534.932:1): initialized
    highmem bounce pool size: 64 pages
    Total HugeTLB memory allocated, 0
    VFS: Disk quotas dquot_6.5.1
    Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    SELinux: Registering netfilter hooks
    Initializing Cryptographic API
    ksign: Installing public key data
    Loading keyring
    - Added public key 8BDC589434DBC709
    - User ID: Red Hat, Inc. (Kernel Module GPG key)
    io scheduler noop registered
    io scheduler anticipatory registered
    io scheduler deadline registered
    io scheduler cfq registered (default)
    PCI: Setting latency timer of device 0000:00:1c.0 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[0000:00:1c.0:pcie00]
    Allocate Port Service[0000:00:1c.0:pcie02]
    PCI: Setting latency timer of device 0000:00:1c.1 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[0000:00:1c.1:pcie00]
    Allocate Port Service[0000:00:1c.1:pcie02]
    PCI: Setting latency timer of device 0000:00:1c.2 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[0000:00:1c.2:pcie00]
    Allocate Port Service[0000:00:1c.2:pcie02]
    pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ AMI] OemTableId [
    CPU1PM] [20060707]
    ACPI: CPU0 (power states: C1[C1] C2[C2])
    ACPI: Processor [CPU1] (supports 8 throttling states)
    ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ AMI] OemTableId [
    CPU2PM] [20060707]
    ACPI: CPU1 (power states: C1[C1] C2[C2])
    ACPI: Processor [CPU2] (supports 8 throttling states)
    ACPI: Thermal Zone [TZ00] (58 C)
    isapnp: Scanning for PnP cards...
    isapnp: No Plug & Play device found
    Real Time Clock Driver v1.12ac
    Non-volatile memory driver v1.2
    Linux agpgart interface v0.101 (c) Dave Jones
    agpgart: Detected an Intel 945GM Chipset.
    agpgart: Detected 7932K stolen memory.
    agpgart: AGP aperture is 256M @ 0xd0000000
    Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
    RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
    Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    ide0: I/O resource 0x1F0-0x1F7 not free.
    ide0: ports already in use, skipping probe
    Probing IDE interface ide1...
    hdc: HTS721060G9AT00, ATA DISK drive
    hdd: HL-DT-ST DVDRAM GMA-4082N, ATAPI CD/DVD-ROM drive
    Probing IDE interface ide2...
    Probing IDE interface ide3...
    Probing IDE interface ide4...
    Probing IDE interface ide5...
    ide1 at 0x170-0x177,0x376 on irq 15
    hdc: max request size: 512KiB
    hdc: 117210240 sectors (60011 MB) w/7539KiB Cache, CHS=16383/255/63
    hdc: cache flushes supported
    hdc: hdc1 hdc2
    ide-floppy driver 0.99.newide
    usbcore: registered new driver libusual
    usbcore: registered new driver hiddev
    usbcore: registered new driver usbhid
    drivers/usb/input/hid-core.c: v2.6:USB HID core driver
    PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
    i8042.c: Detected active multiplexing controller, rev 1.1.
    serio: i8042 AUX0 port at 0x60,0x64 irq 12
    serio: i8042 AUX1 port at 0x60,0x64 irq 12
    serio: i8042 AUX2 port at 0x60,0x64 irq 12
    serio: i8042 AUX3 port at 0x60,0x64 irq 12
    serio: i8042 KBD port at 0x60,0x64 irq 1
    mice: PS/2 mouse device common for all mice
    md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
    md: bitmap version 4.39
    TCP bic registered
    Initializing IPsec netlink socket
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    Using IPI No-Shortcut mode
    ACPI: (supports S0 S1 S3 S4 S5)
    Freeing unused kernel memory: 240k freed
    Write protecting the kernel read-only data: 386k
    Time: tsc clocksource has been installed.
    Time: acpi_pm clocksource has been installed.
    input: AT Translated Set 2 keyboard as /class/input/input0
    USB Universal Host Controller Interface driver v3.0
    ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 225
    PCI: Setting latency timer of device 0000:00:1d.0 to 64
    uhci_hcd 0000:00:1d.0: UHCI Host Controller
    uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
    uhci_hcd 0000:00:1d.0: irq 225, io base 0x0000e400
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 233
    PCI: Setting latency timer of device 0000:00:1d.1 to 64
    uhci_hcd 0000:00:1d.1: UHCI Host Controller
    uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
    uhci_hcd 0000:00:1d.1: irq 233, io base 0x0000e480
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185
    PCI: Setting latency timer of device 0000:00:1d.2 to 64
    uhci_hcd 0000:00:1d.2: UHCI Host Controller
    uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
    uhci_hcd 0000:00:1d.2: irq 185, io base 0x0000e800
    usb usb3: configuration #1 chosen from 1 choice
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 2 ports detected
    ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 169
    PCI: Setting latency timer of device 0000:00:1d.3 to 64
    uhci_hcd 0000:00:1d.3: UHCI Host Controller
    uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
    uhci_hcd 0000:00:1d.3: irq 169, io base 0x0000e880
    usb usb4: configuration #1 chosen from 1 choice
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 2 ports detected
    ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
    ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 225
    PCI: Setting latency timer of device 0000:00:1d.7 to 64
    ehci_hcd 0000:00:1d.7: EHCI Host Controller
    ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
    ehci_hcd 0000:00:1d.7: debug port 1
    PCI: cache line size of 32 is not supported by device 0000:00:1d.7
    ehci_hcd 0000:00:1d.7: irq 225, io mem 0xfeb3fc00
    ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
    usb usb5: configuration #1 chosen from 1 choice
    hub 5-0:1.0: USB hub found
    hub 5-0:1.0: 8 ports detected
    usb 2-2: new low speed USB device using uhci_hcd and address 2
    Synaptics Touchpad, model: 1, fw: 6.1, id: 0xa3a0b3, caps: 0xa04713/0x10008
    input: SynPS/2 Synaptics TouchPad as /class/input/input1
    device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised:
    dm-devel@redhat.com
    usb 2-2: new low speed USB device using uhci_hcd and address 3
    usb 2-2: configuration #1 chosen from 1 choice
    input: Logitech USB-PS/2 Trackball as /class/input/input2
    input: USB HID v1.00 Mouse [Logitech USB-PS/2 Trackball] on
    usb-0000:00:1d.1-2
    kjournald starting. Commit interval 5 seconds
    EXT3-fs: mounted filesystem with ordered data mode.
    security: 3 users, 6 roles, 1560 types, 166 bools, 1 sens, 1024 cats
    security: 58 classes, 48173 rules
    SELinux: Completing initialization.
    SELinux: Setting up existing superblocks.
    SELinux: initialized (dev dm-0, type ext3), uses xattr
    SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
    SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
    SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
    SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
    SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
    SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
    SELinux: initialized (dev devpts, type devpts), uses transition SIDs
    SELinux: initialized (dev eventpollfs, type eventpollfs), uses task SIDs
    SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
    SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
    SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
    SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
    SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
    SELinux: initialized (dev cpuset, type cpuset), not configured for labeling
    SELinux: initialized (dev proc, type proc), uses genfs_contexts
    SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
    SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
    SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
    audit(1163021543.452:2): policy loaded auid=4294967295
    input: PC Speaker as /class/input/input3
    ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 233
    sdhci: Secure Digital Host Controller Interface driver, 0.12
    sdhci: Copyright(c) Pierre Ossman
    sdhci: SDHCI controller found at 0000:05:01.1 [1180:0822] (rev 19)
    ACPI: PCI Interrupt 0000:05:01.1[B] -> GSI 17 (level, low) -> IRQ 177
    mmc0: SDHCI at 0xfe8ff000 irq 177 DMA
    SCSI subsystem initialized
    ieee1394: Initialized config rom entry `ip1394'
    ACPI: PCI Interrupt 0000:05:01.0[A] -> GSI 16 (level, low) -> IRQ 169
    libata version 2.00 loaded.
    ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[169]
    MMIO=[fe8fe800-fe8fefff] Max Packet=[2048] IR/IT contexts=[4/4]
    ata_piix 0000:00:1f.2: version 2.00
    ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
    ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 233
    ata: 0x170 IDE port busy
    PCI: Setting latency timer of device 0000:00:1f.2 to 64
    ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xFFA0 irq 14
    scsi0 : ata_piix
    ATA: abnormal status 0x7F on port 0x1F7
    hdd: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
    Uniform CD-ROM driver Revision: 3.20
    ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 169
    PCI: Setting latency timer of device 0000:00:1b.0 to 64
    hda_codec: Unknown model for ALC882, trying auto-probe from BIOS...
    ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e01800035ad155]
    floppy0: no floppy controllers found
    lp: driver loaded but no devices found
    ACPI: AC Adapter [AC0] (on-line)
    Asus Laptop ACPI Extras version 0.30
    Error calling BSTS
    unsupported model Z96F, trying default values
    send /proc/acpi/dsdt to the developers
    ACPI: Battery Slot [BAT0] (battery present)
    ACPI: Power Button (FF) [PWRF]
    ACPI: Lid Switch [LID]
    ACPI: Sleep Button (CM) [SLPB]
    ACPI: Power Button (CM) [PWRB]
    ibm_acpi: ec object not found
    ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
    md: Autodetecting RAID arrays.
    md: autorun ...
    md: ... autorun DONE.
    EXT3 FS on dm-0, internal journal
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on hdc1, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    SELinux: initialized (dev hdc1, type ext3), uses xattr
    SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
    Adding 1048568k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1
    across:1048568k
    SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses
    genfs_contexts
    SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
    Bluetooth: Core ver 2.10
    NET: Registered protocol family 31
    Bluetooth: HCI device and connection manager initialized
    Bluetooth: HCI socket layer initialized
    Bluetooth: L2CAP ver 2.8
    Bluetooth: L2CAP socket layer initialized
    Bluetooth: RFCOMM socket layer initialized
    Bluetooth: RFCOMM TTY layer initialized
    Bluetooth: RFCOMM ver 1.8
    Bluetooth: HIDP (Human Interface Emulation) ver 1.1
    SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
    SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
    NET: Registered protocol family 10
    lo: Disabled Privacy Extensions
    IPv6 over IPv4 tunneling driver
    ip_tables: (C) 2000-2006 Netfilter Core Team
    Netfilter messages via NETLINK v0.30.
    ip_conntrack version 2.4 (8192 buckets, 65536 max) - 228 bytes per conntrack
    usb 5-2: new high speed USB device using ehci_hcd and address 3
    usb 5-2: configuration #1 chosen from 1 choice
    Initializing USB Mass Storage driver...
    scsi1 : SCSI emulation for USB Mass Storage devices
    usb-storage: device found at 3
    usb-storage: waiting for device to settle before scanning
    usbcore: registered new driver usb-storage
    USB Mass Storage support registered.
    Vendor: Ut161 Model: USB2FlashStorage Rev: 0.00
    Type: Direct-Access ANSI SCSI revision: 02
    usb-storage: device scan complete
    scsi 1:0:0:0: Attached scsi generic sg0 type 0
    SCSI device sda: 1003520 512-byte hdwr sectors (514 MB)
    sda: Write Protect is off
    sda: Mode Sense: 00 00 00 00
    sda: assuming drive cache: write through
    SCSI device sda: 1003520 512-byte hdwr sectors (514 MB)
    sda: Write Protect is off
    sda: Mode Sense: 00 00 00 00
    sda: assuming drive cache: write through
    sda: unknown partition table
    sd 1:0:0:0: Attached scsi removable disk sda
    SELinux: initialized (dev sda, type vfat), uses genfs_contexts

    --

    "They that give up essential liberty to obtain temporary safety,
    deserve neither liberty nor safety." (Ben Franklin)

    "The course of history shows that as a government grows, liberty
    decreases." (Thomas Jefferson)



    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

    \
     
     \ /
      Last update: 2006-11-08 20:43    [W:0.106 / U:0.036 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site