![]() | ||||||||||
Messages in this thread |
Hi all, Hi Jeff, > My pb : I have a > 00:09.0 Mass storage controller: Promise Technology, Inc. PDC20375 > (SATA150 TX2plus) (rev 02) that worked (under kubuntu) and here > doesn't work with new install. > > I've a 160 Gb IDE disk on it. (My mother card don't accept such huge > disk without this card) So, I've investigated to see why UBUNTU Dapper see my IDE disk and why newer kernels doesn't. There's some big changes in dmesg : a sata_promise PATA port is found. Or it's on this port IDE disk is plugged. ---------------------- ubuntu's dmesg [17179580.780000] SCSI subsystem initialized [17179580.792000] ACPI: bus type scsi registered [17179580.792000] libata version 1.20 loaded. [17179580.800000] sata_promise 0000:00:09.0: version 1.03 [17179580.800000] **** SET: Misaligned resource pointer: d6a7d1e2 Type 07 Len 0 [17179580.804000] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 9 [17179580.804000] PCI: setting IRQ 9 as level-triggered [17179580.804000] ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKD] -> GSI 9 (level, low) -> IRQ 9 [17179580.804000] sata_promise PATA port found [17179580.820000] ata1: SATA max UDMA/133 cmd 0xD8880200 ctl 0xD8880238 bmdma 0x0 irq 9 [17179580.820000] ata2: SATA max UDMA/133 cmd 0xD8880280 ctl 0xD88802B8 bmdma 0x0 irq 9 [17179580.820000] ata3: PATA max UDMA/133 cmd 0xD8880300 ctl 0xD8880338 bmdma 0x0 irq 9 [17179581.024000] ata1: no device found (phy stat 00000000) [17179581.024000] scsi0 : sata_promise [17179581.228000] ata2: no device found (phy stat 00000000) [17179581.228000] scsi1 : sata_promise [17179581.392000] ata3: dev 0 cfg 00:0040 49:2f00 82:7c6b 83:7f09 84:4003 85:7c68 86:3e01 87:4003 88:407f 93:600b [17179581.392000] ata3: dev 0 ATA-7, max UDMA/133, 320173056 sectors: LBA48 [17179581.392000] ata3: dev 0 configured for UDMA/133 [17179581.392000] sata_get_dev_handle: SATA dev addr=0x90000, handle=0x00000000 [17179581.392000] scsi2 : sata_promise [17179581.392000] Vendor: ATA Model: Maxtor 6Y160P0 Rev: YAR4 [17179581.392000] Type: Direct-Access ANSI SCSI revision: 05 [17179581.420000] Driver 'sd' needs updating - please use bus_type methods [17179581.424000] SCSI device sda: 320173056 512-byte hdwr sectors (163929 MB) [17179581.424000] SCSI device sda: drive cache: write back [17179581.432000] SCSI device sda: 320173056 512-byte hdwr sectors (163929 MB) [17179581.436000] SCSI device sda: drive cache: write back [17179581.436000] sda: sda1 sda2 --------------------- Dmesg on 2.6.18.1 : scsi_mod: exports duplicate symbol scsi_logging_level (owned by kernel) libata version 2.00 loaded. sata_promise 0000:00:09.0: version 1.04 ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKD] -> GSI 9 (level, low) -> IRQ 9 ata1: SATA max UDMA/133 cmd 0xD8876200 ctl 0xD8876238 bmdma 0x0 irq 9 ata2: SATA max UDMA/133 cmd 0xD8876280 ctl 0xD88762B8 bmdma 0x0 irq 9 scsi0 : sata_promise ata1: SATA link down (SStatus 0 SControl 300) scsi1 : sata_promise ata2: SATA link down (SStatus 0 SControl 300) --------------------- Is there any PATA support broken in new sata_promise/libata stuff ? Is there any good kernel configuration in order to make it works? Thanks a lot. Jean-Baptiste - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/ | |||||||||
| Last update: 2006-11-06 06:43 [from the cache] ©2003-2008 | ||||||||||