lkml.org 
[lkml]   [2006]   [Nov]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Subjectpdc202xx_old+suspend+smartctl -> hard lockup
Date
Hello, if I run
smartctl -s on /dev/hde
after suspending my machine to ram (echo mem > /sys/power/state), it locks
up with nothing on serial console, and no sysrq.
If I move hde to hdd, I don't have the problem, so I suspect the problem
comes from my (on board) pdc20265 ide controller and not the drive.
This is a fc6 system running a vanilla 2.6.18 kernel (the fc kernels have
the same issue) and smartd disabled.
Tobias
========================
tobsbox:~# lspci -vvv
00:00.0 Host bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333]
Subsystem: ASUSTeK Computer Inc. A7V266-E Mainboard
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR+
Latency: 0
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW-
Rate=x4
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:01.0 PCI bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333
AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: ef000000-efdfffff
Prefetchable memory behind bridge: eff00000-f7ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:05.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
Subsystem: ASUSTeK Computer Inc. CMI8738 6ch-MX
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at b800 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:06.0 Mass storage controller: Promise Technology, Inc. PDC20265
(FastTrak100 Lite/Ultra100) (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 8042
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at b400 [size=8]
Region 1: I/O ports at b000 [size=4]
Region 2: I/O ports at a800 [size=8]
Region 3: I/O ports at a400 [size=4]
Region 4: I/O ports at a000 [size=64]
Region 5: Memory at ee800000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at 30000000 [size=64K]
Capabilities: [58] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Lite-On Communications Inc Unknown device 3104
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 9000 [disabled] [size=256]
Region 1: Memory at ee000000 (32-bit, non-prefetchable) [disabled]
[size=256]

00:0e.0 Ethernet controller: Atheros Communications, Inc. AR5005G 802.11abg
NIC (rev 01)
Subsystem: D-Link System Inc D-Link AirPlus G DWL-G510 Wireless PCI
Adapter(rev.B)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168 (2500ns min, 7000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at ed800000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-

00:10.0 Serial controller: 3Com Corp, Modem Division 56K FaxModem Model 5610
(rev 01) (prog-if 02 [16550])
Subsystem: 3Com Corp, Modem Division USR 56k Internal FAX Modem
(Model 2977)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at 9400 [size=8]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA
PME(D0+,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-

00:11.0 ISA bridge: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
Subsystem: ASUSTeK Computer Inc. VT8233A
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a
[Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. VT8233A Bus Master ATA100/66/33 IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at 1000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 1b) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at 8800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 1b) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at 8400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.4 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 1b) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at 8000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:00.0 VGA compatible controller: ATI Technologies Inc Radeon RV100 QY
[Radeon 7000/VE] (prog-if 00 [VGA])
Subsystem: PC Partner Limited RV100 QY [Sapphire Radeon VE 7000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at d800 [size=256]
Region 2: Memory at ef000000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at effe0000 [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW-
Rate=x4
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
========================
tobsbox:~# hdparm -I /dev/hde

/dev/hde:

ATA device, with non-removable media
Model Number: MAXTOR 6L060L3
Serial Number: 663128913879
Firmware Revision: A93.0500
Standards:
Used: ATA/ATAPI-5 T13 1321D revision 1
Supported: 5 4 3 & some of 6
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 117266688
device size with M = 1024*1024: 57259 MBytes
device size with M = 1000*1000: 60040 MBytes (60 GB)
Capabilities:
LBA, IORDY(can be disabled)
bytes avail on r/w long: 4
Standby timer values: spec'd by Vendor, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* DOWNLOAD_MICROCODE
SET_MAX security extension
* Automatic Acoustic Management feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* SMART error logging
* SMART self-test
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
30min for SECURITY ERASE UNIT.
HW reset results:
CBLID- above Vih
Device num = 0 determined by the jumper
Checksum: correct

_________________________________________________________________
Try the next generation of search with Windows Live Search today!
http://imagine-windowslive.com/minisites/searchlaunch/?locale=en-us&source=hmtagline

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2006-11-10 19:05    [W:0.204 / U:0.212 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site