lkml.org 
[lkml]   [2006]   [Jan]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: SMP+nosmp=hang [was: Re: 2.6.15-rc5-mm2]
On Fri, 20 Jan 2006 19:22:59 -0800, Andrew Morton <akpm@osdl.org> wrote:

> "J.A. Magallon" <jamagallon@able.es> wrote:
> >
> > On Sun, 11 Dec 2005 04:13:08 -0800, Andrew Morton <akpm@osdl.org> wrote:
> >
> > >
> > > ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.15-rc5/2.6.15-rc5-mm2/
> > >
> >
> > Booting a SMP built kernel with 'nosmp' just hangs at the VFS layer, with
> > the message about 'not being able to find root device sda1'.
> > sda is a SATA drive on an Intel ICH5 controller:
> >
> > libata version 1.20 loaded.
> > ata_piix 0000:00:1f.2: version 1.05
> > ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 16
> > PCI: Setting latency timer of device 0000:00:1f.2 to 64
> > ata1: SATA max UDMA/133 cmd 0xC000 ctl 0xC402 bmdma 0xD000 irq 16
> > ata2: SATA max UDMA/133 cmd 0xC800 ctl 0xCC02 bmdma 0xD008 irq 16
> > ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:407f
> > ata1: dev 0 ATA-6, max UDMA/133, 390721968 sectors: LBA48
> > ata1: dev 0 configured for UDMA/133
> > scsi0 : ata_piix
> > ATA: abnormal status 0x7F on port 0xC807
> > scsi1 : ata_piix
> > Vendor: ATA Model: ST3200822AS Rev: 3.01
> > Type: Direct-Access ANSI SCSI revision: 05
> > SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
> > SCSI device sda: drive cache: write back
> > SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
> > SCSI device sda: drive cache: write back
> > sda: sda1 sda2 sda3
> > sd 0:0:0:0: Attached scsi disk sda
> >
> > I would have to double check, but I think it even missed the USB keyboard.
> >
>
> Is this still happening?

Yes. I have just tried with 2.6.16-rc1-mm2, and the result is the same.
No root device.

The nosmp-booted kernel looks much much slow than the SMP one, it takes
ages to detect devices like usb ones, and even spent about 20 seconds here:

[ 0.431601] libata version 1.20 loaded.
[ 0.431652] ata_piix 0000:00:1f.2: version 1.05
[ 0.431670] ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 16
[ 0.431792] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 0.431852] ata1: SATA max UDMA/133 cmd 0xC000 ctl 0xC402 bmdma 0xD000 irq 16
[ 0.431950] ata2: SATA max UDMA/133 cmd 0xC800 ctl 0xCC02 bmdma 0xD008 irq 16
>>>>>>>>>>>>> here <<<<<<<<<<<<<<<<<<
[ 0.690451] ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:407f
[ 0.690456] ata1: dev 0 ATA-6, max UDMA/133, 390721968 sectors: LBA48
[ 0.696278] ata1: dev 0 configured for UDMA/133
[ 0.701627] scsi0 : ata_piix
[ 1.937443] scsi1 : ata_piix

and it did not detect any drive, so the no-root-device error. This one can be
a detection timeout, but as I say also the USB detection is dog slooow.

Need some info ? .config, or the like ?

--
J.A. Magallon <jamagallon()able!es> \ Software is like sex:
werewolf!able!es \ It's better when it's free
Mandriva Linux release 2006.1 (Cooker) for i586
Linux 2.6.15-jam5 (gcc 4.0.2 (4.0.2-1mdk for Mandriva Linux release 2006.1))
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2006-01-22 00:44    [W:3.061 / U:0.572 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site