Messages in this thread Patches in this message | | | Date | Sat, 21 Jan 2006 21:14:07 +0000 | From | Russell King <> | Subject | [CFT] Don't use ASYNC_* nor SERIAL_IO_* with serial_core |
| |
The serial_core layer has its own definitions for these, and I'd appreciate it if folk would use them instead of the old ASYNC_* and SERIAL_IO_* definitions.
They're compatible _at the moment_ but I make no guarantees that they will stay that way. Hence, it's in your interest to ensure that you're using the correct definitions.
MIPS, PPC seem to be the architectures which are stuck in the past on this issue, as is the M32R SIO driver.
The ioc4_serial driver is worse. It assumes that it can set/clear ASYNC_CTS_FLOW in the uart_info flags field, which is private to serial_core. It also seems to set TTY_IO_ERROR followed by immediately clearing it (pointless), and then it writes to tty->alt_speed... which isn't used by the serial layer so is also pointless.
So, here's a patch to fix some of this crap up. Please test and enjoy - I certainly didn't.
arch/mips/cobalt/setup.c | 2 +- arch/mips/lasat/setup.c | 4 ++-- arch/mips/mips-boards/atlas/atlas_setup.c | 4 ++-- arch/mips/mips-boards/sead/sead_setup.c | 4 ++-- arch/mips/mips-boards/sim/sim_setup.c | 4 ++-- arch/mips/momentum/jaguar_atx/ja-console.c | 2 +- arch/mips/pmc-sierra/yosemite/setup.c | 2 +- arch/mips/sgi-ip32/ip32-setup.c | 13 ++++--------- arch/ppc/platforms/4xx/bamboo.c | 4 ++-- arch/ppc/platforms/4xx/bubinga.c | 4 ++-- arch/ppc/platforms/4xx/ebony.c | 4 ++-- arch/ppc/platforms/4xx/luan.c | 4 ++-- arch/ppc/platforms/4xx/ocotea.c | 4 ++-- arch/ppc/platforms/4xx/xilinx_ml300.c | 4 ++-- arch/ppc/platforms/4xx/yucca.c | 4 ++-- arch/ppc/platforms/spruce.c | 4 ++-- drivers/serial/ioc4_serial.c | 14 -------------- drivers/serial/m32r_sio.c | 2 +- 18 files changed, 32 insertions(+), 51 deletions(-)
diff --git a/arch/mips/cobalt/setup.c b/arch/mips/cobalt/setup.c --- a/arch/mips/cobalt/setup.c +++ b/arch/mips/cobalt/setup.c @@ -139,7 +139,7 @@ void __init plat_setup(void) uart.type = PORT_UNKNOWN; uart.uartclk = 18432000; uart.irq = COBALT_SERIAL_IRQ; - uart.flags = STD_COM_FLAGS; + uart.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; uart.iobase = 0xc800000; uart.iotype = UPIO_PORT; diff --git a/arch/mips/lasat/setup.c b/arch/mips/lasat/setup.c --- a/arch/mips/lasat/setup.c +++ b/arch/mips/lasat/setup.c @@ -134,8 +134,8 @@ void __init serial_init(void) memset(&s, 0, sizeof(s)); - s.flags = STD_COM_FLAGS; - s.iotype = SERIAL_IO_MEM; + s.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; + s.iotype = UPIO_MEM; if (mips_machtype == MACH_LASAT_100) { s.uartclk = LASAT_BASE_BAUD_100 * 16; diff --git a/arch/mips/mips-boards/atlas/atlas_setup.c b/arch/mips/mips-boards/atlas/atlas_setup.c --- a/arch/mips/mips-boards/atlas/atlas_setup.c +++ b/arch/mips/mips-boards/atlas/atlas_setup.c @@ -82,8 +82,8 @@ static void __init serial_init(void) #endif s.irq = ATLASINT_UART; s.uartclk = ATLAS_BASE_BAUD * 16; - s.flags = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ; - s.iotype = SERIAL_IO_PORT; + s.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_AUTO_IRQ; + s.iotype = UPIO_PORT; s.regshift = 3; if (early_serial_setup(&s) != 0) { diff --git a/arch/mips/mips-boards/sead/sead_setup.c b/arch/mips/mips-boards/sead/sead_setup.c --- a/arch/mips/mips-boards/sead/sead_setup.c +++ b/arch/mips/mips-boards/sead/sead_setup.c @@ -71,8 +71,8 @@ static void __init serial_init(void) #endif s.irq = MIPSCPU_INT_BASE + MIPSCPU_INT_UART0; s.uartclk = SEAD_BASE_BAUD * 16; - s.flags = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ; - s.iotype = 0; + s.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_AUTO_IRQ; + s.iotype = UPIO_PORT; s.regshift = 3; if (early_serial_setup(&s) != 0) { diff --git a/arch/mips/mips-boards/sim/sim_setup.c b/arch/mips/mips-boards/sim/sim_setup.c --- a/arch/mips/mips-boards/sim/sim_setup.c +++ b/arch/mips/mips-boards/sim/sim_setup.c @@ -88,8 +88,8 @@ static void __init serial_init(void) but poll for now */ s.irq = 0; s.uartclk = BASE_BAUD * 16; - s.flags = ASYNC_BOOT_AUTOCONF | UPF_SKIP_TEST; - s.iotype = SERIAL_IO_PORT | ASYNC_SKIP_TEST; + s.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; + s.iotype = UPIO_PORT; s.regshift = 0; s.timeout = 4; diff --git a/arch/mips/momentum/jaguar_atx/ja-console.c b/arch/mips/momentum/jaguar_atx/ja-console.c --- a/arch/mips/momentum/jaguar_atx/ja-console.c +++ b/arch/mips/momentum/jaguar_atx/ja-console.c @@ -93,7 +93,7 @@ static void inline ja_console_probe(void up.uartclk = JAGUAR_ATX_UART_CLK; up.regshift = 2; up.iotype = UPIO_MEM; - up.flags = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST; + up.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; up.line = 0; if (early_serial_setup(&up)) diff --git a/arch/mips/pmc-sierra/yosemite/setup.c b/arch/mips/pmc-sierra/yosemite/setup.c --- a/arch/mips/pmc-sierra/yosemite/setup.c +++ b/arch/mips/pmc-sierra/yosemite/setup.c @@ -185,7 +185,7 @@ static void __init py_uart_setup(void) up.uartclk = TITAN_UART_CLK; up.regshift = 0; up.iotype = UPIO_MEM; - up.flags = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST; + up.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; up.line = 0; if (early_serial_setup(&up)) diff --git a/arch/mips/sgi-ip32/ip32-setup.c b/arch/mips/sgi-ip32/ip32-setup.c --- a/arch/mips/sgi-ip32/ip32-setup.c +++ b/arch/mips/sgi-ip32/ip32-setup.c @@ -66,11 +66,6 @@ static inline void str2eaddr(unsigned ch #include <linux/tty.h> #include <linux/serial.h> #include <linux/serial_core.h> -extern int early_serial_setup(struct uart_port *port); - -#define STD_COM_FLAGS (ASYNC_SKIP_TEST) -#define BASE_BAUD (1843200 / 16) - #endif /* CONFIG_SERIAL_8250 */ /* An arbitrary time; this can be decreased if reliability looks good */ @@ -110,8 +105,8 @@ void __init plat_setup(void) o2_serial[0].type = PORT_16550A; o2_serial[0].line = 0; o2_serial[0].irq = MACEISA_SERIAL1_IRQ; - o2_serial[0].flags = STD_COM_FLAGS; - o2_serial[0].uartclk = BASE_BAUD * 16; + o2_serial[0].flags = UPF_SKIP_TEST; + o2_serial[0].uartclk = 1843200; o2_serial[0].iotype = UPIO_MEM; o2_serial[0].membase = (char *)&mace->isa.serial1; o2_serial[0].fifosize = 14; @@ -121,8 +116,8 @@ void __init plat_setup(void) o2_serial[1].type = PORT_16550A; o2_serial[1].line = 1; o2_serial[1].irq = MACEISA_SERIAL2_IRQ; - o2_serial[1].flags = STD_COM_FLAGS; - o2_serial[1].uartclk = BASE_BAUD * 16; + o2_serial[1].flags = UPF_SKIP_TEST; + o2_serial[1].uartclk = 1843200; o2_serial[1].iotype = UPIO_MEM; o2_serial[1].membase = (char *)&mace->isa.serial2; o2_serial[1].fifosize = 14; diff --git a/arch/ppc/platforms/4xx/bamboo.c b/arch/ppc/platforms/4xx/bamboo.c --- a/arch/ppc/platforms/4xx/bamboo.c +++ b/arch/ppc/platforms/4xx/bamboo.c @@ -332,8 +332,8 @@ bamboo_early_serial_map(void) port.irq = 0; port.uartclk = clocks.uart0; port.regshift = 0; - port.iotype = SERIAL_IO_MEM; - port.flags = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST; + port.iotype = UPIO_MEM; + port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; port.line = 0; if (early_serial_setup(&port) != 0) { diff --git a/arch/ppc/platforms/4xx/bubinga.c b/arch/ppc/platforms/4xx/bubinga.c --- a/arch/ppc/platforms/4xx/bubinga.c +++ b/arch/ppc/platforms/4xx/bubinga.c @@ -97,8 +97,8 @@ bubinga_early_serial_map(void) port.irq = ACTING_UART0_INT; port.uartclk = uart_clock; port.regshift = 0; - port.iotype = SERIAL_IO_MEM; - port.flags = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST; + port.iotype = UPIO_MEM; + port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; port.line = 0; if (early_serial_setup(&port) != 0) { diff --git a/arch/ppc/platforms/4xx/ebony.c b/arch/ppc/platforms/4xx/ebony.c --- a/arch/ppc/platforms/4xx/ebony.c +++ b/arch/ppc/platforms/4xx/ebony.c @@ -225,8 +225,8 @@ ebony_early_serial_map(void) port.irq = 0; port.uartclk = clocks.uart0; port.regshift = 0; - port.iotype = SERIAL_IO_MEM; - port.flags = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST; + port.iotype = UPIO_MEM; + port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; port.line = 0; if (early_serial_setup(&port) != 0) { diff --git a/arch/ppc/platforms/4xx/luan.c b/arch/ppc/platforms/4xx/luan.c --- a/arch/ppc/platforms/4xx/luan.c +++ b/arch/ppc/platforms/4xx/luan.c @@ -279,8 +279,8 @@ luan_early_serial_map(void) port.irq = UART0_INT; port.uartclk = clocks.uart0; port.regshift = 0; - port.iotype = SERIAL_IO_MEM; - port.flags = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST; + port.iotype = UPIO_MEM; + port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; port.line = 0; if (early_serial_setup(&port) != 0) { diff --git a/arch/ppc/platforms/4xx/ocotea.c b/arch/ppc/platforms/4xx/ocotea.c --- a/arch/ppc/platforms/4xx/ocotea.c +++ b/arch/ppc/platforms/4xx/ocotea.c @@ -248,8 +248,8 @@ ocotea_early_serial_map(void) port.irq = UART0_INT; port.uartclk = clocks.uart0; port.regshift = 0; - port.iotype = SERIAL_IO_MEM; - port.flags = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST; + port.iotype = UPIO_MEM; + port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; port.line = 0; if (early_serial_setup(&port) != 0) { diff --git a/arch/ppc/platforms/4xx/xilinx_ml300.c b/arch/ppc/platforms/4xx/xilinx_ml300.c --- a/arch/ppc/platforms/4xx/xilinx_ml300.c +++ b/arch/ppc/platforms/4xx/xilinx_ml300.c @@ -95,8 +95,8 @@ ml300_early_serial_map(void) port.irq = old_ports[i].irq; port.uartclk = old_ports[i].baud_base * 16; port.regshift = old_ports[i].iomem_reg_shift; - port.iotype = SERIAL_IO_MEM; - port.flags = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST; + port.iotype = UPIO_MEM; + port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; port.line = i; if (early_serial_setup(&port) != 0) { diff --git a/arch/ppc/platforms/4xx/yucca.c b/arch/ppc/platforms/4xx/yucca.c --- a/arch/ppc/platforms/4xx/yucca.c +++ b/arch/ppc/platforms/4xx/yucca.c @@ -305,8 +305,8 @@ yucca_early_serial_map(void) port.irq = UART0_INT; port.uartclk = clocks.uart0; port.regshift = 0; - port.iotype = SERIAL_IO_MEM; - port.flags = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST; + port.iotype = UPIO_MEM; + port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; port.line = 0; if (early_serial_setup(&port) != 0) { diff --git a/arch/ppc/platforms/spruce.c b/arch/ppc/platforms/spruce.c --- a/arch/ppc/platforms/spruce.c +++ b/arch/ppc/platforms/spruce.c @@ -176,8 +176,8 @@ spruce_early_serial_map(void) memset(&serial_req, 0, sizeof(serial_req)); serial_req.uartclk = uart_clk; serial_req.irq = UART0_INT; - serial_req.flags = ASYNC_BOOT_AUTOCONF; - serial_req.iotype = SERIAL_IO_MEM; + serial_req.flags = UPF_BOOT_AUTOCONF; + serial_req.iotype = UPIO_MEM; serial_req.membase = (u_char *)UART0_IO_BASE; serial_req.regshift = 0; diff --git a/drivers/serial/ioc4_serial.c b/drivers/serial/ioc4_serial.c --- a/drivers/serial/ioc4_serial.c +++ b/drivers/serial/ioc4_serial.c @@ -1717,11 +1717,9 @@ ioc4_change_speed(struct uart_port *the_ } if (cflag & CRTSCTS) { - info->flags |= ASYNC_CTS_FLOW; port->ip_sscr |= IOC4_SSCR_HFC_EN; } else { - info->flags &= ~ASYNC_CTS_FLOW; port->ip_sscr &= ~IOC4_SSCR_HFC_EN; } writel(port->ip_sscr, &port->ip_serial_regs->sscr); @@ -1760,18 +1758,6 @@ static inline int ic4_startup_local(stru info = the_port->info; - if (info->tty) { - set_bit(TTY_IO_ERROR, &info->tty->flags); - clear_bit(TTY_IO_ERROR, &info->tty->flags); - if ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI) - info->tty->alt_speed = 57600; - if ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI) - info->tty->alt_speed = 115200; - if ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_SHI) - info->tty->alt_speed = 230400; - if ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_WARP) - info->tty->alt_speed = 460800; - } local_open(port); /* set the speed of the serial port */ diff --git a/drivers/serial/m32r_sio.c b/drivers/serial/m32r_sio.c --- a/drivers/serial/m32r_sio.c +++ b/drivers/serial/m32r_sio.c @@ -80,7 +80,7 @@ #include <asm/serial.h> /* Standard COM flags */ -#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST) +#define STD_COM_FLAGS (UPF_BOOT_AUTOCONF | UPF_SKIP_TEST) /* * SERIAL_PORT_DFNS tells us about built-in ports that have nodiff --git a/arch/mips/cobalt/setup.c b/arch/mips/cobalt/setup.c --- a/arch/mips/cobalt/setup.c +++ b/arch/mips/cobalt/setup.c @@ -139,7 +139,7 @@ void __init plat_setup(void) uart.type = PORT_UNKNOWN; uart.uartclk = 18432000; uart.irq = COBALT_SERIAL_IRQ; - uart.flags = STD_COM_FLAGS; + uart.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; uart.iobase = 0xc800000; uart.iotype = UPIO_PORT; diff --git a/arch/mips/lasat/setup.c b/arch/mips/lasat/setup.c --- a/arch/mips/lasat/setup.c +++ b/arch/mips/lasat/setup.c @@ -134,8 +134,8 @@ void __init serial_init(void) memset(&s, 0, sizeof(s)); - s.flags = STD_COM_FLAGS; - s.iotype = SERIAL_IO_MEM; + s.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; + s.iotype = UPIO_MEM; if (mips_machtype == MACH_LASAT_100) { s.uartclk = LASAT_BASE_BAUD_100 * 16; diff --git a/arch/mips/mips-boards/atlas/atlas_setup.c b/arch/mips/mips-boards/atlas/atlas_setup.c --- a/arch/mips/mips-boards/atlas/atlas_setup.c +++ b/arch/mips/mips-boards/atlas/atlas_setup.c @@ -82,8 +82,8 @@ static void __init serial_init(void) #endif s.irq = ATLASINT_UART; s.uartclk = ATLAS_BASE_BAUD * 16; - s.flags = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ; - s.iotype = SERIAL_IO_PORT; + s.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_AUTO_IRQ; + s.iotype = UPIO_PORT; s.regshift = 3; if (early_serial_setup(&s) != 0) { diff --git a/arch/mips/mips-boards/sead/sead_setup.c b/arch/mips/mips-boards/sead/sead_setup.c --- a/arch/mips/mips-boards/sead/sead_setup.c +++ b/arch/mips/mips-boards/sead/sead_setup.c @@ -71,8 +71,8 @@ static void __init serial_init(void) #endif s.irq = MIPSCPU_INT_BASE + MIPSCPU_INT_UART0; s.uartclk = SEAD_BASE_BAUD * 16; - s.flags = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ; - s.iotype = 0; + s.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_AUTO_IRQ; + s.iotype = UPIO_PORT; s.regshift = 3; if (early_serial_setup(&s) != 0) { diff --git a/arch/mips/mips-boards/sim/sim_setup.c b/arch/mips/mips-boards/sim/sim_setup.c --- a/arch/mips/mips-boards/sim/sim_setup.c +++ b/arch/mips/mips-boards/sim/sim_setup.c @@ -88,8 +88,8 @@ static void __init serial_init(void) but poll for now */ s.irq = 0; s.uartclk = BASE_BAUD * 16; - s.flags = ASYNC_BOOT_AUTOCONF | UPF_SKIP_TEST; - s.iotype = SERIAL_IO_PORT | ASYNC_SKIP_TEST; + s.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; + s.iotype = UPIO_PORT; s.regshift = 0; s.timeout = 4; diff --git a/arch/mips/momentum/jaguar_atx/ja-console.c b/arch/mips/momentum/jaguar_atx/ja-console.c --- a/arch/mips/momentum/jaguar_atx/ja-console.c +++ b/arch/mips/momentum/jaguar_atx/ja-console.c @@ -93,7 +93,7 @@ static void inline ja_console_probe(void up.uartclk = JAGUAR_ATX_UART_CLK; up.regshift = 2; up.iotype = UPIO_MEM; - up.flags = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST; + up.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; up.line = 0; if (early_serial_setup(&up)) diff --git a/arch/mips/pmc-sierra/yosemite/setup.c b/arch/mips/pmc-sierra/yosemite/setup.c --- a/arch/mips/pmc-sierra/yosemite/setup.c +++ b/arch/mips/pmc-sierra/yosemite/setup.c @@ -185,7 +185,7 @@ static void __init py_uart_setup(void) up.uartclk = TITAN_UART_CLK; up.regshift = 0; up.iotype = UPIO_MEM; - up.flags = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST; + up.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; up.line = 0; if (early_serial_setup(&up)) diff --git a/arch/mips/sgi-ip32/ip32-setup.c b/arch/mips/sgi-ip32/ip32-setup.c --- a/arch/mips/sgi-ip32/ip32-setup.c +++ b/arch/mips/sgi-ip32/ip32-setup.c @@ -66,11 +66,6 @@ static inline void str2eaddr(unsigned ch #include <linux/tty.h> #include <linux/serial.h> #include <linux/serial_core.h> -extern int early_serial_setup(struct uart_port *port); - -#define STD_COM_FLAGS (ASYNC_SKIP_TEST) -#define BASE_BAUD (1843200 / 16) - #endif /* CONFIG_SERIAL_8250 */ /* An arbitrary time; this can be decreased if reliability looks good */ @@ -110,8 +105,8 @@ void __init plat_setup(void) o2_serial[0].type = PORT_16550A; o2_serial[0].line = 0; o2_serial[0].irq = MACEISA_SERIAL1_IRQ; - o2_serial[0].flags = STD_COM_FLAGS; - o2_serial[0].uartclk = BASE_BAUD * 16; + o2_serial[0].flags = UPF_SKIP_TEST; + o2_serial[0].uartclk = 1843200; o2_serial[0].iotype = UPIO_MEM; o2_serial[0].membase = (char *)&mace->isa.serial1; o2_serial[0].fifosize = 14; @@ -121,8 +116,8 @@ void __init plat_setup(void) o2_serial[1].type = PORT_16550A; o2_serial[1].line = 1; o2_serial[1].irq = MACEISA_SERIAL2_IRQ; - o2_serial[1].flags = STD_COM_FLAGS; - o2_serial[1].uartclk = BASE_BAUD * 16; + o2_serial[1].flags = UPF_SKIP_TEST; + o2_serial[1].uartclk = 1843200; o2_serial[1].iotype = UPIO_MEM; o2_serial[1].membase = (char *)&mace->isa.serial2; o2_serial[1].fifosize = 14; diff --git a/arch/ppc/platforms/4xx/bamboo.c b/arch/ppc/platforms/4xx/bamboo.c --- a/arch/ppc/platforms/4xx/bamboo.c +++ b/arch/ppc/platforms/4xx/bamboo.c @@ -332,8 +332,8 @@ bamboo_early_serial_map(void) port.irq = 0; port.uartclk = clocks.uart0; port.regshift = 0; - port.iotype = SERIAL_IO_MEM; - port.flags = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST; + port.iotype = UPIO_MEM; + port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; port.line = 0; if (early_serial_setup(&port) != 0) { diff --git a/arch/ppc/platforms/4xx/bubinga.c b/arch/ppc/platforms/4xx/bubinga.c --- a/arch/ppc/platforms/4xx/bubinga.c +++ b/arch/ppc/platforms/4xx/bubinga.c @@ -97,8 +97,8 @@ bubinga_early_serial_map(void) port.irq = ACTING_UART0_INT; port.uartclk = uart_clock; port.regshift = 0; - port.iotype = SERIAL_IO_MEM; - port.flags = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST; + port.iotype = UPIO_MEM; + port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; port.line = 0; if (early_serial_setup(&port) != 0) { diff --git a/arch/ppc/platforms/4xx/ebony.c b/arch/ppc/platforms/4xx/ebony.c --- a/arch/ppc/platforms/4xx/ebony.c +++ b/arch/ppc/platforms/4xx/ebony.c @@ -225,8 +225,8 @@ ebony_early_serial_map(void) port.irq = 0; port.uartclk = clocks.uart0; port.regshift = 0; - port.iotype = SERIAL_IO_MEM; - port.flags = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST; + port.iotype = UPIO_MEM; + port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; port.line = 0; if (early_serial_setup(&port) != 0) { diff --git a/arch/ppc/platforms/4xx/luan.c b/arch/ppc/platforms/4xx/luan.c --- a/arch/ppc/platforms/4xx/luan.c +++ b/arch/ppc/platforms/4xx/luan.c @@ -279,8 +279,8 @@ luan_early_serial_map(void) port.irq = UART0_INT; port.uartclk = clocks.uart0; port.regshift = 0; - port.iotype = SERIAL_IO_MEM; - port.flags = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST; + port.iotype = UPIO_MEM; + port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; port.line = 0; if (early_serial_setup(&port) != 0) { diff --git a/arch/ppc/platforms/4xx/ocotea.c b/arch/ppc/platforms/4xx/ocotea.c --- a/arch/ppc/platforms/4xx/ocotea.c +++ b/arch/ppc/platforms/4xx/ocotea.c @@ -248,8 +248,8 @@ ocotea_early_serial_map(void) port.irq = UART0_INT; port.uartclk = clocks.uart0; port.regshift = 0; - port.iotype = SERIAL_IO_MEM; - port.flags = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST; + port.iotype = UPIO_MEM; + port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; port.line = 0; if (early_serial_setup(&port) != 0) { diff --git a/arch/ppc/platforms/4xx/xilinx_ml300.c b/arch/ppc/platforms/4xx/xilinx_ml300.c --- a/arch/ppc/platforms/4xx/xilinx_ml300.c +++ b/arch/ppc/platforms/4xx/xilinx_ml300.c @@ -95,8 +95,8 @@ ml300_early_serial_map(void) port.irq = old_ports[i].irq; port.uartclk = old_ports[i].baud_base * 16; port.regshift = old_ports[i].iomem_reg_shift; - port.iotype = SERIAL_IO_MEM; - port.flags = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST; + port.iotype = UPIO_MEM; + port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; port.line = i; if (early_serial_setup(&port) != 0) { diff --git a/arch/ppc/platforms/4xx/yucca.c b/arch/ppc/platforms/4xx/yucca.c --- a/arch/ppc/platforms/4xx/yucca.c +++ b/arch/ppc/platforms/4xx/yucca.c @@ -305,8 +305,8 @@ yucca_early_serial_map(void) port.irq = UART0_INT; port.uartclk = clocks.uart0; port.regshift = 0; - port.iotype = SERIAL_IO_MEM; - port.flags = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST; + port.iotype = UPIO_MEM; + port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST; port.line = 0; if (early_serial_setup(&port) != 0) { diff --git a/arch/ppc/platforms/spruce.c b/arch/ppc/platforms/spruce.c --- a/arch/ppc/platforms/spruce.c +++ b/arch/ppc/platforms/spruce.c @@ -176,8 +176,8 @@ spruce_early_serial_map(void) memset(&serial_req, 0, sizeof(serial_req)); serial_req.uartclk = uart_clk; serial_req.irq = UART0_INT; - serial_req.flags = ASYNC_BOOT_AUTOCONF; - serial_req.iotype = SERIAL_IO_MEM; + serial_req.flags = UPF_BOOT_AUTOCONF; + serial_req.iotype = UPIO_MEM; serial_req.membase = (u_char *)UART0_IO_BASE; serial_req.regshift = 0; diff --git a/drivers/serial/ioc4_serial.c b/drivers/serial/ioc4_serial.c --- a/drivers/serial/ioc4_serial.c +++ b/drivers/serial/ioc4_serial.c @@ -1717,11 +1717,9 @@ ioc4_change_speed(struct uart_port *the_ } if (cflag & CRTSCTS) { - info->flags |= ASYNC_CTS_FLOW; port->ip_sscr |= IOC4_SSCR_HFC_EN; } else { - info->flags &= ~ASYNC_CTS_FLOW; port->ip_sscr &= ~IOC4_SSCR_HFC_EN; } writel(port->ip_sscr, &port->ip_serial_regs->sscr); @@ -1760,18 +1758,6 @@ static inline int ic4_startup_local(stru info = the_port->info; - if (info->tty) { - set_bit(TTY_IO_ERROR, &info->tty->flags); - clear_bit(TTY_IO_ERROR, &info->tty->flags); - if ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI) - info->tty->alt_speed = 57600; - if ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI) - info->tty->alt_speed = 115200; - if ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_SHI) - info->tty->alt_speed = 230400; - if ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_WARP) - info->tty->alt_speed = 460800; - } local_open(port); /* set the speed of the serial port */ diff --git a/drivers/serial/m32r_sio.c b/drivers/serial/m32r_sio.c --- a/drivers/serial/m32r_sio.c +++ b/drivers/serial/m32r_sio.c @@ -80,7 +80,7 @@ #include <asm/serial.h> /* Standard COM flags */ -#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST) +#define STD_COM_FLAGS (UPF_BOOT_AUTOCONF | UPF_SKIP_TEST) /* * SERIAL_PORT_DFNS tells us about built-in ports that have no | |