lkml.org 
[lkml]   [2006]   [Jan]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: patch-2.6.15-rc7-rt2 (realtime-preempt) report
Hi,

[1.] One line summary of the problem:
I have got a lot of this ;)

[2.] Full description of the problem/report:
Everything is brooken. (Cool ;)

[3.] Keywords (i.e., modules, networking, kernel):
everything, rt3

[4.] Kernel version (from /proc/version):
Linux version 2.6.15-rc7-rt3 (michal@debian) (gcc version 4.0.3
20051201 (prerelease) (Debian 4.0.2-5)) #3 SMP PREEMPT Mon Jan 2
23:46:45 CET 2006

[5.] Most recent kernel version which did not have the bug:

[6.] Output of Oops
Console: colour VGA+ 80x25
----------------------------->
| new stack-footprint maximum: swapper/0, 788 bytes (out of 4044 bytes).
------------|
{ 24} [<c0138d99>] debug_stackoverflow+0x80/0xb2
{ 28} [<c013920e>] __mcount+0x37/0xa5
{ 20} [<c010f05c>] mcount+0x14/0x18
{ 124} [<c01c8917>] number+0xe/0x204
{ 76} [<c01c8f0b>] vsnprintf+0x3fe/0x438
{ 28} [<c01c8f60>] vscnprintf+0x1b/0x2b
{ 128} [<c011c5bc>] vprintk+0x7a/0x23d
{ 20} [<c011c540>] printk+0x18/0x1a
{ 172} [<c010f0ae>] MP_processor_info+0x4a/0x1b4
{ 36} [<c010f2b2>] mp_register_lapic+0x9a/0xa0
{ 24} [<c03e3d5d>] acpi_parse_lapic+0x45/0x56
{ 28} [<c03ee6c9>] acpi_table_parse_madt_family+0xb0/0x100
{ 28} [<c03ee733>] acpi_table_parse_madt+0x1a/0x1c
{ 32} [<c03e4129>] acpi_parse_madt_lapic_entries+0x49/0x9a
{ 8} [<c03e427c>] acpi_process_madt+0x23/0xb3
{ 24} [<c03e453f>] acpi_boot_init+0x3c/0x4c
{ 20} [<c03e15ae>] setup_arch+0x1af/0x1ed
{ 24} [<c03dd72f>] start_kernel+0x30/0x19a
<---------------------------
[snip]

Event source lapic installed with caps set: 06
BUG: swapper:0 task might have lost a preemption check!
Brought up 2 CPUs
[<c0103b27>] dump_stack+0x1b/0x1f (20)
[<c01196ab>] preempt_enable_no_resched+0x4a/0x4f (20)
[<c0100d8d>] cpu_idle+0xc7/0xdf (16)
[<c010eb0e>] start_secondary+0x2d3/0x2db (32)
[<00000000>] rest_init+0x3feffd68/0x45 (-4)
[<c199dfb4>] 0xc199dfb4 (1046880332)
---------------------------
| preempt count: 00000000 ]
| 0-level deep critical section nesting:
----------------------------------------
------------------------------
| showing all locks held by: | (swapper/0 [c1999020, 140]):
------------------------------
Linux NoNET1.0 for Linux 2.6
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
----------------------------->
| new stack-footprint maximum: swapper/1, 1624 bytes (out of 4044 bytes).
------------|
{ 24} [<c0138d99>] debug_stackoverflow+0x80/0xb2
{ 28} [<c013920e>] __mcount+0x37/0xa5
{ 20} [<c010f05c>] mcount+0x14/0x18
{ 24} [<c01c9438>] find_next_bit+0xc/0x81
{ 68} [<c011665c>] find_busiest_group+0x156/0x316
{ 56} [<c0116927>] load_balance+0x51/0x1e6
{ 52} [<c0116d4e>] rebalance_tick+0xcf/0xf1
{ 60} [<c01172d7>] scheduler_tick+0x362/0x36d
{ 20} [<c01247ec>] update_process_times+0xd4/0xff
{ 12} [<c0136f22>] handle_update+0x1b/0x1e
{ 12} [<c0136fb7>] handle_nextevent_update+0x19/0x1c
{ 16} [<c010fc29>] smp_apic_timer_interrupt+0x54/0x5f
{ 72} [<c01036fd>] apic_timer_interrupt+0x21/0x28
{ 28} [<c013920e>] __mcount+0x37/0xa5
{ 20} [<c010f05c>] mcount+0x14/0x18
{ 16} [<c024b462>] __lock_text_start+0xa/0x4f
{ 24} [<c015e14f>] kmem_cache_free+0x4a/0xae
{ 16} [<c01e7388>] acpi_os_release_object+0x13/0x17
{ 16} [<c01f7255>] acpi_ps_free_op+0x26/0x2a
{ 24} [<c01f6f7e>] acpi_ps_delete_parse_tree+0x36/0x50
{ 24} [<c01f63b3>] acpi_ps_complete_this_op+0x13e/0x15a
{ 52} [<c01f6beb>] acpi_ps_parse_loop+0x54b/0x7e8
{ 32} [<c01f6507>] acpi_ps_parse_aml+0x51/0x1ea
{ 24} [<c01e8168>] acpi_ds_execute_arguments+0xe0/0x102
{ 40} [<c01e82b3>] acpi_ds_get_region_arguments+0x3e/0x4d
{ 24} [<c01eec2b>] acpi_ex_setup_region+0x2b/0x76
{ 28} [<c01eec8d>] acpi_ex_access_region+0x17/0x96
{ 44} [<c01eee47>] acpi_ex_field_datum_io+0xfd/0x190
{ 72} [<c01ef04b>] acpi_ex_extract_from_field+0x81/0x209
{ 40} [<c01ed9cd>] acpi_ex_read_data_from_field+0x121/0x153
{ 36} [<c01f25b3>] acpi_ex_resolve_node_to_value+0xb7/0xec
{ 24} [<c01ee183>] acpi_ex_resolve_to_value+0x3f/0x57
{ 52} [<c01f02e3>] acpi_ex_resolve_operands+0x1bd/0x35a
{ 36} [<c01e8b9e>] acpi_ds_exec_end_op+0xa0/0x34a
{ 48} [<c01f6b9d>] acpi_ps_parse_loop+0x4fd/0x7e8
{ 32} [<c01f6507>] acpi_ps_parse_aml+0x51/0x1ea
{ 28} [<c01f73ee>] acpi_ps_execute_pass+0x7d/0x93
{ 20} [<c01f7304>] acpi_ps_execute_method+0x50/0x7b
{ 20} [<c01f4946>] acpi_ns_execute_control_method+0x49/0x5a
{ 16} [<c01f48de>] acpi_ns_evaluate_by_handle+0x7a/0x99
{ 32} [<c01f47c6>] acpi_ns_evaluate_relative+0xae/0xd2
{ 48} [<c01fb278>] acpi_ut_evaluate_object+0x2f/0x119
{ 40} [<c01ecd81>] acpi_ev_match_prw_and_gpe+0x22/0xc2
{ 48} [<c01f59ed>] acpi_ns_walk_namespace+0x83/0x10a
{ 56} [<c01ed292>] acpi_ev_create_gpe_block+0xc2/0xfa
{ 48} [<c01ed333>] acpi_ev_gpe_initialize+0x69/0x1b2
{ 12} [<c01eaa6f>] acpi_ev_initialize_events+0x43/0x72
{ 12} [<c01fc09c>] acpi_enable_subsystem+0x4c/0x5d
{ 12} [<c03eef3e>] acpi_bus_init+0x14/0x93
{ 12} [<c03ef000>] acpi_init+0x43/0x72
{ 20} [<c03dd8e8>] do_initcalls+0x4f/0xbc
{ 8} [<c03dd994>] do_basic_setup+0x26/0x28
{ 12} [<c01003d6>] init+0xa7/0x261
<---------------------------
[snip]

----------------------------->
| new stack-footprint maximum: swapper/1, 2020 bytes (out of 4044 bytes).
------------|
{ 24} [<c0138d99>] debug_stackoverflow+0x80/0xb2
{ 28} [<c013920e>] __mcount+0x37/0xa5
{ 20} [<c010f05c>] mcount+0x14/0x18
{ 24} [<c01c9438>] find_next_bit+0xc/0x81
{ 36} [<c01152f4>] wake_idle+0x8e/0xad
{ 72} [<c0115582>] try_to_wake_up+0x26f/0x482
{ 32} [<c01157b2>] wake_up_process+0x1d/0x2b
{ 12} [<c0120a9a>] wakeup_softirqd+0x33/0x36
{ 24} [<c0120d4e>] raise_softirq+0x59/0x78
{ 8} [<c012484c>] run_local_timers+0x12/0x14
{ 20} [<c0124797>] update_process_times+0x7f/0xff
{ 12} [<c0136f22>] handle_update+0x1b/0x1e
{ 12} [<c0136fb7>] handle_nextevent_update+0x19/0x1c
{ 16} [<c010fc29>] smp_apic_timer_interrupt+0x54/0x5f
{ 84} [<c01036fd>] apic_timer_interrupt+0x21/0x28
{ 24} [<c0149515>] prep_new_page+0x72/0x7e
{ 44} [<c014988d>] buffered_rmqueue+0xb8/0x176
{ 36} [<c0149a5b>] get_page_from_freelist+0x75/0x93
{ 64} [<c0149ade>] __alloc_pages+0x65/0x27c
{ 20} [<c015ce33>] kmem_getpages+0x5e/0xb3
{ 60} [<c015da69>] cache_grow+0xea/0x1d0
{ 52} [<c015dcde>] cache_alloc_refill+0x18f/0x1db
{ 36} [<c015def5>] kmem_cache_alloc+0x87/0xc4
{ 28} [<c0178187>] alloc_inode+0x2f/0x1ab
{ 20} [<c0178bdf>] new_inode+0x1c/0x97
{ 28} [<c019461d>] sysfs_new_inode+0x1a/0xe3
{ 36} [<c019471f>] sysfs_create+0x39/0xdf
{ 36} [<c0195401>] create_dir+0x80/0x18e
{ 32} [<c01955b4>] sysfs_create_dir+0x63/0x80
{ 20} [<c01c637b>] create_dir+0x1a/0x3e
{ 24} [<c01c657f>] kobject_add+0x81/0xa4
{ 40} [<c021c4b0>] class_device_add+0x98/0x204
{ 20} [<c021c634>] class_device_register+0x18/0x1d
{ 36} [<c02419ec>] i2c_add_adapter+0x17f/0x1c9
{ 16} [<c0243d87>] i2c_bit_add_bus+0x51/0x5b
{ 44} [<c01e632d>] nvidia_setup_i2c_bus+0xbc/0x10c
{ 20} [<c01e63c0>] nvidia_create_i2c_busses+0x43/0x81
{ 512} [<c01e4ccb>] NVCommonSetup+0x34f/0x9f8
{ 28} [<c01e1216>] nvidiafb_probe+0x320/0x512
{ 16} [<c01cec49>] pci_call_probe+0x14/0x16
{ 28} [<c01cec83>] __pci_device_probe+0x38/0x4b
{ 28} [<c01cecbc>] pci_device_probe+0x26/0x3f
{ 24} [<c021b79a>] driver_probe_device+0x3b/0x89
{ 24} [<c021b882>] __driver_attach+0x2c/0x3e
{ 40} [<c021af58>] <6>Time: tsc clocksource has been installed.
bus_for_each_dev+0x4a/0x71
{ 24} [<c021b8af>] driver_attach+0x1b/0x20
{ 28} [<c021b357>] bus_add_driver+0x6c/0xb8
{ 48} [<c021bc14>] driver_register+0x4e/0x55
{ 32} <6>hrtimers: Switched to high resolution mode CPU 1
[<c01ceeec>] __pci_register_driver+0x98/0xab
{ 24} <6>hrtimers: Switched to high resolution mode CPU 0
[<c01e16a6>] nvidiafb_init+0x3d/0x47
{ 20} [<c03dd8e8>] do_initcalls+0x4f/0xbc
{ 8} [<c03dd994>] do_basic_setup+0x26/0x28
{ 12} [<c01003d6>] init+0xa7/0x261
<---------------------------
[snip]
*****************************************************************************
* *
* REMINDER, the following debugging options are turned on in your .config: *
* *
* CONFIG_DEBUG_RT_LOCKING_MODE *
* CONFIG_DEBUG_DEADLOCKS *
* CONFIG_DEBUG_PREEMPT *
* CONFIG_CRITICAL_PREEMPT_TIMING *
* CONFIG_CRITICAL_IRQSOFF_TIMING *
* CONFIG_LATENCY_TRACE *
* CONFIG_DEBUG_PAGEALLOC *
* *
* they may increase runtime overhead and latencies. *
* *
*****************************************************************************
Freeing unused kernel memory: 404k freed
----------------------------->
| new stack-footprint maximum: init/1, 2032 bytes (out of 4044 bytes).
------------|
{ 24} [<c0138d99>] debug_stackoverflow+0x80/0xb2
{ 28} [<c013920e>] __mcount+0x37/0xa5
{ 20} [<c010f05c>] mcount+0x14/0x18
{ 12} [<c01c9769>] delay_tsc+0x9/0x1d
{ 12} [<c01c97ea>] __delay+0x11/0x14
{ 12} [<c01c9821>] __const_udelay+0x34/0x37
{ 16} [<c02355f5>] ata_std_dev_select+0x3b/0x3f
{ 28} [<c0235651>] ata_dev_select+0x58/0xc1
{ 32} [<c0238395>] ata_qc_issue_prot+0x1f/0x118
{ 24} [<c0238360>] ata_qc_issue+0x69/0x7f
{ 28} [<c023a541>] ata_scsi_translate+0xa5/0xd8
{ 44} [<c023b29e>] ata_scsi_queuecmd+0xfa/0x132
{ 32} [<c022c706>] scsi_dispatch_cmd+0x1a8/0x1fa
{ 32} [<c02313c9>] scsi_request_fn+0x23b/0x2e7
{ 16} [<c01be121>] __generic_unplug_device+0x28/0x2e
{ 16} [<c01be144>] generic_unplug_device+0x1d/0x2e
{ 12} [<c01be170>] blk_backing_dev_unplug+0x1b/0x1e
{ 16} [<c016249f>] sync_buffer+0x3a/0x45
{ 32} [<c02493dd>] __wait_on_bit+0x39/0x62
{ 60} [<c0249465>] out_of_line_wait_on_bit+0x5f/0x67
{ 16} [<c0162517>] __wait_on_buffer+0x25/0x2b
{ 16} [<c016375f>] __bread_slow+0x76/0x8d
{ 12} [<c01639ec>] __bread+0x2b/0x32
{ 48} [<c019a0bf>] ext3_get_branch+0x6a/0xea
{ 120} [<c019a5da>] ext3_get_block_handle+0xab/0x289
{ 40} [<c019a82d>] ext3_get_block+0x75/0x7c
{ 328} [<c0182136>] do_mpage_readpage+0x14d/0x383
{ 84} [<c01823e5>] mpage_readpages+0x79/0xf4
{ 24} [<c019b568>] ext3_readpages+0x1b/0x1d
{ 76} [<c014bf2a>] read_pages+0x2a/0xcd
{ 56} [<c014c11d>] __do_page_cache_readahead+0x150/0x185
{ 28} [<c014c206>] do_page_cache_readahead+0x40/0x4c
{ 60} [<c0146cfb>] filemap_nopage+0x148/0x2e8
{ 60} [<c015219f>] do_no_page+0x98/0x2a7
{ 48} [<c01524df>] __handle_mm_fault+0xc5/0x17d
{ 76} [<c011331e>] do_page_fault+0x16b/0x495
{ 80} [<c01037d3>] error_code+0x4f/0x54
{ 16} [<c0186fd5>] padzero+0x23/0x34
{ 48} [<c01875c7>] load_elf_interp+0x1eb/0x27b
{ 148} [<c0187f91>] load_elf_binary+0x7b1/0xaa2
{ 40} [<c016b9fe>] search_binary_handler+0xcc/0x299
{ 32} [<c016bd3c>] do_execve+0x171/0x21c
{ 36} [<c01019c7>] sys_execve+0x2f/0x7b
{=1988} [<c0102c72>] syscall_call+0x7/0xb
<---------------------------
[snip]

----------------------------->
| new stack-footprint maximum: rcS/292, 2060 bytes (out of 4044 bytes).
------------|
{ 24} [<c0138d99>] debug_stackoverflow+0x80/0xb2
{ 28} [<c013920e>] __mcount+0x37/0xa5
{ 20} [<c010f05c>] mcount+0x14/0x18
{ 24} [<c0113d89>] change_page_attr+0xc/0x53
{ 40} [<c0113f34>] kernel_map_pages+0x78/0xd8
{ 24} [<c0149515>] prep_new_page+0x72/0x7e
{ 44} [<c014988d>] buffered_rmqueue+0xb8/0x176
{ 36} [<c0149a5b>] get_page_from_freelist+0x75/0x93
{ 64} [<c0149ade>] __alloc_pages+0x65/0x27c
{ 28} [<c0146013>] find_or_create_page+0x6a/0xa4
{ 32} [<c0163425>] grow_dev_page+0x21/0x14d
{ 36} [<c016360d>] __getblk_slow+0xbc/0xe2
{ 32} [<c0163971>] __getblk+0x3d/0x4c
{ 20} [<c01639d7>] __bread+0x16/0x32
{ 48} [<c019a0bf>] ext3_get_branch+0x6a/0xea
{ 120} [<c019a5da>] ext3_get_block_handle+0xab/0x289
{ 40} [<c019a82d>] ext3_get_block+0x75/0x7c
{ 328} [<c0182136>] do_mpage_readpage+0x14d/0x383
{ 84} [<c01823e5>] mpage_readpages+0x79/0xf4
{ 24} [<c019b568>] ext3_readpages+0x1b/0x1d
{ 76} [<c014bf2a>] read_pages+0x2a/0xcd
{ 56} [<c014c11d>] __do_page_cache_readahead+0x150/0x185
{ 28} [<c014c206>] do_page_cache_readahead+0x40/0x4c
{ 60} [<c0146cfb>] filemap_nopage+0x148/0x2e8
{ 60} [<c015219f>] do_no_page+0x98/0x2a7
{ 48} [<c01524df>] __handle_mm_fault+0xc5/0x17d
{ 76} [<c011331e>] do_page_fault+0x16b/0x495
{ 80} [<c01037d3>] error_code+0x4f/0x54
{ 16} [<c0186fd5>] padzero+0x23/0x34
{ 140} [<c0187f35>] load_elf_binary+0x755/0xaa2
{ 40} [<c016b9fe>] search_binary_handler+0xcc/0x299
{ 164} [<c0186f0d>] load_script+0x195/0x1a8
{ 40} [<c016b9fe>] search_binary_handler+0xcc/0x299
{ 32} [<c016bd3c>] do_execve+0x171/0x21c
{ 36} [<c01019c7>] sys_execve+0x2f/0x7b
{=2048} [<c0102c04>] sysenter_past_esp+0x61/0x89
<---------------------------

[9.] Config file
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.15-rc7-rt3
# Mon Jan 2 23:46:13 2006
#
CONFIG_X86_32=y
CONFIG_GENERIC_TIME=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_X86=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y

#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_CLEAN_COMPILE=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32

#
# General setup
#
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_BSD_PROCESS_ACCT_V3=y
CONFIG_SYSCTL=y
CONFIG_HOTPLUG=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
# CONFIG_CPUSETS is not set
CONFIG_INITRAMFS_SOURCE=""
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
# CONFIG_EMBEDDED is not set
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SHMEM=y
CONFIG_CC_ALIGN_FUNCTIONS=0
CONFIG_CC_ALIGN_LABELS=0
CONFIG_CC_ALIGN_LOOPS=0
CONFIG_CC_ALIGN_JUMPS=0
CONFIG_SLAB=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
# CONFIG_SLOB is not set

#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_OBSOLETE_MODPARM=y
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
CONFIG_KMOD=y
CONFIG_STOP_MACHINE=y

#
# Block layer
#
# CONFIG_LBD is not set

#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=m
CONFIG_IOSCHED_CFQ=m
CONFIG_DEFAULT_AS=y
# CONFIG_DEFAULT_DEADLINE is not set
# CONFIG_DEFAULT_CFQ is not set
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="anticipatory"

#
# Processor type and features
#
CONFIG_X86_PC=y
# CONFIG_X86_ELAN is not set
# CONFIG_X86_VOYAGER is not set
# CONFIG_X86_NUMAQ is not set
# CONFIG_X86_SUMMIT is not set
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_VISWS is not set
# CONFIG_X86_GENERICARCH is not set
# CONFIG_X86_ES7000 is not set
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUMM is not set
CONFIG_MPENTIUM4=y
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MK8 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MEFFICEON is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MGEODEGX1 is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
# CONFIG_X86_GENERIC is not set
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_L1_CACHE_SHIFT=7
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_CMPXCHG64=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_TSC=y
# CONFIG_HPET_TIMER is not set
CONFIG_HIGH_RES_TIMERS=y
CONFIG_HIGH_RES_RESOLUTION=1000
CONFIG_SMP=y
CONFIG_NR_CPUS=2
CONFIG_SCHED_SMT=y
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set
# CONFIG_PREEMPT_DESKTOP is not set
CONFIG_PREEMPT_RT=y
CONFIG_PREEMPT=y
CONFIG_PREEMPT_SOFTIRQS=y
CONFIG_PREEMPT_HARDIRQS=y
CONFIG_PREEMPT_BKL=y
CONFIG_PREEMPT_RCU=y
CONFIG_RCU_STATS=y
CONFIG_ASM_SEMAPHORES=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_MCE=y
CONFIG_X86_MCE_NONFATAL=m
CONFIG_X86_MCE_P4THERMAL=y
# CONFIG_TOSHIBA is not set
# CONFIG_I8K is not set
# CONFIG_X86_REBOOTFIXUPS is not set
CONFIG_MICROCODE=m
CONFIG_X86_MSR=m
CONFIG_X86_CPUID=m

#
# Firmware Drivers
#
# CONFIG_EDD is not set
# CONFIG_DELL_RBU is not set
# CONFIG_DCDBAS is not set
# CONFIG_NOHIGHMEM is not set
CONFIG_HIGHMEM4G=y
# CONFIG_HIGHMEM64G is not set
CONFIG_HIGHMEM=y
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
# CONFIG_SPARSEMEM_STATIC is not set
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_HIGHPTE is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
# CONFIG_EFI is not set
CONFIG_IRQBALANCE=y
CONFIG_SECCOMP=y
# CONFIG_HZ_100 is not set
# CONFIG_HZ_250 is not set
CONFIG_HZ_1000=y
CONFIG_HZ=1000
CONFIG_PHYSICAL_START=0x100000
CONFIG_KEXEC=y
#
# Power management options (ACPI, APM)
#
CONFIG_PM=y
# CONFIG_PM_LEGACY is not set
# CONFIG_PM_DEBUG is not set

#
# ACPI (Advanced Configuration and Power Interface) Support
#
CONFIG_ACPI=y
# CONFIG_ACPI_AC is not set
# CONFIG_ACPI_BATTERY is not set
# CONFIG_ACPI_BUTTON is not set
# CONFIG_ACPI_VIDEO is not set
# CONFIG_ACPI_HOTKEY is not set
CONFIG_ACPI_FAN=m
CONFIG_ACPI_PROCESSOR=m
CONFIG_ACPI_THERMAL=m
# CONFIG_ACPI_ASUS is not set
# CONFIG_ACPI_IBM is not set
# CONFIG_ACPI_TOSHIBA is not set
CONFIG_ACPI_BLACKLIST_YEAR=0
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_SYSTEM=y
CONFIG_X86_PM_TIMER=y
# CONFIG_ACPI_CONTAINER is not set

#
# APM (Advanced Power Management) BIOS Support
#

#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_TABLE=m
# CONFIG_CPU_FREQ_DEBUG is not set
CONFIG_CPU_FREQ_STAT=m
CONFIG_CPU_FREQ_STAT_DETAILS=y
CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=m
CONFIG_CPU_FREQ_GOV_USERSPACE=m
CONFIG_CPU_FREQ_GOV_ONDEMAND=m
CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m

#
# CPUFreq processor drivers
#
CONFIG_X86_ACPI_CPUFREQ=m
# CONFIG_X86_POWERNOW_K6 is not set
# CONFIG_X86_POWERNOW_K7 is not set
# CONFIG_X86_POWERNOW_K8 is not set
# CONFIG_X86_GX_SUSPMOD is not set
# CONFIG_X86_SPEEDSTEP_CENTRINO is not set
# CONFIG_X86_SPEEDSTEP_ICH is not set
# CONFIG_X86_SPEEDSTEP_SMI is not set
CONFIG_X86_P4_CLOCKMOD=m
# CONFIG_X86_CPUFREQ_NFORCE2 is not set
# CONFIG_X86_LONGRUN is not set
# CONFIG_X86_LONGHAUL is not set

#
# shared options
#
# CONFIG_X86_ACPI_CPUFREQ_PROC_INTF is not set
CONFIG_X86_SPEEDSTEP_LIB=m

#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GOMMCONFIG is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
# CONFIG_PCIEPORTBUS is not set
# CONFIG_PCI_MSI is not set
# CONFIG_PCI_LEGACY_PROC is not set
# CONFIG_PCI_DEBUG is not set
CONFIG_ISA_DMA_API=y
# CONFIG_ISA is not set
# CONFIG_MCA is not set
# CONFIG_SCx200 is not set
# CONFIG_HOTPLUG_CPU is not set

#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set

#
# PCI Hotplug Support
#
# CONFIG_HOTPLUG_PCI is not set

#
# Executable file formats
#
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_MISC=m

#
# Networking
#
# CONFIG_NET is not set

#
# Device Drivers
#

#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
# CONFIG_DEBUG_DRIVER is not set

#
# Connector - unified userspace <-> kernelspace linker
#

#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set

#
# Parallel port support
#
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
# CONFIG_PARPORT_SERIAL is not set
# CONFIG_PARPORT_PC_FIFO is not set
# CONFIG_PARPORT_PC_SUPERIO is not set
# CONFIG_PARPORT_GSC is not set
# CONFIG_PARPORT_1284 is not set

#
# Plug and Play support
#
CONFIG_PNP=y
# CONFIG_PNP_DEBUG is not set

#
# Protocols
#
CONFIG_PNPACPI=y

#
# Block devices
#
# CONFIG_BLK_DEV_FD is not set
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=m
CONFIG_BLK_DEV_CRYPTOLOOP=m
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_UB is not set
# CONFIG_BLK_DEV_RAM is not set
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_CDROM_PKTCDVD=m
CONFIG_CDROM_PKTCDVD_BUFFERS=8
CONFIG_CDROM_PKTCDVD_WCACHE=y

#
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y

#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
CONFIG_BLK_DEV_IDECD=m
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
CONFIG_IDE_TASK_IOCTL=y

#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_IDEPNP is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_BLK_DEV_ATIIXP is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_CS5535 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_SC1200 is not set
CONFIG_BLK_DEV_PIIX=y
# CONFIG_BLK_DEV_IT821X is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_IDE_ARM is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set

#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
CONFIG_SCSI_PROC_FS=y

#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
# CONFIG_BLK_DEV_SR is not set
# CONFIG_CHR_DEV_SG is not set
# CONFIG_CHR_DEV_SCH is not set

#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set

#
# SCSI Transport Attributes
#
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_SAS_ATTRS is not set

#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_MEGARAID_SAS is not set
CONFIG_SCSI_SATA=y
# CONFIG_SCSI_SATA_AHCI is not set
# CONFIG_SCSI_SATA_SVW is not set
CONFIG_SCSI_ATA_PIIX=y
# CONFIG_SCSI_SATA_MV is not set
# CONFIG_SCSI_SATA_NV is not set
# CONFIG_SCSI_PDC_ADMA is not set
# CONFIG_SCSI_SATA_QSTOR is not set
# CONFIG_SCSI_SATA_PROMISE is not set
# CONFIG_SCSI_SATA_SX4 is not set
# CONFIG_SCSI_SATA_SIL is not set
# CONFIG_SCSI_SATA_SIL24 is not set
# CONFIG_SCSI_SATA_SIS is not set
# CONFIG_SCSI_SATA_ULI is not set
# CONFIG_SCSI_SATA_VIA is not set
# CONFIG_SCSI_SATA_VITESSE is not set
CONFIG_SCSI_SATA_INTEL_COMBINED=y
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
CONFIG_SCSI_QLA2XXX=y
# CONFIG_SCSI_QLA21XX is not set
# CONFIG_SCSI_QLA22XX is not set
# CONFIG_SCSI_QLA2300 is not set
# CONFIG_SCSI_QLA2322 is not set
# CONFIG_SCSI_QLA6312 is not set
# CONFIG_SCSI_QLA24XX is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set

#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
# CONFIG_FUSION_SPI is not set
# CONFIG_FUSION_FC is not set
# CONFIG_FUSION_SAS is not set

#
# IEEE 1394 (FireWire) support
#
# CONFIG_IEEE1394 is not set

#
# I2O device support
#
# CONFIG_I2O is not set

#
# Network device support
#
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set

#
# ISDN subsystem
#

#
# Telephony Support
#
# CONFIG_PHONE is not set

#
# Input device support
#
CONFIG_INPUT=y

#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=m
# CONFIG_INPUT_EVBUG is not set

#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=m
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set

#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
# CONFIG_SERIO_SERPORT is not set
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PARKBD is not set
# CONFIG_SERIO_PCIPS2 is not set
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
# CONFIG_GAMEPORT is not set

#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_SERIAL_NONSTANDARD is not set

#
# Serial drivers
#
CONFIG_SERIAL_8250=m
# CONFIG_SERIAL_8250_ACPI is not set
CONFIG_SERIAL_8250_NR_UARTS=4
# CONFIG_SERIAL_8250_EXTENDED is not set

#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=m
# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
# CONFIG_LEGACY_PTYS is not set
# CONFIG_PRINTER is not set
# CONFIG_PPDEV is not set
# CONFIG_TIPAR is not set

#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set

#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
CONFIG_HW_RANDOM=m
CONFIG_NVRAM=m
CONFIG_RTC=m
CONFIG_RTC_HISTOGRAM=m
CONFIG_BLOCKER=y
CONFIG_LPPTEST=m
CONFIG_GEN_RTC=m
CONFIG_GEN_RTC_X=y
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_SONYPI is not set

#
# Ftape, the floppy tape device driver
#
CONFIG_AGP=m
# CONFIG_AGP_ALI is not set
# CONFIG_AGP_ATI is not set
# CONFIG_AGP_AMD is not set
# CONFIG_AGP_AMD64 is not set
CONFIG_AGP_INTEL=m
# CONFIG_AGP_NVIDIA is not set
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_SWORKS is not set
# CONFIG_AGP_VIA is not set
# CONFIG_AGP_EFFICEON is not set
# CONFIG_DRM is not set
# CONFIG_MWAVE is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_HPET is not set
# CONFIG_HANGCHECK_TIMER is not set

#
# TPM devices
#
# CONFIG_TCG_TPM is not set
# CONFIG_TELCLOCK is not set

#
# I2C support
#
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=m

#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=y
# CONFIG_I2C_ALGOPCF is not set
# CONFIG_I2C_ALGOPCA is not set

#
# I2C Hardware Bus support
#
# CONFIG_I2C_ALI1535 is not set
# CONFIG_I2C_ALI1563 is not set
# CONFIG_I2C_ALI15X3 is not set
# CONFIG_I2C_AMD756 is not set
# CONFIG_I2C_AMD8111 is not set
CONFIG_I2C_I801=m
CONFIG_I2C_I810=m
# CONFIG_I2C_PIIX4 is not set
CONFIG_I2C_ISA=m
# CONFIG_I2C_NFORCE2 is not set
# CONFIG_I2C_PARPORT is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
# CONFIG_SCx200_ACB is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_STUB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
# CONFIG_I2C_PCA_ISA is not set

#
# Miscellaneous I2C Chip support
#
# CONFIG_SENSORS_DS1337 is not set
# CONFIG_SENSORS_DS1374 is not set
# CONFIG_SENSORS_EEPROM is not set
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_RTC8564 is not set
# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_RTC_X1205_I2C is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set

#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set

#
# Hardware Monitoring support
#
CONFIG_HWMON=m
CONFIG_HWMON_VID=m
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM1026 is not set
# CONFIG_SENSORS_ADM1031 is not set
# CONFIG_SENSORS_ADM9240 is not set
# CONFIG_SENSORS_ASB100 is not set
# CONFIG_SENSORS_ATXP1 is not set
# CONFIG_SENSORS_DS1621 is not set
# CONFIG_SENSORS_FSCHER is not set
# CONFIG_SENSORS_FSCPOS is not set
# CONFIG_SENSORS_GL518SM is not set
# CONFIG_SENSORS_GL520SM is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_LM63 is not set
# CONFIG_SENSORS_LM75 is not set
# CONFIG_SENSORS_LM77 is not set
# CONFIG_SENSORS_LM78 is not set
# CONFIG_SENSORS_LM80 is not set
# CONFIG_SENSORS_LM83 is not set
# CONFIG_SENSORS_LM85 is not set
# CONFIG_SENSORS_LM87 is not set
# CONFIG_SENSORS_LM90 is not set
# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_SIS5595 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
# CONFIG_SENSORS_VIA686A is not set
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83792D is not set
# CONFIG_SENSORS_W83L785TS is not set
CONFIG_SENSORS_W83627HF=m
# CONFIG_SENSORS_W83627EHF is not set
# CONFIG_SENSORS_HDAPS is not set
# CONFIG_HWMON_DEBUG_CHIP is not set

#
# Misc devices
#
# CONFIG_IBM_ASM is not set

#
# Multimedia Capabilities Port drivers
#

#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set

#
# Digital Video Broadcasting Devices
#

#
# Graphics support
#
CONFIG_FB=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_MACMODES is not set
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_ARC is not set
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
# CONFIG_FB_VGA16 is not set
# CONFIG_FB_VESA is not set
CONFIG_VIDEO_SELECT=y
# CONFIG_FB_HGA is not set
# CONFIG_FB_S1D13XXX is not set
CONFIG_FB_NVIDIA=y
CONFIG_FB_NVIDIA_I2C=y
# CONFIG_FB_RIVA is not set
# CONFIG_FB_I810 is not set
# CONFIG_FB_INTEL is not set
# CONFIG_FB_MATROX is not set
# CONFIG_FB_RADEON_OLD is not set
# CONFIG_FB_RADEON is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_SAVAGE is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_CYBLA is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_GEODE is not set
# CONFIG_FB_VIRTUAL is not set

#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y

#
# Logo configuration
#
CONFIG_LOGO=y
# CONFIG_LOGO_LINUX_MONO is not set
# CONFIG_LOGO_LINUX_VGA16 is not set
CONFIG_LOGO_LINUX_CLUT224=y
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set

#
# Sound
#
CONFIG_SOUND=m

#
# Advanced Linux Sound Architecture
#
CONFIG_SND=m
CONFIG_SND_AC97_CODEC=m
CONFIG_SND_AC97_BUS=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
CONFIG_SND_RAWMIDI=m
CONFIG_SND_SEQUENCER=m
CONFIG_SND_SEQ_DUMMY=m
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=m
CONFIG_SND_PCM_OSS=m
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_RTCTIMER=m
CONFIG_SND_SEQ_RTCTIMER_DEFAULT=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set
CONFIG_SND_GENERIC_DRIVER=y

#
# Generic devices
#
CONFIG_SND_DUMMY=m
CONFIG_SND_VIRMIDI=m
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_SERIAL_U16550 is not set
# CONFIG_SND_MPU401 is not set

#
# PCI devices
#
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_ATIIXP is not set
# CONFIG_SND_ATIIXP_MODEM is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_EMU10K1 is not set
# CONFIG_SND_EMU10K1X is not set
# CONFIG_SND_CA0106 is not set
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_MIXART is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_HDSPM is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_YMFPCI is not set
# CONFIG_SND_AD1889 is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_FM801 is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
CONFIG_SND_INTEL8X0=m
# CONFIG_SND_INTEL8X0M is not set
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_VIA82XX is not set
# CONFIG_SND_VIA82XX_MODEM is not set
# CONFIG_SND_VX222 is not set
# CONFIG_SND_HDA_INTEL is not set

#
# USB devices
#
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_USX2Y is not set

#
# Open Sound System
#
# CONFIG_SOUND_PRIME is not set

#
# USB support
#
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB=m
# CONFIG_USB_DEBUG is not set

#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_SUSPEND is not set
# CONFIG_USB_OTG is not set

#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=m
# CONFIG_USB_EHCI_SPLIT_ISO is not set
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_OHCI_HCD is not set
CONFIG_USB_UHCI_HCD=m
# CONFIG_USB_SL811_HCD is not set

#
# USB Device Class drivers
#
# CONFIG_OBSOLETE_OSS_USB_DRIVER is not set
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set

#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#

#
# may also be needed; see USB_STORAGE Help for more information
#
# CONFIG_USB_STORAGE is not set

#
# USB Input Devices
#
# CONFIG_USB_HID is not set

#
# USB HID Boot Protocol drivers
#
# CONFIG_USB_KBD is not set
# CONFIG_USB_MOUSE is not set
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_ACECAD is not set
# CONFIG_USB_KBTAB is not set
# CONFIG_USB_POWERMATE is not set
# CONFIG_USB_MTOUCH is not set
# CONFIG_USB_ITMTOUCH is not set
# CONFIG_USB_EGALAX is not set
# CONFIG_USB_YEALINK is not set
# CONFIG_USB_XPAD is not set
# CONFIG_USB_ATI_REMOTE is not set
# CONFIG_USB_KEYSPAN_REMOTE is not set
# CONFIG_USB_APPLETOUCH is not set

#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set

#
# USB Multimedia devices
#
# CONFIG_USB_DABUSB is not set

#
# Video4Linux support is needed for USB Multimedia device support
#

#
# Networking support is needed for USB Network Adapter support
#
# CONFIG_USB_MON is not set

#
# USB port drivers
#
# CONFIG_USB_USS720 is not set

#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set

#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_PHIDGETKIT is not set
# CONFIG_USB_PHIDGETSERVO is not set
# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TEST is not set

#
# USB DSL modem support
#

#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set

#
# MMC/SD Card support
#
# CONFIG_MMC is not set

#
# InfiniBand support
#
# CONFIG_INFINIBAND is not set

#
# SN Devices
#

#
# File systems
#
CONFIG_EXT2_FS=m
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
CONFIG_EXT2_FS_XIP=y
CONFIG_FS_XIP=y
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
CONFIG_REISERFS_FS=m
# CONFIG_REISERFS_CHECK is not set
CONFIG_REISERFS_PROC_INFO=y
CONFIG_REISERFS_FS_XATTR=y
CONFIG_REISERFS_FS_POSIX_ACL=y
CONFIG_REISERFS_FS_SECURITY=y
CONFIG_JFS_FS=m
CONFIG_JFS_POSIX_ACL=y
CONFIG_JFS_SECURITY=y
# CONFIG_JFS_DEBUG is not set
CONFIG_JFS_STATISTICS=y
CONFIG_FS_POSIX_ACL=y
CONFIG_XFS_FS=m
CONFIG_XFS_QUOTA=y
CONFIG_XFS_SECURITY=y
CONFIG_XFS_POSIX_ACL=y
# CONFIG_XFS_RT is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_INOTIFY=y
CONFIG_QUOTA=y
# CONFIG_QFMT_V1 is not set
CONFIG_QFMT_V2=m
CONFIG_QUOTACTL=y
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
CONFIG_AUTOFS4_FS=m
CONFIG_FUSE_FS=m

#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=m
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_ZISOFS_FS=m
CONFIG_UDF_FS=m
CONFIG_UDF_NLS=y

#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
CONFIG_NTFS_FS=m
# CONFIG_NTFS_DEBUG is not set
CONFIG_NTFS_RW=y

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
# CONFIG_PROC_KCORE is not set
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
CONFIG_RELAYFS_FS=m

#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set

#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y

#
# Native Language Support
#
CONFIG_NLS=m
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=m
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
CONFIG_NLS_CODEPAGE_852=m
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
CONFIG_NLS_CODEPAGE_1250=m
# CONFIG_NLS_CODEPAGE_1251 is not set
# CONFIG_NLS_ASCII is not set
CONFIG_NLS_ISO8859_1=m
CONFIG_NLS_ISO8859_2=m
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
CONFIG_NLS_UTF8=m

#
# Instrumentation Support
#
# CONFIG_PROFILING is not set
CONFIG_PROFILE_NMI=y
# CONFIG_KPROBES is not set

#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
# CONFIG_PRINTK_IGNORE_LOGLEVEL is not set
CONFIG_DEBUG_KERNEL=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_LOG_BUF_SHIFT=20
CONFIG_PARANOID_GENERIC_TIME=y
CONFIG_DETECT_SOFTLOCKUP=y
CONFIG_SCHEDSTATS=y
# CONFIG_DEBUG_SLAB is not set
CONFIG_DEBUG_PREEMPT=y
CONFIG_DEBUG_IRQ_FLAGS=y
CONFIG_WAKEUP_TIMING=y
CONFIG_WAKEUP_LATENCY_HIST=y
CONFIG_PREEMPT_TRACE=y
CONFIG_CRITICAL_PREEMPT_TIMING=y
CONFIG_PREEMPT_OFF_HIST=y
CONFIG_CRITICAL_IRQSOFF_TIMING=y
CONFIG_INTERRUPT_OFF_HIST=y
CONFIG_CRITICAL_TIMING=y
CONFIG_LATENCY_TIMING=y
CONFIG_CRITICAL_LATENCY_HIST=y
CONFIG_LATENCY_HIST=y
CONFIG_LATENCY_TRACE=y
CONFIG_MCOUNT=y
CONFIG_DEBUG_DEADLOCKS=y
CONFIG_DEBUG_RT_LOCKING_MODE=y
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_DEBUG_HIGHMEM=y
CONFIG_DEBUG_BUGVERBOSE=y
CONFIG_DEBUG_INFO=y
CONFIG_DEBUG_FS=y
CONFIG_DEBUG_VM=y
CONFIG_FRAME_POINTER=y
CONFIG_RCU_TORTURE_TEST=m
CONFIG_EARLY_PRINTK=y
CONFIG_DEBUG_STACKOVERFLOW=y
# CONFIG_DEBUG_STACK_USAGE is not set
CONFIG_DEBUG_PAGEALLOC=y
CONFIG_4KSTACKS=y
CONFIG_X86_FIND_SMP_CONFIG=y
CONFIG_X86_MPPARSE=y

#
# Security options
#
CONFIG_KEYS=y
CONFIG_KEYS_DEBUG_PROC_KEYS=y
CONFIG_SECURITY=y
CONFIG_SECURITY_NETWORK=y
CONFIG_SECURITY_CAPABILITIES=y
# CONFIG_SECURITY_ROOTPLUG is not set
CONFIG_SECURITY_SECLVL=y

#
# Cryptographic options
#
CONFIG_CRYPTO=y
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_NULL is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
CONFIG_CRYPTO_SHA1=y
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
# CONFIG_CRYPTO_WP512 is not set
# CONFIG_CRYPTO_TGR192 is not set
# CONFIG_CRYPTO_DES is not set
# CONFIG_CRYPTO_BLOWFISH is not set
# CONFIG_CRYPTO_TWOFISH is not set
# CONFIG_CRYPTO_SERPENT is not set
# CONFIG_CRYPTO_AES_586 is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
# CONFIG_CRYPTO_TEA is not set
# CONFIG_CRYPTO_ARC4 is not set
# CONFIG_CRYPTO_KHAZAD is not set
# CONFIG_CRYPTO_ANUBIS is not set
# CONFIG_CRYPTO_DEFLATE is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_TEST is not set

#
# Hardware crypto devices
#
# CONFIG_CRYPTO_DEV_PADLOCK is not set

#
# Library routines
#
CONFIG_CRC_CCITT=m
CONFIG_CRC16=m
CONFIG_CRC32=y
CONFIG_LIBCRC32C=m
CONFIG_ZLIB_INFLATE=m
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_GENERIC_PENDING_IRQ=y
CONFIG_X86_SMP=y
CONFIG_X86_HT=y
CONFIG_X86_BIOS_REBOOT=y
CONFIG_X86_TRAMPOLINE=y
CONFIG_KTIME_SCALAR=y

[8.] Environment

[8.1.] Software
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.

Linux debian 2.6.15-rc7-rt3 #3 SMP PREEMPT Mon Jan 2 23:46:45 CET 2006
i686 GNU/Linux

Gnu C 4.0.3
Gnu make 3.81beta4
binutils 2.16.91
util-linux 2.12r
mount 2.12r
module-init-tools 3.2.2
e2fsprogs 1.39-WIP
jfsutils 1.1.8
reiserfsprogs 3.6.19
reiser4progs 1.0.5
xfsprogs 2.7.7
Linux C Library 2.3.5
Dynamic linker (ldd) 2.3.5
Procps 3.2.6
Net-tools 1.60
Console-tools 0.2.3
Sh-utils 5.93
udev 079
Modules Loaded binfmt_misc thermal fan processor microcode
ehci_hcd uhci_hcd usbcore w83627hf hwmon_vid hwmon i2c_isa i2c_i801
psmouse ide_cd cdrom rtc

[8.2.] Processor information
processor : 0
vendor_id : GenuineIntel
cpu family : 15
model : 2
model name : Intel(R) Pentium(R) 4 CPU 2.80GHz
stepping : 5
cpu MHz : 2798.743
cache size : 512 KB
physical id : 0
siblings : 2
core id : 0
cpu cores : 1
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat
pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe cid xtpr
bogomips : 5601.32

processor : 1
vendor_id : GenuineIntel
cpu family : 15
model : 2
model name : Intel(R) Pentium(R) 4 CPU 2.80GHz
stepping : 5
cpu MHz : 2798.743
cache size : 512 KB
physical id : 0
siblings : 2
core id : 0
cpu cores : 1
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat
pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe cid xtpr
bogomips : 5596.72


[8.3.] Module information
binfmt_misc 12552 1 - Live 0xf98a8000
thermal 14472 0 - Live 0xf98a3000
fan 5380 0 - Live 0xf8879000
processor 26316 1 thermal, Live 0xf98f1000
microcode 7760 0 - Live 0xf8876000
ehci_hcd 30088 0 - Live 0xf886b000
uhci_hcd 32400 0 - Live 0xf883a000
usbcore 120708 3 ehci_hcd,uhci_hcd, Live 0xf884c000
w83627hf 23952 0 - Live 0xf8833000
hwmon_vid 3072 1 w83627hf, Live 0xf8845000
hwmon 3716 1 w83627hf, Live 0xf882c000
i2c_isa 6400 1 w83627hf, Live 0xf8849000
i2c_i801 9740 0 - Live 0xf8804000
psmouse 34436 0 - Live 0xf8822000
ide_cd 38148 0 - Live 0xf8817000
cdrom 34464 1 ide_cd, Live 0xf880d000
rtc 14132 0 - Live 0xf882e000

[8.4.] Loaded driver and hardware information
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0290-0297 : pnp 00:09
0295-0296 : w83627hf
0376-0376 : ide1
03c0-03df : vga+
03f6-03f6 : ide0
0400-041f : 0000:00:1f.3
0400-040f : i801_smbus
0480-04bf : 0000:00:1f.0
0680-06ff : pnp 00:09
0800-087f : 0000:00:1f.0
0800-0803 : PM1a_EVT_BLK
0804-0805 : PM1a_CNT_BLK
0808-080b : PM_TMR
0828-082f : GPE0_BLK
0cf8-0cff : PCI conf1
c400-c40f : 0000:00:1f.2
c400-c40f : libata
c480-c483 : 0000:00:1f.2
c480-c483 : libata
c800-c807 : 0000:00:1f.2
c800-c807 : libata
c880-c883 : 0000:00:1f.2
c880-c883 : libata
cc00-cc07 : 0000:00:1f.2
cc00-cc07 : libata
d000-d0ff : 0000:00:1f.5
d400-d43f : 0000:00:1f.5
d480-d49f : 0000:00:1d.0
d480-d49f : uhci_hcd
d800-d81f : 0000:00:1d.1
d800-d81f : uhci_hcd
d880-d89f : 0000:00:1d.2
d880-d89f : uhci_hcd
dc00-dc1f : 0000:00:1d.3
dc00-dc1f : uhci_hcd
e000-efff : PCI Bus #02
e800-e8ff : 0000:02:05.0
fc00-fc0f : 0000:00:1f.1
fc00-fc07 : ide0
fc08-fc0f : ide1
00000000-0009fbff : System RAM
00000000-00000000 : Crash kernel
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000cf3ff : Video ROM
000f0000-000fffff : System ROM
00100000-3ff2ffff : System RAM
00100000-0024cbe2 : Kernel code
0024cbe3-003dbb2f : Kernel data
3ff30000-3ff3ffff : ACPI Tables
3ff40000-3ffeffff : ACPI Non-volatile Storage
3fff0000-3fffffff : reserved
50000000-500003ff : 0000:00:1f.1
e8000000-f4ffffff : PCI Bus #01
e8000000-efffffff : 0000:01:00.0
e8000000-efffffff : nvidiafb
f5fff400-f5fff4ff : 0000:00:1f.5
f5fff800-f5fff9ff : 0000:00:1f.5
f5fffc00-f5ffffff : 0000:00:1d.7
f5fffc00-f5ffffff : ehci_hcd
f6000000-f7efffff : PCI Bus #01
f6000000-f6ffffff : 0000:01:00.0
f6000000-f6ffffff : nvidiafb
f7ee0000-f7efffff : 0000:01:00.0
f7f00000-fbffffff : PCI Bus #02
f7ffc000-f7ffffff : 0000:02:05.0
ffb80000-ffffffff : reserved
[8.5.] PCI information
0000:00:00.0 Host bridge: Intel Corporation 82865G/PE/P DRAM
Controller/Host-Hub Interface (rev 02)
Subsystem: ASUSTeK Computer Inc. P4P800 Mainboard
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at <ignored> (32-bit, prefetchable)
Capabilities: [e4] #09 [2106]
Capabilities: [a0] AGP version 3.0
Status: RQ=32 Iso- ArqSz=2 Cal=2 SBA+ ITACoh- GART64- HTrans- 64bit-
FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=2 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
0000:00:01.0 PCI bridge: Intel Corporation 82865G/PE/P PCI to AGP
Controller (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: f6000000-f7efffff
Prefetchable memory behind bridge: e8000000-f4ffffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
0000:00:1d.0 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R)
USB UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P4P800 Mainboard
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at d480 [size=32]
0000:00:1d.1 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R)
USB UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P4P800 Mainboard
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 18
Region 4: I/O ports at d800 [size=32]
0000:00:1d.2 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R)
USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P4P800 Mainboard
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 17
Region 4: I/O ports at d880 [size=32]
0000:00:1d.3 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R)
USB UHCI Controller #4 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P4P800 Mainboard
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at dc00 [size=32]
0000:00:1d.7 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R)
USB2 EHCI Controller (rev 02) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. P4P800 Mainboard
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 0: Memory at f5fffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] #0a [20a0]
0000:00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c2)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: f7f00000-fbffffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
0000:00:1f.0 ISA bridge: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC
Interface Bridge (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:00:1f.1 IDE interface: Intel Corporation 82801EB/ER (ICH5/ICH5R)
IDE Controller (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. P4P800 Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at fc00 [size=16]
Region 5: Memory at 50000000 (32-bit, non-prefetchable) [size=1K]
0000:00:1f.2 IDE interface: Intel Corporation 82801EB (ICH5) SATA
Controller (rev 02) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: ASUSTeK Computer Inc.: Unknown device 80a6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at cc00 [size=8]
Region 1: I/O ports at c880 [size=4]
Region 2: I/O ports at c800 [size=8]
Region 3: I/O ports at c480 [size=4]
Region 4: I/O ports at c400 [size=16]
0000:00:1f.3 SMBus: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus
Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. P4P800 Mainboard
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 5
Region 4: I/O ports at 0400 [size=32]
0000:00:1f.5 Multimedia audio controller: Intel Corporation 82801EB/ER
(ICH5/ICH5R) AC'97 Audio Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. P4P800 Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 5
Region 0: I/O ports at d000 [size=256]
Region 1: I/O ports at d400 [size=64]
Region 2: Memory at f5fff800 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at f5fff400 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:01:00.0 VGA compatible controller: nVidia Corporation NV34
[GeForce FX 5200] (rev a1) (prog-if 00 [VGA])
Subsystem: PROLINK Microsystems Corp: Unknown device 1152
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f6000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at f7ee0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 3.0
Status: RQ=32 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64- HTrans- 64bit-
FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
0000:02:05.0 Ethernet controller: 3Com Corporation 3c940
10/100/1000Base-T [Marvell] (rev 12)
Subsystem: ASUSTeK Computer Inc. P4P800/K8V Deluxe motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 0x04 (16 bytes)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at f7ffc000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at e800 [size=256]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=7 DScale=1 PME-
Capabilities: [50] Vital Product Data

[8.6.] SCSI information
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: ATA Model: Maxtor 6Y200M0 Rev: YAR5
Type: Direct-Access ANSI SCSI revision: 05


OOPS Reporting Tool v.ltg1
www.wsi.edu.pl/~piotrowskim/files/ort/ltg/

Regards,
Michal Piotrowski
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2006-01-03 00:13    [from the cache]
©2003-2014 Jasper Spaans. Advertise on this site