lkml.org 
[lkml]   [2005]   [Sep]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    Patch in this message
    /
    Subject2.6.13.1 locks machine after some time, 2.6.12.5 work fine
    From
    Date
    Hi,

    I had reported the same problem some time back for 2.6.13 and now tried
    2.6.13.1, but the problem persists. After some time (about 1 hour or
    so) the machine just locks hard - screen, keyboard, network. I noticed
    that the hard disk light is on permanently in that stage. It always
    locks up during disk operation (this time which installing some new
    Debian packages). The (currently one and only) disk is hanging off the
    0000:00:07.1 VIA IDE controller, the built-in RAID controller is unused.

    2.6.12.5 was running stable for a very long time (upgraded when it came
    out and never rebooted until 2.6.13 was released). I'm now back to
    2.6.12.5 and the machine works fine again, so I doubt it's a hardware
    failure.

    There is nothing in syslog, and I can't switch to console or do
    Alt-SysRq, so I'm at loss how to investigate this further.

    Best,
    Norbert


    I append the lspci -vvv from both 2.6.12.5 and 2.6.13.1 The diff
    between these two is:

    --- 2.6.12.5/lspci 2005-09-12 14:17:56.000000000 -0700
    +++ 2.6.13.1/lspci 2005-09-12 14:12:17.000000000 -0700
    @@ -89,6 +89,7 @@
    Interrupt: pin A routed to IRQ 10
    Region 0: I/O ports at b000 [size=128]
    Region 1: Memory at e7000000 (32-bit, non-prefetchable)
    [size=128]
    + Expansion ROM at 40080000 [disabled] [size=128K]
    Capabilities: [dc] Power Management version 1
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1
    +,D2+,D3hot+,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    @@ -115,6 +116,7 @@
    Region 2: I/O ports at c000 [size=8]
    Region 3: I/O ports at c400 [size=4]
    Region 4: I/O ports at c800 [size=16]
    + Expansion ROM at 40000000 [disabled] [size=512K]
    Capabilities: [60] Power Management version 2
    Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=3 PME-
    @@ -128,6 +130,7 @@
    Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
    Region 1: I/O ports at 9000 [size=256]
    Region 2: Memory at e5000000 (32-bit, non-prefetchable)
    [size=64K]
    + Expansion ROM at e4000000 [disabled] [size=128K]
    Capabilities: [58] AGP version 2.0
    Status: RQ=80 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
    HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
    Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW-
    Rate=<none>

    ===============
    lspci -vvv from 2.6.12.5:
    ===============
    0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365
    [KT133/KM133] (rev 02)
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort+ >SERR- <PERR-
    Latency: 0
    Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
    Capabilities: [a0] AGP version 2.0
    Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit-
    FW- AGP3- Rate=x1,x2,x4
    Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
    Capabilities: [c0] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133
    AGP] (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort+ >SERR- <PERR-
    Latency: 0
    Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
    I/O behind bridge: 00009000-00009fff
    Memory behind bridge: e4000000-e5ffffff
    Prefetchable memory behind bridge: d0000000-dfffffff
    BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
    Capabilities: [80] Power Management version 2
    Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super
    South] (rev 22)
    Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping+ SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    0000:00:07.1 IDE interface: VIA Technologies, Inc.
    VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 10)
    (prog-if 8a [Master SecP PriP])
    Subsystem: VIA Technologies, Inc.
    VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32
    Region 4: I/O ports at a000 [size=16]
    Capabilities: [c0] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    0000:00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
    1.1 Controller (rev 10) (prog-if 00 [UHCI])
    Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32, Cache Line Size: 0x08 (32 bytes)
    Interrupt: pin D routed to IRQ 12
    Region 4: I/O ports at a400 [size=32]
    Capabilities: [80] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    0000:00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
    1.1 Controller (rev 10) (prog-if 00 [UHCI])
    Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32, Cache Line Size: 0x08 (32 bytes)
    Interrupt: pin D routed to IRQ 12
    Region 4: I/O ports at a800 [size=32]
    Capabilities: [80] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    0000:00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
    (rev 30)
    Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Interrupt: pin ? routed to IRQ 9
    Capabilities: [68] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    0000:00:0a.0 Ethernet controller: Accton Technology Corporation
    SMC2-1211TX (rev 10)
    Subsystem: Accton Technology Corporation EN-1207D Fast Ethernet Adapter
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32 (8000ns min, 16000ns max)
    Interrupt: pin A routed to IRQ 11
    Region 0: I/O ports at ac00 [size=256]
    Region 1: Memory at e7001000 (32-bit, non-prefetchable) [size=256]
    Capabilities: [50] Power Management version 1
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot
    +,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    0000:00:0b.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX
    [Cyclone] (rev 30)
    Subsystem: 3Com Corporation 3C905B Fast Etherlink XL 10/100
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 0x08 (32 bytes)
    Interrupt: pin A routed to IRQ 10
    Region 0: I/O ports at b000 [size=128]
    Region 1: Memory at e7000000 (32-bit, non-prefetchable) [size=128]
    Capabilities: [dc] Power Management version 1
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot
    +,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    0000:00:0f.0 Multimedia audio controller: C-Media Electronics Inc CM8738
    (rev 10)
    Subsystem: C-Media Electronics Inc CMI8738/C3DX PCI Audio Device
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32 (500ns min, 6000ns max)
    Interrupt: pin A routed to IRQ 10
    Region 0: I/O ports at b400 [size=256]
    Capabilities: [c0] Power Management version 2
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    0000:00:10.0 RAID bus controller: Silicon Image, Inc. SiI 0649 Ultra
    ATA/100 PCI to ATA Host Controller (rev 01)
    Subsystem: Silicon Image, Inc. SiI 0649 Ultra ATA/100 PCI to ATA Host
    Controller
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 64 (500ns min, 1000ns max)
    Interrupt: pin A routed to IRQ 12
    Region 0: I/O ports at b800 [size=8]
    Region 1: I/O ports at bc00 [size=4]
    Region 2: I/O ports at c000 [size=8]
    Region 3: I/O ports at c400 [size=4]
    Region 4: I/O ports at c800 [size=16]
    Capabilities: [60] Power Management version 2
    Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=3 PME-
    0000:01:00.0 VGA compatible controller: ATI Technologies Inc RV280
    [Radeon 9200 PRO] (rev 01) (prog-if 00 [VGA])
    Subsystem: Hightech Information System Ltd.: Unknown device 5960
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32 (2000ns min), Cache Line Size: 0x08 (32 bytes)
    Interrupt: pin A routed to IRQ 5
    Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
    Region 1: I/O ports at 9000 [size=256]
    Region 2: Memory at e5000000 (32-bit, non-prefetchable) [size=64K]
    Capabilities: [58] AGP version 2.0
    Status: RQ=80 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit-
    FW+ AGP3- Rate=x1,x2,x4
    Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
    Capabilities: [50] Power Management version 2
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    0000:01:00.1 Display controller: ATI Technologies Inc: Unknown device
    5940 (rev 01)
    Subsystem: Hightech Information System Ltd.: Unknown device 5961
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32 (2000ns min), Cache Line Size: 0x08 (32 bytes)
    Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
    Region 1: Memory at e5010000 (32-bit, non-prefetchable) [size=64K]
    Capabilities: [50] Power Management version 2
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-



    ======================
    lspci -vvv from 2.6.13.1:
    ======================
    0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365
    [KT133/KM133] (rev 02)
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort+ >SERR- <PERR-
    Latency: 0
    Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
    Capabilities: [a0] AGP version 2.0
    Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit-
    FW- AGP3- Rate=x1,x2,x4
    Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
    Capabilities: [c0] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133
    AGP] (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort+ >SERR- <PERR-
    Latency: 0
    Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
    I/O behind bridge: 00009000-00009fff
    Memory behind bridge: e4000000-e5ffffff
    Prefetchable memory behind bridge: d0000000-dfffffff
    BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
    Capabilities: [80] Power Management version 2
    Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super
    South] (rev 22)
    Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping+ SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    0000:00:07.1 IDE interface: VIA Technologies, Inc.
    VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 10)
    (prog-if 8a [Master SecP PriP])
    Subsystem: VIA Technologies, Inc.
    VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32
    Region 4: I/O ports at a000 [size=16]
    Capabilities: [c0] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    0000:00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
    1.1 Controller (rev 10) (prog-if 00 [UHCI])
    Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32, Cache Line Size: 0x08 (32 bytes)
    Interrupt: pin D routed to IRQ 12
    Region 4: I/O ports at a400 [size=32]
    Capabilities: [80] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    0000:00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
    1.1 Controller (rev 10) (prog-if 00 [UHCI])
    Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32, Cache Line Size: 0x08 (32 bytes)
    Interrupt: pin D routed to IRQ 12
    Region 4: I/O ports at a800 [size=32]
    Capabilities: [80] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    0000:00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
    (rev 30)
    Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Interrupt: pin ? routed to IRQ 9
    Capabilities: [68] Power Management version 2
    Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    0000:00:0a.0 Ethernet controller: Accton Technology Corporation
    SMC2-1211TX (rev 10)
    Subsystem: Accton Technology Corporation EN-1207D Fast Ethernet Adapter
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32 (8000ns min, 16000ns max)
    Interrupt: pin A routed to IRQ 11
    Region 0: I/O ports at ac00 [size=256]
    Region 1: Memory at e7001000 (32-bit, non-prefetchable) [size=256]
    Capabilities: [50] Power Management version 1
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot
    +,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    0000:00:0b.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX
    [Cyclone] (rev 30)
    Subsystem: 3Com Corporation 3C905B Fast Etherlink XL 10/100
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 0x08 (32 bytes)
    Interrupt: pin A routed to IRQ 10
    Region 0: I/O ports at b000 [size=128]
    Region 1: Memory at e7000000 (32-bit, non-prefetchable) [size=128]
    Expansion ROM at 40080000 [disabled] [size=128K]
    Capabilities: [dc] Power Management version 1
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot
    +,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    0000:00:0f.0 Multimedia audio controller: C-Media Electronics Inc CM8738
    (rev 10)
    Subsystem: C-Media Electronics Inc CMI8738/C3DX PCI Audio Device
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32 (500ns min, 6000ns max)
    Interrupt: pin A routed to IRQ 10
    Region 0: I/O ports at b400 [size=256]
    Capabilities: [c0] Power Management version 2
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    0000:00:10.0 RAID bus controller: Silicon Image, Inc. SiI 0649 Ultra
    ATA/100 PCI to ATA Host Controller (rev 01)
    Subsystem: Silicon Image, Inc. SiI 0649 Ultra ATA/100 PCI to ATA Host
    Controller
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 64 (500ns min, 1000ns max)
    Interrupt: pin A routed to IRQ 12
    Region 0: I/O ports at b800 [size=8]
    Region 1: I/O ports at bc00 [size=4]
    Region 2: I/O ports at c000 [size=8]
    Region 3: I/O ports at c400 [size=4]
    Region 4: I/O ports at c800 [size=16]
    Expansion ROM at 40000000 [disabled] [size=512K]
    Capabilities: [60] Power Management version 2
    Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=3 PME-
    0000:01:00.0 VGA compatible controller: ATI Technologies Inc RV280
    [Radeon 9200 PRO] (rev 01) (prog-if 00 [VGA])
    Subsystem: Hightech Information System Ltd.: Unknown device 5960
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32 (2000ns min), Cache Line Size: 0x08 (32 bytes)
    Interrupt: pin A routed to IRQ 5
    Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
    Region 1: I/O ports at 9000 [size=256]
    Region 2: Memory at e5000000 (32-bit, non-prefetchable) [size=64K]
    Expansion ROM at e4000000 [disabled] [size=128K]
    Capabilities: [58] AGP version 2.0
    Status: RQ=80 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit-
    FW+ AGP3- Rate=x1,x2,x4
    Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
    Capabilities: [50] Power Management version 2
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    0000:01:00.1 Display controller: ATI Technologies Inc: Unknown device
    5940 (rev 01)
    Subsystem: Hightech Information System Ltd.: Unknown device 5961
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
    Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
    <TAbort- <MAbort- >SERR- <PERR-
    Latency: 32 (2000ns min), Cache Line Size: 0x08 (32 bytes)
    Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
    Region 1: Memory at e5010000 (32-bit, non-prefetchable) [size=64K]
    Capabilities: [50] Power Management version 2
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
    PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-


    [unhandled content-type:application/pgp-signature]
    \
     
     \ /
      Last update: 2005-09-13 02:02    [W:0.068 / U:15.164 seconds]
    ©2003-2017 Jasper Spaans. hosted at Digital OceanAdvertise on this site