Messages in this thread | | | Date | Mon, 20 Jun 2005 23:58:28 +0200 | From | Mathieu Bérard <> | Subject | 2.6.12-mm1 irq 21: nobody cared with snd_via82xx |
| |
Hi, I get this while booting linux 2.6.12-mm1 (+ bridge conntrack fix BTW) with a VIA integrated audio ship.
It worked well at least under 2.6.11-mm1.
(Please cc. me)
Thanks!
Jun 20 23:30:15 perenold kernel: via82xx: Assuming DXS channels with 48k fixed sample rate. Jun 20 23:30:15 perenold kernel: Please try dxs_support=1 or dxs_support=4 option Jun 20 23:30:15 perenold kernel: and report if it works on your machine. Jun 20 23:30:15 perenold kernel: ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 12 (level, low) -> IRQ 21 Jun 20 23:30:15 perenold kernel: PCI: Via IRQ fixup for 0000:00:11.5, from 12 to 5 Jun 20 23:30:15 perenold kernel: PCI: Setting latency timer of device 0000:00:11.5 to 64 Jun 20 23:30:15 perenold kernel: unable to register OSS PCM device 0:0 Jun 20 23:30:15 perenold kernel: irq 21: nobody cared (try booting with the "irqpoll" option. Jun 20 23:30:15 perenold kernel: [<c01329b4>] __report_bad_irq+0x24/0x80 Jun 20 23:30:15 perenold kernel: [<c0132acb>] note_interrupt+0x8b/0xe0 Jun 20 23:30:15 perenold kernel: [<c0132500>] __do_IRQ+0xe0/0xf0 Jun 20 23:30:15 perenold kernel: [<c0104efe>] do_IRQ+0x3e/0x60 Jun 20 23:30:15 perenold kernel: ======================= Jun 20 23:30:15 perenold kernel: [<c01034d6>] common_interrupt+0x1a/0x20 Jun 20 23:30:15 perenold kernel: handlers: Jun 20 23:30:15 perenold kernel: [<e0c4f420>] (snd_via82xx_interrupt+0x0/0xd0 [snd_via82xx]) Jun 20 23:30:15 perenold kernel: Disabling IRQ #21 Jun 20 23:30:15 perenold kernel: unable to register OSS mixer device 0:0
There might be other IRQ-related mess here as I also found this later in the log:
Jun 20 23:30:40 perenold kernel: uhci_hcd 0000:00:11.3: Unlink after no-IRQ? Controller is probably using the wrong IRQ.
lspci -vvv: 0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333] Subsystem: VIA Technologies, Inc.: Unknown device 0000 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+ Latency: 0 Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M] Capabilities: [a0] AGP version 2.0 Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit- FW- Rate=x2 Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333 AGP] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: dde00000-dfefffff Prefetchable memory behind bridge: d9c00000-ddcfffff BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:05.0 Multimedia controller: Philips Semiconductors SAA7134 (rev 01) Subsystem: Pinnacle Systems Inc.: Unknown device 002b Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+ Latency: 64 (62000ns min, 62000ns max) Interrupt: pin A routed to IRQ 17 Region 0: Memory at dfffbc00 (32-bit, non-prefetchable) [size=1K] Capabilities: [40] Power Management version 1 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=1 PME-
0000:00:06.0 Unknown mass storage controller: Promise Technology, Inc. PDC20268 (Ultra100 TX2) (rev 02) (prog-if 85) Subsystem: Promise Technology, Inc. Ultra100TX2 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (1000ns min, 4500ns max), Cache Line Size: 0x08 (32 bytes) Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at ec00 [size=8] Region 1: I/O ports at e800 [size=4] Region 2: I/O ports at e400 [size=8] Region 3: I/O ports at e000 [size=4] Region 4: I/O ports at dc00 [size=16] Region 5: Memory at dfffc000 (32-bit, non-prefetchable) [size=16K] Expansion ROM at 20000000 [disabled] [size=16K] Capabilities: [60] Power Management version 1 Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Edimax Computer Co.: Unknown device 9503 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (8000ns min, 16000ns max) Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at d800 [size=256] Region 1: Memory at dfffbb00 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:08.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Edimax Computer Co.: Unknown device 9503 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (8000ns min, 16000ns max) Interrupt: pin A routed to IRQ 19 Region 0: I/O ports at d400 [size=256] Region 1: Memory at dfffba00 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8233 PCI to ISA Bridge Subsystem: VIA Technologies, Inc.: Unknown device 0000 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: VIA Technologies, Inc. VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Region 4: I/O ports at fc00 [size=16] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1b) (prog-if 00 [UHCI]) Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64, Cache Line Size: 0x08 (32 bytes) Interrupt: pin D routed to IRQ 20 Region 4: I/O ports at c400 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1b) (prog-if 00 [UHCI]) Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64, Cache Line Size: 0x08 (32 bytes) Interrupt: pin D routed to IRQ 20 Region 4: I/O ports at c800 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.4 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1b) (prog-if 00 [UHCI]) Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64, Cache Line Size: 0x08 (32 bytes) Interrupt: pin D routed to IRQ 20 Region 4: I/O ports at cc00 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 10) Subsystem: Avance Logic Inc.: Unknown device 4710 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin C routed to IRQ 21 Region 0: I/O ports at d000 [size=256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:01:00.0 VGA compatible controller: nVidia Corporation NV5 [RIVA TNT2/TNT2 Pro] (rev 11) (prog-if 00 [VGA]) Subsystem: Diamond Multimedia Systems RIVA TNT2/TNT2 Pro Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 248 (1250ns min, 250ns max) Interrupt: pin A routed to IRQ 17 Region 0: Memory at de000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at da000000 (32-bit, prefetchable) [size=32M] Expansion ROM at d9c00000 [disabled] [size=64K] Capabilities: [60] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [44] AGP version 2.0 Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2 Command: RQ=32 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit- FW- Rate=x2
cat /proc/interrupt: CPU0 0: 229435 IO-APIC-edge timer 1: 10 IO-APIC-edge i8042 7: 2 IO-APIC-edge parport0 8: 1 IO-APIC-edge rtc 9: 0 IO-APIC-level acpi 14: 32915 IO-APIC-edge ide0 15: 15373 IO-APIC-edge ide1 16: 3311 IO-APIC-level ide3 17: 43800 IO-APIC-level saa7134[0], nvidia 18: 10900 IO-APIC-level eth0 19: 10450 IO-APIC-level eth1 20: 0 IO-APIC-level uhci_hcd:usb1, uhci_hcd:usb2, uhci_hcd:usb3 21: 153721182 IO-APIC-level VIA8233 NMI: 0 LOC: 229376 ERR: 0 MIS: 0
.config: # # Automatically generated make config: don't edit # Linux kernel version: 2.6.12-mm1 # Mon Jun 20 23:07:55 2005 # CONFIG_X86=y CONFIG_MMU=y CONFIG_UID16=y CONFIG_GENERIC_ISA_DMA=y CONFIG_GENERIC_IOMAP=y
# # Code maturity level options # CONFIG_EXPERIMENTAL=y CONFIG_CLEAN_COMPILE=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32
# # General setup # CONFIG_LOCALVERSION="" CONFIG_SWAP=y CONFIG_SYSVIPC=y CONFIG_POSIX_MQUEUE=y CONFIG_BSD_PROCESS_ACCT=y # CONFIG_BSD_PROCESS_ACCT_V3 is not set CONFIG_SYSCTL=y # CONFIG_AUDIT is not set CONFIG_HOTPLUG=y CONFIG_KOBJECT_UEVENT=y CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y # CONFIG_EMBEDDED is not set CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set CONFIG_PRINTK=y CONFIG_BUG=y CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y CONFIG_CC_ALIGN_FUNCTIONS=0 CONFIG_CC_ALIGN_LABELS=0 CONFIG_CC_ALIGN_LOOPS=0 CONFIG_CC_ALIGN_JUMPS=0 # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0
# # Loadable module support # CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y CONFIG_MODULE_FORCE_UNLOAD=y CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y CONFIG_KMOD=y
# # Processor type and features # CONFIG_X86_PC=y # CONFIG_X86_ELAN is not set # CONFIG_X86_VOYAGER is not set # CONFIG_X86_NUMAQ is not set # CONFIG_X86_SUMMIT is not set # CONFIG_X86_BIGSMP is not set # CONFIG_X86_VISWS is not set # CONFIG_X86_GENERICARCH is not set # CONFIG_X86_ES7000 is not set # CONFIG_M386 is not set # CONFIG_M486 is not set # CONFIG_M586 is not set # CONFIG_M586TSC is not set # CONFIG_M586MMX is not set # CONFIG_M686 is not set # CONFIG_MPENTIUMII is not set # CONFIG_MPENTIUMIII is not set # CONFIG_MPENTIUMM is not set # CONFIG_MPENTIUM4 is not set # CONFIG_MK6 is not set CONFIG_MK7=y # CONFIG_MK8 is not set # CONFIG_MCRUSOE is not set # CONFIG_MEFFICEON is not set # CONFIG_MWINCHIPC6 is not set # CONFIG_MWINCHIP2 is not set # CONFIG_MWINCHIP3D is not set # CONFIG_MGEODEGX1 is not set # CONFIG_MCYRIXIII is not set # CONFIG_MVIAC3_2 is not set # CONFIG_X86_GENERIC is not set CONFIG_X86_CMPXCHG=y CONFIG_X86_XADD=y CONFIG_X86_L1_CACHE_SHIFT=6 CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_X86_WP_WORKS_OK=y CONFIG_X86_INVLPG=y CONFIG_X86_BSWAP=y CONFIG_X86_POPAD_OK=y CONFIG_X86_GOOD_APIC=y CONFIG_X86_INTEL_USERCOPY=y CONFIG_X86_USE_PPRO_CHECKSUM=y CONFIG_X86_USE_3DNOW=y # CONFIG_HPET_TIMER is not set # CONFIG_SMP is not set # CONFIG_PREEMPT_NONE is not set CONFIG_PREEMPT_VOLUNTARY=y # CONFIG_PREEMPT is not set CONFIG_X86_UP_APIC=y CONFIG_X86_UP_IOAPIC=y CONFIG_X86_LOCAL_APIC=y CONFIG_X86_IO_APIC=y CONFIG_X86_TSC=y CONFIG_X86_MCE=y CONFIG_X86_MCE_NONFATAL=y # CONFIG_X86_MCE_P4THERMAL is not set # CONFIG_TOSHIBA is not set # CONFIG_I8K is not set # CONFIG_X86_REBOOTFIXUPS is not set # CONFIG_MICROCODE is not set CONFIG_X86_MSR=m CONFIG_X86_CPUID=m
# # Firmware Drivers # # CONFIG_EDD is not set CONFIG_NOHIGHMEM=y # CONFIG_HIGHMEM4G is not set # CONFIG_HIGHMEM64G is not set CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y # CONFIG_DISCONTIGMEM_MANUAL is not set # CONFIG_SPARSEMEM_MANUAL is not set CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_MATH_EMULATION is not set CONFIG_MTRR=y # CONFIG_EFI is not set CONFIG_REGPARM=y CONFIG_SECCOMP=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_1000 is not set CONFIG_HZ=250
# # Performance-monitoring counters support # # CONFIG_PERFCTR is not set CONFIG_PHYSICAL_START=0x100000 # CONFIG_KEXEC is not set
# # Power management options (ACPI, APM) # CONFIG_PM=y # CONFIG_PM_DEBUG is not set # CONFIG_SOFTWARE_SUSPEND is not set
# # ACPI (Advanced Configuration and Power Interface) Support # CONFIG_ACPI=y CONFIG_ACPI_BOOT=y CONFIG_ACPI_INTERPRETER=y # CONFIG_ACPI_SLEEP is not set # CONFIG_ACPI_AC is not set # CONFIG_ACPI_BATTERY is not set CONFIG_ACPI_BUTTON=m # CONFIG_ACPI_VIDEO is not set # CONFIG_ACPI_FAN is not set CONFIG_ACPI_PROCESSOR=m # CONFIG_ACPI_THERMAL is not set # CONFIG_ACPI_ASUS is not set # CONFIG_ACPI_IBM is not set # CONFIG_ACPI_TOSHIBA is not set # CONFIG_ACPI_CUSTOM_DSDT is not set CONFIG_ACPI_BLACKLIST_YEAR=0 # CONFIG_ACPI_DEBUG is not set CONFIG_ACPI_BUS=y CONFIG_ACPI_EC=y CONFIG_ACPI_POWER=y CONFIG_ACPI_PCI=y CONFIG_ACPI_SYSTEM=y # CONFIG_X86_PM_TIMER is not set # CONFIG_ACPI_CONTAINER is not set
# # APM (Advanced Power Management) BIOS Support # # CONFIG_APM is not set
# # CPU Frequency scaling # # CONFIG_CPU_FREQ is not set
# # Bus options (PCI, PCMCIA, EISA, MCA, ISA) # CONFIG_PCI=y # CONFIG_PCI_GOBIOS is not set # CONFIG_PCI_GOMMCONFIG is not set # CONFIG_PCI_GODIRECT is not set CONFIG_PCI_GOANY=y CONFIG_PCI_BIOS=y CONFIG_PCI_DIRECT=y CONFIG_PCI_MMCONFIG=y # CONFIG_PCIEPORTBUS is not set # CONFIG_PCI_MSI is not set # CONFIG_PCI_LEGACY_PROC is not set CONFIG_PCI_NAMES=y # CONFIG_PCI_DEBUG is not set CONFIG_ISA_DMA_API=y # CONFIG_ISA is not set # CONFIG_MCA is not set # CONFIG_SCx200 is not set
# # PCCARD (PCMCIA/CardBus) support # # CONFIG_PCCARD is not set
# # PCI Hotplug Support # # CONFIG_HOTPLUG_PCI is not set
# # Executable file formats # CONFIG_BINFMT_ELF=y CONFIG_BINFMT_AOUT=m CONFIG_BINFMT_MISC=m
# # Device Drivers #
# # Generic Driver Options # # CONFIG_STANDALONE is not set CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set # CONFIG_DEBUG_DRIVER is not set
# # Connector - unified userspace <-> kernelspace linker # CONFIG_CONNECTOR=y CONFIG_FORK_CONNECTOR=y
# # Memory Technology Devices (MTD) # # CONFIG_MTD is not set
# # Parallel port support # CONFIG_PARPORT=m CONFIG_PARPORT_PC=m # CONFIG_PARPORT_SERIAL is not set CONFIG_PARPORT_PC_FIFO=y CONFIG_PARPORT_PC_SUPERIO=y # CONFIG_PARPORT_GSC is not set CONFIG_PARPORT_1284=y
# # Plug and Play support # CONFIG_PNP=y # CONFIG_PNP_DEBUG is not set
# # Protocols # CONFIG_PNPACPI=y
# # Block devices # CONFIG_BLK_DEV_FD=m # CONFIG_PARIDE is not set # CONFIG_BLK_CPQ_DA is not set # CONFIG_BLK_CPQ_CISS_DA is not set # CONFIG_BLK_DEV_DAC960 is not set # CONFIG_BLK_DEV_UMEM is not set # CONFIG_BLK_DEV_COW_COMMON is not set CONFIG_BLK_DEV_LOOP=m # CONFIG_BLK_DEV_CRYPTOLOOP is not set # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_SX8 is not set # CONFIG_BLK_DEV_UB is not set # CONFIG_BLK_DEV_RAM is not set CONFIG_BLK_DEV_RAM_COUNT=16 CONFIG_INITRAMFS_SOURCE="" # CONFIG_LBD is not set CONFIG_CDROM_PKTCDVD=m CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set
# # IO Schedulers # CONFIG_IOSCHED_NOOP=y CONFIG_IOSCHED_AS=y CONFIG_IOSCHED_DEADLINE=m CONFIG_IOSCHED_CFQ=m # CONFIG_ATA_OVER_ETH is not set
# # ATA/ATAPI/MFM/RLL support # CONFIG_IDE=y CONFIG_BLK_DEV_IDE=y
# # Please see Documentation/ide.txt for help/info on IDE drives # # CONFIG_BLK_DEV_IDE_SATA is not set # CONFIG_BLK_DEV_HD_IDE is not set CONFIG_BLK_DEV_IDEDISK=y # CONFIG_IDEDISK_MULTI_MODE is not set CONFIG_BLK_DEV_IDECD=m # CONFIG_BLK_DEV_IDETAPE is not set CONFIG_BLK_DEV_IDEFLOPPY=m # CONFIG_BLK_DEV_IDESCSI is not set CONFIG_IDE_TASK_IOCTL=y
# # IDE chipset support/bugfixes # # CONFIG_IDE_GENERIC is not set # CONFIG_BLK_DEV_CMD640 is not set # CONFIG_BLK_DEV_IDEPNP is not set CONFIG_BLK_DEV_IDEPCI=y CONFIG_IDEPCI_SHARE_IRQ=y # CONFIG_BLK_DEV_OFFBOARD is not set # CONFIG_BLK_DEV_GENERIC is not set # CONFIG_BLK_DEV_OPTI621 is not set # CONFIG_BLK_DEV_RZ1000 is not set CONFIG_BLK_DEV_IDEDMA_PCI=y # CONFIG_BLK_DEV_IDEDMA_FORCED is not set CONFIG_IDEDMA_PCI_AUTO=y # CONFIG_IDEDMA_ONLYDISK is not set # CONFIG_BLK_DEV_AEC62XX is not set # CONFIG_BLK_DEV_ALI15X3 is not set # CONFIG_BLK_DEV_AMD74XX is not set # CONFIG_BLK_DEV_ATIIXP is not set # CONFIG_BLK_DEV_CMD64X is not set # CONFIG_BLK_DEV_TRIFLEX is not set # CONFIG_BLK_DEV_CY82C693 is not set # CONFIG_BLK_DEV_CS5520 is not set # CONFIG_BLK_DEV_CS5530 is not set # CONFIG_BLK_DEV_HPT34X is not set # CONFIG_BLK_DEV_HPT366 is not set # CONFIG_BLK_DEV_SC1200 is not set # CONFIG_BLK_DEV_PIIX is not set # CONFIG_BLK_DEV_NS87415 is not set # CONFIG_BLK_DEV_PDC202XX_OLD is not set CONFIG_BLK_DEV_PDC202XX_NEW=y # CONFIG_PDC202XX_FORCE is not set # CONFIG_BLK_DEV_SVWKS is not set # CONFIG_BLK_DEV_SIIMAGE is not set # CONFIG_BLK_DEV_SIS5513 is not set # CONFIG_BLK_DEV_SLC90E66 is not set # CONFIG_BLK_DEV_TRM290 is not set CONFIG_BLK_DEV_VIA82CXXX=y # CONFIG_IDE_ARM is not set CONFIG_BLK_DEV_IDEDMA=y # CONFIG_IDEDMA_IVB is not set CONFIG_IDEDMA_AUTO=y # CONFIG_BLK_DEV_HD is not set
# # SCSI device support # CONFIG_SCSI=m # CONFIG_SCSI_PROC_FS is not set
# # SCSI support type (disk, tape, CD-ROM) # CONFIG_BLK_DEV_SD=m # CONFIG_CHR_DEV_ST is not set # CONFIG_CHR_DEV_OSST is not set # CONFIG_BLK_DEV_SR is not set # CONFIG_CHR_DEV_SG is not set # CONFIG_CHR_DEV_SCH is not set
# # Some SCSI devices (e.g. CD jukebox) support multiple LUNs # # CONFIG_SCSI_MULTI_LUN is not set # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set
# # SCSI Transport Attributes # # CONFIG_SCSI_SPI_ATTRS is not set # CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set
# # SCSI low-level drivers # # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ARCMSR is not set # CONFIG_SCSI_ACARD is not set # CONFIG_SCSI_ITERAID is not set # CONFIG_SCSI_AACRAID is not set # CONFIG_SCSI_AIC7XXX is not set # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_DPT_I2O is not set # CONFIG_MEGARAID_NEWGEN is not set # CONFIG_MEGARAID_LEGACY is not set # CONFIG_MEGARAID_SAS is not set # CONFIG_SCSI_SATA is not set # CONFIG_SCSI_BUSLOGIC is not set # CONFIG_SCSI_DMX3191D is not set # CONFIG_SCSI_EATA is not set # CONFIG_SCSI_FUTURE_DOMAIN is not set # CONFIG_SCSI_GDTH is not set # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set # CONFIG_SCSI_PPA is not set # CONFIG_SCSI_IMM is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set # CONFIG_SCSI_QLOGIC_FC is not set # CONFIG_SCSI_QLOGIC_1280 is not set CONFIG_SCSI_QLA2XXX=m # CONFIG_SCSI_QLA21XX is not set # CONFIG_SCSI_QLA22XX is not set # CONFIG_SCSI_QLA2300 is not set # CONFIG_SCSI_QLA2322 is not set # CONFIG_SCSI_QLA6312 is not set # CONFIG_SCSI_LPFC is not set # CONFIG_SCSI_DC395x is not set # CONFIG_SCSI_DC390T is not set # CONFIG_SCSI_NSP32 is not set # CONFIG_SCSI_DEBUG is not set
# # Multi-device support (RAID and LVM) # # CONFIG_MD is not set
# # Fusion MPT device support # # CONFIG_FUSION is not set # CONFIG_FUSION_SPI is not set # CONFIG_FUSION_FC is not set
# # IEEE 1394 (FireWire) support # # CONFIG_IEEE1394 is not set
# # I2O device support # # CONFIG_I2O is not set
# # Networking support # CONFIG_NET=y
# # Networking options # CONFIG_PACKET=m CONFIG_PACKET_MMAP=y CONFIG_UNIX=y CONFIG_NET_KEY=m CONFIG_INET=y CONFIG_IP_MULTICAST=y CONFIG_IP_ADVANCED_ROUTER=y CONFIG_IP_MULTIPLE_TABLES=y CONFIG_IP_ROUTE_FWMARK=y # CONFIG_IP_ROUTE_MULTIPATH is not set CONFIG_IP_ROUTE_VERBOSE=y # CONFIG_IP_PNP is not set CONFIG_NET_IPIP=m CONFIG_NET_IPGRE=m CONFIG_NET_IPGRE_BROADCAST=y CONFIG_IP_MROUTE=y CONFIG_IP_PIMSM_V1=y CONFIG_IP_PIMSM_V2=y # CONFIG_ARPD is not set CONFIG_SYN_COOKIES=y CONFIG_INET_AH=m CONFIG_INET_ESP=m CONFIG_INET_IPCOMP=m CONFIG_INET_TUNNEL=m CONFIG_IP_TCPDIAG=m # CONFIG_IP_TCPDIAG_IPV6 is not set
# # TCP congestion control # # CONFIG_TCP_CONG_BIC is not set # CONFIG_TCP_CONG_WESTWOOD is not set # CONFIG_TCP_CONG_HTCP is not set # CONFIG_TCP_CONG_HSTCP is not set # CONFIG_TCP_CONG_HYBLA is not set # CONFIG_TCP_CONG_VEGAS is not set # CONFIG_TCP_CONG_SCALABLE is not set
# # IP: Virtual Server Configuration # # CONFIG_IP_VS is not set # CONFIG_IPV6 is not set CONFIG_NETFILTER=y # CONFIG_NETFILTER_DEBUG is not set CONFIG_BRIDGE_NETFILTER=y
# # IP: Netfilter Configuration # CONFIG_IP_NF_CONNTRACK=m CONFIG_IP_NF_CT_ACCT=y CONFIG_IP_NF_CONNTRACK_MARK=y CONFIG_IP_NF_CT_PROTO_SCTP=m CONFIG_IP_NF_FTP=m CONFIG_IP_NF_IRC=m CONFIG_IP_NF_TFTP=m CONFIG_IP_NF_AMANDA=m CONFIG_IP_NF_QUEUE=m CONFIG_IP_NF_IPTABLES=m CONFIG_IP_NF_MATCH_LIMIT=m CONFIG_IP_NF_MATCH_IPRANGE=m CONFIG_IP_NF_MATCH_MAC=m CONFIG_IP_NF_MATCH_PKTTYPE=m CONFIG_IP_NF_MATCH_MARK=m CONFIG_IP_NF_MATCH_MULTIPORT=m CONFIG_IP_NF_MATCH_TOS=m CONFIG_IP_NF_MATCH_RECENT=m CONFIG_IP_NF_MATCH_ECN=m CONFIG_IP_NF_MATCH_DSCP=m CONFIG_IP_NF_MATCH_AH_ESP=m CONFIG_IP_NF_MATCH_LENGTH=m CONFIG_IP_NF_MATCH_TTL=m CONFIG_IP_NF_MATCH_TCPMSS=m CONFIG_IP_NF_MATCH_HELPER=m CONFIG_IP_NF_MATCH_STATE=m CONFIG_IP_NF_MATCH_CONNTRACK=m CONFIG_IP_NF_MATCH_OWNER=m CONFIG_IP_NF_MATCH_PHYSDEV=m CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_MATCH_REALM=m CONFIG_IP_NF_MATCH_SCTP=m CONFIG_IP_NF_MATCH_COMMENT=m CONFIG_IP_NF_MATCH_CONNMARK=m CONFIG_IP_NF_MATCH_HASHLIMIT=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m CONFIG_IP_NF_TARGET_LOG=m CONFIG_IP_NF_TARGET_ULOG=m CONFIG_IP_NF_TARGET_TCPMSS=m CONFIG_IP_NF_NAT=m CONFIG_IP_NF_NAT_NEEDED=y CONFIG_IP_NF_TARGET_MASQUERADE=m CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_IP_NF_TARGET_NETMAP=m CONFIG_IP_NF_TARGET_SAME=m CONFIG_IP_NF_NAT_SNMP_BASIC=m CONFIG_IP_NF_NAT_IRC=m CONFIG_IP_NF_NAT_FTP=m CONFIG_IP_NF_NAT_TFTP=m CONFIG_IP_NF_NAT_AMANDA=m CONFIG_IP_NF_MANGLE=m CONFIG_IP_NF_TARGET_TOS=m CONFIG_IP_NF_TARGET_ECN=m CONFIG_IP_NF_TARGET_DSCP=m CONFIG_IP_NF_TARGET_MARK=m CONFIG_IP_NF_TARGET_CLASSIFY=m CONFIG_IP_NF_TARGET_CONNMARK=m # CONFIG_IP_NF_TARGET_CLUSTERIP is not set CONFIG_IP_NF_RAW=m CONFIG_IP_NF_TARGET_NOTRACK=m # CONFIG_IP_NF_ARPTABLES is not set
# # Bridge: Netfilter Configuration # CONFIG_BRIDGE_NF_EBTABLES=m CONFIG_BRIDGE_EBT_BROUTE=m CONFIG_BRIDGE_EBT_T_FILTER=m CONFIG_BRIDGE_EBT_T_NAT=m CONFIG_BRIDGE_EBT_802_3=m CONFIG_BRIDGE_EBT_AMONG=m CONFIG_BRIDGE_EBT_ARP=m CONFIG_BRIDGE_EBT_IP=m CONFIG_BRIDGE_EBT_LIMIT=m CONFIG_BRIDGE_EBT_MARK=m CONFIG_BRIDGE_EBT_PKTTYPE=m CONFIG_BRIDGE_EBT_STP=m CONFIG_BRIDGE_EBT_VLAN=m CONFIG_BRIDGE_EBT_ARPREPLY=m CONFIG_BRIDGE_EBT_DNAT=m CONFIG_BRIDGE_EBT_MARK_T=m CONFIG_BRIDGE_EBT_REDIRECT=m CONFIG_BRIDGE_EBT_SNAT=m CONFIG_BRIDGE_EBT_LOG=m CONFIG_BRIDGE_EBT_ULOG=m CONFIG_XFRM=y CONFIG_XFRM_USER=m
# # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set # CONFIG_ATM is not set CONFIG_BRIDGE=m # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set CONFIG_LLC=m CONFIG_LLC2=m # CONFIG_IPX is not set # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set CONFIG_NET_DIVERT=y # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set
# # QoS and/or fair queueing # # CONFIG_NET_SCHED is not set CONFIG_NET_CLS_ROUTE=y
# # Network testing # # CONFIG_NET_PKTGEN is not set # CONFIG_KGDBOE is not set CONFIG_NETPOLL=y # CONFIG_NETPOLL_RX is not set # CONFIG_NETPOLL_TRAP is not set CONFIG_NET_POLL_CONTROLLER=y # CONFIG_HAMRADIO is not set # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_IEEE80211 is not set CONFIG_NETDEVICES=y CONFIG_DUMMY=m # CONFIG_BONDING is not set # CONFIG_EQUALIZER is not set CONFIG_TUN=m # CONFIG_NET_SB1000 is not set
# # ARCnet devices # # CONFIG_ARCNET is not set
# # Ethernet (10 or 100Mbit) # CONFIG_NET_ETHERNET=y CONFIG_MII=m # CONFIG_HAPPYMEAL is not set # CONFIG_SUNGEM is not set # CONFIG_NET_VENDOR_3COM is not set
# # Tulip family network device support # # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set CONFIG_NET_PCI=y # CONFIG_PCNET32 is not set # CONFIG_AMD8111_ETH is not set # CONFIG_ADAPTEC_STARFIRE is not set # CONFIG_B44 is not set # CONFIG_FORCEDETH is not set # CONFIG_DGRS is not set # CONFIG_EEPRO100 is not set # CONFIG_E100 is not set # CONFIG_FEALNX is not set # CONFIG_NATSEMI is not set # CONFIG_NE2K_PCI is not set # CONFIG_8139CP is not set CONFIG_8139TOO=m # CONFIG_8139TOO_PIO is not set # CONFIG_8139TOO_TUNE_TWISTER is not set # CONFIG_8139TOO_8129 is not set # CONFIG_8139_OLD_RX_RESET is not set # CONFIG_SIS900 is not set # CONFIG_EPIC100 is not set # CONFIG_SUNDANCE is not set # CONFIG_TLAN is not set # CONFIG_VIA_RHINE is not set
# # Ethernet (1000 Mbit) # # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set # CONFIG_R8169 is not set # CONFIG_SKGE is not set # CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set
# # Ethernet (10000 Mbit) # # CONFIG_CHELSIO_T1 is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set
# # Token Ring devices # # CONFIG_TR is not set
# # Wireless LAN (non-hamradio) # CONFIG_NET_RADIO=y
# # Obsolete Wireless cards support (pre-802.11) # # CONFIG_STRIP is not set
# # Wireless 802.11b ISA/PCI cards support # # CONFIG_HERMES is not set # CONFIG_ATMEL is not set
# # Prism GT/Duette 802.11(a/b/g) PCI/Cardbus support # # CONFIG_PRISM54 is not set # CONFIG_HOSTAP is not set CONFIG_NET_WIRELESS=y
# # Wan interfaces # # CONFIG_WAN is not set # CONFIG_FDDI is not set # CONFIG_HIPPI is not set # CONFIG_PLIP is not set CONFIG_PPP=m # CONFIG_PPP_MULTILINK is not set # CONFIG_PPP_FILTER is not set CONFIG_PPP_ASYNC=m # CONFIG_PPP_SYNC_TTY is not set CONFIG_PPP_DEFLATE=m # CONFIG_PPP_BSDCOMP is not set CONFIG_PPP_MPPE=m # CONFIG_PPPOE is not set # CONFIG_SLIP is not set # CONFIG_NET_FC is not set # CONFIG_SHAPER is not set CONFIG_NETCONSOLE=m
# # ISDN subsystem # # CONFIG_ISDN is not set
# # Telephony Support # # CONFIG_PHONE is not set
# # Input device support # CONFIG_INPUT=y
# # Userland interfaces # CONFIG_INPUT_MOUSEDEV=y # CONFIG_INPUT_MOUSEDEV_PSAUX is not set CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # CONFIG_INPUT_JOYDEV is not set # CONFIG_INPUT_TSDEV is not set CONFIG_INPUT_EVDEV=m # CONFIG_INPUT_EVBUG is not set
# # Input Device Drivers # CONFIG_INPUT_KEYBOARD=y CONFIG_KEYBOARD_ATKBD=y # CONFIG_KEYBOARD_SUNKBD is not set # CONFIG_KEYBOARD_LKKBD is not set # CONFIG_KEYBOARD_XTKBD is not set # CONFIG_KEYBOARD_NEWTON is not set CONFIG_INPUT_MOUSE=y CONFIG_MOUSE_PS2=m # CONFIG_MOUSE_SERIAL is not set # CONFIG_MOUSE_VSXXXAA is not set # CONFIG_INPUT_JOYSTICK is not set # CONFIG_INPUT_TOUCHSCREEN is not set CONFIG_INPUT_MISC=y CONFIG_INPUT_PCSPKR=m # CONFIG_INPUT_UINPUT is not set
# # Hardware I/O ports # CONFIG_SERIO=y CONFIG_SERIO_I8042=y # CONFIG_SERIO_SERPORT is not set # CONFIG_SERIO_CT82C710 is not set # CONFIG_SERIO_PARKBD is not set # CONFIG_SERIO_PCIPS2 is not set CONFIG_SERIO_LIBPS2=y # CONFIG_SERIO_RAW is not set # CONFIG_GAMEPORT is not set
# # Character devices # CONFIG_VT=y CONFIG_VT_CONSOLE=y CONFIG_HW_CONSOLE=y # CONFIG_SERIAL_NONSTANDARD is not set
# # Serial drivers # CONFIG_SERIAL_8250=m # CONFIG_SERIAL_8250_ACPI is not set CONFIG_SERIAL_8250_NR_UARTS=4 CONFIG_SERIAL_8250_EXTENDED=y # CONFIG_SERIAL_8250_MANY_PORTS is not set CONFIG_SERIAL_8250_SHARE_IRQ=y CONFIG_SERIAL_8250_DETECT_IRQ=y # CONFIG_SERIAL_8250_MULTIPORT is not set # CONFIG_SERIAL_8250_RSA is not set
# # Non-8250 serial port support # CONFIG_SERIAL_CORE=m # CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y # CONFIG_LEGACY_PTYS is not set # CONFIG_PRINTER is not set # CONFIG_PPDEV is not set # CONFIG_TIPAR is not set
# # IPMI # # CONFIG_IPMI_HANDLER is not set
# # Watchdog Cards # CONFIG_WATCHDOG=y # CONFIG_WATCHDOG_NOWAYOUT is not set
# # Watchdog Device Drivers # # CONFIG_SOFT_WATCHDOG is not set # CONFIG_ACQUIRE_WDT is not set # CONFIG_ADVANTECH_WDT is not set # CONFIG_ALIM1535_WDT is not set # CONFIG_ALIM7101_WDT is not set # CONFIG_SC520_WDT is not set # CONFIG_EUROTECH_WDT is not set # CONFIG_IB700_WDT is not set # CONFIG_WAFER_WDT is not set # CONFIG_I8XX_TCO is not set # CONFIG_I6300ESB_WDT is not set # CONFIG_SC1200_WDT is not set # CONFIG_60XX_WDT is not set # CONFIG_CPU5_WDT is not set CONFIG_W83627HF_WDT=m # CONFIG_W83877F_WDT is not set # CONFIG_MACHZ_WDT is not set
# # PCI-based Watchdog Cards # # CONFIG_PCIPCWATCHDOG is not set # CONFIG_WDTPCI is not set
# # USB-based Watchdog Cards # # CONFIG_USBPCWATCHDOG is not set # CONFIG_HW_RANDOM is not set CONFIG_NVRAM=m CONFIG_RTC=m # CONFIG_GEN_RTC is not set # CONFIG_DTLK is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set # CONFIG_SONYPI is not set
# # Ftape, the floppy tape device driver # # CONFIG_FTAPE is not set CONFIG_AGP=m # CONFIG_AGP_ALI is not set # CONFIG_AGP_ATI is not set # CONFIG_AGP_AMD is not set # CONFIG_AGP_AMD64 is not set # CONFIG_AGP_INTEL is not set # CONFIG_AGP_NVIDIA is not set # CONFIG_AGP_SIS is not set # CONFIG_AGP_SWORKS is not set CONFIG_AGP_VIA=m # CONFIG_AGP_EFFICEON is not set # CONFIG_DRM is not set # CONFIG_MWAVE is not set # CONFIG_RAW_DRIVER is not set # CONFIG_HPET is not set # CONFIG_HANGCHECK_TIMER is not set
# # TPM devices # # CONFIG_TCG_TPM is not set
# # I2C support # CONFIG_I2C=y CONFIG_I2C_CHARDEV=m
# # I2C Algorithms # # CONFIG_I2C_ALGOBIT is not set # CONFIG_I2C_ALGOPCF is not set # CONFIG_I2C_ALGOPCA is not set
# # I2C Hardware Bus support # # CONFIG_I2C_ALI1535 is not set # CONFIG_I2C_ALI1563 is not set # CONFIG_I2C_ALI15X3 is not set # CONFIG_I2C_AMD756 is not set # CONFIG_I2C_AMD8111 is not set # CONFIG_I2C_I801 is not set # CONFIG_I2C_I810 is not set # CONFIG_I2C_PIIX4 is not set CONFIG_I2C_ISA=m # CONFIG_I2C_NFORCE2 is not set # CONFIG_I2C_PARPORT is not set # CONFIG_I2C_PARPORT_LIGHT is not set # CONFIG_I2C_PROSAVAGE is not set # CONFIG_I2C_SAVAGE4 is not set # CONFIG_SCx200_ACB is not set # CONFIG_I2C_SIS5595 is not set # CONFIG_I2C_SIS630 is not set # CONFIG_I2C_SIS96X is not set # CONFIG_I2C_STUB is not set # CONFIG_I2C_VIA is not set # CONFIG_I2C_VIAPRO is not set # CONFIG_I2C_VOODOO3 is not set # CONFIG_I2C_PCA_ISA is not set
# # Hardware Sensors Chip support # CONFIG_I2C_SENSOR=m # CONFIG_SENSORS_ADM1021 is not set # CONFIG_SENSORS_ADM1025 is not set # CONFIG_SENSORS_ADM1026 is not set # CONFIG_SENSORS_ADM1031 is not set # CONFIG_SENSORS_ADM9240 is not set # CONFIG_SENSORS_ASB100 is not set # CONFIG_SENSORS_ATXP1 is not set # CONFIG_SENSORS_DS1621 is not set # CONFIG_SENSORS_FSCHER is not set # CONFIG_SENSORS_FSCPOS is not set # CONFIG_SENSORS_GL518SM is not set # CONFIG_SENSORS_GL520SM is not set # CONFIG_SENSORS_IT87 is not set # CONFIG_SENSORS_LM63 is not set # CONFIG_SENSORS_LM75 is not set # CONFIG_SENSORS_LM77 is not set # CONFIG_SENSORS_LM78 is not set # CONFIG_SENSORS_LM80 is not set # CONFIG_SENSORS_LM83 is not set # CONFIG_SENSORS_LM85 is not set # CONFIG_SENSORS_LM87 is not set # CONFIG_SENSORS_LM90 is not set # CONFIG_SENSORS_LM92 is not set # CONFIG_SENSORS_MAX1619 is not set # CONFIG_SENSORS_PC87360 is not set # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_SIS5595 is not set # CONFIG_SENSORS_SMSC47M1 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_W83781D is not set # CONFIG_SENSORS_W83L785TS is not set CONFIG_SENSORS_W83627HF=m # CONFIG_SENSORS_W83627EHF is not set
# # Other I2C Chip support # # CONFIG_SENSORS_DS1337 is not set # CONFIG_SENSORS_DS1374 is not set # CONFIG_SENSORS_EEPROM is not set # CONFIG_SENSORS_PCF8574 is not set # CONFIG_SENSORS_PCA9539 is not set # CONFIG_SENSORS_PCF8591 is not set # CONFIG_SENSORS_RTC8564 is not set # CONFIG_SENSORS_MAX6875 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set
# # Dallas's 1-wire bus # # CONFIG_W1 is not set
# # Misc devices # # CONFIG_IBM_ASM is not set
# # Multimedia devices # CONFIG_VIDEO_DEV=m
# # Video For Linux #
# # Video Adapters # # CONFIG_CONFIG_TUNER_MULTI_I2C is not set # CONFIG_VIDEO_BT848 is not set # CONFIG_VIDEO_BWQCAM is not set # CONFIG_VIDEO_CQCAM is not set # CONFIG_VIDEO_W9966 is not set # CONFIG_VIDEO_CPIA is not set # CONFIG_VIDEO_SAA5246A is not set # CONFIG_VIDEO_SAA5249 is not set # CONFIG_TUNER_3036 is not set # CONFIG_VIDEO_STRADIS is not set CONFIG_VIDEO_SAA7134=m # CONFIG_VIDEO_MXB is not set # CONFIG_VIDEO_DPC is not set # CONFIG_VIDEO_HEXIUM_ORION is not set # CONFIG_VIDEO_HEXIUM_GEMINI is not set # CONFIG_VIDEO_CX88 is not set # CONFIG_VIDEO_OVCAMCHIP is not set
# # Radio Adapters # # CONFIG_RADIO_GEMTEK_PCI is not set # CONFIG_RADIO_MAXIRADIO is not set # CONFIG_RADIO_MAESTRO is not set
# # Digital Video Broadcasting Devices # # CONFIG_DVB is not set CONFIG_VIDEO_TUNER=m CONFIG_VIDEO_BUF=m CONFIG_VIDEO_IR=m
# # Graphics support # # CONFIG_FB is not set # CONFIG_VIDEO_SELECT is not set
# # Console display driver support # CONFIG_VGA_CONSOLE=y CONFIG_DUMMY_CONSOLE=y
# # Sound # CONFIG_SOUND=m
# # Advanced Linux Sound Architecture # CONFIG_SND=m CONFIG_SND_TIMER=m CONFIG_SND_PCM=m CONFIG_SND_RAWMIDI=m CONFIG_SND_SEQUENCER=m # CONFIG_SND_SEQ_DUMMY is not set CONFIG_SND_OSSEMUL=y CONFIG_SND_MIXER_OSS=m CONFIG_SND_PCM_OSS=m CONFIG_SND_SEQUENCER_OSS=y CONFIG_SND_RTCTIMER=m # CONFIG_SND_VERBOSE_PRINTK is not set # CONFIG_SND_DEBUG is not set
# # Generic devices # CONFIG_SND_MPU401_UART=m # CONFIG_SND_DUMMY is not set # CONFIG_SND_VIRMIDI is not set # CONFIG_SND_MTPAV is not set # CONFIG_SND_SERIAL_U16550 is not set # CONFIG_SND_MPU401 is not set
# # PCI devices # CONFIG_SND_AC97_CODEC=m # CONFIG_SND_ALI5451 is not set # CONFIG_SND_ATIIXP is not set # CONFIG_SND_ATIIXP_MODEM is not set # CONFIG_SND_AU8810 is not set # CONFIG_SND_AU8820 is not set # CONFIG_SND_AU8830 is not set # CONFIG_SND_AZT3328 is not set # CONFIG_SND_BT87X is not set # CONFIG_SND_CS46XX is not set # CONFIG_SND_CS4281 is not set # CONFIG_SND_EMU10K1 is not set # CONFIG_SND_EMU10K1X is not set # CONFIG_SND_CA0106 is not set # CONFIG_SND_KORG1212 is not set # CONFIG_SND_MIXART is not set # CONFIG_SND_NM256 is not set # CONFIG_SND_RME32 is not set # CONFIG_SND_RME96 is not set # CONFIG_SND_RME9652 is not set # CONFIG_SND_HDSP is not set # CONFIG_SND_TRIDENT is not set # CONFIG_SND_YMFPCI is not set # CONFIG_SND_ALS4000 is not set # CONFIG_SND_CMIPCI is not set # CONFIG_SND_ENS1370 is not set # CONFIG_SND_ENS1371 is not set # CONFIG_SND_ES1938 is not set # CONFIG_SND_ES1968 is not set # CONFIG_SND_MAESTRO3 is not set # CONFIG_SND_FM801 is not set # CONFIG_SND_ICE1712 is not set # CONFIG_SND_ICE1724 is not set # CONFIG_SND_INTEL8X0 is not set # CONFIG_SND_INTEL8X0M is not set # CONFIG_SND_SONICVIBES is not set CONFIG_SND_VIA82XX=m # CONFIG_SND_VIA82XX_MODEM is not set # CONFIG_SND_VX222 is not set # CONFIG_SND_HDA_INTEL is not set
# # USB devices # # CONFIG_SND_USB_AUDIO is not set # CONFIG_SND_USB_USX2Y is not set
# # Open Sound System # # CONFIG_SOUND_PRIME is not set
# # USB support # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y CONFIG_USB=m # CONFIG_USB_DEBUG is not set
# # Miscellaneous USB options # CONFIG_USB_DEVICEFS=y # CONFIG_USB_BANDWIDTH is not set # CONFIG_USB_DYNAMIC_MINORS is not set # CONFIG_USB_SUSPEND is not set # CONFIG_USB_OTG is not set
# # USB Host Controller Drivers # # CONFIG_USB_EHCI_HCD is not set # CONFIG_USB_ISP116X_HCD is not set # CONFIG_USB_OHCI_HCD is not set CONFIG_USB_UHCI_HCD=m # CONFIG_USB_SL811_HCD is not set
# # USB Device Class drivers # # CONFIG_USB_AUDIO is not set # CONFIG_USB_BLUETOOTH_TTY is not set # CONFIG_USB_MIDI is not set # CONFIG_USB_ACM is not set CONFIG_USB_PRINTER=m
# # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' may also be needed; see USB_STORAGE Help for more information # CONFIG_USB_STORAGE=m # CONFIG_USB_STORAGE_DEBUG is not set # CONFIG_USB_STORAGE_DATAFAB is not set # CONFIG_USB_STORAGE_FREECOM is not set # CONFIG_USB_STORAGE_ISD200 is not set # CONFIG_USB_STORAGE_DPCM is not set # CONFIG_USB_STORAGE_USBAT is not set # CONFIG_USB_STORAGE_SDDR09 is not set # CONFIG_USB_STORAGE_SDDR55 is not set # CONFIG_USB_STORAGE_JUMPSHOT is not set
# # USB Input Devices # CONFIG_USB_HID=m CONFIG_USB_HIDINPUT=y # CONFIG_HID_FF is not set # CONFIG_USB_HIDDEV is not set
# # USB HID Boot Protocol drivers # # CONFIG_USB_KBD is not set # CONFIG_USB_MOUSE is not set # CONFIG_USB_AIPTEK is not set # CONFIG_USB_WACOM is not set # CONFIG_USB_ACECAD is not set # CONFIG_USB_KBTAB is not set # CONFIG_USB_POWERMATE is not set # CONFIG_USB_MTOUCH is not set # CONFIG_USB_ITMTOUCH is not set # CONFIG_USB_EGALAX is not set # CONFIG_USB_XPAD is not set # CONFIG_USB_ATI_REMOTE is not set
# # USB Imaging devices # # CONFIG_USB_MDC800 is not set # CONFIG_USB_MICROTEK is not set
# # USB Multimedia devices # # CONFIG_USB_DABUSB is not set # CONFIG_USB_VICAM is not set # CONFIG_USB_DSBR is not set # CONFIG_USB_IBMCAM is not set # CONFIG_USB_KONICAWC is not set # CONFIG_USB_OV511 is not set # CONFIG_USB_SE401 is not set # CONFIG_USB_SN9C102 is not set # CONFIG_USB_STV680 is not set # CONFIG_USB_PWC is not set
# # USB Network Adapters # # CONFIG_USB_CATC is not set # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set # CONFIG_USB_USBNET is not set # CONFIG_USB_ZD1201 is not set # CONFIG_USB_MON is not set
# # USB port drivers # # CONFIG_USB_USS720 is not set
# # USB Serial Converter support # # CONFIG_USB_SERIAL is not set
# # USB Miscellaneous drivers # # CONFIG_USB_EMI62 is not set # CONFIG_USB_EMI26 is not set # CONFIG_USB_AUERSWALD is not set # CONFIG_USB_RIO500 is not set # CONFIG_USB_LEGOTOWER is not set # CONFIG_USB_LCD is not set # CONFIG_USB_LED is not set # CONFIG_USB_CYTHERM is not set # CONFIG_USB_GOTEMP is not set # CONFIG_USB_PHIDGETKIT is not set # CONFIG_USB_PHIDGETSERVO is not set # CONFIG_USB_IDMOUSE is not set # CONFIG_USB_TEST is not set
# # USB DSL modem support #
# # USB Gadget Support # # CONFIG_USB_GADGET is not set
# # MMC/SD Card support # # CONFIG_MMC is not set
# # InfiniBand support # # CONFIG_INFINIBAND is not set
# # SN Devices #
# # Distributed Lock Manager # # CONFIG_DLM is not set
# # File systems # CONFIG_EXT2_FS=m CONFIG_EXT2_FS_XATTR=y CONFIG_EXT2_FS_POSIX_ACL=y # CONFIG_EXT2_FS_SECURITY is not set # CONFIG_EXT2_FS_XIP is not set # CONFIG_EXT3_FS is not set # CONFIG_JBD is not set CONFIG_FS_MBCACHE=m CONFIG_REISERFS_FS=y # CONFIG_REISERFS_CHECK is not set # CONFIG_REISERFS_PROC_INFO is not set CONFIG_REISERFS_FS_XATTR=y CONFIG_REISERFS_FS_POSIX_ACL=y # CONFIG_REISERFS_FS_SECURITY is not set # CONFIG_JFS_FS is not set CONFIG_FS_POSIX_ACL=y
# # XFS support # # CONFIG_XFS_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_MINIX_FS is not set # CONFIG_ROMFS_FS is not set CONFIG_INOTIFY=y # CONFIG_QUOTA is not set CONFIG_DNOTIFY=y # CONFIG_AUTOFS_FS is not set # CONFIG_AUTOFS4_FS is not set
# # Caches # # CONFIG_FSCACHE is not set CONFIG_FUSE_FS=m
# # CD-ROM/DVD Filesystems # CONFIG_ISO9660_FS=m CONFIG_JOLIET=y CONFIG_ZISOFS=y CONFIG_ZISOFS_FS=m CONFIG_UDF_FS=m CONFIG_UDF_NLS=y
# # DOS/FAT/NT Filesystems # CONFIG_FAT_FS=m CONFIG_MSDOS_FS=m CONFIG_VFAT_FS=m CONFIG_FAT_DEFAULT_CODEPAGE=437 CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-15" # CONFIG_NTFS_FS is not set
# # Pseudo filesystems # CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_SYSFS=y # CONFIG_DEVFS_FS is not set CONFIG_DEVPTS_FS_XATTR=y # CONFIG_DEVPTS_FS_SECURITY is not set CONFIG_TMPFS=y CONFIG_TMPFS_XATTR=y # CONFIG_TMPFS_SECURITY is not set CONFIG_HUGETLBFS=y CONFIG_HUGETLB_PAGE=y CONFIG_RAMFS=y CONFIG_CONFIGFS_FS=m # CONFIG_RELAYFS_FS is not set
# # Miscellaneous filesystems # # CONFIG_ADFS_FS is not set # CONFIG_AFFS_FS is not set # CONFIG_HFS_FS is not set # CONFIG_HFSPLUS_FS is not set # CONFIG_BEFS_FS is not set # CONFIG_BFS_FS is not set # CONFIG_EFS_FS is not set CONFIG_CRAMFS=m # CONFIG_VXFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set
# # Network File Systems # # CONFIG_NFS_FS is not set # CONFIG_NFSD is not set CONFIG_SMB_FS=m CONFIG_SMB_NLS_DEFAULT=y CONFIG_SMB_NLS_REMOTE="utf8" CONFIG_CIFS=m # CONFIG_CIFS_STATS is not set CONFIG_CIFS_XATTR=y CONFIG_CIFS_POSIX=y CONFIG_CIFS_EXPERIMENTAL=y # CONFIG_NCP_FS is not set # CONFIG_CODA_FS is not set # CONFIG_AFS_FS is not set # CONFIG_9P_FS is not set
# # Partition Types # # CONFIG_PARTITION_ADVANCED is not set CONFIG_MSDOS_PARTITION=y
# # Native Language Support # CONFIG_NLS=m CONFIG_NLS_DEFAULT="utf8" CONFIG_NLS_CODEPAGE_437=m # CONFIG_NLS_CODEPAGE_737 is not set # CONFIG_NLS_CODEPAGE_775 is not set CONFIG_NLS_CODEPAGE_850=m # CONFIG_NLS_CODEPAGE_852 is not set # CONFIG_NLS_CODEPAGE_855 is not set # CONFIG_NLS_CODEPAGE_857 is not set # CONFIG_NLS_CODEPAGE_860 is not set # CONFIG_NLS_CODEPAGE_861 is not set # CONFIG_NLS_CODEPAGE_862 is not set # CONFIG_NLS_CODEPAGE_863 is not set # CONFIG_NLS_CODEPAGE_864 is not set # CONFIG_NLS_CODEPAGE_865 is not set # CONFIG_NLS_CODEPAGE_866 is not set # CONFIG_NLS_CODEPAGE_869 is not set # CONFIG_NLS_CODEPAGE_936 is not set # CONFIG_NLS_CODEPAGE_950 is not set # CONFIG_NLS_CODEPAGE_932 is not set # CONFIG_NLS_CODEPAGE_949 is not set # CONFIG_NLS_CODEPAGE_874 is not set # CONFIG_NLS_ISO8859_8 is not set # CONFIG_NLS_CODEPAGE_1250 is not set # CONFIG_NLS_CODEPAGE_1251 is not set CONFIG_NLS_ASCII=m CONFIG_NLS_ISO8859_1=m # CONFIG_NLS_ISO8859_2 is not set # CONFIG_NLS_ISO8859_3 is not set # CONFIG_NLS_ISO8859_4 is not set # CONFIG_NLS_ISO8859_5 is not set # CONFIG_NLS_ISO8859_6 is not set # CONFIG_NLS_ISO8859_7 is not set # CONFIG_NLS_ISO8859_9 is not set # CONFIG_NLS_ISO8859_13 is not set # CONFIG_NLS_ISO8859_14 is not set CONFIG_NLS_ISO8859_15=m # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set CONFIG_NLS_UTF8=m
# # Profiling support # # CONFIG_PROFILING is not set
# # Kernel hacking # # CONFIG_PRINTK_TIME is not set CONFIG_DEBUG_KERNEL=y CONFIG_MAGIC_SYSRQ=y CONFIG_LOG_BUF_SHIFT=14 # CONFIG_DETECT_SOFTLOCKUP is not set # CONFIG_SCHEDSTATS is not set # CONFIG_DEBUG_SLAB is not set # CONFIG_DEBUG_SPINLOCK is not set # CONFIG_DEBUG_SPINLOCK_SLEEP is not set # CONFIG_DEBUG_KOBJECT is not set CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_DEBUG_INFO is not set # CONFIG_PAGE_OWNER is not set # CONFIG_DEBUG_FS is not set # CONFIG_FRAME_POINTER is not set CONFIG_EARLY_PRINTK=y # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_KPROBES is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set CONFIG_4KSTACKS=y CONFIG_X86_FIND_SMP_CONFIG=y CONFIG_X86_MPPARSE=y # CONFIG_KGDB is not set
# # Security options # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set
# # Cryptographic options # CONFIG_CRYPTO=y CONFIG_CRYPTO_HMAC=y CONFIG_CRYPTO_NULL=m CONFIG_CRYPTO_MD4=m CONFIG_CRYPTO_MD5=m CONFIG_CRYPTO_SHA1=m CONFIG_CRYPTO_SHA256=m CONFIG_CRYPTO_SHA512=m CONFIG_CRYPTO_WP512=m CONFIG_CRYPTO_TGR192=m CONFIG_CRYPTO_DES=m CONFIG_CRYPTO_BLOWFISH=m CONFIG_CRYPTO_TWOFISH=m CONFIG_CRYPTO_SERPENT=m CONFIG_CRYPTO_AES_586=m CONFIG_CRYPTO_CAST5=m CONFIG_CRYPTO_CAST6=m CONFIG_CRYPTO_TEA=m CONFIG_CRYPTO_ARC4=m CONFIG_CRYPTO_KHAZAD=m CONFIG_CRYPTO_ANUBIS=m CONFIG_CRYPTO_DEFLATE=m CONFIG_CRYPTO_MICHAEL_MIC=m CONFIG_CRYPTO_CRC32C=m # CONFIG_CRYPTO_TEST is not set
# # Hardware crypto devices # # CONFIG_CRYPTO_DEV_PADLOCK is not set
# # Library routines # CONFIG_CRC_CCITT=m CONFIG_CRC32=m CONFIG_LIBCRC32C=m CONFIG_ZLIB_INFLATE=m CONFIG_ZLIB_DEFLATE=m CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y CONFIG_X86_BIOS_REBOOT=y CONFIG_PC=y
Full dmesg: Jun 20 23:30:15 perenold kernel: Linux version 2.6.12-mm1 (root@perenold) (version gcc 3.4.5 20050605 (prerelease) (Debian 3.4.4-0)) #1 Mon Jun 20 23:17:10 CEST 2005 Jun 20 23:30:15 perenold kernel: BIOS-provided physical RAM map: Jun 20 23:30:15 perenold kernel: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) Jun 20 23:30:15 perenold kernel: BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) Jun 20 23:30:15 perenold kernel: BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) Jun 20 23:30:15 perenold kernel: BIOS-e820: 0000000000100000 - 000000001fff0000 (usable) Jun 20 23:30:15 perenold kernel: BIOS-e820: 000000001fff0000 - 000000001fff8000 (ACPI data) Jun 20 23:30:15 perenold kernel: BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS) Jun 20 23:30:15 perenold kernel: BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) Jun 20 23:30:15 perenold kernel: BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) Jun 20 23:30:15 perenold kernel: BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) Jun 20 23:30:15 perenold kernel: 511MB LOWMEM available. Jun 20 23:30:15 perenold kernel: found SMP MP-table at 000fb880 Jun 20 23:30:15 perenold kernel: On node 0 totalpages: 131056 Jun 20 23:30:15 perenold kernel: DMA zone: 4096 pages, LIFO batch:1 Jun 20 23:30:15 perenold kernel: Normal zone: 126960 pages, LIFO batch:31 Jun 20 23:30:15 perenold kernel: HighMem zone: 0 pages, LIFO batch:1 Jun 20 23:30:15 perenold kernel: DMI 2.3 present. Jun 20 23:30:15 perenold kernel: ACPI: RSDP (v000 AMI ) @ 0x000fa710 Jun 20 23:30:15 perenold kernel: ACPI: RSDT (v001 AMIINT VIA_K7 0x00000010 MSFT 0x00000097) @ 0x1fff0000 Jun 20 23:30:15 perenold kernel: ACPI: FADT (v001 AMIINT VIA_K7 0x00000011 MSFT 0x00000097) @ 0x1fff0030 Jun 20 23:30:15 perenold kernel: ACPI: MADT (v001 AMIINT VIA_K7 0x00000009 MSFT 0x00000097) @ 0x1fff00c0 Jun 20 23:30:15 perenold kernel: ACPI: DSDT (v001 VIA VIA_K7 0x00001000 MSFT 0x0100000d) @ 0x00000000 Jun 20 23:30:15 perenold kernel: ACPI: Local APIC address 0xfee00000 Jun 20 23:30:15 perenold kernel: ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Jun 20 23:30:15 perenold kernel: Processor #0 6:6 APIC version 16 Jun 20 23:30:15 perenold kernel: ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) Jun 20 23:30:15 perenold kernel: IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 Jun 20 23:30:15 perenold kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) Jun 20 23:30:15 perenold kernel: ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) Jun 20 23:30:15 perenold kernel: ACPI: IRQ0 used by override. Jun 20 23:30:15 perenold kernel: ACPI: IRQ2 used by override. Jun 20 23:30:15 perenold kernel: ACPI: IRQ9 used by override. Jun 20 23:30:15 perenold kernel: Enabling APIC mode: Flat. Using 1 I/O APICs Jun 20 23:30:15 perenold kernel: Using ACPI (MADT) for SMP configuration information Jun 20 23:30:15 perenold kernel: Allocating PCI resources starting at 20000000 (gap: 20000000:dec00000) Jun 20 23:30:15 perenold kernel: Built 1 zonelists Jun 20 23:30:15 perenold kernel: mapped APIC to ffffd000 (fee00000) Jun 20 23:30:15 perenold kernel: mapped IOAPIC to ffffc000 (fec00000) Jun 20 23:30:15 perenold kernel: Initializing CPU#0 Jun 20 23:30:15 perenold kernel: Kernel command line: root=/dev/hda5 ro Jun 20 23:30:15 perenold kernel: CPU 0 irqstacks, hard=c0362000 soft=c0361000 Jun 20 23:30:15 perenold kernel: PID hash table entries: 2048 (order: 11, 32768 bytes) Jun 20 23:30:15 perenold kernel: Detected 1399.508 MHz processor. Jun 20 23:30:15 perenold kernel: Using tsc for high-res timesource Jun 20 23:30:15 perenold kernel: Console: colour VGA+ 80x25 Jun 20 23:30:15 perenold kernel: Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Jun 20 23:30:15 perenold kernel: Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Jun 20 23:30:15 perenold kernel: Memory: 516148k/524224k available (1569k kernel code, 7524k reserved, 703k data, 136k init, 0k highmem) Jun 20 23:30:15 perenold kernel: Checking if this processor honours the WP bit even in supervisor mode... Ok. Jun 20 23:30:15 perenold kernel: Calibrating delay using timer specific routine.. 2803.82 BogoMIPS (lpj=5607650) Jun 20 23:30:15 perenold kernel: Mount-cache hash table entries: 512 Jun 20 23:30:15 perenold kernel: CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000 Jun 20 23:30:15 perenold kernel: CPU: After vendor identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000 Jun 20 23:30:15 perenold kernel: CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) Jun 20 23:30:15 perenold kernel: CPU: L2 Cache: 256K (64 bytes/line) Jun 20 23:30:15 perenold kernel: CPU: After all inits, caps: 0383fbff c1cbfbff 00000000 00000020 00000000 00000000 00000000 Jun 20 23:30:15 perenold kernel: Intel machine check architecture supported. Jun 20 23:30:15 perenold kernel: Intel machine check reporting enabled on CPU#0. Jun 20 23:30:15 perenold kernel: CPU: AMD Athlon(tm) XP 1600+ stepping 02 Jun 20 23:30:15 perenold kernel: Enabling fast FPU save and restore... done. Jun 20 23:30:15 perenold kernel: Enabling unmasked SIMD FPU exception support... done. Jun 20 23:30:15 perenold kernel: Checking 'hlt' instruction... OK. Jun 20 23:30:15 perenold kernel: ENABLING IO-APIC IRQs Jun 20 23:30:15 perenold kernel: ..TIMER: vector=0x31 pin1=2 pin2=-1 Jun 20 23:30:15 perenold kernel: NET: Registered protocol family 16 Jun 20 23:30:15 perenold kernel: PCI: PCI BIOS revision 2.10 entry at 0xfdb21, last bus=1 Jun 20 23:30:15 perenold kernel: PCI: Using configuration type 1 Jun 20 23:30:15 perenold kernel: mtrr: v2.0 (20020519) Jun 20 23:30:15 perenold kernel: ACPI: Subsystem revision 20050309 Jun 20 23:30:15 perenold kernel: ACPI: Interpreter enabled Jun 20 23:30:15 perenold kernel: ACPI: Using IOAPIC for interrupt routing Jun 20 23:30:15 perenold kernel: ACPI: PCI Root Bridge [PCI0] (0000:00) Jun 20 23:30:15 perenold kernel: PCI: Probing PCI hardware (bus 00) Jun 20 23:30:15 perenold kernel: Boot video device is 0000:01:00.0 Jun 20 23:30:15 perenold kernel: ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] Jun 20 23:30:15 perenold kernel: ACPI: Power Resource [URP1] (off) Jun 20 23:30:15 perenold kernel: ACPI: Power Resource [URP2] (off) Jun 20 23:30:15 perenold kernel: ACPI: Power Resource [FDDP] (off) Jun 20 23:30:15 perenold kernel: ACPI: Power Resource [LPTP] (off) Jun 20 23:30:15 perenold kernel: ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15) Jun 20 23:30:15 perenold kernel: ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15) Jun 20 23:30:15 perenold kernel: ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 *12 14 15) Jun 20 23:30:15 perenold kernel: ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15) Jun 20 23:30:15 perenold kernel: Linux Plug and Play Support v0.97 (c) Adam Belay Jun 20 23:30:15 perenold kernel: pnp: PnP ACPI init Jun 20 23:30:15 perenold kernel: pnp: PnP ACPI: found 10 devices Jun 20 23:30:15 perenold kernel: PCI: Using ACPI for IRQ routing Jun 20 23:30:15 perenold kernel: PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report Jun 20 23:30:15 perenold kernel: PCI: Bridge: 0000:00:01.0 Jun 20 23:30:15 perenold kernel: IO window: disabled. Jun 20 23:30:15 perenold kernel: MEM window: dde00000-dfefffff Jun 20 23:30:15 perenold kernel: PREFETCH window: d9c00000-ddcfffff Jun 20 23:30:15 perenold kernel: PCI: Setting latency timer of device 0000:00:01.0 to 64 Jun 20 23:30:15 perenold kernel: Machine check exception polling timer started. Jun 20 23:30:15 perenold kernel: Total HugeTLB memory allocated, 0 Jun 20 23:30:15 perenold kernel: inotify device minor=63 Jun 20 23:30:15 perenold kernel: Initializing Cryptographic API Jun 20 23:30:15 perenold kernel: cn_fork is registered Jun 20 23:30:15 perenold kernel: PNP: PS/2 controller doesn't have AUX irq; using default 0xc Jun 20 23:30:15 perenold kernel: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1,12 Jun 20 23:30:15 perenold kernel: serio: i8042 AUX port at 0x60,0x64 irq 12 Jun 20 23:30:15 perenold kernel: serio: i8042 KBD port at 0x60,0x64 irq 1 Jun 20 23:30:15 perenold kernel: io scheduler noop registered Jun 20 23:30:15 perenold kernel: io scheduler anticipatory registered Jun 20 23:30:15 perenold kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 Jun 20 23:30:15 perenold kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Jun 20 23:30:15 perenold kernel: PDC20268: IDE controller at PCI slot 0000:00:06.0 Jun 20 23:30:15 perenold kernel: ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 17 (level, low) -> IRQ 16 Jun 20 23:30:15 perenold kernel: PDC20268: chipset revision 2 Jun 20 23:30:15 perenold kernel: PDC20268: ROM enabled at 0x20000000 Jun 20 23:30:15 perenold kernel: PDC20268: 100% native mode on irq 16 Jun 20 23:30:15 perenold kernel: ide2: BM-DMA at 0xdc00-0xdc07, BIOS settings: hde:pio, hdf:pio Jun 20 23:30:15 perenold kernel: ide3: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdg:pio, hdh:pio Jun 20 23:30:15 perenold kernel: Probing IDE interface ide2... Jun 20 23:30:15 perenold kernel: Probing IDE interface ide3... Jun 20 23:30:15 perenold kernel: hdg: IC35L040AVVA07-0, ATA DISK drive Jun 20 23:30:15 perenold kernel: ide3 at 0xe400-0xe407,0xe002 on irq 16 Jun 20 23:30:15 perenold kernel: VP_IDE: IDE controller at PCI slot 0000:00:11.1 Jun 20 23:30:15 perenold kernel: PCI: Via IRQ fixup for 0000:00:11.1, from 255 to 0 Jun 20 23:30:15 perenold kernel: VP_IDE: chipset revision 6 Jun 20 23:30:15 perenold kernel: VP_IDE: not 100% native mode: will probe irqs later Jun 20 23:30:15 perenold kernel: VP_IDE: VIA vt8233 (rev 00) IDE UDMA100 controller on pci0000:00:11.1 Jun 20 23:30:15 perenold kernel: ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio Jun 20 23:30:15 perenold kernel: ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA Jun 20 23:30:15 perenold kernel: Probing IDE interface ide0... Jun 20 23:30:15 perenold kernel: hda: WDC WD400BB-75AUA1, ATA DISK drive Jun 20 23:30:15 perenold kernel: hdb: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive Jun 20 23:30:15 perenold kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Jun 20 23:30:15 perenold kernel: Probing IDE interface ide1... Jun 20 23:30:15 perenold kernel: hdc: TOSHIBA DVD-ROM SD-M1212, ATAPI CD/DVD-ROM drive Jun 20 23:30:15 perenold kernel: hdd: PLEXTOR CD-R PX-W2410A, ATAPI CD/DVD-ROM drive Jun 20 23:30:15 perenold kernel: ide1 at 0x170-0x177,0x376 on irq 15 Jun 20 23:30:15 perenold kernel: hdg: max request size: 128KiB Jun 20 23:30:15 perenold kernel: hdg: 80418240 sectors (41174 MB) w/1863KiB Cache, CHS=65535/16/63, UDMA(100) Jun 20 23:30:15 perenold kernel: hdg: cache flushes supported Jun 20 23:30:15 perenold kernel: hdg: hdg1 Jun 20 23:30:15 perenold kernel: hda: max request size: 128KiB Jun 20 23:30:15 perenold kernel: hda: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100) Jun 20 23:30:15 perenold kernel: hda: cache flushes not supported Jun 20 23:30:15 perenold kernel: hda: hda1 hda2 < hda5 hda6 hda7 hda8 > Jun 20 23:30:15 perenold kernel: mice: PS/2 mouse device common for all mice Jun 20 23:30:15 perenold kernel: NET: Registered protocol family 2 Jun 20 23:30:15 perenold kernel: IP: routing cache hash table of 4096 buckets, 32Kbytes Jun 20 23:30:15 perenold kernel: TCP established hash table entries: 32768 (order: 6, 262144 bytes) Jun 20 23:30:15 perenold kernel: TCP bind hash table entries: 32768 (order: 5, 131072 bytes) Jun 20 23:30:15 perenold kernel: TCP: Hash tables configured (established 32768 bind 32768) Jun 20 23:30:15 perenold kernel: TCP reno registered Jun 20 23:30:15 perenold kernel: NET: Registered protocol family 1 Jun 20 23:30:15 perenold kernel: Using IPI Shortcut mode Jun 20 23:30:15 perenold kernel: ReiserFS: hda5: found reiserfs format "3.6" with standard journal Jun 20 23:30:15 perenold kernel: input: AT Translated Set 2 keyboard on isa0060/serio0 Jun 20 23:30:15 perenold kernel: ReiserFS: hda5: using ordered data mode Jun 20 23:30:15 perenold kernel: ReiserFS: hda5: journal params: device hda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 Jun 20 23:30:15 perenold kernel: ReiserFS: hda5: checking transaction log (hda5) Jun 20 23:30:15 perenold kernel: ReiserFS: hda5: Using r5 hash to sort names Jun 20 23:30:15 perenold kernel: VFS: Mounted root (reiserfs filesystem) readonly. Jun 20 23:30:15 perenold kernel: Freeing unused kernel memory: 136k freed Jun 20 23:30:15 perenold kernel: Adding 497972k swap on /dev/hda6. Priority:-1 extents:1 Jun 20 23:30:15 perenold kernel: reiserfs: enabling write barrier flush mode Jun 20 23:30:15 perenold kernel: reiserfs: disabling flush barriers on hda5 Jun 20 23:30:15 perenold kernel: Real Time Clock Driver v1.12 Jun 20 23:30:15 perenold kernel: WDT driver for the Winbond(TM) W83627HF Super I/O chip initialising. Jun 20 23:30:15 perenold kernel: w83627hf WDT: initialized. timeout=60 sec (nowayout=0) Jun 20 23:30:15 perenold kernel: CSLIP: code copyright 1989 Regents of the University of California Jun 20 23:30:15 perenold kernel: PPP generic driver version 2.4.2 Jun 20 23:30:15 perenold kernel: ReiserFS: hda7: found reiserfs format "3.6" with standard journal Jun 20 23:30:15 perenold kernel: ReiserFS: hda7: using ordered data mode Jun 20 23:30:15 perenold kernel: reiserfs: using flush barriers Jun 20 23:30:15 perenold kernel: ReiserFS: hda7: journal params: device hda7, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 Jun 20 23:30:15 perenold kernel: ReiserFS: hda7: checking transaction log (hda7) Jun 20 23:30:15 perenold kernel: reiserfs: disabling flush barriers on hda7 Jun 20 23:30:15 perenold kernel: ReiserFS: hda7: Using r5 hash to sort names Jun 20 23:30:15 perenold kernel: ReiserFS: hda8: found reiserfs format "3.6" with standard journal Jun 20 23:30:15 perenold kernel: ReiserFS: hda8: using ordered data mode Jun 20 23:30:15 perenold kernel: reiserfs: using flush barriers Jun 20 23:30:15 perenold kernel: ReiserFS: hda8: journal params: device hda8, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 Jun 20 23:30:15 perenold kernel: ReiserFS: hda8: checking transaction log (hda8) Jun 20 23:30:15 perenold kernel: reiserfs: disabling flush barriers on hda8 Jun 20 23:30:15 perenold kernel: ReiserFS: hda8: Using r5 hash to sort names Jun 20 23:30:15 perenold kernel: ReiserFS: hdg1: found reiserfs format "3.6" with standard journal Jun 20 23:30:15 perenold kernel: ReiserFS: hdg1: using ordered data mode Jun 20 23:30:15 perenold kernel: reiserfs: using flush barriers Jun 20 23:30:15 perenold kernel: ReiserFS: hdg1: journal params: device hdg1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 Jun 20 23:30:15 perenold kernel: ReiserFS: hdg1: checking transaction log (hdg1) Jun 20 23:30:15 perenold kernel: ReiserFS: hdg1: Using r5 hash to sort names Jun 20 23:30:15 perenold kernel: Linux agpgart interface v0.101 (c) Dave Jones Jun 20 23:30:15 perenold kernel: agpgart: Detected VIA KT266/KY266x/KT333 chipset Jun 20 23:30:15 perenold kernel: agpgart: AGP aperture is 256M @ 0xe0000000 Jun 20 23:30:15 perenold kernel: Linux video capture interface: v1.00 Jun 20 23:30:15 perenold kernel: saa7130/34: v4l2 driver version 0.2.13 loaded Jun 20 23:30:15 perenold kernel: ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 16 (level, low) -> IRQ 17 Jun 20 23:30:15 perenold kernel: saa7134[0]: found at 0000:00:05.0, rev: 1, irq: 17, latency: 64, mmio: 0xdfffbc00 Jun 20 23:30:15 perenold kernel: saa7134[0]: subsystem: 11bd:002b, board: Pinnacle PCTV Stereo (saa7134) [card=26,autodetected] Jun 20 23:30:15 perenold kernel: saa7134[0]: board init: gpio is 0 Jun 20 23:30:15 perenold kernel: saa7134[0]: i2c eeprom 00: bd 11 2b 00 f8 f8 1c 00 43 43 a9 1c 55 d2 b2 92 Jun 20 23:30:15 perenold kernel: saa7134[0]: i2c eeprom 10: 00 00 19 0e ff 20 ff ff ff ff ff ff ff ff ff ff Jun 20 23:30:15 perenold kernel: saa7134[0]: i2c eeprom 20: 01 40 01 03 03 ff 03 01 08 ff 00 53 ff ff ff ff Jun 20 23:30:15 perenold kernel: saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff Jun 20 23:30:15 perenold kernel: tuner 1-0060: chip found @ 0xc0 (saa7134[0]) Jun 20 23:30:15 perenold kernel: tuner 1-0060: microtune: companycode=3cbf part=42 rev=11 Jun 20 23:30:15 perenold kernel: tuner 1-0060: microtune MT2050 found, OK Jun 20 23:30:15 perenold kernel: secam: string doesn't fit in 1 chars. Jun 20 23:30:15 perenold kernel: tda9887: `'L'' too large for parameter `secam' Jun 20 23:30:15 perenold kernel: saa7134[0]: registered device video0 [v4l2] Jun 20 23:30:15 perenold kernel: saa7134[0]: registered device vbi0 Jun 20 23:30:15 perenold kernel: saa7134[0]: registered device dsp0 Jun 20 23:30:15 perenold kernel: saa7134[0]: registered device mixer0 Jun 20 23:30:15 perenold kernel: 8139too Fast Ethernet driver 0.9.27 Jun 20 23:30:15 perenold kernel: ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 18 (level, low) -> IRQ 18 Jun 20 23:30:15 perenold kernel: eth0: RealTek RTL8139 at 0xe0b6ab00, 00:30:4f:28:10:f2, IRQ 18 Jun 20 23:30:15 perenold kernel: eth0: Identified 8139 chip type 'RTL-8100B/8139D' Jun 20 23:30:15 perenold kernel: ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 19 (level, low) -> IRQ 19 Jun 20 23:30:15 perenold kernel: eth1: RealTek RTL8139 at 0xe0b70a00, 00:30:4f:27:ee:39, IRQ 19 Jun 20 23:30:15 perenold kernel: eth1: Identified 8139 chip type 'RTL-8100B/8139D' Jun 20 23:30:15 perenold kernel: usbcore: registered new driver usbfs Jun 20 23:30:15 perenold kernel: usbcore: registered new driver hub Jun 20 23:30:15 perenold kernel: USB Universal Host Controller Interface driver v2.3 Jun 20 23:30:15 perenold kernel: ACPI: PCI Interrupt 0000:00:11.2[D] -> GSI 5 (level, low) -> IRQ 20 Jun 20 23:30:15 perenold kernel: PCI: Via IRQ fixup for 0000:00:11.2, from 5 to 4 Jun 20 23:30:15 perenold kernel: uhci_hcd 0000:00:11.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller Jun 20 23:30:15 perenold kernel: uhci_hcd 0000:00:11.2: new USB bus registered, assigned bus number 1 Jun 20 23:30:15 perenold kernel: uhci_hcd 0000:00:11.2: irq 20, io base 0x0000c400 Jun 20 23:30:15 perenold kernel: hub 1-0:1.0: USB hub found Jun 20 23:30:15 perenold kernel: hub 1-0:1.0: 2 ports detected Jun 20 23:30:15 perenold kernel: ACPI: PCI Interrupt 0000:00:11.3[D] -> GSI 5 (level, low) -> IRQ 20 Jun 20 23:30:15 perenold kernel: PCI: Via IRQ fixup for 0000:00:11.3, from 5 to 4 Jun 20 23:30:15 perenold kernel: uhci_hcd 0000:00:11.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2) Jun 20 23:30:15 perenold kernel: uhci_hcd 0000:00:11.3: new USB bus registered, assigned bus number 2 Jun 20 23:30:15 perenold kernel: uhci_hcd 0000:00:11.3: irq 20, io base 0x0000c800 Jun 20 23:30:15 perenold kernel: hub 2-0:1.0: USB hub found Jun 20 23:30:15 perenold kernel: hub 2-0:1.0: 2 ports detected Jun 20 23:30:15 perenold kernel: ACPI: PCI Interrupt 0000:00:11.4[D] -> GSI 5 (level, low) -> IRQ 20 Jun 20 23:30:15 perenold kernel: PCI: Via IRQ fixup for 0000:00:11.4, from 5 to 4 Jun 20 23:30:15 perenold kernel: uhci_hcd 0000:00:11.4: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3) Jun 20 23:30:15 perenold kernel: uhci_hcd 0000:00:11.4: new USB bus registered, assigned bus number 3 Jun 20 23:30:15 perenold kernel: uhci_hcd 0000:00:11.4: irq 20, io base 0x0000cc00 Jun 20 23:30:15 perenold kernel: hub 3-0:1.0: USB hub found Jun 20 23:30:15 perenold kernel: hub 3-0:1.0: 2 ports detected Jun 20 23:30:15 perenold kernel: usb 2-1: new full speed USB device using uhci_hcd and address 2 Jun 20 23:30:15 perenold kernel: via82xx: Assuming DXS channels with 48k fixed sample rate. Jun 20 23:30:15 perenold kernel: Please try dxs_support=1 or dxs_support=4 option Jun 20 23:30:15 perenold kernel: and report if it works on your machine. Jun 20 23:30:15 perenold kernel: ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 12 (level, low) -> IRQ 21 Jun 20 23:30:15 perenold kernel: PCI: Via IRQ fixup for 0000:00:11.5, from 12 to 5 Jun 20 23:30:15 perenold kernel: PCI: Setting latency timer of device 0000:00:11.5 to 64 Jun 20 23:30:15 perenold kernel: unable to register OSS PCM device 0:0 Jun 20 23:30:15 perenold kernel: irq 21: nobody cared (try booting with the "irqpoll" option. Jun 20 23:30:15 perenold kernel: [<c01329b4>] __report_bad_irq+0x24/0x80 Jun 20 23:30:15 perenold kernel: [<c0132acb>] note_interrupt+0x8b/0xe0 Jun 20 23:30:15 perenold kernel: [<c0132500>] __do_IRQ+0xe0/0xf0 Jun 20 23:30:15 perenold kernel: [<c0104efe>] do_IRQ+0x3e/0x60 Jun 20 23:30:15 perenold kernel: ======================= Jun 20 23:30:15 perenold kernel: [<c01034d6>] common_interrupt+0x1a/0x20 Jun 20 23:30:15 perenold kernel: handlers: Jun 20 23:30:15 perenold kernel: [<e0c4f420>] (snd_via82xx_interrupt+0x0/0xd0 [snd_via82xx]) Jun 20 23:30:15 perenold kernel: Disabling IRQ #21 Jun 20 23:30:15 perenold kernel: unable to register OSS mixer device 0:0 Jun 20 23:30:15 perenold kernel: drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 1 proto 2 vid 0x067B pid 0x2305 Jun 20 23:30:15 perenold kernel: usbcore: registered new driver usblp Jun 20 23:30:15 perenold kernel: drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Jun 20 23:30:15 perenold kernel: Floppy drive(s): fd0 is 1.44M Jun 20 23:30:15 perenold kernel: FDC 0 is a post-1991 82077 Jun 20 23:30:15 perenold kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled Jun 20 23:30:15 perenold kernel: ttyS0 at I/O 0x3f8 (irq = 0) is a 16550A Jun 20 23:30:15 perenold kernel: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A Jun 20 23:30:15 perenold kernel: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A Jun 20 23:30:15 perenold kernel: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A Jun 20 23:30:15 perenold kernel: parport: PnPBIOS parport detected. Jun 20 23:30:15 perenold kernel: parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA] Jun 20 23:30:15 perenold kernel: input: PC Speaker Jun 20 23:30:15 perenold kernel: ide-floppy driver 0.99.newide Jun 20 23:30:15 perenold kernel: hdb: No disk in drive Jun 20 23:30:15 perenold kernel: hdb: 98304kB, 96/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm Jun 20 23:30:15 perenold kernel: hdc: ATAPI 32X DVD-ROM drive, 256kB Cache, UDMA(33) Jun 20 23:30:15 perenold kernel: Uniform CD-ROM driver Revision: 3.20 Jun 20 23:30:15 perenold kernel: hdd: ATAPI 40X CD-ROM CD-R/RW drive, 4096kB Cache, UDMA(33) Jun 20 23:30:15 perenold kernel: Bridge firewalling registered Jun 20 23:30:15 perenold kernel: device eth0 entered promiscuous mode Jun 20 23:30:15 perenold kernel: eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 Jun 20 23:30:15 perenold kernel: eth0: Promiscuous mode enabled. Jun 20 23:30:15 perenold kernel: eth0: Promiscuous mode enabled. Jun 20 23:30:15 perenold kernel: eth0: Promiscuous mode enabled. Jun 20 23:30:15 perenold kernel: eth0: Promiscuous mode enabled. Jun 20 23:30:15 perenold kernel: eth0: Promiscuous mode enabled. Jun 20 23:30:15 perenold kernel: device eth1 entered promiscuous mode Jun 20 23:30:15 perenold kernel: eth1: link up, 100Mbps, full-duplex, lpa 0x45E1 Jun 20 23:30:15 perenold kernel: eth1: Promiscuous mode enabled. Jun 20 23:30:15 perenold kernel: eth1: Promiscuous mode enabled. Jun 20 23:30:15 perenold kernel: eth1: Promiscuous mode enabled. Jun 20 23:30:15 perenold kernel: eth1: Promiscuous mode enabled. Jun 20 23:30:15 perenold kernel: eth1: Promiscuous mode enabled. Jun 20 23:30:15 perenold kernel: br0: port 2(eth1) entering learning state Jun 20 23:30:15 perenold kernel: br0: port 1(eth0) entering learning state Jun 20 23:30:15 perenold kernel: br0: topology change detected, propagating Jun 20 23:30:15 perenold kernel: br0: port 2(eth1) entering forwarding state Jun 20 23:30:15 perenold kernel: br0: topology change detected, propagating Jun 20 23:30:15 perenold kernel: br0: port 1(eth0) entering forwarding state Jun 20 23:30:15 perenold kernel: NET: Registered protocol family 17 Jun 20 23:30:15 perenold kernel: ip_conntrack version 2.1 (4095 buckets, 32760 max) - 248 bytes per conntrack Jun 20 23:30:15 perenold kernel: Ebtables v2.0 registered Jun 20 23:30:15 perenold kernel: ip_tables: (C) 2000-2002 Netfilter core team Jun 20 23:30:36 perenold kernel: ACPI: Processor [CPU1] (supports 16 throttling states) Jun 20 23:30:36 perenold kernel: ACPI: Power Button (FF) [PWRF] Jun 20 23:30:36 perenold kernel: ACPI: Sleep Button (CM) [SLPB] Jun 20 23:30:39 perenold kernel: device br0 entered promiscuous mode Jun 20 23:30:40 perenold kernel: uhci_hcd 0000:00:11.3: Unlink after no-IRQ? Controller is probably using the wrong IRQ. Jun 20 23:30:49 perenold kernel: tuner 1-0060: Cmd VIDIOC_S_STD accepted to TV Jun 20 23:30:49 perenold kernel: tuner 1-0060: Cmd VIDIOC_S_STD accepted to TV Jun 20 23:30:49 perenold kernel: tuner 1-0060: Cmd VIDIOC_S_STD accepted to TV Jun 20 23:30:49 perenold kernel: saa7134[0]/irq[10,-51080]: r=0x20 s=0x00 PE Jun 20 23:30:49 perenold kernel: saa7134[0]/irq: looping -- clearing PE (parity error!) enable bit Jun 20 23:30:49 perenold kernel: tuner 1-0060: Cmd VIDIOC_S_FREQUENCY accepted to TV
-- Mathieu Bérard
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |