lkml.org 
[lkml]   [2005]   [May]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: ide-cd vs. DMA

Benjamin Herrenschmidt wrote:
> Well, not sure what's wrong here, but ATAPI errors shouldn't normally
> result in stopping DMA. We may want to just blacklist your drive rather
> than having this stupid fallback. In this case, I suspect it's
> CSS/region issue with a DVD.

Here's a little bit more info:

Here's from dmesg:
hdc: SAMSUNG SC-140B, ATAPI CD/DVD-ROM drive
hdc: ATAPI 40X CD-ROM drive, 128kB Cache, UDMA(33)

hdparm -i /dev/hdc:

/dev/hdc:

Model=SAMSUNG SC-140B, FwRev=d005, SerialNo=
Config={ SpinMotCtl Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic }
RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=0kB, MaxMultSect=0
(maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2
AdvancedPM=no

Here's what happens on the first mount attempt:
hdc: DMA interrupt recovery
hdc: lost interrupt
hdc: status timeout: status=0xd0 { Busy }
hdc: status timeout: error=0x00
hdc: DMA disabled
hdc: drive not ready for command
hdc: ATAPI reset complete

Now, if I'm stuborn and re-enable DMA using a "hdparm -d1 /dev/hdc" and then
try again, now I get:
hdc: media error (bad sector): status=0x51 { DriveReady SeekComplete Error }
hdc: media error (bad sector): error=0x34
ide: failed opcode was 100
end_request: I/O error, dev hdc, sector 16

The last error being repeated ad-nauseam for every "sector" on the
disk. Again, note that this is a CD drive, not a hard disk.

Here's from lspci:
00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03)
00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01)
00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01)
00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
00:11.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 24)
01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage Pro AGP 1X/2X (rev 5c)

In attempting to isolate the problem, I ran into a spurious issue with
another drive I have in that machine:
hda: dma_timer_expiry: dma status == 0x61
hda: DMA timeout error
hda: dma timeout error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: dma_timer_expiry: dma status == 0x61
hda: DMA timeout error
hda: dma timeout error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: dma_timer_expiry: dma status == 0x61
hda: DMA timeout error
hda: dma timeout error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: dma_timer_expiry: dma status == 0x61
hda: DMA timeout error
hda: dma timeout error: status=0x58 { DriveReady SeekComplete DataRequest }
hda: DMA disabled

Try as I may, however, I haven't been able to reproduce this problem with
hda (from dmesg: hda: WDC AC22500L, ATA DISK drive). It's worthy pointing
out that the machine came with a drive on which it was found that there
were actual bad sectors (tested on another machine.) ... the thought of
a buggy controller came to mind, but (though this may be possible), I've
never heard about a bad controller generating bad sectors ...

Karim
--
Author, Speaker, Developer, Consultant
Pushing Embedded and Real-Time Linux Systems Beyond the Limits
http://www.opersys.com || karim@opersys.com || 1-866-677-4546
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-05-24 05:55    [W:2.927 / U:0.008 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site