lkml.org 
[lkml]   [2005]   [Feb]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[PATCH][PPC32] Move irq_desc[].status, IRQ_LEVEL bit setup to xilinx_pic.c
This patch applies to the kernel 2.6.11-rc3.
It moves the code that informs the kernel if the particular interrupt is edge triggered
or level sensitive from the board specific file to a "CONFIG_VIRTEX_II_PRO-specific" file.
Using old IRQ numbering in that code is also fixed.

Signed-off-by: Andrei Konovalov <akonovalov@ru.mvista.com>

diff -uprN linux-2.5.base/arch/ppc/platforms/4xx/xilinx_ml300.c linux-2.5.cur/arch/ppc/platforms/4xx/xilinx_ml300.c
--- linux-2.5.base/arch/ppc/platforms/4xx/xilinx_ml300.c 2005-02-11 17:19:08.000000000 +0300
+++ linux-2.5.cur/arch/ppc/platforms/4xx/xilinx_ml300.c 2005-02-14 18:37:26.000000000 +0300
@@ -122,25 +122,7 @@ ml300_setup_arch(void)
void __init
ml300_init_irq(void)
{
- unsigned int i;
-
ppc4xx_init_IRQ();
-
- /*
- * For PowerPC 405 cores the default value for NR_IRQS is 32.
- * See include/asm-ppc/irq.h for details.
- * This is just fine for ML300.
- */
-#if (NR_IRQS != 32)
-#error NR_IRQS must be 32 for ML300
-#endif
-
- for (i = 0; i < NR_IRQS; i++) {
- if (XPAR_INTC_0_KIND_OF_INTR & (0x80000000 >> i))
- irq_desc[i].status &= ~IRQ_LEVEL;
- else
- irq_desc[i].status |= IRQ_LEVEL;
- }
}

void __init
diff -uprN linux-2.5.base/arch/ppc/syslib/xilinx_pic.c linux-2.5.cur/arch/ppc/syslib/xilinx_pic.c
--- linux-2.5.base/arch/ppc/syslib/xilinx_pic.c 2005-02-11 17:20:49.000000000 +0300
+++ linux-2.5.cur/arch/ppc/syslib/xilinx_pic.c 2005-02-14 16:57:40.000000000 +0300
@@ -114,6 +114,14 @@ ppc4xx_pic_init(void)
{
int i;

+ /*
+ * NOTE: The assumption here is that NR_IRQS is 32 or less
+ * (NR_IRQS is 32 for PowerPC 405 cores by default).
+ */
+#if (NR_IRQS > 32)
+#error NR_IRQS > 32 not supported
+#endif
+
#if XPAR_XINTC_USE_DCR == 0
intc = ioremap(XPAR_INTC_0_BASEADDR, 32);

@@ -138,6 +146,12 @@ ppc4xx_pic_init(void)

ppc_md.get_irq = xilinx_pic_get_irq;

- for (i = 0; i < NR_IRQS; ++i)
+ for (i = 0; i < NR_IRQS; ++i) {
irq_desc[i].handler = &xilinx_intc;
+
+ if (XPAR_INTC_0_KIND_OF_INTR & (0x00000001 << i))
+ irq_desc[i].status &= ~IRQ_LEVEL;
+ else
+ irq_desc[i].status |= IRQ_LEVEL;
+ }
}
\
 
 \ /
  Last update: 2005-03-22 14:10    [W:0.196 / U:0.236 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site