Messages in this thread Patch in this message | | | Subject | [PATCH] Re: bug in handling of highspeed usb HID devices | From | Christian Krause <> | Date | Sat, 15 Oct 2005 10:24:23 +0200 |
| |
Hi Greg,
On Fri, 14 Oct 2005 19:18:18 -0700, Greg KH wrote: >> > Did you try this patch out? ?It is wrong. ?Please look at the >> > compiler warning that this change generates and redo the patch.
> Which leads me to believe that Christian never tried the patch :(
I'm very sorry, it seems that my first linux kernel patch will be a real desaster.
Unfortunately, Greg, you are right. To get a real clean patch without my debug printks I've made my changes again on a clean kernel tree and so I missed a line and I did not recompile the kernel again before submitting the patch. I'm mortified, but I've learned the lesson - it will never happen again. Here is the next try:
This patch compiles cleanly on a vanilla kernel 2.6.13.4 and I've tested that it fixes the problem - the interval for highspeed HID devices is correctly set.
explanation and patch:
During the development of an USB device I found a bug in the handling of Highspeed HID devices in the kernel.
What happened?
Highspeed HID devices are correctly recognized and enumerated by the kernel. But even if usbhid kernel module is loaded, no HID reports are received by the kernel.
The output of the hardware USB analyzer told me that the host doesn't even poll for interrupt IN transfers (even the "interrupt in" USB transfer are polled by the host).
After some debugging in hid-core.c I've found the reason.
In case of a highspeed device, the endpoint interval is re-calculated in driver/usb/input/hid-core.c:
line 1669: /* handle potential highspeed HID correctly */ interval = endpoint->bInterval; if (dev->speed == USB_SPEED_HIGH) interval = 1 << (interval - 1);
Basically this calculation is correct (refer to USB 2.0 spec, 9.6.6). This new calculated value of "interval" is used as input for usb_fill_int_urb:
line 1685:
usb_fill_int_urb(hid->urbin, dev, pipe, hid->inbuf, 0, hid_irq_in, hid, interval);
Unfortunately the same calculation as above is done a second time in usb_fill_int_urb in the file include/linux/usb.h:
line 933: if (dev->speed == USB_SPEED_HIGH) urb->interval = 1 << (interval - 1); else urb->interval = interval;
This means, that if the endpoint descriptor (of a high speed device) specifies e.g. bInterval = 7, the urb->interval gets the value:
hid-core.c: interval = 1 << (7-1) = 0x40 = 64 urb->interval = 1 << (interval -1) = 1 << (63) = integer overflow
Because of this the value of urb->interval is sometimes negative and is rejected in core/urb.c: line 353: /* too small? */ if (urb->interval <= 0) return -EINVAL;
The conclusion is, that the recalculaton of the interval (which is necessary for highspeed) should not be made twice, because this is simply wrong. ;-)
Re-calculation in usb_fill_int_urb makes more sense, because it is the most general approach. So it would make sense to remove it from hid-core.c.
Because in hid-core.c the interval variable is only used for calling usb_fill_int_urb, it is no problem to remove the highspeed re-calculation in this file.
Signed-off-by: Christian Krause <chkr@plauener.de>
--------------------snip---------------------- --- linux-2.6.13.4/drivers/usb/input/hid-core.c.old 2005-10-15 09:24:22.000000000 +0200 +++ linux-2.6.13.4/drivers/usb/input/hid-core.c 2005-10-15 09:55:50.000000000 +0200 @@ -1667,10 +1667,7 @@ static struct hid_device *usb_hid_config if ((endpoint->bmAttributes & 3) != 3) /* Not an interrupt endpoint */ continue; - /* handle potential highspeed HID correctly */ interval = endpoint->bInterval; - if (dev->speed == USB_SPEED_HIGH) - interval = 1 << (interval - 1); /* Change the polling interval of mice. */ if (hid->collection->usage == HID_GD_MOUSE && hid_mousepoll_interval > 0) --------------------snip----------------------
Best regards, Christian - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |