lkml.org 
[lkml]   [2004]   [Aug]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
SubjectRe: TG3 doesn't work in kernel 2.4.27 (Resolved!)
From
Date
Hello, David.

In message <20040817110248.4c2f7cd8.davem@redhat.com>
"Re: TG3 doesn't work in kernel 2.4.27"
""David S. Miller" <davem@redhat.com>" wrote:

> On Tue, 17 Aug 2004 21:30:06 +0900
> Tetsuo Handa <a5497108@anet.ne.jp> wrote:
>
> > I compiled as a UP kernel but it wasn't the cause.
> > Also, I patched the above fix on 2.4.27-rc4 and
> > compiled as a UP kernel, but didn't work.
>
> Just add this patch, it will fix the problem but it
> is not the nicest fix. I'll work on a better one.
>
> It just disables the new Sun code, and uses the old
> fiber handling for 5704.
>
It resolved the problem. It works on SMP kernel, too.
The line position was different for tg3.c in 2.4.27 .

-----START-----
--- tg3.c.org 2004-08-08 08:26:05.000000000 +0900
+++ tg3.c 2004-08-18 09:27:58.000000000 +0900
@@ -5264,7 +5264,7 @@
* is enabled.
*/
tw32_f(MAC_LOW_WMARK_MAX_RX_FRAME, 2);
-
+#if 0
if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5704 &&
tp->phy_id == PHY_ID_SERDES) {
/* Enable hardware link auto-negotiation */
@@ -5284,7 +5284,7 @@

tp->tg3_flags2 |= TG3_FLG2_HW_AUTONEG;
}
-
+#endif
err = tg3_setup_phy(tp, 1);
if (err)
return err;
-----END-----
Also, as you have mentioned that this bug can only affect 5704 chips with fiber interfaces,
I found that the box has BCM5704S. The following is the result of 'lspci -vv'.

-----START-----
00:00.0 Host bridge: ServerWorks CNB20-HE Host Bridge (rev 33)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:00.1 Host bridge: ServerWorks CNB20-HE Host Bridge
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:00.2 Host bridge: ServerWorks CNB20-HE Host Bridge
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:01.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27) (prog-if 00 [VGA])
Subsystem: IBM: Unknown device 0240
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 20
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at 2200 [size=256]
Region 2: Memory at febff000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [5c] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0f.0 Host bridge: ServerWorks CSB6 South Bridge (rev b0)
Subsystem: ServerWorks: Unknown device 0201
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64

00:0f.1 IDE interface: ServerWorks CSB6 RAID/IDE Controller (rev b0) (prog-if 8a [Master SecP PriP])
Subsystem: ServerWorks: Unknown device 0212
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 08
Region 0: I/O ports at <ignored>
Region 1: I/O ports at <ignored>
Region 2: I/O ports at <ignored>
Region 3: I/O ports at <ignored>
Region 4: I/O ports at 0700 [size=16]

00:0f.2 USB Controller: ServerWorks CSB6 OHCI USB Controller (rev 05) (prog-if 10 [OHCI])
Subsystem: ServerWorks: Unknown device 0220
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max), cache line size 08
Interrupt: pin A routed to IRQ 7
Region 0: Memory at febfe000 (32-bit, non-prefetchable) [size=4K]
00:0f.3 ISA bridge: ServerWorks GCLE-2 Host Bridge
Subsystem: ServerWorks: Unknown device 0230
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0

00:10.0 Host bridge: ServerWorks: Unknown device 0110 (rev 12)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Capabilities: [60] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=4
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
00:10.2 Host bridge: ServerWorks: Unknown device 0110 (rev 12)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Capabilities: [60] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=4
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
01:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5704S Gigabit Ethernet (rev 02)
Subsystem: IBM: Unknown device 029c
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (16000ns min), cache line size 08
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fbff0000 (64-bit, non-prefetchable) [size=64K]
Region 2: Memory at fbfe0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [40] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=2 OST=0
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM- Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
Address: 0000000100000000 Data: c065
01:00.1 Ethernet controller: Broadcom Corporation NetXtreme BCM5704S Gigabit Ethernet (rev 02)
Subsystem: IBM: Unknown device 029c
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (16000ns min), cache line size 08
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fbfd0000 (64-bit, non-prefetchable) [size=64K]
Region 2: Memory at fbfc0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [40] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=2 OST=0
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM- Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
Address: 0000000100000000 Data: bef5
02:02.0 Fibre Channel: QLogic Corp. QLA2312 Fibre Channel Adapter (rev 02)
Subsystem: IBM: Unknown device 027d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (16000ns min), cache line size 08
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 2400 [size=256]
Region 1: Memory at f9ffe000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [4c] PCI-X non-bridge device.
Command: DPERE- ERO+ RBC=0 OST=2
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM- Capabilities: [54] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [64] #06 [0080]
02:02.1 Fibre Channel: QLogic Corp. QLA2312 Fibre Channel Adapter (rev 02)
Subsystem: IBM: Unknown device 027d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (16000ns min), cache line size 08
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at 2600 [size=256]
Region 1: Memory at f9ffc000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [4c] PCI-X non-bridge device.
Command: DPERE- ERO+ RBC=0 OST=2
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM- Capabilities: [54] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [64] #06 [0080]
-----END-----
Thank you very much.
-----
Tetsuo Handa
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
\
 
 \ /
  Last update: 2005-03-22 14:05    [W:0.053 / U:0.268 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site