lkml.org 
[lkml]   [2004]   [Jun]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Subjectide errors in 7-rc1-mm1 and later
Date
Hi,

I am still getting these ide errors with 7-rc2-mm2. I get the errors even
if I mount with barrier=0 (or just defaults). It would seem that something is
sending my drive commands it does not understand...

May 27 18:18:05 bert kernel: hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
May 27 18:18:05 bert kernel: hda: drive_cmd: error=0x04 { DriveStatusError }

How can we find out what is wrong?

This does not seem to be an error that corrupts the fs, it just slows things
down when it hits a group of these. Note that they keep poping up - they
do stop (I still get them hours after booting).

TIA
Ed Tomlinson

----------------------
7-mm4 ok
7-mm5 na
7-rc1-mm1 errors
7-rc2 ok
7-rc2-mm2 errors

CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y

#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
# CONFIG_IDEDISK_STROKE is not set
CONFIG_BLK_DEV_IDECD=m
CONFIG_BLK_DEV_IDETAPE=m
# CONFIG_BLK_DEV_IDEFLOPPY is not set
CONFIG_BLK_DEV_IDESCSI=m
# CONFIG_IDE_TASK_IOCTL is not set
CONFIG_IDE_TASKFILE_IO=y

#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
# CONFIG_BLK_DEV_CMD640 is not set
CONFIG_BLK_DEV_IDEPNP=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_BLK_DEV_GENERIC is not set
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
CONFIG_BLK_DEV_ADMA=y
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_BLK_DEV_ATIIXP is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_SC1200 is not set
CONFIG_BLK_DEV_PIIX=y
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_IDE_ARM is not set
# CONFIG_IDE_CHIPSETS is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y

> Think this is not just a barrier problem (unless barrier is the default).
> One if my two drives gets the error below during operation.
> The drive is the root drive and is mounted with defaults. 2.6.6-mm4
> was the last kernel booted on this box. The 2.6.7-rc1-mm1 was compiled
> with 2.95 with the following fs options:
>
> CONFIG_EXT2_FS=y
> # CONFIG_EXT2_FS_XATTR is not set
> CONFIG_EXT3_FS=m
> # CONFIG_EXT3_FS_XATTR is not set
> CONFIG_JBD=m
> # CONFIG_JBD_DEBUG is not set
> CONFIG_REISERFS_FS=y
> # CONFIG_REISERFS_CHECK is not set
> # CONFIG_REISERFS_PROC_INFO is not set
> # CONFIG_REISERFS_FS_XATTR is not set
> # CONFIG_JFS_FS is not set
> # CONFIG_XFS_FS is not set
> # CONFIG_MINIX_FS is not set
> # CONFIG_ROMFS_FS is not set
> # CONFIG_QUOTA is not set
> # CONFIG_AUTOFS_FS is not set
> CONFIG_AUTOFS4_FS=m

Disk /dev/hda: 6448 MB, 6448619520 bytes
240 heads, 63 sectors/track, 833 cylinders
Units = cylinders of 15120 * 512 = 7741440 bytes

Device Boot Start End Blocks Id System
/dev/hda1 1 99 748408+ 82 Linux swap
/dev/hda2 100 108 68040 83 Linux
/dev/hda3 * 109 833 5481000 83 Linux

> hda reports:
> root@bert:/usr/src/linux# hdparm -iI /dev/hda
>
> /dev/hda:
>
> Model=WDC AC26400R, FwRev=15.01J15, SerialNo=WD-WM6271600165
> Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
> RawCHS=13328/15/63, TrkSize=57600, SectSize=600, ECCbytes=40
> BuffType=DualPortCache, BuffSize=512kB, MaxMultSect=16, MultSect=16
> CurCHS=13328/15/63, CurSects=12594960, LBA=yes, LBAsects=12594960
> IORDY=on/off, tPIO={min:160,w/IORDY:120}, tDMA={min:120,rec:120}
> PIO modes: pio0 pio1 pio2 pio3 pio4
> DMA modes: mdma0 mdma1 mdma2
> UDMA modes: udma0 udma1 *udma2 udma3 udma4
> AdvancedPM=no WriteCache=enabled
> Drive conforms to: device does not report version: 1 2 3 4
>
> * signifies the current active mode
>
>
> ATA device, with non-removable media
> Model Number: WDC AC26400R
> Serial Number: WD-WM6271600165
> Firmware Revision: 15.01J15
> Standards:
> Supported: 4 3 2 1
> Likely used: 4
> Configuration:
> Logical max current
> cylinders 13328 13328
> heads 15 15
> sectors/track 63 63
> --
> bytes/track: 57600 bytes/sector: 600
> CHS current addressable sectors: 12594960
> LBA user addressable sectors: 12594960
> device size with M = 1024*1024: 6149 MBytes
> device size with M = 1000*1000: 6448 MBytes (6 GB)
> Capabilities:
> LBA, IORDY(can be disabled)
> Buffer size: 512.0kB bytes avail on r/w long: 40 Queue depth: 1
> Standby timer values: spec'd by Standard, no device specific minimum
> R/W multiple sector transfer: Max = 16 Current = 16
> DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4
> Cycle time: min=120ns recommended=120ns
> PIO: pio0 pio1 pio2 pio3 pio4
> Cycle time: no flow control=160ns IORDY flow control=120ns
> Commands/features:
> Enabled Supported:
> * READ BUFFER cmd
> * WRITE BUFFER cmd
> * Look-ahead
> * Write cache
> * Power Management feature set
> * SMART feature set
>
> root@bert:/usr/src/linux# hdparm -iI /dev/hdb
>
> /dev/hdb:
>
> Model=Maxtor 6E030L0, FwRev=NAR61590, SerialNo=E178CV5E
> Config={ Fixed }
> RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
> BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
> CurCHS=17475/15/63, CurSects=16513875, LBA=yes, LBAsects=60058656
> IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
> PIO modes: pio0 pio1 pio2 pio3 pio4
> DMA modes: mdma0 mdma1 mdma2
> UDMA modes: udma0 udma1 *udma2 udma3 udma4 udma5 udma6
> AdvancedPM=yes: disabled (255) WriteCache=enabled
> Drive conforms to: (null):
>
> * signifies the current active mode
>
>
> ATA device, with non-removable media
> Model Number: Maxtor 6E030L0
> Serial Number: E178CV5E
> Firmware Revision: NAR61590
> Standards:
> Supported: 7 6 5 4
> Likely used: 7
> Configuration:
> Logical max current
> cylinders 16383 17475
> heads 16 15
> sectors/track 63 63
> --
> CHS current addressable sectors: 16513875
> LBA user addressable sectors: 60058656
> device size with M = 1024*1024: 29325 MBytes
> device size with M = 1000*1000: 30750 MBytes (30 GB)
> Capabilities:
> LBA, IORDY(can be disabled)
> Queue depth: 1
> Standby timer values: spec'd by Standard, no device specific minimum
> R/W multiple sector transfer: Max = 16 Current = 16
> Advanced power management level: unknown setting (0x0000)
> Recommended acoustic management value: 192, current value: 254
> DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5 udma6
> Cycle time: min=120ns recommended=120ns
> PIO: pio0 pio1 pio2 pio3 pio4
> Cycle time: no flow control=120ns IORDY flow control=120ns
> Commands/features:
> Enabled Supported:
> * NOP cmd
> * READ BUFFER cmd
> * WRITE BUFFER cmd
> * Host Protected Area feature set
> * Look-ahead
> * Write cache
> * Power Management feature set
> Security Mode feature set
> * SMART feature set
> * FLUSH CACHE EXT command
> * Mandatory FLUSH CACHE command
> * Device Configuration Overlay feature set
> * Automatic Acoustic Management feature set
> SET MAX security extension
> Advanced Power Management feature set
> * DOWNLOAD MICROCODE cmd
> * SMART self-test
> * SMART error logging
> Security:
> Master password revision code = 65534
> supported
> not enabled
> not locked
> not frozen
> not expired: security count
> not supported: enhanced erase
> HW reset results:
> CBLID- above Vih
> Device num = 1 determined by CSEL
> Checksum: correct
>
> hdb is accessed via dm and evms. This is what the boot of reports:
>
> May 27 18:17:39 bert kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> May 27 18:17:39 bert kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> May 27 18:17:39 bert kernel: PIIX4: IDE controller at PCI slot 0000:00:14.1
> May 27 18:17:39 bert kernel: PIIX4: chipset revision 1
> May 27 18:17:39 bert kernel: PIIX4: not 100%% native mode: will probe irqs later
> May 27 18:17:39 bert kernel: ide0: BM-DMA at 0x10c0-0x10c7, BIOS settings: hda:pio, hdb:DMA
> May 27 18:17:39 bert kernel: ide1: BM-DMA at 0x10c8-0x10cf, BIOS settings: hdc:DMA, hdd:pio
> May 27 18:17:39 bert kernel: hda: WDC AC26400R, ATA DISK drive
> May 27 18:17:39 bert kernel: hdb: Maxtor 6E030L0, ATA DISK drive
> May 27 18:17:39 bert kernel: Using anticipatory io scheduler
> May 27 18:17:39 bert kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> May 27 18:17:39 bert kernel: hdc: HL-DT-ST RW/DVD GCC-4480B, ATAPI CD/DVD-ROM drive
> May 27 18:17:39 bert kernel: ide1 at 0x170-0x177,0x376 on irq 15
> May 27 18:17:39 bert kernel: pnp: the driver 'ide' has been registered
> May 27 18:17:39 bert kernel: hda: max request size: 128KiB
> May 27 18:17:39 bert kernel: hda: 12594960 sectors (6448 MB) w/512KiB Cache, CHS=13328/15/63, UDMA(33)
> May 27 18:17:39 bert kernel: hda: cache flushes supported
> May 27 18:17:39 bert kernel: hda: hda1 hda2 hda3
> May 27 18:17:39 bert kernel: hdb: max request size: 128KiB
> May 27 18:17:39 bert kernel: hdb: 60058656 sectors (30750 MB) w/2048KiB Cache, CHS=59582/16/63, UDMA(33)
> May 27 18:17:39 bert kernel: hdb: cache flushes supported
> May 27 18:17:39 bert kernel: hdb: hdb1 hdb2 hdb3 hdb4 < hdb5 >
>
> followed later by:
>
> May 27 18:18:05 bert kernel: hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
> May 27 18:18:05 bert kernel: hda: drive_cmd: error=0x04 { DriveStatusError }
> May 27 18:18:06 bert kernel: hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
> May 27 18:18:06 bert kernel: hda: drive_cmd: error=0x04 { DriveStatusError }
> May 27 18:19:21 bert kernel: hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
> May 27 18:19:21 bert kernel: hda: drive_cmd: error=0x04 { DriveStatusError }
> May 27 18:19:22 bert kernel: hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
> May 27 18:19:22 bert kernel: hda: drive_cmd: error=0x04 { DriveStatusError }
> May 27 18:20:01 bert kernel: hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
> May 27 18:20:01 bert kernel: hda: drive_cmd: error=0x04 { DriveStatusError }
> May 27 18:20:01 bert kernel: hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
> May 27 18:20:01 bert kernel: hda: drive_cmd: error=0x04 { DriveStatusError }
> May 27 18:21:27 bert kernel: hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
> May 27 18:21:27 bert kernel: hda: drive_cmd: error=0x04 { DriveStatusError }
>
>
>
>
> Hope this help,
>
> Ed
>
> On May 27, 2004 04:24 pm, Günther Persoons wrote:
> > Hey,
> > When i mount my reiser partitie with the option barrier=flush i get
> > following message and error:
> > My harddrive is a 2.5 inch Fujitsu 20GB IDE.
> >
> > mount /dev/hda10 /tmp -o barrier=flush
> > mount: wrong fs type, bad option, bad superblock on /dev/hda10,
> > or too many mounted file systems
> > Log:
> > ReiserFS: hda10: found reiserfs format "3.6" with standard journal
> > ReiserFS: hda10: using ordered data mode
> > reiserfs: using flush barriers
> > ReiserFS: hda10: journal params: device hda10, size 8192, journal first
> > block 18, max trans len 1024, max batch 900, max commit age 30, max
> > trans age 30
> > ReiserFS: hda10: checking transaction log (hda10)
> > hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
> > hda: drive_cmd: error=0x04 { DriveStatusError }
> > hda: barrier support doesn't work
> > ReiserFS: hda10: warning: journal-837: IO error during journal replay
> > ReiserFS: hda10: warning: Replay Failure, unable to mount
> > ReiserFS: hda10: warning: sh-2022: reiserfs_fill_super: unable to
> > initialize journal space
>
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 14:03    [W:0.170 / U:0.844 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site